ETSI ETS 300 017 ed.1 (1994-09)

Terminal Equipment (TE); Test procedures for Teletex

T/TE 07-05

Terminalska oprema (TE) – Preskusni postopki za sistem Teletex

General Information

• Status: Published
• Publication Date: 06-Sep-1994
• Technical Committee: TE 2 - Telematics: Facsimile, Document Handling and Transfer
• Current Stage: 12 - Completion
• Due Date: 23-Aug-1994
• Completion Date: 07-Sep-1994
• Ref Project: SIST ETS 300 017 E1:2003 - Terminal Equipment (TE); Test procedures for Teletex

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ETS 300 017 E1:2003
01-december-2003
Terminalska oprema (TE) – Preskusni postopki za sistem Teletex
Terminal Equipment (TE); Test procedures for Teletex
Ta slovenski standard je istoveten z: ETS 300 017 Edition 1
ICS:
33.050.30 Oprema za teleks, teletekst, Equipment for telex, teletext,
telefaks telefax
SIST ETS 300 017 E1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ETS 300 017 E1:2003

---------------------- Page: 2 ----------------------

SIST ETS 300 017 E1:2003
EUROPEAN ETS 300 017
TELECOMMUNICATION September 1994
STANDARD
Source: ETSI TC-TE Reference: T/TE 07-05
ICS: 33.020, 33.040.40
Teletex
Key words:
Terminal Equipment (TE);
Test procedures for Teletex
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
F-06921 Sophia Antipolis CEDEX - FRANCE
Postal address:
650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Office address:
c=fr, a=atlas, p=etsi, s=secretariat - [e-mail]
X.400: Internet:
Tel.: [phone] - Fax: [phone]
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1994. All rights reserved.
New presentation - see History box

---------------------- Page: 3 ----------------------

SIST ETS 300 017 E1:2003
Page 2
ETS 300 017: September 1994
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST ETS 300 017 E1:2003
Page 3
ETS 300 017: September 1994
Contents
Foreword.7
1 Scope .9
2 Normative references . 10
3 Definitions and abbreviations. 11
3.1 Definitions. 11
3.2 Abbreviations. 11
4 Test limitations. 11
5 Structure of the recommendation. 11
Annex A (normative): Transport layer ("C"). 13
Annex B (normative): Transport layer ("N") . 14
Annex C (normative): Additional tests for T.62 ETSI requirements, see ETS 300 015 ("C") . 16
Annex D (normative): Additional tests for T.62, national requirements ("N") . 23
Annex E (normative): Additional tests for service and terminal requirements, ETSI requirement ("C") 24
Annex F (normative): Additional tests for service and terminal requirements, national requirements. 29
Annex G (normative): Teletex test documents - ETSI requirements ("C"). 39
G.1 Introduction. 39
G.1.1 General. 39
G.1.2 Mandatory tests of ITU-T Recommendation T.64. 39
G.1.2.1 SUT calling, tester called . 39
G.1.2.2 SUT called, tester calling . 39
G.1.3 Conditional tests ITU-T Recommendation T.64 . 40
G.1.3.1 SUT calling, tester called . 40
G.1.3.2 SUT called, tester calling . 40
G.1.4 Exception conditions (ITU-T Recommendation T.64) . 41
G.1.4.1 SUT calling, tester called . 41
G.1.4.2 SUT called, tester calling . 41
G.1.5 Additional ETSI tests (Annex E of this ETS) . 41
G.2 Index of documents . 41
G.3 Test document presentation . 43
G.4 Test document encoding . 107
Annex H (informative): Teletex test texts, national requirements ("N") . 245
Annex J (normative): Test procedures for data link layer in CSPDN, ETSI requirements ("C") . 246
J.1 General . 246
J.1.1 Introduction. 246
J.1.2 Description . 246

---------------------- Page: 5 ----------------------

SIST ETS 300 017 E1:2003
Page 4
ETS 300 017: September 1994
J.2 States and functions . 246
J.3 Description of the sequences. 247
J.3.1 Explanation of the table description. 247
J.3.2 List of abbreviations . 248
J.4 Test description tables. 249
J.5 Description of the states and tests. 295
J.5.1 Disconnected state. 296
J.5.2 Disconnect request state . 297
J.5.3 Connected state. 298
J.5.4 Established state. 299
J.5.4.1 Established-reject. 299
J.5.4.2 Established-blocked. 300
J.5.4.3 Established-FRMR . 301
J.5.4.4 Established-normal. 302
J.5.5 Exchange procedure state . 303
J.5.6 Identification procedure state . 305
J.5.7 Window rotation state. 306
J.5.8 Connection request state . 307
J.5.9 DTE clear request state. 309
J.5.10 DXE clear indication state . 311
J.5.11 Flow control ready state . 313
J.5.12 DTE reset request state . 315
J.5.13 DXE reset indication state. 317
J.5.14 DXE receive ready state. 318
J.5.15 DXE receive not ready state . 319
J.5.16 DTE receive ready state . 320
J.5.17 Window filling and rotation state . 322
J.5.18 Timer tests . 323
J.5.19 Address tests . 324
J.5.20 Facility tests . 325
J.6 Basic Interconnection Tests (BITs) . 327
Annex K (informative): Test procedures for the data link layer in CSPDN, National requirements ("N")337
Annex L (informative): Test procedures for the network layer in CSPDN, ETSI requirements ("C") . 338
L.1 General . 338
L.1.1 Introduction. 338
L.1.2 Description . 338
L.2 Test schedules for the CSPN case. 339
Annex M (normative): Test procedures for the network layer in CSPDN, National requirements ("N")343
M.1 General . 343
M.1.1 Introduction. 343
M.1.2 Description . 343
M.2 Test schedule for CSPDN . 343
Annex N (informative): Test procedures for the data link in PSTN, ETSI requirements ("C"). 346
N.1 Test for X.25 protocol, layer 2, on PSTN network for teletex service . 346
Annex P (informative): Test procedures for the network layer in PSTN, national requirements ("N") . 347

---------------------- Page: 6 ----------------------

SIST ETS 300 017 E1:2003
Page 5
ETS 300 017: September 1994
Annex Q (normative): Teletex Protocol Implementation Conformance Statement (PICS). 347
Q.1 Abbreviations. 347
Q.2 Introduction. 348
Q.2.1 Product PICS. 348
Q.2.2 Protocol Implementation Conformance Statement (PICS). 348
Q.3 Instructions for completion . 349
Q.3.1 Instructions for the completion of the Product PICS . 349
Q.3.2 Instructions for completion of the PICS proforma. 350
Q.3.2.1 Proforma tables . 350
Q.3.2.2 Completion of tables. 351
Q.4 Product PICS. 352
Q.5 Link Layer PICS. 354
Q.5.1 Supported functions. 354
Q.5.2 Supported PDUs . 355
Q.5.3 Initiator/responder capability . 363
Q.5.4 Timers. 363
Q.5.5 Procedures and reactions to protocol errors. 363
Q.5.6 Counters . 364
Q.6 Network layer PICS. 365
Q.6.1 Supported functions. 365
Q.6.2 Supported PDUs . 365
Q.6.3 Initiator/responder capability . 365
Q.6.4 Particular protocol procedures . 365
Q.7 Transport layer PICS. 366
Q.7.1 Supported Functions. 366
Q.7.2 Supported TPDUs . 368
Q.7.3 Initiator/responder capabilities. 368
Q.7.4 Negotiation . 369
Q.7.5 Timers. 369
Q.7.6 Procedures and reactions to protocol errors. 370
Q.8 Session/document layer PICS . 372
Q.8.1 Supported functions. 372
Q.8.2 Supported PDUs . 373
Q.8.3 Initiator/responder capabilities. 375
Q.8.4 Negotiation . 375
Q.8.5 Timers. 377
Q.8.6 Procedures to Reactions to Protocol Errors . 378
Q.8.7 Particular protocol procedures . 380
Q.9 Application layer PICS. 383
Q.9.1 Supported functions. 383
Q.9.1.1 Calling side. 383
Q.9.1.2 Called Side. 384
Q.9.2 Supported PDUs . 385
Q.9.3 Initiator/responder capabilities. 385
Q.9.4 Negotiation . 385
Q.9.5 Timers. 385
Q.9.6 Procedures and reactions to protocol errors. 386
Q.9.7 Particular protocol procedures . 387
Annex R (normative): Teletex Protocol Implementation eXtra Information for Testing (PIXIT). 388

---------------------- Page: 7 ----------------------

SIST ETS 300 017 E1:2003
Page 6
ETS 300 017: September 1994
R.1 Abbreviations . 388
R.2 Introduction. 388
R.3 Test laboratory information proforma . 389
R.4 Client organisation information proforma. 390
R.5 Testing environment. 391
R.5.1 Machine configuration. 391
R.5.2 Operating system. 391
R.5.3 Ancillary layers. 391
R.6 Link layer PIXIT (CSDN) . 392
R.7 Network layer PIXIT (CSDN). 393
R.8 Transport Layer PIXIT. 394
R.9 Session/Document PIXIT . 395
R.10 Application layer PIXIT. 398
Annex S (normative): Cross reference list between Teletex PICS and test cases. 399
S.1 Introduction. 399
S.2 Cross references between PICS and test cases. 400
S.2.1 Link layer (CSDN) . 400
S.2.2 Network layer (CSDN). 400
S.2.3 Transport layer . 401
S.2.4 Session/Document layer . 402
S.2.5 Application layer. 405
Annex T (normative): Test report proforma. 406
History . 417

---------------------- Page: 8 ----------------------

SIST ETS 300 017 E1:2003
Page 7
ETS 300 017: September 1994
Foreword
This European Telecommunication Standard (ETS) was produced by the Terminal Equipment (TE)
Technical Committee of the European Telecommunications Standards Institute (ETSI).
This ETS contains the ETSI agreed and national tests. It is based on, and aligns with, the requirements for
basic Teletex equipment given in the following ETS and ETR:
- ETS 300 015 (1994): "Terminal Equipment (TE); Basic and recommended additional requirements
for terminal equipment supporting Teletex application" [11];
- ETR 052 (1993): "Terminal Equipment (TE); Service intercommunication requirements for Teletex
terminal equipment".
This ETS does not replace CEPT Recommendation T/TE 07-02 (1988), reflecting the current situation for
type approval and certification, and which co-exists with this ETS until it is adopted by ETSI as a full ETS.
Transposition dates
Date of latest announcement of this ETS (doa): 30 November 1994
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 May 1995
Date of withdrawal of any conflicting National Standard (dow): 31 May 1995

---------------------- Page: 9 ----------------------

SIST ETS 300 017 E1:2003
Page 8
ETS 300 017: September 1994
Blank page

---------------------- Page: 10 ----------------------

SIST ETS 300 017 E1:2003
Page 9
ETS 300 017: September 1994
1 Scope
This ETS contains and refers to test procedures to facilitate member bodies verification of the protocol and
service conformance of Teletex systems in order to ensure the international compatibility of Teletex.
Furthermore, the specific Teletex service and protocol definitions of ETSI are considered to harmonise the
test procedures for those requirements.
This ETS contains the ETSI agreed test cases which may be used by the ETSI member countries. It also
contains national test requirements.
This ETS is only applicable when considered together with ITU-T Recommendation T.64 [5]. The test
definitions for the related CCITT Recommendations, which define the Teletex service, are not duplicated in
this ETS.
The ETSI and national test procedures contained herein are based on requirements for Teletex systems in
three main areas:
a) conformance testing procedures for Teletex defined in ITU-T Recommendation T.64 [5];
b) characteristics of Teletex equipments, specified in ETS 300 015 [11];
c) characteristics of Teletex equipments for Circuit Switched Public Data Networks (CSPDN) and
Public Switched Data Networks (PSTN) for layers 2 and 3, specified in ITU-T Recommendation
T 70 [6].
Therefore, the test procedures of this ETS cover all ETSI aspects of Teletex which have end-to-end
significance. Thus, tests for the network dependent layers (layers 2 and 3) of CSPDN and PSTN are
included.
These test procedures do not supersede the relevant CCITT, ITU-T and ETSI standards which continue to
be the definitive specifications for all aspects of the Teletex service.
The test procedures of this ETS, together with the test procedures in ITU-T, are intended to assist
verification and cannot fully guarantee the compliance of Teletex systems to the relevant
Recommendations and Standards.
The whole of ITU-T Recommendation T.64 [5] together with this ETS should be applied for a
comprehensive test of a Teletex system.
This ETS refers to ETS 300 015 [11] which is the basis for the European Teletex terminal equipment
specification.
This ETS reflects the definitions ETS 300 015 [11] as far as those requirements are testable or considered
for testing.
Since the interworking with telex service became optional in CCITT Recommendation F.200 [9] and ITU-T
Recommendation T.60 [1], all the tests related to the Teletex/telex interworking are also optional. Only in
the case where the terminal provider declares the terminal supports this option do the tests become
mandatory.

---------------------- Page: 11 ----------------------

SIST ETS 300 017 E1:2003
Page 10
ETS 300 017: September 1994
2 Normative references
This ETS incorporates by dated or undated reference, provisions from other publications. These normative
references are cited at the appropriate places in the text and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this ETS
only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies.
[1] ITU-T Recommendation T.60 (1993): "Terminal equipment for use in the teletex
service".
[2] ITU-T Recommendation T.61 (1993): "Character repertoire and coded character
sets for the international teletex service".
[3] ITU-T Recommendation T.62 (1993): "Control procedures for teletex and Group
4 facsimile services".
[4] CCITT Recommendation T.63 (1988): "Provisions for verification of teletex
terminal compliance".
[5] ITU-T Recommendation T.64 (1993): "Conformance testing procedures for the
teletex Recommendations".
[6] ITU-T Recommendation T.70 (1993): "Network-independent basic transport
service for the telematic services".
[7] CCITT Recommendation T.90 (1992): "Characteristics and protocols for
telematic services in ISDN".
[8] CCITT Recommendation T.390 (1988): "Teletex requirements for interworking
with the telex service".
[9] CCITT Recommendation F.200 (1992): "Teletex service".
[10] ITU-T Recommendation F.201: "Interworking between teletex service and telex
service - General principles".
[11] ETS 300 015 (1994): "Terminal Equipment (TE); Basic and additional
requirements for terminal equipment supporting teletex application".
[12] ETS 300 081 (1993): "Integrated Services Digital Network (ISDN); Teletex end-
to-end protocol over the ISDN".
[13] ETS 300 154 (1994): "Terminal Equipment (TE); Terminal characteristics for the
telematic file transfer within the teletex service [ITU-T Recommendation T.571
(modified)]".
[14] Draft prETS 300 243-1: "Terminal Equipment (TE); Programmable
Communication Interface (PCI) APPLI/COM for facsimile group 3, facsimile
group 4, teletex and telex services, Part 1: CCITT Recommendation T.611
(1992) [modified]".
[15] ENV 41104 (1987): "Packet-switched data networks; Permanent access (FS
T/31)".
[16] ENV 41106 (1988): "Digital data circuit (circuit switched data networks);
Provision of the OSI connection-mode transport service in the T.70 case for
Telematic end systems (FS T/41)".

---------------------- Page: 12 ----------------------

SIST ETS 300 017 E1:2003
Page 11
ETS 300 017: September 1994
[17] ENV 41105 (1988): "Packet-switched data networks; switched access (FS
T/32)".
[18] NET 1: "Approval requirements for data terminal equipment to connect to CSPN
and leased circuits using CCITT Recommendation X.21 interface".
[19] NET 2: "Approval requirements for data terminal equipment to connect to Packet
Switched Public Data Network (PSPDN) using CCITT Recommendation X.25
(1984) interface".
[20] ETS 300 001: "Attachments to the Public Switched Telephone Network (PSTN);
General technical requirements for equipment connected to an analogue
subscriber interface in the PSTN (NET 4)".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this ETS, the terms given are as defined in ITU-T/CCITT Recommendations T.60 [1],
T.61 [2], T.62 [3], T.64 [5], T.70 [6], F.201 [10] and CCITT Recommendations T.63 [4], T.90 [7], T.390 [8]
and F.200 [9].
3.2 Abbreviations
For the purposes of this ETS, the abbreviations given are as defined in the CCITT and ITU-T
Recommendations referenced in subclause 3.1.
4 Test limitations
The tests shall establish, to an acceptable degree of reliability, that a Teletex system conforms to the
relevant Recommendations and Standards. It shall not be possible to test for complete conformance due
to:
a) the immense number of state event combinations and possible valid and invalid PDU types which
would require an unacceptably large amount of computational resources and time;
b) the possibility that previous actions may affect the results of a particular test;
c) "transient" states that, although defined in the Recommendations and Standards, may not be
externally accessible. Therefore, the relevant test cases defined in ITU-T Recommendation T.64 [5]
and denoted by "transient state" may, or may not, be used in the ETSI member countries.
5 Structure of the recommendation
Test procedures
...