ETSI TS 186 017-2 V1.0.0 (2008-06)
Telecommunications and Internet converged Services and Protocols for Advanced Networking (TISPAN); PSTN/ISDN simulation services; Anonymous Communication Rejection (ACR) and Communication Barring (CB); Part 2: Test Suite Structure and Test Purposes (TSS&TP)
Telecommunications and Internet converged Services and Protocols for Advanced Networking (TISPAN); PSTN/ISDN simulation services; Anonymous Communication Rejection (ACR) and Communication Barring (CB); Part 2: Test Suite Structure and Test Purposes (TSS&TP)
DTS/TISPAN-06038-2-NGN
General Information
Buy Standard
Standards Content (Sample)
ETSI TS 186 017-2 V1.0.0 (2008-06)
Technical Specification
Telecommunications and Internet converged Services and
Protocols for Advanced Networking (TISPAN);
PSTN/ISDN simulation services;
Anonymous Communication Rejection (ACR) and
Communication Barring (CB);
Part 2: Test Suite Structure and Test Purposes (TSS&TP)
---------------------- Page: 1 ----------------------
2 ETSI TS 186 017-2 V1.0.0 (2008-06)
Reference
DTS/TISPAN-06038-2-NGN
Keywords
CB, IMS, testing, TSS&TP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI TS 186 017-2 V1.0.0 (2008-06)
Contents
Intellectual Property Rights.4
Foreword.4
1 Scope.5
2 References.5
2.1 Normative references.5
2.2 Informative references.6
3 Definitions and abbreviations.6
3.1 Definitions.6
3.2 Abbreviations.6
4 Test Suite Structure (TSS).7
5 Test Purposes (TP).7
5.1 Introduction.7
5.1.1 TP naming convention.7
5.1.2 Test strategy.7
5.2 TPs for Anonymous Communication Rejection (ACR).8
5.2.1 Action for ACR at the terminating AS.8
5.3 TPs for Communication Barring (CB) .14
5.3.1 Actions for OCB at the originating AS.14
5.3.2 Actions for ICB at the terminating AS.15
5.4 Interaction with other simulation services.16
5.4.1 Originating Identification Presentation (OIP).16
5.4.2 Communication Diversion services (CDIV).16
5.5 Test purposes for the ISUP/SIP Interworking .18
5.5.1 Interworking from ISUP to SIP (Outgoing Call) .18
5.5.2 Interworking from SIP to ISUP (Incoming Call).18
History .19
ETSI
---------------------- Page: 3 ----------------------
4 ETSI TS 186 017-2 V1.0.0 (2008-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Telecommunications and Internet
converged Services and Protocols for Advanced Networking (TISPAN).
The present document is part 2 of a multi-part deliverable covering the Anonymous Communication Rejection (ACR)
and Communication Barring (CB) simulation services, as identified below:
Part 1: "Protocol Implementation Conformance Statement (PICS)";
Part 2: "Test Suite Structure and Test Purposes (TSS&TP)";
Part 3: "Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)".
ETSI
---------------------- Page: 4 ----------------------
5 ETSI TS 186 017-2 V1.0.0 (2008-06)
1 Scope
The present document specifies the test suite structure and test purposes of the Anonymous Communication Rejection
(ACR) and Communication Barring (CB) simulation service, based on stage three of the IMS simulation service
Anonymous Call Rejection (ACR), Incoming Communication Barring (ICB) and Outgoing Communication Barring
(OCB). Within the Next Generation Network (NGN) the stage 3 description is specified using the IP Multimedia Call
Control Protocol based on Session Initiation Protocol (SIP) and Session Description Protocol (SDP).
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably,
the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the
reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the
method of access to the referenced document and the full network address, with the same punctuation and use of upper
case and lower case letters.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI TS 183 011: "Telecommunications and Internet converged Services and Protocols for
Advanced Networking (TISPAN); PSTN/ISDN simulation services: Anonymous Communication
Rejection (ACR) and Communication Barring (CB); Protocol specification".
[2] ETSI TS 181 002: "Telecommunications and Internet converged Services and Protocols for
Advanced Networking (TISPAN); Multimedia Telephony with PSTN/ISDN simulation services".
[3] IETF RFC 3261: "SIP: Session Initiation Protocol".
ETSI
---------------------- Page: 5 ----------------------
6 ETSI TS 186 017-2 V1.0.0 (2008-06)
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] ETSI TS 186 017-1: "Telecommunications and Internet Converged Services and Protocols for
Advanced Networking (TISPAN); PSTN/ISDN simulation services: Anonymous Communication
Rejection (ACR) and Communication Barring (CB); Part 1: Protocol Implementation
Conformance Statement (PICS)".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TS 181 002 [2] and the following apply:
escaped character: See RFC 3261 [3].
NOTE: This may contain additional information.
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ACK ACKnowledgement
ACR Anonymous Communication Rejection
AS Application Server
CB Communication Barring
CDIV Communication DIVersion services
HOLD communication HOLD
ICB Incoming Communication Barring
IMS IP Multimedia Subsystem
IP Internet Protocol
ISUP ISDN User Part
ISDN Integrated Service Data Network
NGN Next Generation Network
OCB Outgoing Communication Barring
OIP Originating Identification Presentation
PSTN Public Switched Telephone Network
SDP Session Description Protocol
SIP Session Initiation Protocol
SUB SUBaddressing
TP Test Purposes
TSS Test Suite Structure
UA User Agent
ETSI
---------------------- Page: 6 ----------------------
7 ETSI TS 186 017-2 V1.0.0 (2008-06)
4 Test Suite Structure (TSS)
ACR-CB
ACR_terminating_AS ACR-CB_N01_xxx
OBC_originating_AS ACR-CB_N02_xxx
IBC_terminating_AS ACR-CB_N03_xxx
interaction_OIP ACR-CB_N04_xxx
interaction_CDIV ACR-CB_N05_xxx
ISUP-SIP
SS ACR TP612xxx
SIP-ISUP
SS ACR TP515xxx
5 Test Purposes (TP)
5.1 Introduction
For each test requirement a TP is defined.
5.1.1 TP naming convention
TPs are numbered, starting at 001, within each group. Groups are organized according to the TSS. Additional references
are added to identify the actual test suite and whether it applies to the network or the user (see table 1).
Table 1: TP identifier naming convention scheme
Identifier: __
= supplementary service: e.g. "ACR-CB"
= type of IUT: U User – equipment
N Network
= group 2 digit field representing group reference according to TSS
= sequential number (001-999)
5.1.2 Test strategy
As the base standard TS 183 011 [1] contains no explicit requirements for testing, the TPs were generated as a result of
an analysis of the base standard and the PICS specification TS 186 017-1 [i.1]. The criteria applied include the
following:
• whether or not a test case can be built from the TP is not considered.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI TS 186 017-2 V1.0.0 (2008-06)
5.2 TPs for Anonymous Communication Rejection (ACR)
5.2.1 Action for ACR at the terminating AS
TSS TP CB reference Selection expression
ACR_CB/ACR_terminating_AS ACR-CB_N01_001 TS 183 011, clause PICS 1/2
4.5.2.6.2 [1]
Test purpose
ACR service rejects an anonymous communication, Privacy value is id.
Ensure that the ACR service rejects the incoming communication where the request includes the P-Asserted-Identity
header AND the Privacy header indicating “id”.
Ensure that the ACR is sending a 433 (Anonymity Disallowed) response when the communication is rejected.
Preconditions:
incoming-communication-barring active=true
conditions: sub element anonymous is evaluate to “true”
actions: sub element allow is evaluate to “false”
Comments:
UA C SUT UA S
INVITE
100 Trying
433 Anonymity Disallowed
ACK
TSS TP CB reference Selection expression
ACR_CB/ACR_terminating_AS ACR-CB_N01_002 TS 183 011, PICS 1/2 AND PICS 1/4
clause 4.5.2.6.2 [1]
Test purpose
ACR service rejects an anonymous communication, Privacy value is id. An announcement is provided.
Ensure that the ACR service rejects the incoming communication where the request includes the P-Asserted-Identity
header AND the Privacy header indicating “id”.
Ensure that the ACR service provides an announcement to the originating user before sending a 433 (Anonymity
Disallowed) response when the communication is rejected.
Preconditions:
incoming-communication-barring active=true
conditions: sub element anonymous is evaluate to “true”
actions: sub element allow is evaluate to “false”
Comments:
UA C SUT UA S
INVITE
100 Trying
Announcement
433 Anonymity Disallowed
ACK
ETSI
---------------------- Page: 8 ----------------------
9 ETSI TS 186 017-2 V1.0.0 (2008-06)
TSS TP CB reference Selection expression
ACR_CB/ACR_terminating_AS ACR-CB_N01_003 TS 183 011, PICS 1/2 AND PICS 1/5
clause 4.5.2.6.2 [1]
Test purpose
ACR service forwards an anonymous communication, Privacy value is id.
Ensure that the ACR service rejects the incoming communication where the request includes the P-Asserted-Identity
header AND the Privacy header indicating “id”.
Ensure that the communication is forwarded to voice message service instead of rejecting the communication with
a 433 (Anonymity Disallowed) final response.
Preconditions:
incoming-communication-barring active=true
conditions: sub element anonymous is evaluate to “true”
actions: sub element allow is evaluate to “false”
Comments:
UA C SUT UA S
INVITE
100 Trying
200 OK INVITE
ACK
Voice message
BYE
200 OK BYE
TSS TP CB reference Selection expression
ACR_CB/ACR_terminating_AS ACR-CB_N01_004 TS 183 011, PICS 1/2
clause 4.5.2.6.2 [1]
Test purpose
ACR service rejects an anonymous communication, Privacy value is header.
Ensure that the ACR service rejects the incoming communication where the request includes the P-Asserted-Iden
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.