ETSI ETS 300 474-2 ed.1 (1996-08)
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 2: Fixed radio Termination (FT)
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 2: Fixed radio Termination (FT)
DE/RES-03043-2
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Profil generičnega dostopa (GAP) - Seznam zahtev za profil in za profil specifične proformne izjave o skladnosti izvedbe (ICS) - 2. del: Fiksna radijska zaključitev (FT)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.7Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 2: Fixed radio Termination (FT)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 474-2 E13SIST ETS 300 474-2:1999en01-MDQXDU19993SIST ETS 300 474-2:1999SLOVENSKI
STANDARD
SIST ETS 300 474-2:1999
EUROPEANETS 300 474-2TELECOMMUNICATIONAugust 1996STANDARDSource: ETSI TC-RESReference: DE/RES-03043-2ICS:33.020, 33.060.50Key words:DECT, GAP, ICS, FTRadio Equipment and Systems (RES);Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile requirement list and profile-specificImplementation Conformance Statement (ICS) proforma;Part 2: Fixed radio Termination (FT)ETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.frTel.: +33 92 94 42 00 - Fax: +33 93 65 47 16Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1996. All rights reserved.SIST ETS 300 474-2:1999
Page 2ETS 300 474-2: August 1996Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 474-2:1999
Page 3ETS 300 474-2: August 1996ContentsForeword.51Scope.72Normative references.73Definitions abbreviations.83.1Definitions.83.2Abbreviations.84Conformance requirement concerning profile ICS.8Annex A (normative):Requirement lists for DECT FT.9A.1General.9A.1.1Profile Requirement List (profile RL).9A.1.2General conditions.10A.2Network layer - FT: profile Requirement List (profile RL).10A.2.1Major capabilities.10A.2.1.1Entities.10A.2.1.2CC features.11A.2.1.3MM features.12A.2.1.4SS features (services).13A.2.1.5LCE features.14A.2.1.6Procedures.14A.2.2Messages.16A.2.2.1Call control messages.16A.2.2.2Mobility management messages.22A.2.2.3Connection-related and connection independent supplement servicemessages.27A.2.2.4Link control entity messages.27A.2.3Information elements.28A.2.3.1Fixed length information element support.28A.2.3.2Variable length information element supported.29A.2.3.3Escape information elements support.33A.2.4Protocol error handling.33A.3Data link control layer - FT: profile ICS.33A.3.1Capabilities.33A.3.1.1Services.33A.3.1.1.1C-plane services.34A.3.1.1.2U-plane services.34A.3.1.1.3Management services.34A.3.1.2Procedures.35A.3.1.2.1Generic signalling procedures.35A.3.1.2.2Class A procedures.35A.3.1.2.3Broadcast procedures.35A.3.1.2.4LU1 procedures.35A.3.1.2.5Management procedures.36A.3.1.3Parameters.36A.3.1.3.1LU1 parameters.36A.3.1.4Messages.37A.3.1.4.1C-plane PDUs.37A.4Medium access control layer - FT: profile ICS.37SIST ETS 300 474-2:1999
Page 4ETS 300 474-2: August 1996A.4.1Major Capabilities.37A.4.1.1Services.37A.4.1.1.1Connection oriented control services.37A.4.1.1.2Broadcast control services.38A.4.1.1.3Multiplexing services.38A.4.1.1.4Management services.39A.4.1.2Procedures.39A.4.1.2.1Connection setup procedures.39A.4.1.2.2Connection data transfer procedures.39A.4.1.2.3Connection handover procedures.40A.4.1.2.4Connection release procedures.40A.4.1.2.5Broadcast procedures.40A.4.1.2.6CSF multiplexing procedures.41A.4.1.2.7Layer management procedures.41A.4.1.3Other capabilities.41A.4.2Messages.42A.4.2.1A - Field.42A.4.2.1.1A - field header - B-field identification.42A.4.2.2A - Field Messages.42A.4.2.2.1Paging tail messages supported.42A.4.2.2.2PT messages information type.43A.4.2.2.3Mac control messages supported.43A.4.2.2.4Broadcast and connectionless (BCL) messages.44A.5Physical layer - FT: profile ICS.44A.5.1Physical layer procedures.44Annex B (normative):GAP profile-specific ICS proforma for FT.46B.1Introduction for completing the profile-specific ICS proforma.46B.1.1Purposes and structure.46B.1.3Instructions for completing the profile-specific ICS.48B.2Identification of the implementation.48B.2.1Date of statement.48B.2.2Implementation Under Test (IUT) identification.48B.2.3System Under Test (SUT) identification.48B.2.4Product supplier.49B.2.5Client identification.49B.2.6Contact person identification.49B.3Identification of the profile.50B.3.1Defect report numbers and amendments implemented.50B.3.2Addenda implemented.50B.4Global statement of conformance.50B.5Capabilities.51B.5.1NWK profile-specific ICS proforma for FT.51B.5.1.1General requirements.51B.5.1.2Application features.51B.5.1.3Application Procedures.51B.5.1.4Management procedures.51B.5.2DLC profile-specific ICS proforma for FT.52B.5.2.1Services.52B.5.3MAC profile-specific ICS proforma for FT.52B.5.3.1Services.52B.5.3.1.1Extended frequency allocation service.52B.5.4PH Profile-specific ICS proforma for FT.52B.5.4.1Requirements.52History.53SIST ETS 300 474-2:1999
Page 5ETS 300 474-2: August 1996ForewordThis European Telecommunication Standard (ETS) has been produced by the Radio Equipment andSystems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).This European Telecommunication Standard (ETS) has been produced by the Radio Equipment andSystems (RES), Technical Committee of the European Telecommunications Standards Institute (ETSI).The DECT Generic Access Profile (GAP) profile requirement list and profile-specific ImplementationConformance Statement (ICS) proforma standard comprises two parts as follows:Part 1:"Portable radio Termination (PT)".Part 2:"Fixed radio Termination (FT)".Annex A contains the requirement lists for the FT GAP.Annex B contains the profile-specific ICS proforma for the FT GAP.Transposition datesDate of adoption of this ETS:16 August 1996Date of latest announcement of this ETS (doa):30 November 1996Date of latest publication of new National Standardor endorsement of this ETS (dop/e):31 May 1997Date of withdrawal of any conflicting National Standard (dow):31 May 1997SIST ETS 300 474-2:1999
Page 6ETS 300 474-2: August 1996blank pageSIST ETS 300 474-2:1999
Page 7ETS 300 474-2: August 19961ScopeThis European Telecommunication Standard (ETS) provides the profile requirment list and profile-specificImplementation Conformance Statement (profile ICS) proforma for the Digital Enhanced CordlessTelecommunications (DECT) Generic Accesss Profile (GAP) at the Fixed radio Termination (FT) asdefined in ETS 300 444 [2] in compliance with the relevant requirements and in accordance with therelevant guidance given in ISO/IEC 9646-7 [8].The supplier of an implementation which is claimed to conform to ETS 300 444 [2] is required to completea copy of the Protocol Implementation Conformance Statement (PICS) proforma ETS 300 476 parts 4, 5,6 and 7 [3], [4], [5] and [6] with the replacements from annex A of this standard, as well as, a copy of theand profile-specific ICS proforma provided in the annex B of this standard.2Normative referencesThis ETS incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this ETS only when incorporated in it by amendment or revision. For undated references the latestedition of the publication referred to applies.[1]ETS 300 175-5: "Radio Equipment and Systems Digital Enhanced CordlessTelecommunications Common Interface Part 5: Network Layer".[2]ETS 300 444: "Radio Equipment and Systems (RES) Digital European CorldlessTelecommunications (DECT): Generic Access Profile (GAP)”.[3]ETS 300 476-4: "Radio Equipment and Systems; Digital Enhanced CordlessTelecommunications (DECT), Common Interface, Protocol ImplementationConformance Statement (PICS) proforma, Network layer - Fixed Termination(FT)".[4]ETS 300 476-5: "Radio Equipment and Systems; Digital Enhanced CordlessTelecommunications (DECT), Common Interface, Protocol ImplementationConformance Statement (PICS) proforma, Data Link Control layer - FixedTermination (FT)".[5]ETS 300 476-6: "Radio Equipment and Systems; Digital Enhanced CordlessTelecommunications (DECT), Common Interface, Protocol ImplementationConformance Statement (PICS) proforma, Medium Access Control layer - FixedTermination (FT)".[6]ETS 300 476-7: "Radio Equipment and Systems; Digital Enhanced CordlessTelecommunications (DECT), Common Interface, Protocol ImplementationConformance Statement (PICS) proforma, Physical layer".[7]ISO/IEC 9646-1 (1995): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 1:General concepts".[8]ISO/IEC 9646-7 (1995): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 7:Implementation Conformance Statements".SIST ETS 300 474-2:1999
Page 8ETS 300 474-2: August 19963Definitions abbreviations3.1DefinitionsFor the purposes of this ETS, the following terms and definitions apply:a)the terms defined in ISO/IEC 9646-7 [8];b)the definitions in ETS 300 444 [2]; andc)the following terms defined in ISO/IEC 9646-1 [7]:-PICS proforma;-profile Implementation Conformance Statement (profile ICS).3.2AbbreviationsFor the purposes of this ETS, the abbreviations defined in ISO/IEC 9646-1 [7] and ETS 300 444 [2] apply.4Conformance requirement concerning profile ICSThe supplier of a protocol implementation which is claimed to conform to the portable termination specificrequirements of ETS 300 444 [2] shall verify that his protocol implementation meets the profileRequirements Lists (RLs) for each DECT protocol layer, contained in annex A of this standard, and shallcomplete a copy of the profile-specific ICS proforma provided in annex B and shall provide the informationnecessary to identify both the supplier and the implementation.SIST ETS 300 474-2:1999
Page 9ETS 300 474-2: August 1996Annex A (normative):Requirement lists for DECT FTA.1GeneralThe supplier of a protocol implementation which is claimed to conform to the portable termination specificrequirements of ETS 300 444 [2] shall verify that his particular (NWK, DLC and MAC) layer protocolimplementation meets the profile RL for this layer. For this, he shall complete a copy of the corespondonglayer PICS proforma contained in annex A of ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6] updatedwith the requirements from this annex.A.1.1Profile Requirement List (profile RL)The profile Requirement List (profile RL) for the NWK, DLC, MAC and PH layer as defined in this sectionis based on ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6]. For every capability listed in ETS 300 476parts 4, 5, 6 and 7 [3] [4] [5] and [6], the profile requirements are expressed by restriction upon allowedsupport answers in ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6] depending on whether theimplementation is to work in Residential/Business (R/B) or Public (P) environment. The profile RL isproduced by copying selected tables from ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6], removing thecolumn(s) to be completed by the supplier, and adding a new set of columns giving the new profilerequirements, both in terms of the status and allowed values. The tables are referenced by preceding itwith an “[3]”, "[4]", "[5]" or "[6]" as relevant.Profile status columnWhere it has been seen as necessary two profile status columns are provided one forResidential/Business (R/B) environment and one for Public (P) environment.The standardized symbols for the status column are as follows:m or Mmandatory - the capability is required to be supported;o or Ooptional - the capability may be supported or not;n/a or N/Anot applicable - in the given context, it is impossible to use the capability;x or Xprohibited (excluded) - there is a requirement not to use this capability in thegiven context;o.i or O.iqualified optional - for mutually exclusive or selectable options from a set. "i" isan integer which identifies an unique group of related optional items and thelogic of their selection which is defined immediately following the table;ci or Ciconditional - the requirement on the capability ("m", "o", "x" or "n/a") depends onthe support of other optional or conditional items. "i" is an integer identifying anunique conditional status expression which is defined immediately following thetable or which is defined in the general condition table below;i or Iout-of-scope - this capability is outside the scope of the given specification, andhence irrelevant and not subject to conformance testing. This status is inparticular applicable for data fields which are reserved for future use. Thestructure of such fields has to be supported, but the value is undefined and thusto be ignored.Reference columnThe reference column gives reference to ETS 300 444 [2], except where explicitly stated otherwise.SIST ETS 300 474-2:1999
Page 10ETS 300 474-2: August 1996A.1.2General conditionsTable A.1: General condition tableCondition identifierCondition definitionNOTE AThe status of the relevant item is exactly as the status of this item inETS 300 476 Parts 4, 5, 6 and 7 [3] [4] [5] and [6]. The item has beenincluded as the profile reference column include reference to the profile thatdescribes the item more in details.A.2Network layer - FT: profile Requirement List (profile RL)A.2.1Major capabilitiesA.2.1.1EntitiesTo express the profile requirements of ETS 300 444 [2], the following table indicates the change of statusfor support of entities.Table A.2: ETS 300 476-4 [3] Table A.12 Entity supportedItemEntity nameProfilereferenceProfilestatus R/BProfilestatus P1Call control (CC)6.2mm2Call Independent Supplementary Services (CISS)-ii3Connection oriented message services (COMS)-ii4ConnectionLess message services (CLMS)-ii5Mobility management (MM)6.2mm6Link control entity (LCE)6.2mm7Management (LLME)13mmSIST ETS 300 474-2:1999
Page 11ETS 300 474-2: August 1996A.2.1.2CC featuresTo express the profile requirements of ETS 300 444 [2], the following table indicates the change of statusfor support of NWK layer CC features.Table A.3: ETS 300 476-4 [3] Table A.13 CC features supportedItemCall Control featuresProfilereferenceProfilestatus R/BProfilestatus P1Bell off (Alerting)6.2mm2Bell on (Alerting)6.2mm3Control of supervisory tones-ii4Dial tone detection indication-ii5Dialled digits (basic)6.2mm6Dialled digits additional-ii7Dialling delimiter-ii8Dialling delimiter request-ii9Display control characters6.2oo10Emergency service access request-ii11External Handover (inter-cell)-ii12Fixed part/portable part capability exchange-ii13Go to DTMF (infinite tone length)6.2oo14Go to DTMF signalling (defined tone length)6.2om15Go to Pulse6.2oo16Group address-ii17Incoming call6.2mm18Internal call6.2oo19Off hook6.2mm20On hook (full release)6.2mm21Outgoing call6.2mm22Packet mode-ii23Partial release6.2oo24Pause (dialling pause)6.2oo25Register recall6.2oo26Signalling of display characters6.2oo27Selection of bearer service-ii28Service call6.2oo29Service change-iiSIST ETS 300 474-2:1999
Page 12ETS 300 474-2: August 1996A.2.1.3MM featuresTo express the profile requirements of ETS 300 444 [2], the following table indicates the change of statusfor support of NWK layer MM features.Table A.4: ETS 300 476-4 [3] Table A.14 MM features supportedItemMobility Management featuresProfilereferenceProfilestatus R/BProfilestatus P1Authentication of FT6.2oo2Authentication of PT6.2om3Authentication of user6.2oo4Encryption activation FT initiated6.2om5Encryption activation PT initiated6.2oo6Encryption deactivation FT initiated6.2oo7Encryption deactivation PT initiated6.2oo8Identification of PP6.2oo9Inter-operator roaming registration-ii10Location de-registration-ii11Location registration6.2om12Multiple subscription registration6.6n/an/a13On air key allocation6.2oo14Service class indication/assignment6.2om15Silent polling-ii16Subscription registration procedure on-air6.2mm17Subscription registration user procedure with DECTauthentication module-ii18Subscription registration user procedures keypad (digit entryonly)-ii19Terminate access rights FT initiated6.2oo20Terminate access rights PT initiated-ii21ZAP6.2oo22MM Partial release8.39mm23Temporary identity assign-iiSIST ETS 300 474-2:1999
Page 13ETS 300 474-2: August 1996A.2.1.4SS features (services)To express the profile requirements of ETS 300 444 [2], the following table indicates the change of statusfor support of NWK layer SS features (services).Table A.5: ETS 300 476-4 [3] Table A.15 SS features (services) supportedItemCC(CRSS) and CISS featuresRef.Profilestatus R/BProfilestatus P1Advice of charge (AOC)-ii2Advice of tariff request-ii3Call Deflection (CD)-ii4Call Forwarding Busy (CFB)-ii5Call Forwarding No Reply (CFNR)-ii6Call Forwarding Unconditional (CFU)-ii7Call Waiting (CW)-ii8Calling Line Identification Presentation (CLIP)6.2oo9Calling Line Identification Restriction (CLIR)-ii10Closed User Group (CUG)-ii11Completion of Calls to Busy Subscriber (CCBS)-ii12Call Hold (CH)-ii13CONFerence call add-on (CONF)-ii14COnnected Line identification Presentation (COLP)-ii15COnnected Line identification Restriction (COLR)-ii16Control of echo control functions-ii17Cost information-ii18Credit agency public access service-ii19Credit public access service-ii20Debit public access service-ii21Direct Dialling In (DDI)-ii22Explicit Call Transfer (ECT)-ii23Forced re-connection of held call-ii24FreePHone (FPH)-ii25Hold call (FT to PT)-ii26Hold call (PT to FT)-ii27Indication of teleservice available request-ii28Indication of teleservices available-ii29Malicious Call Identification (MCID)-ii30Multiple Subscriber Number (MSN)-ii31On-demand (hot bill) public access service- CRSS-ii32Queue management-ii33Re-connection of held call (FT to PT)-ii34Re-connection of held call (PT to FT)-ii35Request for indication of temporary subscriber number-CRSS-ii36Selection of required teleservice-ii37Single step Call Transfer (SCT)-ii38Specific trunk carrier selection-ii39SUBaddressing (SUB)-ii40Terminal Portability (TP)-ii41Tree ParTY (3TPY)-ii42User to User Signalling UUS-ii43CISS Partial release-ii44Feature key-ii45Indication of subscriber number-ii46Register recall-ii47Specific line selection-ii48External handover switch-iiSIST ETS 300 474-2:1999
Page 14ETS 300 474-2: August 1996A.2.1.5LCE featuresTo express the profile requirements of ETS 300 444 [2], the following table indicates the change of statusfor support of NWK layer LCE features.Table A.6: ETS 300 476-4 [3] Table A.16 LCE features supportedItemLCE featuresProfilereferenceProfile statusR/BProfile statusP1Connection oriented Link control (Linkcontrol)6.2mm2Connectionless oriented Link control-iiA.2.1.6ProceduresTo express the profile requirements of ETS 300 444 [2], the following tables indicate the change of statusfor support of NWK layer procedures.Table A.7: ETS 300 476-4 [3] Table A.18 CC procedures supportedItemCC proceduresProfilereferenceProfile status R/BProfile statusP1cc_outgoing_normal_call_request8.2mm4cc_outgoing_selection_of_lower_layer_resources-ii5cc_outgoing_connection_of_U_plane8.3, 8.4, 8.5,8.6mm6cc_outgoing_overlap_sending8.3oo7cc_outgoing_call_proceeding8.4oo8cc_outgoing_call_confirmation8.5oo9cc_outgoing_call_connection8.6mm10cc_incoming_call_request8.12mm11cc_incoming_selection_of_lower_layer_resources-ii12cc_incoming_connection_of_U_plane8.15mm13cc_incoming_overlap_receiving-ii14cc_incoming_call_proceeding-ii15cc_incoming_call_confirmation8.13mm16cc_incoming_call_connection8.15mm17cc_sending_terminal_capability-ii18cc_sending_keypad_info8.10mm19cc_call_information8.10ii20cc_normal_call_release8.7mm21cc_partial_release8.9note Anote A22cc_abnormal_call_release8.8mm23cc_release_collisions8.7.2.1mm31cc_timer_f_cc_02_mgt8.7mm32cc_timer_f_cc_03_mgt8.2mm33cc_timer_f_cc_04_mgt-ii34cc_timer_f_cc_01_mgt8.3note Anote A35cc_internal_call_setup8.18cp701cp70136cc_service_call_setup8.20cp702cp70238cc_service_call_keypad8.21cp703cp70339cc_internal_call_keypad8.19cp704cp70440pt_alerting8.14mm41display8.16note Anote Acp701: IF A.3/18 THEN m ELSE i;cp702: IF A.3/18 THEN o ELSE i;cp703: IF A.3/28 THEN m ELSE i;cp704: IF A.3/28 THEN o ELSE i.SIST ETS 300 474-2:1999
Page 15ETS 300 474-2: August 1996Table A.8: ETS 300 476-4 [3] Table A.19 MM procedures supportedItemMobility Management proceduresProfilereferenceProfile statusR/BProfile statusP1mm_identification_of_pt8.22note Anote A2mm_temporary_identity_assignment-ii3mm_authentication_of_pt8.24note Anote A4mm_authentication_of_user8.25note Anote A5mm_authentication_of_ft8.23note Anote A6mm_location_registration8.28note Anote A8mm_location_update8.29cp801note A9mm_obtain_access_rights8.30mm10mm_pt_init_terminate_access_rights-ii11mm_ft_init_terminate_access_rights8.31note Anote A12mm_key_allocation8.32note Anote A13mm_pt_init_parameter_retrieval-ii14mm_ft_init_parameter_retrieval-ii15mm_pt_init_cipher_switching8.34note Anote A16mm_ft_init_cipher_switching8.33note Anote A17mm_zap_increment8.26note Anote A18mm_dck_storing8.27note Am19mm_dck_sending-ii20mm_service_class_mgt8.30, 8.24note Anote A21mm_partial_release8.39mm23mm_timer_f_mm_ident_1_mgt8.28.1.2note Anote A24mm_timer_f_mm_access_2_mgt8.31.1.1note Anote A25mm
...
SLOVENSKI STANDARD
SIST ETS 300 474-2:1999
01-maj-1999
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH '(&7 3URILOJHQHULþQHJD
GRVWRSD *$3 6H]QDP]DKWHY]DSURILOLQ]DSURILOVSHFLILþQHSURIRUPQHL]MDYHR
VNODGQRVWLL]YHGEH ,&6 GHO )LNVQDUDGLMVND]DNOMXþLWHY )7
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP);
Profile requirement list and profile specific Implementation Conformance Statement (ICS)
proforma; Part 2: Fixed radio Termination (FT)
Ta slovenski standard je istoveten z: ETS 300 474-2 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
SIST ETS 300 474-2:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ETS 300 474-2:1999
---------------------- Page: 2 ----------------------
SIST ETS 300 474-2:1999
EUROPEAN ETS 300 474-2
TELECOMMUNICATION August 1996
STANDARD
Source: ETSI TC-RES Reference: DE/RES-03043-2
ICS: 33.020, 33.060.50
Key words: DECT, GAP, ICS, FT
Radio Equipment and Systems (RES);
Digital Enhanced Cordless Telecommunications (DECT);
Generic Access Profile (GAP);
Profile requirement list and profile-specific
Implementation Conformance Statement (ICS) proforma;
Part 2: Fixed radio Termination (FT)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.fr
Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1996. All rights reserved.
---------------------- Page: 3 ----------------------
SIST ETS 300 474-2:1999
Page 2
ETS 300 474-2: August 1996
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.
---------------------- Page: 4 ----------------------
SIST ETS 300 474-2:1999
Page 3
ETS 300 474-2: August 1996
Contents
Foreword .5
1 Scope .7
2 Normative references.7
3 Definitions abbreviations .8
3.1 Definitions .8
3.2 Abbreviations .8
4 Conformance requirement concerning profile ICS.8
Annex A (normative): Requirement lists for DECT FT .9
A.1 General.9
A.1.1 Profile Requirement List (profile RL).9
A.1.2 General conditions.10
A.2 Network layer - FT: profile Requirement List (profile RL).10
A.2.1 Major capabilities .10
A.2.1.1 Entities.10
A.2.1.2 CC features .11
A.2.1.3 MM features .12
A.2.1.4 SS features (services).13
A.2.1.5 LCE features .14
A.2.1.6 Procedures.14
A.2.2 Messages.16
A.2.2.1 Call control messages.16
A.2.2.2 Mobility management messages.22
A.2.2.3 Connection-related and connection independent supplement service
messages.27
A.2.2.4 Link control entity messages.27
A.2.3 Information elements .28
A.2.3.1 Fixed length information element support .28
A.2.3.2 Variable length information element supported.29
A.2.3.3 Escape information elements support.33
A.2.4 Protocol error handling.33
A.3 Data link control layer - FT: profile ICS .33
A.3.1 Capabilities .33
A.3.1.1 Services.33
A.3.1.1.1 C-plane services.34
A.3.1.1.2 U-plane services.34
A.3.1.1.3 Management services .34
A.3.1.2 Procedures.35
A.3.1.2.1 Generic signalling procedures .35
A.3.1.2.2 Class A procedures .35
A.3.1.2.3 Broadcast procedures .35
A.3.1.2.4 LU1 procedures .35
A.3.1.2.5 Management procedures.36
A.3.1.3 Parameters.36
A.3.1.3.1 LU1 parameters.36
A.3.1.4 Messages.37
A.3.1.4.1 C-plane PDUs.37
A.4 Medium access control layer - FT: profile ICS .37
---------------------- Page: 5 ----------------------
SIST ETS 300 474-2:1999
Page 4
ETS 300 474-2: August 1996
A.4.1 Major Capabilities. 37
A.4.1.1 Services . 37
A.4.1.1.1 Connection oriented control services. 37
A.4.1.1.2 Broadcast control services. 38
A.4.1.1.3 Multiplexing services. 38
A.4.1.1.4 Management services. 39
A.4.1.2 Procedures . 39
A.4.1.2.1 Connection setup procedures . 39
A.4.1.2.2 Connection data transfer procedures. 39
A.4.1.2.3 Connection handover procedures. 40
A.4.1.2.4 Connection release procedures . 40
A.4.1.2.5 Broadcast procedures. 40
A.4.1.2.6 CSF multiplexing procedures. 41
A.4.1.2.7 Layer management procedures. 41
A.4.1.3 Other capabilities . 41
A.4.2 Messages. 42
A.4.2.1 A - Field . 42
A.4.2.1.1 A - field header - B-field identification . 42
A.4.2.2 A - Field Messages. 42
A.4.2.2.1 Paging tail messages supported. 42
A.4.2.2.2 P messages information type . 43
T
A.4.2.2.3 Mac control messages supported. 43
A.4.2.2.4 Broadcast and connectionless (BCL) messages . 44
A.5 Physical layer - FT: profile ICS . 44
A.5.1 Physical layer procedures . 44
Annex B (normative): GAP profile-specific ICS proforma for FT. 46
B.1 Introduction for completing the profile-specific ICS proforma. 46
B.1.1 Purposes and structure . 46
B.1.3 Instructions for completing the profile-specific ICS . 48
B.2 Identification of the implementation . 48
B.2.1 Date of statement. 48
B.2.2 Implementation Under Test (IUT) identification . 48
B.2.3 System Under Test (SUT) identification. 48
B.2.4 Product supplier . 49
B.2.5 Client identification . 49
B.2.6 Contact person identification. 49
B.3 Identification of the profile. 50
B.3.1 Defect report numbers and amendments implemented. 50
B.3.2 Addenda implemented . 50
B.4 Global statement of conformance . 50
B.5 Capabilities . 51
B.5.1 NWK profile-specific ICS proforma for FT . 51
B.5.1.1 General requirements. 51
B.5.1.2 Application features . 51
B.5.1.3 Application Procedures. 51
B.5.1.4 Management procedures. 51
B.5.2 DLC profile-specific ICS proforma for FT. 52
B.5.2.1 Services . 52
B.5.3 MAC profile-specific ICS proforma for FT. 52
B.5.3.1 Services . 52
B.5.3.1.1 Extended frequency allocation service. 52
B.5.4 PH Profile-specific ICS proforma for FT. 52
B.5.4.1 Requirements . 52
History. 53
---------------------- Page: 6 ----------------------
SIST ETS 300 474-2:1999
Page 5
ETS 300 474-2: August 1996
Foreword
This European Telecommunication Standard (ETS) has been produced by the Radio Equipment and
Systems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).
This European Telecommunication Standard (ETS) has been produced by the Radio Equipment and
Systems (RES), Technical Committee of the European Telecommunications Standards Institute (ETSI).
The DECT Generic Access Profile (GAP) profile requirement list and profile-specific Implementation
Conformance Statement (ICS) proforma standard comprises two parts as follows:
Part 1: "Portable radio Termination (PT)".
Part 2: "Fixed radio Termination (FT)".
Annex A contains the requirement lists for the FT GAP.
Annex B contains the profile-specific ICS proforma for the FT GAP.
Transposition dates
Date of adoption of this ETS: 16 August 1996
Date of latest announcement of this ETS (doa): 30 November 1996
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 May 1997
Date of withdrawal of any conflicting National Standard (dow): 31 May 1997
---------------------- Page: 7 ----------------------
SIST ETS 300 474-2:1999
Page 6
ETS 300 474-2: August 1996
blank page
---------------------- Page: 8 ----------------------
SIST ETS 300 474-2:1999
Page 7
ETS 300 474-2: August 1996
1 Scope
This European Telecommunication Standard (ETS) provides the profile requirment list and profile-specific
Implementation Conformance Statement (profile ICS) proforma for the Digital Enhanced Cordless
Telecommunications (DECT) Generic Accesss Profile (GAP) at the Fixed radio Termination (FT) as
defined in ETS 300 444 [2] in compliance with the relevant requirements and in accordance with the
relevant guidance given in ISO/IEC 9646-7 [8].
The supplier of an implementation which is claimed to conform to ETS 300 444 [2] is required to complete
a copy of the Protocol Implementation Conformance Statement (PICS) proforma ETS 300 476 parts 4, 5,
6 and 7 [3], [4], [5] and [6] with the replacements from annex A of this standard, as well as, a copy of the
and profile-specific ICS proforma provided in the annex B of this standard.
2 Normative references
This ETS incorporates, by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies.
[1] ETS 300 175-5: "Radio Equipment and Systems Digital Enhanced Cordless
Telecommunications Common Interface Part 5: Network Layer".
[2] ETS 300 444: "Radio Equipment and Systems (RES) Digital European Corldless
Telecommunications (DECT): Generic Access Profile (GAP)”.
[3] ETS 300 476-4: "Radio Equipment and Systems; Digital Enhanced Cordless
Telecommunications (DECT), Common Interface, Protocol Implementation
Conformance Statement (PICS) proforma, Network layer - Fixed Termination
(FT)".
[4] ETS 300 476-5: "Radio Equipment and Systems; Digital Enhanced Cordless
Telecommunications (DECT), Common Interface, Protocol Implementation
Conformance Statement (PICS) proforma, Data Link Control layer - Fixed
Termination (FT)".
[5] ETS 300 476-6: "Radio Equipment and Systems; Digital Enhanced Cordless
Telecommunications (DECT), Common Interface, Protocol Implementation
Conformance Statement (PICS) proforma, Medium Access Control layer - Fixed
Termination (FT)".
[6] ETS 300 476-7: "Radio Equipment and Systems; Digital Enhanced Cordless
Telecommunications (DECT), Common Interface, Protocol Implementation
Conformance Statement (PICS) proforma, Physical layer".
[7] ISO/IEC 9646-1 (1995): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 1:
General concepts".
[8] ISO/IEC 9646-7 (1995): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 7:
Implementation Conformance Statements".
---------------------- Page: 9 ----------------------
SIST ETS 300 474-2:1999
Page 8
ETS 300 474-2: August 1996
3 Definitions abbreviations
3.1 Definitions
For the purposes of this ETS, the following terms and definitions apply:
a) the terms defined in ISO/IEC 9646-7 [8];
b) the definitions in ETS 300 444 [2]; and
c) the following terms defined in ISO/IEC 9646-1 [7]:
- PICS proforma;
- profile Implementation Conformance Statement (profile ICS).
3.2 Abbreviations
For the purposes of this ETS, the abbreviations defined in ISO/IEC 9646-1 [7] and ETS 300 444 [2] apply.
4 Conformance requirement concerning profile ICS
The supplier of a protocol implementation which is claimed to conform to the portable termination specific
requirements of ETS 300 444 [2] shall verify that his protocol implementation meets the profile
Requirements Lists (RLs) for each DECT protocol layer, contained in annex A of this standard, and shall
complete a copy of the profile-specific ICS proforma provided in annex B and shall provide the information
necessary to identify both the supplier and the implementation.
---------------------- Page: 10 ----------------------
SIST ETS 300 474-2:1999
Page 9
ETS 300 474-2: August 1996
Annex A (normative): Requirement lists for DECT FT
A.1 General
The supplier of a protocol implementation which is claimed to conform to the portable termination specific
requirements of ETS 300 444 [2] shall verify that his particular (NWK, DLC and MAC) layer protocol
implementation meets the profile RL for this layer. For this, he shall complete a copy of the corespondong
layer PICS proforma contained in annex A of ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6] updated
with the requirements from this annex.
A.1.1 Profile Requirement List (profile RL)
The profile Requirement List (profile RL) for the NWK, DLC, MAC and PH layer as defined in this section
is based on ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6]. For every capability listed in ETS 300 476
parts 4, 5, 6 and 7 [3] [4] [5] and [6], the profile requirements are expressed by restriction upon allowed
support answers in ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6] depending on whether the
implementation is to work in Residential/Business (R/B) or Public (P) environment. The profile RL is
produced by copying selected tables from ETS 300 476 parts 4, 5, 6 and 7 [3] [4] [5] and [6], removing the
column(s) to be completed by the supplier, and adding a new set of columns giving the new profile
requirements, both in terms of the status and allowed values. The tables are referenced by preceding it
with an “[3]”, "[4]", "[5]" or "[6]" as relevant.
Profile status column
Where it has been seen as necessary two profile status columns are provided one for
Residential/Business (R/B) environment and one for Public (P) environment.
The standardized symbols for the status column are as follows:
m or M mandatory - the capability is required to be supported;
o or O optional - the capability may be supported or not;
n/a or N/A not applicable - in the given context, it is impossible to use the capability;
x or X prohibited (excluded) - there is a requirement not to use this capability in the
given context;
o.i or O.i qualified optional - for mutually exclusive or selectable options from a set. "i" is
an integer which identifies an unique group of related optional items and the
logic of their selection which is defined immediately following the table;
ci or Ci conditional - the requirement on the capability ("m", "o", "x" or "n/a") depends on
the support of other optional or conditional items. "i" is an integer identifying an
unique conditional status expression which is defined immediately following the
table or which is defined in the general condition table below;
i or I out-of-scope - this capability is outside the scope of the given specification, and
hence irrelevant and not subject to conformance testing. This status is in
particular applicable for data fields which are reserved for future use. The
structure of such fields has to be supported, but the value is undefined and thus
to be ignored.
Reference column
The reference column gives reference to ETS 300 444 [2], except where explicitly stated otherwise.
---------------------- Page: 11 ----------------------
SIST ETS 300 474-2:1999
Page 10
ETS 300 474-2: August 1996
A.1.2 General conditions
Table A.1: General condition table
Condition identifier Condition definition
NOTE A The status of the relevant item is exactly as the status of this item in
ETS 300 476 Parts 4, 5, 6 and 7 [3] [4] [5] and [6]. The item has been
included as the profile reference column include reference to the profile that
describes the item more in details.
A.2 Network layer - FT: profile Requirement List (profile RL)
A.2.1 Major capabilities
A.2.1.1 Entities
To express the profile requirements of ETS 300 444 [2], the following table indicates the change of status
for support of entities.
Table A.2: ETS 300 476-4 [3] Table A.12 Entity supported
Item Entity name Profile Profile Profile
reference status R/B status P
1 Call control (CC) 6.2 m m
2 Call Independent Supplementary Services (CISS) - i i
3 Connection oriented message services (COMS) - i i
4 ConnectionLess message services (CLMS) - i i
5 Mobility management (MM) 6.2 m m
6 Link control entity (LCE) 6.2 m m
7 Management (LLME) 13 m m
---------------------- Page: 12 ----------------------
SIST ETS 300 474-2:1999
Page 11
ETS 300 474-2: August 1996
A.2.1.2 CC features
To express the profile requirements of ETS 300 444 [2], the following table indicates the change of status
for support of NWK layer CC features.
Table A.3: ETS 300 476-4 [3] Table A.13 CC features supported
Item Call Control features Profile Profile Profile
reference status R/B status P
1 Bell off (Alerting) 6.2 m m
2 Bell on (Alerting) 6.2 m m
3 Control of supervisory tones - i i
4 Dial tone detection indication - i i
5 Dialled digits (basic) 6.2 m m
6 Dialled digits additional - i i
7 Dialling delimiter - i i
8 Dialling delimiter request - i i
9 Display control characters 6.2 o o
10 Emergency service access request - i i
11 External Handover (inter-cell) - i i
12 Fixed part/portable part capability exchange - i i
13 Go to DTMF (infinite tone length) 6.2 o o
14 Go to DTMF signalling (defined tone length) 6.2 o m
15 Go to Pulse 6.2 o o
16 Group address - i i
17 Incoming call 6.2 m m
18 Internal call 6.2 o o
19 Off hook 6.2 m m
20 On hook (full release) 6.2 m m
21 Outgoing call 6.2 m m
22 Packet mode - i i
23 Partial release 6.2 o o
24 Pause (dialling pause) 6.2 o o
25 Register recall 6.2 o o
26 Signalling of display characters 6.2 o o
27 Selection of bearer service - i i
28 Service call 6.2 o o
29 Service change - i i
---------------------- Page: 13 ----------------------
SIST ETS 300 474-2:1999
Page 12
ETS 300 474-2: August 1996
A.2.1.3 MM features
To express the profile requirements of ETS 300 444 [2], the following table indicates the change of status
for support of NWK layer MM features.
Table A.4: ETS 300 476-4 [3] Table A.14 MM features supported
Item Mobility Management features Profile Profile Profile
reference status R/B status P
1 Authentication of FT 6.2 o o
2 Authentication of PT 6.2 o m
3 Authentication of user 6.2 o o
4 Encryption activation FT initiated 6.2 o m
5 Encryption activation PT initiated 6.2 o o
6 Encryption deactivation FT initiated 6.2 o o
7 Encryption deactivation PT initiated 6.2 o o
8 Identification of PP 6.2 o o
9 Inter-operator roaming registration - i i
10 Location de-registration - i i
11 Location registration 6.2 o m
12 Multiple subscription registration 6.6 n/a n/a
13 On air key allocation 6.2 o o
14 Service class indication/assignment 6.2 o m
15 Silent polling - i i
16 Subscription registration procedure on-air 6.2 m m
17 Subscription registration user procedure with DECT -i i
authentication module
18 Subscription registration user procedures keypad (digit entry-i i
only)
19 Terminate access rights FT initiated 6.2 o o
20 Terminate access rights PT initiated - i i
21 ZAP 6.2 o o
22 MM Partial release 8.39 m m
23 Temporary identity assign - i i
---------------------- Page: 14 ----------------------
SIST ETS 300 474-2:1999
Page 13
ETS 300 474-2: August 1996
A.2.1.4 SS features (services)
To express the profile requirements of ETS 300 444 [2], the following table indicates the change of status
for support of NWK layer SS features (services).
Table A.5: ETS 300 476-4 [3] Table A.15 SS features (services) supported
Item CC(CRSS) and CISS features Ref. Profile Profile
status R/B status P
1 Advice of charge (AOC) - i i
2 Advice of tariff request - i i
3 Call Deflection (CD) - i i
4 Call Forwarding Busy (CFB) - i i
5 Call Forwarding No Reply (CFNR) - i i
6 Call Forwarding Unconditional (CFU) - i i
7 Call Waiting (CW) - i i
8 Calling Line Identification Presentation (CLIP) 6.2 o o
9 Calling Line Identification Restriction (CLIR) - i i
10 Closed User Group (CUG) - i i
11 Completion of Calls to Busy Subscriber (CCBS) - i i
12 Call Hold (CH) - i i
13 CONFerence call add-on (CONF) - i i
14 COnnected Line identification Presentation (COLP) - i i
15 COnnected Line identification Restriction (COLR) - i i
16 Control of echo control functions - i i
17 Cost information - i i
18 Credit agency public access service - i i
19 Credit public access service - i i
20 Debit public access service - i i
21 Direct Dialling In (DDI) - i i
22 Explicit Call Transfer (ECT) - i i
23 Forced re-connection of held call - i i
24 FreePHone (FPH) - i i
25 Hold call (FT to PT) - i i
26 Hold call (PT to FT) - i i
27 Indication of teleservice available request - i i
28 Indication of teleservices available - i i
29 Malicious Call Identification (MCID) - i i
30 Multiple Subscriber Number (MSN) - i i
31 On-demand (hot bill) public access service- CRSS - i i
32 Queue management - i i
33 Re-connection of held call (FT to PT) - i i
34 Re-connection of held call (PT to FT) - i i
35 Request for indication of temporary subscriber number--i i
CRSS
36 Selection of required teleservice - i i
37 Single step Call Transfer (SCT) - i i
38 Specific trunk carrier selection - i i
39 SUBaddressing (SUB) - i i
40 Terminal Portability (TP) - i i
41 Tree ParTY (3TPY) - i i
42 User to User Signalling UUS - i i
43 CISS Partial release - i i
44 Feature key - i i
45 Indication of subscriber number - i i
46 Register recall - i i
47 Specific line selection - i i
48 External handover switch - i i
---------------------- Page: 15 ----------------------
SIST ETS 300 474-2:1999
Page 14
ETS 300 474-2: August 1996
A.2.1.5 LCE features
To express the profile requirements of ETS 300 444 [2], the following table indicates the change of status
for support of NWK layer LCE features.
Table A.6: ETS 300 476-4 [3] Table A.16 LCE features supported
Item LCE features Profile Profile status Profile status
reference R/B P
1 Connection oriented Link control (Link 6.2 m m
control)
2 Connectionless oriented Link control - i i
A.2.1.6 Procedures
To express the profile requirements of ETS 300 444 [2], the following tables indicate the change of status
for support of NWK layer procedures.
Table A.7: ETS 300 476-4 [3] Table A.18 CC proc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.