ETSI ETS 300 494-3 ed.1 (1996-08)

Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile Test Specification (PTS); Part 3: Profile Specific Test Specification (PSTS) - Fixed radio Termination (FT)

DE/RES-03040-3

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Profil generičnega dostopa (GAP) - 3. del: Od profila odvisna preskušalna specifikacija (PSTS) - fiksna radijska zaključitev (FT)

General Information

• Status: Published
• Publication Date: 01-Sep-1996
• Technical Committee: RES 3 - DECT
• Current Stage: 12 - Completion
• Due Date: 06-Sep-1996
• Completion Date: 02-Sep-1996
• Mandate: T-317
• Ref Project: SIST ETS 300 494-3:1999 - Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile Test Specification (PTS); Part 3: Profile Specific Test Specification (PSTS) - Fixed radio Termination (FT)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile Test Specification (PTS); Part 3: Profile Specific Test Specification (PSTS) - Fixed radio Termination (FT)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 494-3 E13SIST ETS 300 494-3:1999en01MDQXDU-19993SIST ETS 300 494-3:1999SLOVENSKI
STANDARD



SIST ETS 300 494-3:1999



EUROPEANETS 300 494-3TELECOMMUNICATIONAugust 1996STANDARDSource: ETSI TC-RESReference: DE/RES-03040-3ICS:33.020, 33.060.50Key words:DECT, GAP, testingRadio Equipment and Systems (RES);Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile Test Specification (PTS);Part 3: Profile Specific Test Specification (PSTS)- Fixed radio Termination (FT)ETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: [e-mail].: [phone] - Fax: [phone]Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1996. All rights reserved.SIST ETS 300 494-3:1999



Page 2ETS 300 494-3: August 1996Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 494-3:1999



Page 3ETS 300 494-3: August 1996ContentsForeword.71Scope.92Normative references.93Definitions and abbreviations.123.1Definitions.123.2Abbreviations.124Relevant test cases list.134.1Network (NWK) layer.134.1.1Test suite structure.134.1.2Test case index.154.2Data Link Control (DLC) layer.194.2.1Test suite structure.194.2.2Test case index.204.3Medium Access Control (MAC) layer.214.3.1Test suite structure.224.3.2Test case index.244.4Physical (PH) layer.254.4.1Manufacturer declarations.254.4.2Normal Transmitted Power (NTP).254.4.2.1Verdict criteria for IUTs with an integral antenna.254.4.2.2Verdict criteria for IUTs with external antennaconnection(s).254.4.3RFP radio receiver sensitivity.254.4.4Radio receiver interference performance.264.4.5Receiver intermodulation performance.265Additional test cases list.265.1Test purposes.265.1.1NWK layer.265.1.2DLC layer.265.1.3MAC layer.265.1.4PH layer.265.2Test cases.265.2.1NWK layer.265.2.2DLC layer.265.2.3MAC layer.275.2.4PH layer.275.2.4.1Receiver sensitivity tolerance of transmitter deviationvariations.275.2.4.1.1Definition.275.2.4.1.2Test environment.275.2.4.1.3Method of measurement.275.2.4.1.4Verdict criteria.285.2.4.2Transmission of Z-field.285.2.4.2.1Definition.285.2.4.2.2Test environment.285.2.4.2.3Method of measurement.285.2.4.2.4Verdict criteria.28SIST ETS 300 494-3:1999



Page 4ETS 300 494-3: August 1996Annex A (normative):Profile Implementation eXtra Information for Testing (IXIT) proforma.29A.1General.29A.2Profile IXIT Requirements List (XRL).29A.2.1NWK layer protocol.29A.2.1.1Addresses.29A.2.1.2Parameter values.29A.2.1.3Timer values.29A.2.1.4Counters values.29A.2.1.5Protocol constants values.30A.2.1.6Control of Protocol Data Units (PDU) sending.30A.2.2DLC layer protocol.30A.2.2.1Addresses.30A.2.2.2Parameter values.30A.2.2.3Timer values.30A.2.2.4Counters values.30A.2.2.5Protocol constants values.31A.2.2.6Control of PDU sending.31A.2.3MAC layer protocol.31A.2.3.1Addresses.31A.2.3.2Parameter values.31A.2.3.3Timer values.31A.2.3.4Counters values.31A.2.3.5Protocol constants values.31A.2.3.6Control of PDU sending.32A.2.4PH layer protocol.32A.2.4.1Addresses.32A.2.4.2Parameter values.32A.2.4.3Timer values.32A.2.4.4Counters values.32A.2.4.5Protocol constants values.32A.2.4.6Control of PDU sending.32A.3Profile specific IXIT.32A.3.1NWK layer.32A.3.2DLC layer.32A.3.3MAC layer.33A.3.4PH layer.33A.3.5Configuration constraints.33Annex B (normative):Profile Conformance Test Report (PCTR) proforma.34B.1Identification summary.34B.1.1PCTR.34B.1.2Implementation Under Test (IUT).35B.1.3Testing environment.35B.1.4Limits and reservations.35B.1.5Comments.36B.2IUT conformance status.36B.3Static conformance summary.36B.4Dynamic conformance summary.36B.5Static conformance review report.37SIST ETS 300 494-3:1999



Page 5ETS 300 494-3: August 1996B.6Test campaign report.37B.6.1NWK layer.38B.6.2DLC layer.40B.6.3MAC layer.41B.6.4PH layer.41B.7Observations.42Annex C (normative):System Conformance Test Report (SCTR) proforma.43C.1Identification summary.43C.1.1SCTR.43C.1.2Test laboratory.43C.1.3Client.44C.1.4System Under Test (SUT).44C.1.5Profile.44C.1.6Nature of conformance testing.45C.1.7Limits and reservations.45C.1.8Record of agreement.45C.1.9Comments.45C.2System report summary.46C.2.1Profile testing summary for GAP NWK layer FT.46C.2.2Profile testing summary for GAP DLC layer FT.47C.2.3Profile testing summary for GAP MAC layer FT.48C.2.4Profile testing summary for GAP PH layer FT.49Annex D (normative):System Conformance Statement (SCS) proforma.50D.1Identification summary.50D.1.1SCS identification.50D.1.2IUT identification.50D.1.3Client identification.50D.1.4Supplier identification.51D.1.5Manufacturer identification.52D.1.6Protocols identification.52D.1.7Profile identification.52D.2Miscellaneous System Information.52D.2.1Configuration.52D.2.2Other information.53History.54SIST ETS 300 494-3:1999



Page 6ETS 300 494-3: August 1996Blank pageSIST ETS 300 494-3:1999



Page 7ETS 300 494-3: August 1996ForewordThis European Telecommunication Standard (ETS) has been produced by the Radio Equipment andSystems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).The General Access Profile (GAP) Profile Test Specification (PTS) comprises three parts:Part 1:"Summary";Part 2:"Profile Specific Test Specification (PSTS) Portable radio Termination (PT)";Part 3:"Profile Specific Test Specification (PSTS) Fixed radio Termination (FT)".Transposition datesDate of adoption of this ETS:16 August 1996Date of latest announcement of this ETS (doa):30 November 1996Date of latest publication of new National Standardor endorsement of this ETS (dop/e):31 May 1997Date of withdrawal of any conflicting National Standard (dow):31 May 1997SIST ETS 300 494-3:1999



Page 8ETS 300 494-3: August 1996Blank pageSIST ETS 300 494-3:1999



Page 9ETS 300 494-3: August 19961ScopeThis European Telecommunication Standard (ETS) contains the test specification for Digital EnhancedCordless Telecommunications (DECT) Generic Access Profile (GAP) Fixed Part (FP) applications.The main objective of the GAP test specification is to provide approval tests giving a high probability of airinterface inter-operability between different manufacturer's equipment in different environments (i.e.public, business and residential).The ISO standard for the methodology of conformance testing ISO/IES 9646 Parts 1 to 7 [9] to [15] isused as the basis for the test methodology, and as the basis for test case specification. This is consideredas unsuitable for PH layer testing instead verbal description is used.The test cases listed in this ETS have been derived from the ETS 300 497-1 [18]. In addition as far asPhysical layer is concerned I-ETS 300 176 [16] applies. Additional GAP specific test cases are includedwhere required. The Profile IXIT is based on the DECT CI PIXITs specified in ETS 300 497-1 [18].2Normative referencesThis ETS incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to, or revisions of, any of these publicationsapply to this Technical Basis for Regulation only when incorporated in it by amendment or revision. Forundated references the latest edition of the publication referred to applies.[1]ETS 300 175-1: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 1:Overview".[2]ETS 300 175-2: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 2: PhysicalLayer".[3]ETS 300 175-3: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 3: MediumAccess Control (MAC) layer".[4]ETS 300 175-4: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 4: DataLink Control (DLC) layer".[5]ETS 300 175-5: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 5: Network(NWK) layer".[6]ETS 300 175-6: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 6:Identities and addressing".[7]ETS 300 175-7: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Common Interface (CI); Part 7: Securityfeatures".[8]ETS 300 444 (1995): "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Generic Access Profile (GAP)”.[9]ISO/IEC 9646-1 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 1:General concepts". (See also CCITT Recommendation X.290 (1991)).SIST ETS 300 494-3:1999



Page 10ETS 300 494-3: August 1996[10]ISO/IEC 9646-2 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 2:Abstract test suite specification". (See also CCITT Recommendation X.291(1991)).[11]ISO/IEC 9646-3 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 3:The tree and tabular combined notation". (See also CCITT RecommendationX.292 (1992)).[12]ISO/IEC 9646-4 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 4:Test realisation". (See also CCITT Recommendation X.292 (1992)).[13]ISO/IEC 9646-5 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 5:Requirements on test laboratories and clients for the conformance assessmentprocess". (See also CCITT Recommendation X.292 (1992)).[14]ISO/IEC 9646-6 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 6:Protocol profile test specification".[15]ISO/IEC 9646-7 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 7:Implementation conformance statement".[16]I-ETS 300 176: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Approval test specification".[17]ETS 300 476-1: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI); ProtocolImplementation Conformance Statement (PICS) proforma; Part 1: Network(NWK) layer - Portable radio Termination (PT)".[18]ETS 300 497-1: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) forMedium Access Control (MAC) layer".[19]ETS 300 497-2: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control(MAC) layer - Portable radio Termination (PT)".[20]ETS 300 497-3: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 3: Abstract Test Suite (ATS) for Medium Access Control(MAC) layer - Fixed radio Termination (FT)".[21]ETS 300 497-4: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - DataLink Control (DLC) layer".[22]ETS 300 497-5: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC)layer".SIST ETS 300 494-3:1999



Page 11ETS 300 494-3: August 1996[23]ETS 300 497-6: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 6: Test Suite Structure (TSS) and Test Purposes (TP) -Network (NWK) layer - Portable radio Termination (PT)".[24]ETS 300 497-7: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 7: Abstract Test Suite (ATS) for Network (NWK) layer -Portable radio Termination (PT)".[25]ETS 300 497-8: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 8: Test Suite Structure (TSS) and Test Purposes (TP) -Network (NWK) layer - Fixed radio Termination (FT)".[26]ETS 300 497-9: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI) Test CaseLibrary (TCL); Part 9: Abstract Test Suite (ATS) for Network (NWK) layer - Fixedradio Termination (FT)".[27]ETS 300 474-1: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Generic Access Profile (GAP); Profilerequirement list and profile specific Implementation Conformance Statement(ICS) proforma; Part 1: Portable radio Termination (PT)".[28]ETS 300 494-1: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Generic Access Profile (GAP); ProfileTest Specification (PTS); Part 1: Summary".SIST ETS 300 494-3:1999



Page 12ETS 300 494-3: August 19963Definitions and abbreviations3.1DefinitionsFor the purposes of this ETS, the following definitions apply:-terms defined in ISO/IEC 9646 Parts 1 to 7 [9] to [15];-definitions in ETS 300 175 Parts 1 to 7 [1] to [7];-definitions in ETS 300 444 [8].3.2AbbreviationsFor the purposes of this ETS, the following abbreviations apply:ACAuthentication CodeATSAbstract Test SuiteCCCall ControlCICommon InterfaceDCKDerived Cipher KeyDLCData Link ControlFTFixed radio TerminationGAPGeneric Access ProfileICSImplementation Conformance StatementIPUIInternational Portable User IdentityIUTImplementation Under TestIXITImplementation eXtra Information for TestingLCELink Control EntityLLMELower Layer Management EntityLLNLogical Link NumberMACMedium Access ControlMMMobility ManagementNLFNew Link FlagNWKNetworkPARKPortable Access Rights KeyPHPhysicalPICSProtocol Implementation Conformance StatementPIXITProtocol Implementation eXtra Information for TestingPTPortable radio TerminationPSTSProfile Specific Test SpecificationPTSProfile Test SpecificationSARISecondary Access Rights IdentitySUTSystem Under TestTPUITemporary Portable User IdentityTSTest SystemTSS&TPTest Suite Structure & Test PurposesSIST ETS 300 494-3:1999



Page 13ETS 300 494-3: August 19964Relevant test cases list4.1Network (NWK) layerThis subclause includes lists of the test groups and abstract test cases relevant for GAP PTS - NWK layerFixed Termination (FT) derived from ETS 300 497-9 [26].The page number referenced is the relative page number in the corresponding ETS where the particularitem can be found.NOTE:As ETS 300 497-1 [18] is draft, and some changes are likely due to the results of thePublic Enquiry (PE) phase, page numbers reflecting the exact place in that ETS wherea test case is to be found are not included in this ETS. They shall be added in a laterstage. References when necessary shall be made based on the particular test casename unique through all test specification ETS 300 497-1 [18].4.1.1Test suite structureTable 1Test Suite StructureSuite Name:nwk_ftStandards Ref:ETS 300 444 [8]; ETS 300 497-9 [26]Profile ICS Ref:ETS 300 474 [27]Profile IXIT Ref:ETS 300 494-3Test Method:remoteComments:Test Group ReferenceTest Group ObjectiveFT/To check the behaviour of the NWK layer of the FT(IUT)FT/CC/To check the IUT CC-state machine behaviourFT/CC/IT/To check that the IUT CC-state machine provides sufficient conformance forpossible interconnection without trying to perform thorough testingFT/CC/CA/Limited testing that the observable capabilities of the CC entity of the IUT are inaccordance with the static conformance requirements and the additionalcapabilities claimed in the PROFILE ICS/PROFILE IXITFT/CC/BV/To tests the CC entity of the IUT in response to syntactically and contextualcorrect behaviour of the test systemFT/CC/BV/OC/To check the IUT's behaviours to setup an outgoing callFT/CC/BV/IC/To check the IUT's behaviours to setup an incoming callFT/CC/BV/CI/To check the IUT's behaviour in information transfer proceduresFT/CC/BV/CR/To check the IUT's behaviours to release an outgoing/incoming callFT/CC/BO/To check the behaviour of the CC entity of the IUT in response to the messagesthat are syntactically correct but not allowed to occur in some states of the CCproceduresFT/CC/BI/To check the behaviour of the CC entity of the IUT in response to invalidmessagesFT/CC/TI/To verify that the IUT CC timers are with correct values and the IUT is reactingproperly to the expiry of a timerFT/MM/To check the behaviour of the Mobility Management entity of the IUTFT/MM/IT/To check that the MM entity of the IUT provides sufficient conformance forpossible interconnection without trying to perform thorough testingFT/MM/CA/Limited testing
...

SLOVENSKI STANDARD
SIST ETS 300 494-3:1999
01-maj-1999
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH'(&73URILOJHQHULþQHJD
GRVWRSD*$3GHO2GSURILODRGYLVQDSUHVNXãDOQDVSHFLILNDFLMD3676
ILNVQDUDGLMVND]DNOMXþLWHY)7
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP);
Profile Test Specification (PTS); Part 3: Profile Specific Test Specification (PSTS) - Fixed
radio Termination (FT)
Ta slovenski standard je istoveten z: ETS 300 494-3 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
SIST ETS 300 494-3:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ETS 300 494-3:1999

---------------------- Page: 2 ----------------------

SIST ETS 300 494-3:1999
EUROPEAN ETS 300 494-3
TELECOMMUNICATION August 1996
STANDARD
Source: ETSI TC-RES Reference: DE/RES-03040-3
ICS: 33.020, 33.060.50
Key words: DECT, GAP, testing
Radio Equipment and Systems (RES);
Digital Enhanced Cordless Telecommunications (DECT);
Generic Access Profile (GAP);
Profile Test Specification (PTS);
Part 3: Profile Specific Test Specification (PSTS)
- Fixed radio Termination (FT)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: [e-mail]
Tel.: [phone] - Fax: [phone]
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1996. All rights reserved.

---------------------- Page: 3 ----------------------

SIST ETS 300 494-3:1999
Page 2
ETS 300 494-3: August 1996
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST ETS 300 494-3:1999
Page 3
ETS 300 494-3: August 1996
Contents
Foreword .7
1 Scope .9
2 Normative references.9
3 Definitions and abbreviations .12
3.1 Definitions .12
3.2 Abbreviations .12
4 Relevant test cases list.13
4.1 Network (NWK) layer.13
4.1.1 Test suite structure.13
4.1.2 Test case index .15
4.2 Data Link Control (DLC) layer.19
4.2.1 Test suite structure.19
4.2.2 Test case index .20
4.3 Medium Access Control (MAC) layer.21
4.3.1 Test suite structure.22
4.3.2 Test case index .24
4.4 Physical (PH) layer.25
4.4.1 Manufacturer declarations.25
4.4.2 Normal Transmitted Power (NTP).25
4.4.2.1 Verdict criteria for IUTs with an integral antenna.25
4.4.2.2 Verdict criteria for IUTs with external antenna
connection(s) .25
4.4.3 RFP radio receiver sensitivity.25
4.4.4 Radio receiver interference performance.26
4.4.5 Receiver intermodulation performance .26
5 Additional test cases list.26
5.1 Test purposes .26
5.1.1 NWK layer .26
5.1.2 DLC layer.26
5.1.3 MAC layer.26
5.1.4 PH layer.26
5.2 Test cases .26
5.2.1 NWK layer .26
5.2.2 DLC layer.26
5.2.3 MAC layer.27
5.2.4 PH layer.27
5.2.4.1 Receiver sensitivity tolerance of transmitter deviation
variations .27
5.2.4.1.1 Definition.27
5.2.4.1.2 Test environment.27
5.2.4.1.3 Method of measurement.27
5.2.4.1.4 Verdict criteria.28
5.2.4.2 Transmission of Z-field .28
5.2.4.2.1 Definition.28
5.2.4.2.2 Test environment.28
5.2.4.2.3 Method of measurement.28
5.2.4.2.4 Verdict criteria.28

---------------------- Page: 5 ----------------------

SIST ETS 300 494-3:1999
Page 4
ETS 300 494-3: August 1996
Annex A (normative): Profile Implementation eXtra Information for Testing (IXIT) proforma . 29
A.1 General. 29
A.2 Profile IXIT Requirements List (XRL) . 29
A.2.1 NWK layer protocol . 29
A.2.1.1 Addresses. 29
A.2.1.2 Parameter values. 29
A.2.1.3 Timer values . 29
A.2.1.4 Counters values. 29
A.2.1.5 Protocol constants values. 30
A.2.1.6 Control of Protocol Data Units (PDU) sending. 30
A.2.2 DLC layer protocol. 30
A.2.2.1 Addresses. 30
A.2.2.2 Parameter values. 30
A.2.2.3 Timer values . 30
A.2.2.4 Counters values. 30
A.2.2.5 Protocol constants values. 31
A.2.2.6 Control of PDU sending. 31
A.2.3 MAC layer protocol. 31
A.2.3.1 Addresses. 31
A.2.3.2 Parameter values. 31
A.2.3.3 Timer values . 31
A.2.3.4 Counters values. 31
A.2.3.5 Protocol constants values. 31
A.2.3.6 Control of PDU sending. 32
A.2.4 PH layer protocol. 32
A.2.4.1 Addresses. 32
A.2.4.2 Parameter values. 32
A.2.4.3 Timer values . 32
A.2.4.4 Counters values. 32
A.2.4.5 Protocol constants values. 32
A.2.4.6 Control of PDU sending. 32
A.3 Profile specific IXIT. 32
A.3.1 NWK layer . 32
A.3.2 DLC layer . 32
A.3.3 MAC layer. 33
A.3.4 PH layer. 33
A.3.5 Configuration constraints . 33
Annex B (normative): Profile Conformance Test Report (PCTR) proforma . 34
B.1 Identification summary. 34
B.1.1 PCTR. 34
B.1.2 Implementation Under Test (IUT) . 35
B.1.3 Testing environment. 35
B.1.4 Limits and reservations . 35
B.1.5 Comments. 36
B.2 IUT conformance status . 36
B.3 Static conformance summary. 36
B.4 Dynamic conformance summary. 36
B.5 Static conformance review report . 37

---------------------- Page: 6 ----------------------

SIST ETS 300 494-3:1999
Page 5
ETS 300 494-3: August 1996
B.6 Test campaign report .37
B.6.1 NWK layer.38
B.6.2 DLC layer .40
B.6.3 MAC layer .41
B.6.4 PH layer .41
B.7 Observations .42
Annex C (normative): System Conformance Test Report (SCTR) proforma .43
C.1 Identification summary .43
C.1.1 SCTR .43
C.1.2 Test laboratory.43
C.1.3 Client.44
C.1.4 System Under Test (SUT) .44
C.1.5 Profile.44
C.1.6 Nature of conformance testing.45
C.1.7 Limits and reservations.45
C.1.8 Record of agreement.45
C.1.9 Comments .45
C.2 System report summary .46
C.2.1 Profile testing summary for GAP NWK layer FT.46
C.2.2 Profile testing summary for GAP DLC layer FT.47
C.2.3 Profile testing summary for GAP MAC layer FT .48
C.2.4 Profile testing summary for GAP PH layer FT .49
Annex D (normative): System Conformance Statement (SCS) proforma.50
D.1 Identification summary .50
D.1.1 SCS identification.50
D.1.2 IUT identification .50
D.1.3 Client identification.50
D.1.4 Supplier identification.51
D.1.5 Manufacturer identification.52
D.1.6 Protocols identification.52
D.1.7 Profile identification.52
D.2 Miscellaneous System Information .52
D.2.1 Configuration.52
D.2.2 Other information .53
History.54

---------------------- Page: 7 ----------------------

SIST ETS 300 494-3:1999
Page 6
ETS 300 494-3: August 1996
Blank page

---------------------- Page: 8 ----------------------

SIST ETS 300 494-3:1999
Page 7
ETS 300 494-3: August 1996
Foreword
This European Telecommunication Standard (ETS) has been produced by the Radio Equipment and
Systems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).
The General Access Profile (GAP) Profile Test Specification (PTS) comprises three parts:
Part 1: "Summary";
Part 2: "Profile Specific Test Specification (PSTS) Portable radio Termination (PT)";
Part 3: "Profile Specific Test Specification (PSTS) Fixed radio Termination (FT)".
Transposition dates
Date of adoption of this ETS: 16 August 1996
Date of latest announcement of this ETS (doa): 30 November 1996
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 May 1997
Date of withdrawal of any conflicting National Standard (dow): 31 May 1997

---------------------- Page: 9 ----------------------

SIST ETS 300 494-3:1999
Page 8
ETS 300 494-3: August 1996
Blank page

---------------------- Page: 10 ----------------------

SIST ETS 300 494-3:1999
Page 9
ETS 300 494-3: August 1996
1 Scope
This European Telecommunication Standard (ETS) contains the test specification for Digital Enhanced
Cordless Telecommunications (DECT) Generic Access Profile (GAP) Fixed Part (FP) applications.
The main objective of the GAP test specification is to provide approval tests giving a high probability of air
interface inter-operability between different manufacturer's equipment in different environments (i.e.
public, business and residential).
The ISO standard for the methodology of conformance testing ISO/IES 9646 Parts 1 to 7 [9] to [15] is
used as the basis for the test methodology, and as the basis for test case specification. This is considered
as unsuitable for PH layer testing instead verbal description is used.
The test cases listed in this ETS have been derived from the ETS 300 497-1 [18]. In addition as far as
Physical layer is concerned I-ETS 300 176 [16] applies. Additional GAP specific test cases are included
where required. The Profile IXIT is based on the DECT CI PIXITs specified in ETS 300 497-1 [18].
2 Normative references
This ETS incorporates, by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to, or revisions of, any of these publications
apply to this Technical Basis for Regulation only when incorporated in it by amendment or revision. For
undated references the latest edition of the publication referred to applies.
[1] ETS 300 175-1: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 1:
Overview".
[2] ETS 300 175-2: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical
Layer".
[3] ETS 300 175-3: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 3: Medium
Access Control (MAC) layer".
[4] ETS 300 175-4: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 4: Data
Link Control (DLC) layer".
[5] ETS 300 175-5: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 5: Network
(NWK) layer".
[6] ETS 300 175-6: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 6:
Identities and addressing".
[7] ETS 300 175-7: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Common Interface (CI); Part 7: Security
features".
[8] ETS 300 444 (1995): "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Generic Access Profile (GAP)”.
[9] ISO/IEC 9646-1 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 1:
General concepts". (See also CCITT Recommendation X.290 (1991)).

---------------------- Page: 11 ----------------------

SIST ETS 300 494-3:1999
Page 10
ETS 300 494-3: August 1996
[10] ISO/IEC 9646-2 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 2:
Abstract test suite specification". (See also CCITT Recommendation X.291
(1991)).
[11] ISO/IEC 9646-3 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 3:
The tree and tabular combined notation". (See also CCITT Recommendation
X.292 (1992)).
[12] ISO/IEC 9646-4 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 4:
Test realisation". (See also CCITT Recommendation X.292 (1992)).
[13] ISO/IEC 9646-5 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 5:
Requirements on test laboratories and clients for the conformance assessment
process". (See also CCITT Recommendation X.292 (1992)).
[14] ISO/IEC 9646-6 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 6:
Protocol profile test specification".
[15] ISO/IEC 9646-7 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 7:
Implementation conformance statement".
[16] I-ETS 300 176: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Approval test specification".
[17] ETS 300 476-1: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI); Protocol
Implementation Conformance Statement (PICS) proforma; Part 1: Network
(NWK) layer - Portable radio Termination (PT)".
[18] ETS 300 497-1: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) for
Medium Access Control (MAC) layer".
[19] ETS 300 497-2: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control
(MAC) layer - Portable radio Termination (PT)".
[20] ETS 300 497-3: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 3: Abstract Test Suite (ATS) for Medium Access Control
(MAC) layer - Fixed radio Termination (FT)".
[21] ETS 300 497-4: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - Data
Link Control (DLC) layer".
[22] ETS 300 497-5: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC)
layer".

---------------------- Page: 12 ----------------------

SIST ETS 300 494-3:1999
Page 11
ETS 300 494-3: August 1996
[23] ETS 300 497-6: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 6: Test Suite Structure (TSS) and Test Purposes (TP) -
Network (NWK) layer - Portable radio Termination (PT)".
[24] ETS 300 497-7: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 7: Abstract Test Suite (ATS) for Network (NWK) layer -
Portable radio Termination (PT)".
[25] ETS 300 497-8: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 8: Test Suite Structure (TSS) and Test Purposes (TP) -
Network (NWK) layer - Fixed radio Termination (FT)".
[26] ETS 300 497-9: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI) Test Case
Library (TCL); Part 9: Abstract Test Suite (ATS) for Network (NWK) layer - Fixed
radio Termination (FT)".
[27] ETS 300 474-1: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile
requirement list and profile specific Implementation Conformance Statement
(ICS) proforma; Part 1: Portable radio Termination (PT)".
[28] ETS 300 494-1: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile
Test Specification (PTS); Part 1: Summary".

---------------------- Page: 13 ----------------------

SIST ETS 300 494-3:1999
Page 12
ETS 300 494-3: August 1996
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this ETS, the following definitions apply:
- terms defined in ISO/IEC 9646 Parts 1 to 7 [9] to [15];
- definitions in ETS 300 175 Parts 1 to 7 [1] to [7];
- definitions in ETS 300 444 [8].
3.2 Abbreviations
For the purposes of this ETS, the following abbreviations apply:
AC Authentication Code
ATS Abstract Test Suite
CC Call Control
CI Common Interface
DCK Derived Cipher Key
DLC Data Link Control
FT Fixed radio Termination
GAP Generic Access Profile
ICS Implementation Conformance Statement
IPUI International Portable User Identity
IUT Implementation Under Test
IXIT Implementation eXtra Information for Testing
LCE Link Control Entity
LLME Lower Layer Management Entity
LLN Logical Link Number
MAC Medium Access Control
MM Mobility Management
NLF New Link Flag
NWK Network
PARK Portable Access Rights Key
PH Physical
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
PT Portable radio Termination
PSTS Profile Specific Test Specification
PTS Profile Test Specification
SARI Secondary Access Rights Identity
SUT System Under Test
TPUI Temporary Portable User Identity
TS Test System
TSS&TP Test Suite Structure & Test Purposes

---------------------- Page: 14 ----------------------

SIST ETS 300 494-3:1999
Page 13
ETS 300 494-3: August 1996
4 Relevant test cases list
4.1 Network (NWK) layer
This subclause includes lists of the test groups and abstract test cases relevant for GAP PTS - NWK layer
Fixed Termination (FT) derived from ETS 300 497-9 [26].
The page number referenced is the relative page number in the corresponding ETS where the particular
item can be found.
NOTE: As ETS 300 497-1 [18] is draft, and some changes are likely due to the results of the
Public Enquiry (PE) phase, page numbers reflecting the exact place in that ETS where
a test case is to be found are not included in this ETS. They shall be added in a later
stage. References when necessary shall be made based on the particular test case
name unique through all test specification ETS 300 497-1 [18].
4.1.1 Test su
...