ETSI EN 303 980 V1.3.1 (2022-10)
Satellite Earth Stations and Systems (SES); Fixed and in-motion Earth Stations communicating with non-geostationary satellite systems (NEST) in the 11 GHz to 14 GHz frequency bands; Harmonised Standard for access to radio spectrum
Satellite Earth Stations and Systems (SES); Fixed and in-motion Earth Stations communicating with non-geostationary satellite systems (NEST) in the 11 GHz to 14 GHz frequency bands; Harmonised Standard for access to radio spectrum
REN/SES-00460
Satelitske zemeljske postaje in sistemi (SES) - Nepremične in premične zemeljske postaje, ki komunicirajo z negeostacionarnimi satelitskimi sistemi (NEST) v frekvenčnih pasovih od 11 GHz do 14 GHz - Harmonizirani standard za dostop do radijskega spektra
Ta dokument določa tehnične lastnosti in metode merjenja za nepremične in premične zemeljske postaje, ki komunicirajo z negeostacionarnimi satelitskimi sistemi (NEST) v frekvenčnih pasovih fiksnih satelitskih storitev (FSS) od 11 GHz do 14 GHz, z naslednjimi značilnostmi:
• Negeostacionarni satelitski sistem je izdelan za mobilno in stacionarno delovanje.
• Negeostacionarni satelitski sistem deluje na različnih platformah, npr. na vlakih, morskih plovilih, letalih in drugih vozilih, pri čemer lahko pride do občasnih motenj in prekinitev v satelitski povezavi.
• Negeostacionarni satelitski sistem deluje kot del satelitskega sistema, ki se uporablja za zagotavljanje širokopasovne komunikacije.
• Negeostacionarni satelitski sistem zajema vso opremo, električno in mehansko, od same antene do vmesnikov z drugo komunikacijsko opremo na mobilni platformi.
• Negeostacionarni satelitski sistem zajema enega ali več oddajnikov, pri čemer naj bi se pregled sistema na sliki 1 razlagal v skladu s tem.
• Frekvence oddajanja in sprejemanja so prikazane v preglednici 1.
Negeostacionarni satelitski sistem oddaja v frekvenčnem območju od 14,0 GHz do 14,50 GHz. Negeostacionarni satelitski sistem oddaja pod
višinskimi koti 35° ali večjimi glede na obzorje.
• Negeostacionarni satelitski sistem sprejema v območju od 10,70 GHz do 12,75 GHz.
• Negeostacionarni satelitski sistem uporablja linearno ali krožno polarizacijo.
• Negeostacionarni satelitski sistem komunicira z negeostacionarnimi sateliti.
• Negeostacionarni satelitski sistem je izdelan za nenadzorovano delovanje.
• Negeostacionarni satelitski sistem se krmili in nadzira z napravo za krmiljenje omrežja (NCF). Naprava za krmiljenje omrežja ne spada na področje uporabe tega dokumenta.
Ta dokument se uporablja za negeostacionarni satelitski sistem s pomožno opremo in različnimi telekomunikacijskimi vrati, ko ta deluje znotraj mejnih vrednosti obratovalnega okoljskega profila, kot ga določi proizvajalec, ter ko je nameščen v skladu z zahtevami proizvajalčeve izjave ali v skladu z zahtevami dokumentacije uporabnika.
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.6] je podano v dodatku A.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 303 980 V1.3.1:2023
01-januar-2023
Satelitske zemeljske postaje in sistemi (SES) - Nepremične in premične zemeljske
postaje, ki komunicirajo z negeostacionarnimi satelitskimi sistemi (NEST) v
frekvenčnih pasovih od 11 GHz do 14 GHz - Harmonizirani standard za dostop do
radijskega spektra
Satellite Earth Stations and Systems (SES) - Fixed and in-motion Earth Stations
communicating with non-geostationary satellite systems (NEST) in the 11 GHz to 14 GHz
frequency bands - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 980 V1.3.1 (2022-10)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 303 980 V1.3.1:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 980 V1.3.1:2023
---------------------- Page: 2 ----------------------
SIST EN 303 980 V1.3.1:2023
ETSI EN 303 980 V1.3.1 (2022-10)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed and in-motion Earth Stations communicating with
non-geostationary satellite systems (NEST)
in the 11 GHz to 14 GHz frequency bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
SIST EN 303 980 V1.3.1:2023
2 ETSI EN 303 980 V1.3.1 (2022-10)
Reference
REN/SES-00460
Keywords
broadband, earth station, mobile, regulation,
satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 980 V1.3.1:2023
3 ETSI EN 303 980 V1.3.1 (2022-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.0 Objective . 14
4.1.1 Environmental profile . 14
4.1.2 Void . 14
4.1.3 Operating configurations . 14
4.1.4 Presentation of equipment for testing purposes . 14
4.1.5 Choice of model for testing . 15
4.1.6 Operation of multiple NEST on a single frequency . 15
4.2 Conformance requirements . 15
4.2.1 Void . 15
4.2.2 Antenna beam pointing . 15
4.2.2.1 Pointing accuracy . 15
4.2.2.1.1 Purpose . 15
4.2.2.1.2 Antenna Beam Pointing error . 15
4.2.2.2 Pointing error detection . 15
4.2.2.2.1 Purpose . 15
4.2.2.2.2 Pointing error detection specification . 16
4.2.2.3 Conformance tests . 16
4.2.3 Off-axis spurious radiation . 16
4.2.3.1 Justification . 16
4.2.3.2 Specification. 16
4.2.3.3 Conformance tests . 17
4.2.4 On-axis spurious radiation . 17
4.2.4.1 Justification . 17
4.2.4.2 Specification. 17
4.2.4.2.1 "Carrier-on" radio state . 17
4.2.4.2.2 "Carrier-off" and "Emissions disabled" radio states . 18
4.2.4.3 Conformance tests . 18
4.2.5 Carrier suppression . 18
4.2.5.1 Justification . 18
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Cessation of emissions . 18
4.2.6.1 Justification . 18
4.2.6.2 Specification. 18
4.2.6.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.6.2.2 Specification 2: Conditions under which the NEST shall cease emissions . 19
4.2.6.2.3 Specification 3: Cessation of emissions . 19
4.2.6.2.4 Specification 4: Fault conditions . 20
4.2.6.3 Conformance tests . 20
4.2.7 Identification of the NEST and its location . 20
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 980 V1.3.1:2023
4 ETSI EN 303 980 V1.3.1 (2022-10)
4.2.7.1 Justification . 20
4.2.7.2 Specification. 20
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 21
4.2.8.1 General - Finite State Machine Model . 21
4.2.8.2 Processor monitoring . 23
4.2.8.2.1 Justification . 23
4.2.8.2.2 Specification . 23
4.2.8.2.3 Conformance tests . 24
4.2.8.3 Transmit subsystem monitoring . 24
4.2.8.3.1 Justification . 24
4.2.8.3.2 Specification . 24
4.2.8.3.3 Conformance tests . 24
4.2.8.4 Power-on/Reset . 24
4.2.8.4.1 Justification . 24
4.2.8.4.2 Specification . 24
4.2.8.4.3 Conformance tests . 24
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 24
4.2.8.5.1 Justification . 24
4.2.8.5.2 Specification . 25
4.2.8.5.3 Conformance tests . 25
4.2.8.6 Network control commands . 25
4.2.8.6.1 Justification . 25
4.2.8.6.2 Specification . 26
4.2.8.6.3 Conformance tests . 26
4.2.8.7 Initial burst transmission . 26
4.2.8.7.1 Justification . 26
4.2.8.7.2 Specification . 26
4.2.8.7.3 Conformance tests . 26
4.2.8.8 Inhibition of transmissions . 27
4.2.8.8.1 Justification . 27
4.2.8.8.2 Specification . 27
4.2.8.8.3 Conformance tests . 27
4.2.9 Receive antenna off-axis gain pattern . 27
4.2.9.1 Justification . 27
4.2.9.2 Specification. 27
4.2.9.3 Conformance tests . 28
4.2.10 Blocking performance . 28
4.2.10.1 Justification . 28
4.2.10.2 Specification. 28
4.2.10.3 Conformance tests . 28
4.2.11 Adjacent Signal Selectivity . 28
4.2.11.1 Justification . 28
4.2.11.2 Specification. 29
4.2.11.3 Conformance tests . 29
5 Testing for compliance with technical requirements . 29
5.1 Environmental conditions for testing . 29
5.2 Ancillary Equipment . 29
5.3 Nominated Bandwidth . 29
5.4 Essential radio test suites . 29
6 Test methods for all aspects of the NEST . 30
6.1 General . 30
6.1.1 General requirements . 30
6.2 Off-axis spurious radiation . 30
6.2.1 General . 30
6.2.2 Test method . 30
6.2.2.1 General . 30
6.2.2.2 Multi-carrier operation . 31
6.2.3 Measurements up to 1 000 MHz . 31
6.2.3.1 Test site . 31
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 980 V1.3.1:2023
5 ETSI EN 303 980 V1.3.1 (2022-10)
6.2.3.2 Void. 31
6.2.3.3 Procedure . 31
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 32
6.2.4.2.1 Test site. 32
6.2.4.2.2 Procedure . 32
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32
6.2.4.3.1 Test site. 32
6.2.4.3.2 Procedure . 33
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 34
6.2.4.4.1 Test site. 34
6.2.4.4.2 Procedure . 34
6.3 On-axis spurious radiation . 35
6.3.1 Test method . 35
6.3.1.1 General . 35
6.3.1.2 Test site . 35
6.3.1.3 Method of measurement . 35
6.3.1.3.1 General . 35
6.3.1.3.2 Method of measurement at the antenna flange . 35
6.3.1.3.3 Method of measurement for an EUT with antenna . 37
6.4 Void . 38
6.5 Carrier suppression . 38
6.5.1 General . 38
6.5.2 Test method . 38
6.6 Antenna beam pointing . 39
6.6.1 General . 39
6.6.2 Test methods . 39
6.7 Cessation of emissions of the NEST . 40
6.7.1 General . 40
6.7.2 Test Method . 40
6.7.2.1 Required documentation and preparation of the test . 40
6.7.2.2 Cessation of emissions from the "Transmission enabled" state . 40
6.7.2.3 Cessation of emission from the "Transmission disabled" state . 40
6.7.2.4 Cessation of emission from the "Initial Phase" state . 41
6.7.2.4.1 EUTs transmitting initial bursts . 41
6.7.2.4.2 EUTs not transmitting initial bursts . 41
6.7.2.5 "Single action" means of cessation of emissions. 41
6.7.2.6 Fault conditions . 42
6.8 Identification of NEST and location determination . 42
6.8.1 Test arrangement . 42
6.8.2 Test method . 43
6.9 Control and monitoring functions . 43
6.9.1 General .
...
ETSI EN 303 980 V1.3.1 (2022-10)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed and in-motion Earth Stations communicating with
non-geostationary satellite systems (NEST)
in the 11 GHz to 14 GHz frequency bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 ETSI EN 303 980 V1.3.1 (2022-10)
Reference
REN/SES-00460
Keywords
broadband, earth station, mobile, regulation,
satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 980 V1.3.1 (2022-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.0 Objective . 14
4.1.1 Environmental profile . 14
4.1.2 Void . 14
4.1.3 Operating configurations . 14
4.1.4 Presentation of equipment for testing purposes . 14
4.1.5 Choice of model for testing . 15
4.1.6 Operation of multiple NEST on a single frequency . 15
4.2 Conformance requirements . 15
4.2.1 Void . 15
4.2.2 Antenna beam pointing . 15
4.2.2.1 Pointing accuracy . 15
4.2.2.1.1 Purpose . 15
4.2.2.1.2 Antenna Beam Pointing error . 15
4.2.2.2 Pointing error detection . 15
4.2.2.2.1 Purpose . 15
4.2.2.2.2 Pointing error detection specification . 16
4.2.2.3 Conformance tests . 16
4.2.3 Off-axis spurious radiation . 16
4.2.3.1 Justification . 16
4.2.3.2 Specification. 16
4.2.3.3 Conformance tests . 17
4.2.4 On-axis spurious radiation . 17
4.2.4.1 Justification . 17
4.2.4.2 Specification. 17
4.2.4.2.1 "Carrier-on" radio state . 17
4.2.4.2.2 "Carrier-off" and "Emissions disabled" radio states . 18
4.2.4.3 Conformance tests . 18
4.2.5 Carrier suppression . 18
4.2.5.1 Justification . 18
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Cessation of emissions . 18
4.2.6.1 Justification . 18
4.2.6.2 Specification. 18
4.2.6.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.6.2.2 Specification 2: Conditions under which the NEST shall cease emissions . 19
4.2.6.2.3 Specification 3: Cessation of emissions . 19
4.2.6.2.4 Specification 4: Fault conditions . 20
4.2.6.3 Conformance tests . 20
4.2.7 Identification of the NEST and its location . 20
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 980 V1.3.1 (2022-10)
4.2.7.1 Justification . 20
4.2.7.2 Specification. 20
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 21
4.2.8.1 General - Finite State Machine Model . 21
4.2.8.2 Processor monitoring . 23
4.2.8.2.1 Justification . 23
4.2.8.2.2 Specification . 23
4.2.8.2.3 Conformance tests . 24
4.2.8.3 Transmit subsystem monitoring . 24
4.2.8.3.1 Justification . 24
4.2.8.3.2 Specification . 24
4.2.8.3.3 Conformance tests . 24
4.2.8.4 Power-on/Reset . 24
4.2.8.4.1 Justification . 24
4.2.8.4.2 Specification . 24
4.2.8.4.3 Conformance tests . 24
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 24
4.2.8.5.1 Justification . 24
4.2.8.5.2 Specification . 25
4.2.8.5.3 Conformance tests . 25
4.2.8.6 Network control commands . 25
4.2.8.6.1 Justification . 25
4.2.8.6.2 Specification . 26
4.2.8.6.3 Conformance tests . 26
4.2.8.7 Initial burst transmission . 26
4.2.8.7.1 Justification . 26
4.2.8.7.2 Specification . 26
4.2.8.7.3 Conformance tests . 26
4.2.8.8 Inhibition of transmissions . 27
4.2.8.8.1 Justification . 27
4.2.8.8.2 Specification . 27
4.2.8.8.3 Conformance tests . 27
4.2.9 Receive antenna off-axis gain pattern . 27
4.2.9.1 Justification . 27
4.2.9.2 Specification. 27
4.2.9.3 Conformance tests . 28
4.2.10 Blocking performance . 28
4.2.10.1 Justification . 28
4.2.10.2 Specification. 28
4.2.10.3 Conformance tests . 28
4.2.11 Adjacent Signal Selectivity . 28
4.2.11.1 Justification . 28
4.2.11.2 Specification. 29
4.2.11.3 Conformance tests . 29
5 Testing for compliance with technical requirements . 29
5.1 Environmental conditions for testing . 29
5.2 Ancillary Equipment . 29
5.3 Nominated Bandwidth . 29
5.4 Essential radio test suites . 29
6 Test methods for all aspects of the NEST . 30
6.1 General . 30
6.1.1 General requirements . 30
6.2 Off-axis spurious radiation . 30
6.2.1 General . 30
6.2.2 Test method . 30
6.2.2.1 General . 30
6.2.2.2 Multi-carrier operation . 31
6.2.3 Measurements up to 1 000 MHz . 31
6.2.3.1 Test site . 31
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 980 V1.3.1 (2022-10)
6.2.3.2 Void. 31
6.2.3.3 Procedure . 31
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 32
6.2.4.2.1 Test site. 32
6.2.4.2.2 Procedure . 32
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32
6.2.4.3.1 Test site. 32
6.2.4.3.2 Procedure . 33
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 34
6.2.4.4.1 Test site. 34
6.2.4.4.2 Procedure . 34
6.3 On-axis spurious radiation . 35
6.3.1 Test method . 35
6.3.1.1 General . 35
6.3.1.2 Test site . 35
6.3.1.3 Method of measurement . 35
6.3.1.3.1 General . 35
6.3.1.3.2 Method of measurement at the antenna flange . 35
6.3.1.3.3 Method of measurement for an EUT with antenna . 37
6.4 Void . 38
6.5 Carrier suppression . 38
6.5.1 General . 38
6.5.2 Test method . 38
6.6 Antenna beam pointing . 39
6.6.1 General . 39
6.6.2 Test methods . 39
6.7 Cessation of emissions of the NEST . 40
6.7.1 General . 40
6.7.2 Test Method . 40
6.7.2.1 Required documentation and preparation of the test . 40
6.7.2.2 Cessation of emissions from the "Transmission enabled" state . 40
6.7.2.3 Cessation of emission from the "Transmission disabled" state . 40
6.7.2.4 Cessation of emission from the "Initial Phase" state . 41
6.7.2.4.1 EUTs transmitting initial bursts . 41
6.7.2.4.2 EUTs not transmitting initial bursts . 41
6.7.2.5 "Single action" means of cessation of emissions. 41
6.7.2.6 Fault conditions . 42
6.8 Identification of NEST and location determination . 42
6.8.1 Test arrangement . 42
6.8.2 Test method . 43
6.9 Control and monitoring functions . 43
6.9.1 General . 43
6.9.2 Test arrangement . 43
6.9.3 Processor monitoring-Test method . 43
6.9.4 Transmit subsystem monitoring-Test method . 43
6.9.5 Power-on/Reset-Test method . 44
6.9.6 Control Channel and Response Channel - Test method . 44
6.9.7 Network Control commands - Test method . 45
6.9.8 Initial burst transmission - Test method . 46
6.9.9 Inhibition of transmission - Test method .
...
Draft ETSI EN 303 980 V1.3.0 (2022-07)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed and in-motion Earth Stations communicating with
non-geostationary satellite systems (NEST)
in the 11 GHz to 14 GHz frequency bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 980 V1.3.0 (2022-07)
Reference
REN/SES-00460
Keywords
broadband, earth station, mobile, regulation,
satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 980 V1.3.0 (2022-07)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.0 Objective . 14
4.1.1 Environmental profile . 14
4.1.2 Void . 14
4.1.3 Operating configurations . 14
4.1.4 Presentation of equipment for testing purposes . 14
4.1.5 Choice of model for testing . 15
4.1.6 Operation of multiple NEST on a single frequency . 15
4.2 Conformance requirements . 15
4.2.1 Void . 15
4.2.2 Antenna beam pointing . 15
4.2.2.1 Pointing accuracy . 15
4.2.2.1.1 Purpose . 15
4.2.2.1.2 Antenna Beam Pointing error . 15
4.2.2.2 Pointing error detection . 15
4.2.2.2.1 Purpose . 15
4.2.2.2.2 Pointing error detection specification . 16
4.2.2.3 Conformance tests . 16
4.2.3 Off-axis spurious radiation . 16
4.2.3.1 Justification . 16
4.2.3.2 Specification. 16
4.2.3.3 Conformance tests . 17
4.2.4 On-axis spurious radiation . 17
4.2.4.1 Justification . 17
4.2.4.2 Specification. 17
4.2.4.2.1 "Carrier-on" radio state . 17
4.2.4.2.2 "Carrier-off" and "Emissions disabled" radio states . 18
4.2.4.3 Conformance tests . 18
4.2.5 Carrier suppression . 18
4.2.5.1 Justification . 18
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Cessation of emissions . 18
4.2.6.1 Justification . 18
4.2.6.2 Specification. 18
4.2.6.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.6.2.2 Specification 2: Conditions under which the NEST shall cease emissions . 19
4.2.6.2.3 Specification 3: Cessation of emissions . 19
4.2.6.2.4 Specification 4: Fault conditions . 20
4.2.6.3 Conformance tests . 20
4.2.7 Identification of the NEST and its location . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 980 V1.3.0 (2022-07)
4.2.7.1 Justification . 20
4.2.7.2 Specification. 20
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 21
4.2.8.1 General - Finite State Machine Model . 21
4.2.8.2 Processor monitoring . 23
4.2.8.2.1 Justification . 23
4.2.8.2.2 Specification . 23
4.2.8.2.3 Conformance tests . 24
4.2.8.3 Transmit subsystem monitoring . 24
4.2.8.3.1 Justification . 24
4.2.8.3.2 Specification . 24
4.2.8.3.3 Conformance tests . 24
4.2.8.4 Power-on/Reset . 24
4.2.8.4.1 Justification . 24
4.2.8.4.2 Specification . 24
4.2.8.4.3 Conformance tests . 24
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 24
4.2.8.5.1 Justification . 24
4.2.8.5.2 Specification . 25
4.2.8.5.3 Conformance tests . 25
4.2.8.6 Network control commands . 25
4.2.8.6.1 Justification . 25
4.2.8.6.2 Specification . 26
4.2.8.6.3 Conformance tests . 26
4.2.8.7 Initial burst transmission . 26
4.2.8.7.1 Justification . 26
4.2.8.7.2 Specification . 26
4.2.8.7.3 Conformance tests . 26
4.2.8.8 Inhibition of transmissions . 27
4.2.8.8.1 Justification . 27
4.2.8.8.2 Specification . 27
4.2.8.8.3 Conformance tests . 27
4.2.9 Receive antenna off-axis gain pattern . 27
4.2.9.1 Justification . 27
4.2.9.2 Specification. 27
4.2.9.3 Conformance tests . 28
4.2.10 Blocking performance . 28
4.2.10.1 Justification . 28
4.2.10.2 Specification. 28
4.2.10.3 Conformance tests . 28
4.2.11 Adjacent Signal Selectivity . 28
4.2.11.1 Justification . 28
4.2.11.2 Specification. 29
4.2.11.3 Conformance tests . 29
5 Testing for compliance with technical requirements . 29
5.1 Environmental conditions for testing . 29
5.2 Ancillary Equipment . 29
5.3 Nominated Bandwidth . 29
5.4 Essential radio test suites . 29
6 Test methods for all aspects of the NEST . 30
6.1 General . 30
6.1.1 General requirements . 30
6.2 Off-axis spurious radiation . 30
6.2.1 General . 30
6.2.2 Test method . 30
6.2.2.1 General . 30
6.2.2.2 Multi-carrier operation . 31
6.2.3 Measurements up to 1 000 MHz . 31
6.2.3.1 Test site . 31
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 980 V1.3.0 (2022-07)
6.2.3.2 Void. 31
6.2.3.3 Procedure . 31
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 32
6.2.4.2.1 Test site. 32
6.2.4.2.2 Procedure . 32
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32
6.2.4.3.1 Test site. 32
6.2.4.3.2 Procedure . 33
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 34
6.2.4.4.1 Test site. 34
6.2.4.4.2 Procedure . 34
6.3 On-axis spurious radiation . 35
6.3.1 Test method . 35
6.3.1.1 General . 35
6.3.1.2 Test site . 35
6.3.1.3 Method of measurement . 35
6.3.1.3.1 General . 35
6.3.1.3.2 Method of measurement at the antenna flange . 35
6.3.1.3.3 Method of measurement for an EUT with antenna . 37
6.4 Void . 38
6.5 Carrier suppression . 38
6.5.1 General . 38
6.5.2 Test method . 38
6.6 Antenna beam pointing . 39
6.6.1 General . 39
6.6.2 Test methods . 39
6.7 Cessation of emissions of the NEST . 40
6.7.1 General . 40
6.7.2 Test Method . 40
6.7.2.1 Required documentation and preparation of the test . 40
6.7.2.2 Cessation of emissions from the "Transmission enabled" state . 40
6.7.2.3 Cessation of emission from the "Transmission disabled" state . 40
6.7.2.4 Cessation of emission from the "Initial Phase" state . 41
6.7.2.4.1 EUTs transmitting initial bursts . 41
6.7.2.4.2 EUTs not transmitting initial bursts . 41
6.7.2.5 "Single action" means of cessation of emissions. 41
6.7.2.6 Fault conditions . 42
6.8 Identification of NEST and location determination . 42
6.8.1 Test arrangement . 42
6.8.2 Test method . 43
6.9 Control and monitoring functions . 43
6.9.1 General . 43
6.9.2 Test arrangement . 43
6.9.3 Processor monitoring-Test method . 43
6.9.4 Transmit subsystem monitoring-Test method . 43
6.9.5 Power-on/Reset-Test method . 44
6.9.6 Control Channel and Response Channel - Test method . 44
6.9.7 Network Control commands - Test method . 45
6.9.8 Initial burst transmission - Test method . 46
6.9.9 Inhibition of transmission
...
SLOVENSKI STANDARD
oSIST prEN 303 980 V1.3.0:2022
01-september-2022
Satelitske zemeljske postaje in sistemi (SES) - Nepremične in premične zemeljske
postaje, ki komunicirajo z negeostacionarnimi satelitskimi sistemi (NEST) v
frekvenčnih pasovih od 11 GHz do 14 GHz - Harmonizirani standard za dostop do
radijskega spektra
Satellite Earth Stations and Systems (SES) - Fixed and in-motion Earth Stations
communicating with non-geostationary satellite systems (NEST) in the 11 GHz to 14
GHz frequency bands - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 980 V1.3.0 (2022-07)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
oSIST prEN 303 980 V1.3.0:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 980 V1.3.0:2022
---------------------- Page: 2 ----------------------
oSIST prEN 303 980 V1.3.0:2022
Draft ETSI EN 303 980 V1.3.0 (2022-07)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed and in-motion Earth Stations communicating with
non-geostationary satellite systems (NEST)
in the 11 GHz to 14 GHz frequency bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
oSIST prEN 303 980 V1.3.0:2022
2 Draft ETSI EN 303 980 V1.3.0 (2022-07)
Reference
REN/SES-00460
Keywords
broadband, earth station, mobile, regulation,
satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 980 V1.3.0:2022
3 Draft ETSI EN 303 980 V1.3.0 (2022-07)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.0 Objective . 14
4.1.1 Environmental profile . 14
4.1.2 Void . 14
4.1.3 Operating configurations . 14
4.1.4 Presentation of equipment for testing purposes . 14
4.1.5 Choice of model for testing . 15
4.1.6 Operation of multiple NEST on a single frequency . 15
4.2 Conformance requirements . 15
4.2.1 Void . 15
4.2.2 Antenna beam pointing . 15
4.2.2.1 Pointing accuracy . 15
4.2.2.1.1 Purpose . 15
4.2.2.1.2 Antenna Beam Pointing error . 15
4.2.2.2 Pointing error detection . 15
4.2.2.2.1 Purpose . 15
4.2.2.2.2 Pointing error detection specification . 16
4.2.2.3 Conformance tests . 16
4.2.3 Off-axis spurious radiation . 16
4.2.3.1 Justification . 16
4.2.3.2 Specification. 16
4.2.3.3 Conformance tests . 17
4.2.4 On-axis spurious radiation . 17
4.2.4.1 Justification . 17
4.2.4.2 Specification. 17
4.2.4.2.1 "Carrier-on" radio state . 17
4.2.4.2.2 "Carrier-off" and "Emissions disabled" radio states . 18
4.2.4.3 Conformance tests . 18
4.2.5 Carrier suppression . 18
4.2.5.1 Justification . 18
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Cessation of emissions . 18
4.2.6.1 Justification . 18
4.2.6.2 Specification. 18
4.2.6.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.6.2.2 Specification 2: Conditions under which the NEST shall cease emissions . 19
4.2.6.2.3 Specification 3: Cessation of emissions . 19
4.2.6.2.4 Specification 4: Fault conditions . 20
4.2.6.3 Conformance tests . 20
4.2.7 Identification of the NEST and its location . 20
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 980 V1.3.0:2022
4 Draft ETSI EN 303 980 V1.3.0 (2022-07)
4.2.7.1 Justification . 20
4.2.7.2 Specification. 20
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 21
4.2.8.1 General - Finite State Machine Model . 21
4.2.8.2 Processor monitoring . 23
4.2.8.2.1 Justification . 23
4.2.8.2.2 Specification . 23
4.2.8.2.3 Conformance tests . 24
4.2.8.3 Transmit subsystem monitoring . 24
4.2.8.3.1 Justification . 24
4.2.8.3.2 Specification . 24
4.2.8.3.3 Conformance tests . 24
4.2.8.4 Power-on/Reset . 24
4.2.8.4.1 Justification . 24
4.2.8.4.2 Specification . 24
4.2.8.4.3 Conformance tests . 24
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 24
4.2.8.5.1 Justification . 24
4.2.8.5.2 Specification . 25
4.2.8.5.3 Conformance tests . 25
4.2.8.6 Network control commands . 25
4.2.8.6.1 Justification . 25
4.2.8.6.2 Specification . 26
4.2.8.6.3 Conformance tests . 26
4.2.8.7 Initial burst transmission . 26
4.2.8.7.1 Justification . 26
4.2.8.7.2 Specification . 26
4.2.8.7.3 Conformance tests . 26
4.2.8.8 Inhibition of transmissions . 27
4.2.8.8.1 Justification . 27
4.2.8.8.2 Specification . 27
4.2.8.8.3 Conformance tests . 27
4.2.9 Receive antenna off-axis gain pattern . 27
4.2.9.1 Justification . 27
4.2.9.2 Specification. 27
4.2.9.3 Conformance tests . 28
4.2.10 Blocking performance . 28
4.2.10.1 Justification . 28
4.2.10.2 Specification. 28
4.2.10.3 Conformance tests . 28
4.2.11 Adjacent Signal Selectivity . 28
4.2.11.1 Justification . 28
4.2.11.2 Specification. 29
4.2.11.3 Conformance tests . 29
5 Testing for compliance with technical requirements . 29
5.1 Environmental conditions for testing . 29
5.2 Ancillary Equipment . 29
5.3 Nominated Bandwidth . 29
5.4 Essential radio test suites . 29
6 Test methods for all aspects of the NEST . 30
6.1 General . 30
6.1.1 General requirements . 30
6.2 Off-axis spurious radiation . 30
6.2.1 General . 30
6.2.2 Test method . 30
6.2.2.1 General . 30
6.2.2.2 Multi-carrier operation . 31
6.2.3 Measurements up to 1 000 MHz . 31
6.2.3.1 Test site . 31
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 980 V1.3.0:2022
5 Draft ETSI EN 303 980 V1.3.0 (2022-07)
6.2.3.2 Void. 31
6.2.3.3 Procedure . 31
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 32
6.2.4.2.1 Test site. 32
6.2.4.2.2 Procedure . 32
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32
6.2.4.3.1 Test site. 32
6.2.4.3.2 Procedure . 33
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 34
6.2.4.4.1 Test site. 34
6.2.4.4.2 Procedure . 34
6.3 On-axis spurious radiation . 35
6.3.1 Test method . 35
6.3.1.1 General . 35
6.3.1.2 Test site . 35
6.3.1.3 Method of measurement . 35
6.3.1.3.1 General . 35
6.3.1.3.2 Method of measurement at the antenna flange . 35
6.3.1.3.3 Method of measurement for an EUT with antenna . 37
6.4 Void . 38
6.5 Carrier suppression . 38
6.5.1 General . 38
6.5.2 Test method . 38
6.6 Antenna beam pointing . 39
6.6.1 General . 39
6.6.2 Test methods . 39
6.7 Cessation of emissions of the NEST . 40
6.7.1 General . 40
6.7.2 Test Method . 40
6.7.2.1 Required documentation and preparation of the test . 40
6.7.2.2 Cessation of emissions from the "Transmission enabled" state . 40
6.7.2.3 Cessation of emission from the "Transmission disabled" state . 40
6.7.2.4 Cessation of emission from the "Initial Phase" state . 41
6.7.2.4.1 EUTs transmitting initial bursts . 41
6.7.2.4.2 EUTs not transmitting initial bursts . 41
6.7.2.5 "Single action" means of cessation of emissions. 41
6.7.2.6 Fault conditions . 42
6.8 Identification of NEST and location determination . 42
6.8.1 Test arrangement . 42
6.8.2 Test method . 43
6.9 Control and monitoring functions . 43
6.9.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.