ETSI TBR 010 ed.3 (1999-07)

Digital Enhanced Cordless Telecommunications (DECT); General Terminal Attachment Requirements; Telephony Applications

RTBR/DECT-000134

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Splošne zahteve za priključevanje terminala: aplikacije v telefoniji

General Information

• Status: Published
• Publication Date: 07-Jul-1999
• Technical Committee: DECT - Digital Enhanced Cordless Telecommunications (DECT)
• Current Stage: 12 - Completion
• Due Date: 03-Dec-1999
• Completion Date: 08-Jul-1999
• Mandate: T-317
• Ref Project: SIST TBR 010 E3:2004 - Digital Enhanced Cordless Telecommunications (DECT); General Terminal Attachment Requirements; Telephony Applications

Standards Content (Sample)

SLOVENSKI STANDARD
SIST TBR 010 E3:2004
01-oktober-2004
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH'(&76SORãQH]DKWHYH]D
SULNOMXþHYDQMHWHUPLQDODDSOLNDFLMHYWHOHIRQLML
Digital Enhanced Cordless Telecommunications (DECT); General Terminal Attachment
Requirements; Telephony Applications
Ta slovenski standard je istoveten z: TBR 010 Edition 3
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
SIST TBR 010 E3:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST TBR 010 E3:2004

---------------------- Page: 2 ----------------------

SIST TBR 010 E3:2004
TECHNICAL TBR 10
BASIS for July 1999
REGULATION Third Edition
Source: DECT Reference: RTBR/DECT-000134
ICS: 33.020
Key words: DECT, radio, testing, regulation
Digital Enhanced Cordless Telecommunications (DECT);
General terminal attachment requirements;
Telephony applications
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: [e-mail] - http://www.etsi.org
Tel.: [phone] - Fax: [phone]
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1999. All rights reserved.

---------------------- Page: 3 ----------------------

SIST TBR 010 E3:2004
Page 2
TBR 10: July 1999
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST TBR 010 E3:2004
Page 3
TBR 10: July 1999
Contents
Foreword . 7
1 Scope. 9
2 Normative references . 9
3 Definitions and abbreviations. 11
3.1 Definitions. 11
3.2 Abbreviations. 12
4 Interpretation of the measurement results. 13
5 General test requirements . 14
5.1 Test philosophy . 14
5.1.1 Equipment supporting an ETSI approved profile . 14
5.1.2 Equipment not supporting an ETSI approved profile . 15
5.1.3 Applicant's declaration . 15
5.2 Low noise room . 16
5.3 Lower Tester (LT). 16
5.3.1 Description . 16
5.3.2 Connections between the EUT and the LT. 16
5.3.3 Functions and abilities . 16
5.3.4 Measurement uncertainty . 16
6 General testing conditions . 16
6.1 Environment for tests .16
6.2 Power supply limitations . 17
6.3 Power source. 17
7 Speech and telephony tests. 17
7.1 Test configurations . 17
7.1.1 General . 17
7.1.2 Testing a DECT system. 17
7.1.3 Testing a separate PP or FP. 17
7.1.4 Reference FP (ReFP) and Reference PP (RePP). 18
7.1.5 Applicability of tests. 20
7.2 Digital signal level. 20
7.3 General conditions of test. 21
7.4 Ideal codec . 21
7.5 Electro-acoustical equipment . 22
7.6 Speech coding scheme . 22
7.6.1 Requirement for speech coding algorithm. 22
7.6.2 Applicant's declaration on speech coding algorithm . 22
7.6.3 Requirement for the TAP in the FP. 22
7.6.4 Applicant's declaration on the TAP in the FP. 22
7.7 PP sending frequency response. 22
7.7.1 Requirement . 22
7.7.2 Method of measurement. 23
7.8 PP receiving frequency response. 23
7.8.1 Requirement . 23
7.8.2 Method of measurement. 24
7.9 PP loudness rating . 25
7.9.1 Requirement . 25
7.9.2 Method of measurement. 25
7.9.2.1 SLR . 25
H
7.9.2.2 RLR . 25
H
7.10 User controlled volume control in the PP . 25

---------------------- Page: 5 ----------------------

SIST TBR 010 E3:2004
Page 4
TBR 10: July 1999
7.10.1 Requirement.25
7.10.2 Method of measurement .26
7.10.2.1 SLR .26
H
7.10.2.2 RLR .26
H
7.11 PP talker sidetone masking rating .26
7.11.1 Requirement.26
7.11.2 Method of measurement .26
7.12 Listener SideTone (LST).26
7.12.1 LSTR requirement.26
7.12.2 Protocol requirement for EUTs with declared noise rejection capability .26
7.12.3 Method of measurement for LSTR.27
7.12.4 Method of measurement for the protocol requirement for EUTs with
declared noise rejection capability applying to be approved separately.27
7.12.5 Applicant's declaration for the protocol requirement for EUTs applying to
be approved as a DECT system .27
7.13 Terminal Coupling Loss (TCLw) of a PP .28
7.13.1 TCLw requirement.28
7.13.2 Protocol requirement.28
7.13.3 Method of measurement for TCLw for a PP being approved separately .28
7.13.4 Method of measurement for TCLw for a PP being approved as part of a
DECT system .29
7.13.5 Method of measurement for the protocol requirement for EUTs applying
to be approved separately.29
7.13.6 Applicant's declaration for the protocol requirement for EUTs applying to
be approved as a DECT system .29
7.14 FP echo control functions with a 4-wire interface .29
7.14.1 Static requirements .29
7.14.2 Dynamic requirements .29
7.14.2.1 Minimum TCLw.29
7.14.2.2 Full TCLw.30
7.14.3 Artificial echo loss of a FP with a 4-wire interface.30
7.14.3.1 Requirement for artificial echo loss .30
7.14.3.2 Requirement for the ability to disable the artificial echo
loss .30
7.14.3.3 Method of measurement of artificial echo loss.30
7.14.3.4 Method of measurement for ability to disable artificial
echo loss.31
7.14.3.4.1 EUTs being approved as separate
items .31
7.14.3.4.2 EUTs being approved as a DECT
system with a PP having full TCLw.31
7.14.4 Echo control device of a FP with a 4-wire interface .31
7.14.4.1 Requirement for the echo control device.31
7.14.4.2 Requirement for the ability to disable the echo control
device .31
7.14.4.3 Method of measurement for the echo control device .31
7.14.4.4 Method of measurement for the ability to disable the echo
control function .32
7.14.4.4.1 EUTs being approved as separate
items .32
7.14.4.4.2 EUTs being approved as a DECT
system with a PP having full TCLw.32
7.15 Stability loss - fixed geometry .32
7.15.1 Requirement.32
7.15.2 Method of measurement .32
7.16 Stability loss variable geometry.32
7.16.1 Requirement.32
7.16.2 Method of measurement .33
7.17 Sending distortion .33
7.17.1 Requirement.33
7.17.2 Method of measurement .33
7.18 Receiving distortion.33
7.18.1 Requirement.33

---------------------- Page: 6 ----------------------

SIST TBR 010 E3:2004
Page 5
TBR 10: July 1999
7.18.2 Method of measurement. 33
7.19 Side tone distortion. 34
7.19.1 Requirement . 34
7.19.2 Method of measurement. 34
7.20 Out of band (sending). 34
7.20.1 Requirement . 34
7.20.2 Method of measurement. 34
7.21 Out of band (receiving). 34
7.21.1 Requirement . 34
7.21.2 Method of measurement. 35
7.22 Sending noise. 35
7.22.1 Requirement . 35
7.22.2 Method of measurement. 35
7.23 Sending noise (narrow band) . 35
7.23.1 Requirement . 35
7.23.2 Method of measurement. 35
7.24 Receiving noise . 35
7.24.1 Requirement . 35
7.24.2 Method of measurement. 35
7.25 Sampling frequency level (receiving). 36
7.25.1 Requirement . 36
7.25.2 Method of measurement. 36
7.26 Acoustic shock . 36
7.27 DECT network delay.36
7.27.1 Requirement . 36
7.27.2 Method of measurement. 36
7.28 PP delay . 37
7.28.1 Requirement . 37
7.28.2 Method of measurement. 38
7.29 FP delay. 39
7.29.1 Requirement . 39
7.29.2 Method of measurement. 39
7.30 Echo control at the network side . 40
7.30.1 Requirement . 40
7.30.2 Method of measurement. 40
7.30.2.1 4-wire interface. 40
7.30.2.2 Analogue 2-wire interface. 41
7.30.2.2.1 Requirement 1. 41
7.30.2.2.2 Requirement 2. 42
7.31 Variation of gain with input level-sending . 43
7.31.1 Requirement . 43
7.31.2 Method of measurement. 43
7.32 Variation of gain with input level- receiving. 43
7.32.1 Requirement . 43
7.32.2 Method of measurement. 44
7.33 Additional requirements for DECT systems provided with a 2-wire PSTN interface. 44
7.33.1 General . 44
7.33.1.1 Polarity independence. 44
7.33.1.2 Feed Conditions . 44
7.33.1.3 Power supply. 45
7.33.1.4 Volume control . 45
7.33.2 Speech performance characteristics . 45
7.33.2.1 Sensitivity/frequency response. 45
7.33.2.2 Sending and Receiving Loudness Ratings (SLR and
RLR). 45
7.33.2.3 Sidetone . 45
7.33.2.4 Distortion . 45
7.33.2.5 Linearity (variation of gain with input level). 45
7.33.2.6 Noise . 46
7.33.2.7 Instability. 46
7.33.2.8 Echo Return Loss. 46
8 Loudspeaking and handsfree telephony.46

---------------------- Page: 7 ----------------------

SIST TBR 010 E3:2004
Page 6
TBR 10: July 1999
Annex A (normative): TBR Requirements Table (TBR-RT).47
Annex B (informative): Description of the CSS .49
B.1 General.49
B.2 Test signal.49
B.3 Measurement .50
B.4 Calculation.51
Annex C (normative): Description of the cross-correlation method.53
C.1 Test signal.53
C.2 Calculation.53
Annex D (informative): Acoustic shock requirements .54
D.1 Continuous signal.54
D.2 Peak signal.54
Annex E (informative): Bibliography.55
History.56

---------------------- Page: 8 ----------------------

SIST TBR 010 E3:2004
Page 7
TBR 10: July 1999
Foreword
This Technical Basis for Regulation (TBR) has been produced by the Digital Enhanced Cordless
Telecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).
The present document has been produced by ETSI in response to a mandate from the European
Commission issued under Council Directive 83/189/EEC (replaced by 98/34/EC) laying down a procedure
for the provision of information in the field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be
published in the Official Journal of the European Communities referencing the Council Directive 98/13/EC
[32] on the approximation of the laws of the Member States concerning telecommunications terminal
equipment, including the mutual recognition of their conformity ("the TTE Directive").
Technical specifications relevant to the TTE Directive are given in annex A.
Transposition dates
Date of adoption of this TBR: 25 June 1999
Date of latest announcement of this TBR (doa): 30 September 1999
Date of endorsement of this TBR (dop/e): 31 March 2000
Date of withdrawal of any conflicting National Standard (dow): 31 March 2000

---------------------- Page: 9 ----------------------

SIST TBR 010 E3:2004
Page 8
TBR 10: July 1999
Blank page

---------------------- Page: 10 ----------------------

SIST TBR 010 E3:2004
Page 9
TBR 10: July 1999
1 Scope
The present document specifies the technical characteristics particular to telephony applications provided
by terminal equipment which is capable of connection to a public telecommunications network and which
uses Digital Enhanced Cordless Telecommunications (DECT). The cordless transmissions for such
terminal equipment operate within the frequency band 1 880 MHz - 1 900 MHz.
The objective of the present document is to ensure interworking of terminal equipment via the public
network.
The requirements in the present document apply in addition to the attachment requirements for the
appropriate public network and the TBR for DECT general attachment requirements.
The present document is applicable to simple telephony terminals as well as to the telephony function of
multi-function or multi-service terminals.
The present document includes the speech quality and transmission requirements for a 3,1 kHz telephony
teleservice.
For each requirement in the present document, a test is given, including measurement methods. The
terminal equipment may be stimulated to perform the tests by additional equipment if necessary.
The present document is not applicable to terminal equipment specially designed for the disabled (e.g.
with amplification of received speech as an aid for the hard-of-hearing).
DECT comprises two equipment elements, referred to as a Fixed Part (FP) and a Portable Part (PP). The
present document is structured to allow type approval of either a) the FP and PP together, or b) the FP
and PP as separate items. Where the DECT FP is connected to a PSTN, and there are any peculiarities in
the requirements for voice telephony, these shall be accommodated within the FP.
2 Normative references
The present document incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to the present document only when incorporated in it by amendment or revision. For undated
references the latest edition of the publication referred to applies.
[1] EN 300 175-1: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 1: Overview".
[2] EN 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 2: Physical layer (PHL)".
[3] EN 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 3: Medium Access Control (MAC) layer".
[4] EN 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 4: Data Link Control (DLC) layer".
[5] EN 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 5: Network (NWK) layer".
[6] EN 300 175-6: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 6: Identities and addressing".
[7] EN 300 175-7: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 7: Security features".
[8] EN 300 175-8: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 8: Speech coding and transmission".

---------------------- Page: 11 ----------------------

SIST TBR 010 E3:2004
Page 10
TBR 10: July 1999
[9] ETS 300 111: "Integrated Services Digital Network (ISDN); Telephony 3,1 kHz
teleservice; Service description".
[10] I-ETS 300 245-3: "Integrated Services Digital Network (ISDN); Technical
characteristics of telephony terminals; Part 3: Pulse Code Modulation (PCM)
A-law, loudspeaking and handsfree telephony".
[11] TBR 008 (1998): "Integrated Services Digital Network (ISDN); Telephony
3,1 kHz teleservice; Attachment requirements for handset terminals".
[12] ITU-T Recommendation G.101 (1996): "The transmission plan".
[13] ITU-T Recommendation G.111 (1993): "Loudness ratings (LRs) in an
international connection".
[14] ITU-T Recommendation G.122 (1993): "Influence of national systems on
stability and talker echo in international connections".
[15] CCITT Recommendation G.223 (1988): "Assumptions for the calculation of
noise on hypothetical reference circuits for telephony".
[16] CCITT Recommendation G.711 (1988): "Pulse code modulation (PCM) of voice
frequencies".
[17] ITU-T Recommendation G.712 (1996): "Transmission performance character-
istics of pulse code modulation channels".
[18] ITU-T Recommendation G.726 (1990): "40, 32, 24, 16 kbit/s adaptive differential
pulse code modulation (ADPCM)".
[19] CCITT Recommendation O.132 (1988): "Quantizing distortion measuring
equipment using a sinusoidal test signal".
[20] ITU-T Recommendation O.133 (1993): "Equipment for measuring the
performance of PCM encoders and decoders".
[21] ITU-T Recommendation P.50 (1993): "Artificial voices".
[22] ITU-T Recommendation P.51 (1996): "Artificial
...