Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Fixed pattern antennas; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

DEN/BRAN-60014

Širokopasovne neposredne komunikacije zrak-tla - Oprema, ki deluje v frekvenčnih pasovih od 1 900 MHz do 1 920 MHz in od 5 855 MHz do 5 875 MHz - Antene s fiksno karakteristiko - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument se uporablja za talne postaje, letalske postaje in antensko opremo za DA2GC (TDD). Ta dokument vsebuje zahteve, s katerimi se dokazuje, da radijska oprema učinkovito uporablja radijski spekter in tudi podpira njegovo
učinkovito uporabo, tako da ne pride do škodljivih motenj.

General Information

Status
Published
Publication Date
10-Nov-2016
Current Stage
12 - Completion
Due Date
05-Jul-2016
Completion Date
23-Jun-2016

Buy Standard

Standard
EN 303 339 V1.1.1:2016
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 303 339 V1.1.1 (2016-06) - Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Fixed pattern antennas; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
English language
37 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 339 V1.1.0 (2016-04) - Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Fixed pattern antennas; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
English language
36 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 339 V1.0.4 (2015-12) - Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Fixed pattern antennas; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
English language
36 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Broadband Direct Air-to-Ground Communications - Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands - Fixed pattern antennas - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 303 339 V1.1.1 (2016-06)SIST EN 303 339 V1.1.1:2016en01-oktober-2016SIST EN 303 339 V1.1.1:2016SLOVENSKI
STANDARD



SIST EN 303 339 V1.1.1:2016



ETSI EN 303 339 V1.1.1 (2016-06) Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Fixed pattern antennas; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 303 339 V1.1.1:2016



ETSI ETSI EN 303 339 V1.1.1 (2016-06) 2
Reference DEN/BRAN-0060014 Keywords 3G, 3GPP, aeronautical, broadband, cellular, E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE, mobile, network, radio, regulation, UMTS, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 339 V1.1.1:2016



ETSI ETSI EN 303 339 V1.1.1 (2016-06) 3 Content Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 Executive summary . 7 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 9 3.3 Abbreviations . 9 4 Technical requirements specifications . 10 4.1 Environmental profile . 10 4.2 Conformance requirements . 10 4.2.1 Introduction. 10 4.2.2 Spectrum Emission Mask . 11 4.2.2.1 Definition . 11 4.2.2.2 Limits . 11 4.2.2.3 Conformance . 11 4.2.3 Transmitter Adjacent Channel Leakage Power (1 900 MHz to 1 920 MHz) . 11 4.2.3.1 Definition . 11 4.2.3.2 Limits . 12 4.2.3.3 Conformance . 12 4.2.4 Transmitter spurious emissions and maximum unwanted emissions in the band 5,250 GHz to 5,850 GHz . 12 4.2.4.1 Definition . 12 4.2.4.2 Limits . 12 4.2.4.3 Measurement bandwidths . 12 4.2.4.4 Conformance . 12 4.2.5 Maximum output power . 13 4.2.5.1 Definition . 13 4.2.5.2 Limits - Ground Station . 13 4.2.5.3 Limits - Aircraft Station . 13 4.2.5.4 Conformance . 13 4.2.6 Altitude attenuation factor - Aircraft Station . 13 4.2.6.1 Definition . 13 4.2.6.2 Limits . 13 4.2.6.3 Conformance . 13 4.2.7 Compatibility with BFWA - Aircraft Station . 13 4.2.7.1 Definition . 13 4.2.7.2 Limits . 14 4.2.7.3 Conformance . 14 4.2.8 Receiver Minimum Sensitivity . 14 4.2.8.1 Definition . 14 4.2.8.2 Limit . 14 4.2.8.3 Conformance . 14 4.2.9 Receiver Spurious Response . 14 4.2.9.1 Definition . 14 4.2.9.2 Limit . 14 4.2.9.3 Conformance . 15 4.2.10 Receiver Adjacent Channel Selectivity. 15 SIST EN 303 339 V1.1.1:2016



ETSI ETSI EN 303 339 V1.1.1 (2016-06) 4 4.2.10.1 Definition . 15 4.2.10.2 Limit . 15 4.2.10.3 Conformance . 15 4.2.11 Receiver Intermodulation Rejection . 15 4.2.11.1 Definition . 15 4.2.11.2 Limit . 15 4.2.11.3 Conformance . 16 4.2.12 Receiver Blocking . 16 4.2.12.1 Definition . 16 4.2.12.2 Limit . 16 4.2.12.3 Conformance . 17 4.2.13 Dedicated Antennas - Radiation Pattern Envelopes . 17 4.2.13.1 Aircraft station . 17 4.2.13.2 Ground station . 18 4.2.13.2.1 Sectorial antenna . 18 4.2.13.2.2 Directional antenna . 19 4.2.13.2.3 Omnidirectional antenna. 20 4.2.13.3 Conformance . 20 4.2.14 Dedicated Antenna Gain Requirements . 20 4.2.14.1 General . 20 4.2.14.2 Antenna Maximum Gain . 21 4.2.14.3 Conformance . 21 5 Testing for compliance with technical requirements . 21 5.1 Environmental conditions for testing . 21 5.1.1 Ground and Aircraft Station Transceivers . 21 5.1.2 Ground and Aircraft Station Antennas. 21 5.2 Interpretation of the measurement results . 21 5.3 Essential radio test suites . 22 5.3.1 Introduction. 22 5.3.2 Spectrum Emission Mask . 23 5.3.2.1 Initial conditions . 23 5.3.2.2 Procedure . 23 5.3.2.3 Test requirement . 23 5.3.3 Transmitter adjacent channel leakage power ratio (ACLR) . 23 5.3.3.1 Initial conditions . 23 5.3.3.2 Procedure . 23 5.3.3.3 Test requirement . 23 5.3.4 Transmitter spurious emissions . 24 5.3.4.1 Initial conditions . 24 5.3.4.2 Procedure . 24 5.3.4.3 Test requirement . 24 5.3.5 Transmitter maximum output power. 24 5.3.5.1 Initial conditions . 24 5.3.5.2 Procedure . 24 5.3.5.3 Test requirement . 24 5.3.6 Altitude attenuation factor - Aircraft Station . 24 5.3.6.1 Initial conditions . 24 5.3.6.2 Procedure . 24 5.3.6.3 Test requirement . 25 5.3.7 Compatibility with BFWA - Aircraft Station . 25 5.3.7.1 Initial conditions . 25 5.3.7.2 Procedure . 25 5.3.7.3 Test requirement . 25 5.3.8 Receiver Minimum Sensitivity . 25 5.3.8.1 Initial conditions . 25 5.3.8.2 Procedure . 25 5.3.8.3 Test requirement . 25 5.3.9 Receiver Spurious Response . 26 5.3.9.1 Initial conditions . 26 5.3.9.2 Procedure . 26 5.3.9.3 Test requirement . 26 SIST EN 303 339 V1.1.1:2016



ETSI ETSI EN 303 339 V1.1.1 (2016-06) 5 5.3.10 Receiver Adjacent Channel Selectivity. 26 5.3.10.1 Initial conditions . 26 5.3.10.2 Procedure . 26 5.3.10.3 Test requirement . 26 5.3.11 Receiver Intermodulation Rejection . 27 5.3.11.1 Initial conditions . 27 5.3.11.2 Procedure . 27 5.3.11.3 Test requirement . 27 5.3.12 Receiver Blocking . 27 5.3.12.1 Initial conditions . 27 5.3.12.2 Procedure . 27 5.3.12.3 Test requirement . 27 5.3.13 Dedicated antennas . 27 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 28 Annex B (normative): Test specification . 30 B.1 Normal test environment . 30 B.2 RF Signals . 30 B.2.1 Bandwidth . 30 B.2.2 Channels . 30 B.3 Test Configurations . 30 B.3.1 Maximum output power, transmitter spurious emissions and operating band unwanted emissions . 30 B.3.2 Altitude Attenuation factor . 31 B.3.3 Receiver ACS, Blocking and Spurious . 31 B.3.4 Receiver Intermodulation . 32 Annex C (informative): Environmental profile specification . 33 Annex D (normative): Geographical Data . 34 D.1 Introduction . 34 D.2 Altitude determination . 34 D.3 BFWA mitigation . 34 D.4 Time currency . 34 Annex E (informative): Bibliography . 35 Annex F (informative): Change History . 36 History . 37
SIST EN 303 339 V1.1.1:2016



ETSI ETSI EN 303 339 V1.1.1 (2016-06) 6
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access Networks (BRAN). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations.
National transposition dates Date of adoption of this EN: 21 June 2016 Date of latest announcement of this EN (doa): 30 September 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2017 Date of withdrawal of any conflicting National Standard (dow): 31 March 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 303 339 V1.1.1:2016



ETSI ETSI EN 303 339 V1.1.1 (2016-06) 7 Executive summary The present document addresses the Broadband Direct Air-to-Ground Communications system based on the ETSI System Reference Document ETSI TR 103 108 [i.6]. This System Requirement document was used by the ECC, in conjunction with other contributions, to develop technology neutral ECC Decisions on the allocation of European spectrum in the frequency bands 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz. The technical requirements in the present document reflect, in part, the results of studies undertaken within the CEPT on compatibility between broadband direct air-to-ground systems and other applications op
...

ETSI EN 303 339 V1.1.1 (2016-06)






HARMONISED EUROPEAN STANDARD
Broadband Direct Air-to-Ground Communications;
Equipment operating in the 1 900 MHz to 1 920 MHz
and 5 855 MHz to 5 875 MHz frequency bands;
Fixed pattern antennas;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 303 339 V1.1.1 (2016-06)



Reference
DEN/BRAN-0060014
Keywords
3G, 3GPP, aeronautical, broadband, cellular,
E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE,
mobile, network, radio, regulation, UMTS,
WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 339 V1.1.1 (2016-06)
Content
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Executive summary . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Introduction. 10
4.2.2 Spectrum Emission Mask . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter Adjacent Channel Leakage Power (1 900 MHz to 1 920 MHz) . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 12
4.2.3.3 Conformance . 12
4.2.4 Transmitter spurious emissions and maximum unwanted emissions in the band 5,250 GHz to
5,850 GHz . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.3 Measurement bandwidths . 12
4.2.4.4 Conformance . 12
4.2.5 Maximum output power . 13
4.2.5.1 Definition . 13
4.2.5.2 Limits - Ground Station . 13
4.2.5.3 Limits - Aircraft Station . 13
4.2.5.4 Conformance . 13
4.2.6 Altitude attenuation factor - Aircraft Station . 13
4.2.6.1 Definition . 13
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 Compatibility with BFWA - Aircraft Station . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 14
4.2.7.3 Conformance . 14
4.2.8 Receiver Minimum Sensitivity . 14
4.2.8.1 Definition . 14
4.2.8.2 Limit . 14
4.2.8.3 Conformance . 14
4.2.9 Receiver Spurious Response . 14
4.2.9.1 Definition . 14
4.2.9.2 Limit . 14
4.2.9.3 Conformance . 15
4.2.10 Receiver Adjacent Channel Selectivity. 15
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 339 V1.1.1 (2016-06)
4.2.10.1 Definition . 15
4.2.10.2 Limit . 15
4.2.10.3 Conformance . 15
4.2.11 Receiver Intermodulation Rejection . 15
4.2.11.1 Definition . 15
4.2.11.2 Limit . 15
4.2.11.3 Conformance . 16
4.2.12 Receiver Blocking . 16
4.2.12.1 Definition . 16
4.2.12.2 Limit . 16
4.2.12.3 Conformance . 17
4.2.13 Dedicated Antennas - Radiation Pattern Envelopes . 17
4.2.13.1 Aircraft station . 17
4.2.13.2 Ground station . 18
4.2.13.2.1 Sectorial antenna . 18
4.2.13.2.2 Directional antenna . 19
4.2.13.2.3 Omnidirectional antenna. 20
4.2.13.3 Conformance . 20
4.2.14 Dedicated Antenna Gain Requirements . 20
4.2.14.1 General . 20
4.2.14.2 Antenna Maximum Gain . 21
4.2.14.3 Conformance . 21
5 Testing for compliance with technical requirements . 21
5.1 Environmental conditions for testing . 21
5.1.1 Ground and Aircraft Station Transceivers . 21
5.1.2 Ground and Aircraft Station Antennas. 21
5.2 Interpretation of the measurement results . 21
5.3 Essential radio test suites . 22
5.3.1 Introduction. 22
5.3.2 Spectrum Emission Mask . 23
5.3.2.1 Initial conditions . 23
5.3.2.2 Procedure . 23
5.3.2.3 Test requirement . 23
5.3.3 Transmitter adjacent channel leakage power ratio (ACLR) . 23
5.3.3.1 Initial conditions . 23
5.3.3.2 Procedure . 23
5.3.3.3 Test requirement . 23
5.3.4 Transmitter spurious emis sions . 24
5.3.4.1 Initial conditions . 24
5.3.4.2 Procedure . 24
5.3.4.3 Test requirement . 24
5.3.5 Transmitter maximum output power. 24
5.3.5.1 Initial conditions . 24
5.3.5.2 Procedure . 24
5.3.5.3 Test requirement . 24
5.3.6 Altitude attenuation factor - Aircraft Station . 24
5.3.6.1 Initial conditions . 24
5.3.6.2 Procedure . 24
5.3.6.3 Test requirement . 25
5.3.7 Compatibility with BFWA - Aircraft Station . 25
5.3.7.1 Initial conditions . 25
5.3.7.2 Procedure . 25
5.3.7.3 Test requirement . 25
5.3.8 Receiver Minimum Sensitivity . 25
5.3.8.1 Initial conditions . 25
5.3.8.2 Procedure . 25
5.3.8.3 Test requirement . 25
5.3.9 Receiver Spurious Response . 26
5.3.9.1 Initial conditions . 26
5.3.9.2 Procedure . 26
5.3.9.3 Test requirement . 26
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 339 V1.1.1 (2016-06)
5.3.10 Receiver Adjacent Channel Selectivity. 26
5.3.10.1 Initial conditions . 26
5.3.10.2 Procedure . 26
5.3.10.3 Test requirement . 26
5.3.11 Receiver Intermodulation Rejection . 27
5.3.11.1 Initial conditions . 27
5.3.11.2 Procedure . 27
5.3.11.3 Test requirement . 27
5.3.12 Receiver Blocking . 27
5.3.12.1 Initial conditions . 27
5.3.12.2 Procedure . 27
5.3.12.3 Test requirement . 27
5.3.13 Dedicated antennas . 27
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (normative): Test specification . 30
B.1 Normal test environment . 30
B.2 RF Signals . 30
B.2.1 Bandwidth . 30
B.2.2 Channels . 30
B.3 Test Configurations . 30
B.3.1 Maximum output power, transmitter spurious emissions and operating band unwanted emissions . 30
B.3.2 Altitude Attenuation factor . 31
B.3.3 Receiver ACS, Blocking and Spurious . 31
B.3.4 Receiver Intermodulation . 32
Annex C (informative): Environmental profile specification . 33
Annex D (normative): Geographical Data . 34
D.1 Introduction . 34
D.2 Altitude determination . 34
D.3 BFWA mitigation . 34
D.4 Time currency . 34
Annex E (informative): Bibliography . 35
Annex F (informative): Change History . 36
History . 37


ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 303 339 V1.1.1 (2016-06)

Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

National transposition dates
Date of adoption of this EN: 21 June 2016
Date of latest announcement of this EN (doa): 30 September 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2017
Date of withdrawal of any conflicting National Standard (dow): 31 March 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 303 339 V1.1.1 (2016-06)
Executive summary
The present document addresses the Broadband Direct Air-to-Ground Communications system based on the ETSI
System Reference Document ETSI TR 103 108 [i.6]. This System Requirement document was used by the ECC, in
conjunction with other contributions, to develop technology neutral ECC Decisions on the allocation of European
spectrum in the frequency bands 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz.
The technical requirements in the present document reflect, in part, the results of studies undertaken within the CEPT
on compatibility between broadband direct air-to-ground systems and other applications operating within, or adjacent
to, the frequency bands that are designated for Broadband DA2GC operations.
Introduction
The technical requirements in the present document reflect, in part, the results of studies undertaken within the CEPT
on compatibilit
...

Final draft ETSI EN 303 339 V1.1.0 (2016-04)






HARMONISED EUROPEAN STANDARD
Broadband Direct Air-to-Ground Communications;
Equipment operating in the 1 900 MHz to 1 920 MHz
and 5 855 MHz to 5 875 MHz frequency bands;
Fixed pattern antennas;
Harmonised Standard covering the essential requirements of
article 3.2 of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 339 V1.1.0 (2016-04)



Reference
DEN/BRAN-0060014
Keywords
3G, 3GPP, aeronautical, broadband, cellular,
E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE,
mobile, network, radio, regulation, UMTS,
WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 339 V1.1.0 (2016-04)
Content
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Executive summary . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Introduction. 10
4.2.2 Spectrum Emission Mask . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter Adjacent Channel Leakage Power (1 900 MHz to 1 920 MHz) . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
4.2.4 Transmitter spurious emissions and maximum unwanted emissions in the band 5,250 GHz to
5,850 GHz . 11
4.2.4.1 Definition . 11
4.2.4.2 Limits . 12
4.2.4.3 Measurement bandwidths . 12
4.2.4.4 Conformance . 12
4.2.5 Maximum output power . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits - Ground Station . 12
4.2.5.3 Limits - Aircraft Station . 12
4.2.5.4 Conformance . 12
4.2.6 Altitude attenuation factor - Aircraft Station . 12
4.2.6.1 Definition . 12
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 Compatibility with BFWA - Aircraft Station . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 13
4.2.8 Receiver Minimum Sensitivity . 13
4.2.8.1 Definition . 13
4.2.8.2 Limit . 13
4.2.8.3 Conformance . 14
4.2.9 Receiver Spurious Response . 14
4.2.9.1 Definition . 14
4.2.9.2 Limit . 14
4.2.9.3 Conformance . 14
4.2.10 Receiver Adjacent Channel Selectivity. 14
4.2.10.1 Definition . 14
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 339 V1.1.0 (2016-04)
4.2.10.2 Limit . 14
4.2.10.3 Conformance . 14
4.2.11 Receiver Intermodulation Rejection . 15
4.2.11.1 Definition . 15
4.2.11.2 Limit . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver Blocking . 15
4.2.12.1 Definition . 15
4.2.12.2 Limit . 16
4.2.12.3 Conformance . 16
4.2.13 Dedicated Antennas - Radiation Pattern Envelopes . 16
4.2.13.1 Aircraft station . 16
4.2.13.2 Ground station . 17
4.2.13.2.1 Sectorial antenna . 17
4.2.13.2.2 Directional antenna . 18
4.2.13.2.3 Omnidirectional antenna. 19
4.2.13.3 Conformance . 20
4.2.14 Dedicated Antenna Gain Requirements . 20
4.2.14.1 General . 20
4.2.14.2 Antenna Maximum Gain . 20
4.2.14.3 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.1.1 Ground and Aircraft Station Transceivers . 20
5.1.2 Ground and Aircraft Station Antennas. 21
5.2 Interpretation of the measurement results . 21
5.3 Essential radio test suites . 22
5.3.1 Introduction. 22
5.3.2 Spectrum Emission Mask . 22
5.3.2.1 Initial conditions . 22
5.3.2.2 Procedure . 22
5.3.2.3 Test requirement . 22
5.3.3 Transmitter adjacent channel leakage power ratio (ACLR) . 22
5.3.3.1 Initial conditions . 22
5.3.3.2 Procedure . 23
5.3.3.3 Test requirement . 23
5.3.4 Transmitter spurious emis sions . 23
5.3.4.1 Initial conditions . 23
5.3.4.2 Procedure . 23
5.3.4.3 Test requirement . 23
5.3.5 Transmitter maximum output power. 23
5.3.5.1 Initial conditions . 23
5.3.5.2 Procedure . 23
5.3.5.3 Test requirement . 23
5.3.6 Altitude attenuation factor - Aircraft Station . 24
5.3.6.1 Initial conditions . 24
5.3.6.2 Procedure . 24
5.3.6.3 Test requirement . 24
5.3.7 Compatibility with BFWA - Aircraft Station . 24
5.3.7.1 Initial conditions . 24
5.3.7.2 Procedure . 24
5.3.7.3 Test requirement . 24
5.3.8 Receiver Minimum Sensitivity . 24
5.3.8.1 Initial conditions . 24
5.3.8.2 Procedure . 24
5.3.8.3 Test requirement . 25
5.3.9 Receiver Spurious Response . 25
5.3.9.1 Initial conditions . 25
5.3.9.2 Procedure . 25
5.3.9.3 Test requirement . 25
5.3.10 Receiver Adjacent Channel Selectivity. 25
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 339 V1.1.0 (2016-04)
5.3.10.1 Initial conditions . 25
5.3.10.2 Procedure . 25
5.3.10.3 Test requirement . 25
5.3.11 Receiver Intermodulation Rejection . 26
5.3.11.1 Initial conditions . 26
5.3.11.2 Procedure . 26
5.3.11.3 Test requirement . 26
5.3.12 Receiver Blocking . 26
5.3.12.1 Initial conditions . 26
5.3.12.2 Procedure . 26
5.3.12.3 Test requirement . 26
5.3.13 Dedicated antennas . 26
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 27
Annex B (normative): Test specification . 29
B.1 Normal test environment . 29
B.2 RF Signals . 29
B.2.1 Bandwidth . 29
B.2.2 Channels . 29
B.3 Test Configurations . 29
B.3.1 Maximum output power, transmitter spurious emissions and operating band unwanted emissions . 29
B.3.2 Altitude Attenuation factor . 30
B.3.3 Receiver ACS, Blocking and Spurious . 30
B.3.4 Receiver Intermodulation . 31
Annex C (informative): Environmental profile specification . 32
Annex D (normative): Geographical Data . 33
D.1 Introduction . 33
D.2 Altitude determination . 33
D.3 BFWA mitigation . 33
D.4 Time currency . 33
Annex E (informative): Bibliography . 34
Annex F (informative): Change History . 35
History . 36


ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 339 V1.1.0 (2016-04)

Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband
Radio Access Networks (BRAN), and is now submitted for the Vote phase of the ETSI standards EN Approval
Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Executive summary
The present document addresses the Broadband Direct Air-to-Ground Communications system based on the ETSI
System Reference Document ETSI TR 103 108 [i.6]. This System Requirement document was used by the ECC, in
conjunction with other contributions, to develop technology neutral ECC Decisions on the allocation of European
spectrum in the frequency bands 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz.
The technical requirements in the present document reflect, in part, the results of studies undertaken within the CEPT
on compatibility between broadband direct air-to-ground systems and other applications operating within, or adjacent
to, the frequency bands that are designated for Broadband DA2GC operations.
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 303 3
...

Draft ETSI EN 303 339 V1.0.4 (2015-12)






HARMONISED EUROPEAN STANDARD
Broadband Direct Air-to-Ground Communications;
Equipment operating in the 1 900 MHz to 1 920 MHz
and 5 855 MHz to 5 875 MHz frequency bands;
Fixed pattern antennas;
Harmonised Standard covering the essential requirements of
article 3.2 of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 339 V1.0.4 (2015-12)



Reference
DEN/BRAN-0060014
Keywords
3G, 3GPP, aeronautical, broadband, cellular, E-
UTRA, IMT, IMT-2000, IMT-Advanced, LTE,
mobile, network, radio, regulation, UMTS,
WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2015.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 339 V1.0.4 (2015-12)
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Executive summary . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Introduction. 10
4.2.2 Spectrum Emission Mask . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter Adjacent Channel Leakage Power (1 900 MHz to 1 920 MHz) . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
4.2.4 Transmitter spurious emis sions . 11
4.2.4.1 Definition . 11
4.2.4.2 Limits . 12
4.2.4.3 Measurement bandwidths . 12
4.2.4.4 Conformance . 12
4.2.5 Maximum output power . 12
4.2.5.1 Definition . 12
4.2.5.2 Limits - Ground Station . 12
4.2.5.3 Limits - Aircraft Station . 12
4.2.5.4 Conformance . 12
4.2.6 Altitude attenuation factor - Aircraft Station . 12
4.2.6.1 Definition . 12
4.2.6.2 Limits . 13
4.2.6.3 Conformance . 13
4.2.7 Compatibility with BFWA - Aircraft Station . 13
4.2.7.1 Definition . 13
4.2.7.2 Limits . 13
4.2.7.3 Conformance . 13
4.2.8 Receiver Minimum Sensitivity . 13
4.2.8.1 Definition . 13
4.2.8.2 Limit . 13
4.2.8.3 Conformance . 14
4.2.9 Receiver Spurious Response . 14
4.2.9.1 Definition . 14
4.2.9.2 Limit . 14
4.2.9.3 Conformance . 14
4.2.10 Receiver Adjacent Channel Selectivity. 14
4.2.10.1 Definition . 14
4.2.10.2 Limit . 14
4.2.10.3 Conformance . 14
4.2.11 Receiver Intermodulation Rejection . 15
4.2.11.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 339 V1.0.4 (2015-12)
4.2.11.2 Limit . 15
4.2.11.3 Conformance . 15
4.2.12 Receiver Blocking . 15
4.2.12.1 Definition . 15
4.2.12.2 Limit . 16
4.2.12.3 Conformance . 16
4.2.13 Dedicated Antennas - Radiation Pattern Envelopes . 16
4.2.13.1 Aircraft station . 16
4.2.13.2 Ground station . 17
4.2.13.2.1 Sectorial antenna . 17
4.2.13.2.2 Directional antenna . 18
4.2.13.2.3 Omnidirectional antenna. 19
4.2.13.3 Conformance . 19
4.2.14 Dedicated Antenna Gain Requirements . 19
4.2.14.1 General . 19
4.2.14.2 Antenna Maximum Gain . 20
4.2.14.3 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.1.1 Ground and Aircraft Station Transceivers . 20
5.1.2 Ground and Aircraft Station Antennas. 20
5.2 Interpretation of the measurement results . 20
5.3 Essential radio test suites . 22
5.3.1 Introduction. 22
5.3.2 Spectrum Emission Mask . 22
5.3.2.1 Initial conditions . 22
5.3.2.2 Procedure . 22
5.3.2.3 Test requirement . 22
5.3.3 Transmitter adjacent channel leakage power ratio (ACLR) . 22
5.3.3.1 Initial conditions . 22
5.3.3.2 Procedure . 22
5.3.3.3 Test requirement . 23
5.3.4 Transmitter spurious emis sions . 23
5.3.4.1 Initial conditions . 23
5.3.4.2 Procedure . 23
5.3.4.3 Test requirement . 23
5.3.5 Transmitter maximum output power. 23
5.3.5.1 Initial conditions . 23
5.3.5.2 Procedure . 23
5.3.5.3 Test requirement . 23
5.3.6 Altitude attenuation factor - Aircraft Station . 23
5.3.6.1 Initial conditions . 23
5.3.6.2 Procedure . 23
5.3.6.3 Test requirement . 24
5.3.7 Compatibility with BFWA - Aircraft Station . 24
5.3.7.1 Initial conditions . 24
5.3.7.2 Procedure . 24
5.3.7.3 Test requirement . 24
5.3.8 Receiver Minimum Sensitivity . 24
5.3.8.1 Initial conditions . 24
5.3.8.2 Procedure . 24
5.3.8.3 Test requirement . 24
5.3.9 Receiver Spurious Response . 24
5.3.9.1 Initial conditions . 24
5.3.9.2 Procedure . 25
5.3.9.3 Test requirement . 25
5.3.10 Receiver Adjacent Channel Selectivity. 25
5.3.10.1 Initial conditions . 25
5.3.10.2 Procedure . 25
5.3.10.3 Test requirement . 25
5.3.11 Receiver Intermodulation Rejection . 25
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 339 V1.0.4 (2015-12)
5.3.11.1 Initial conditions . 25
5.3.11.2 Procedure . 25
5.3.11.3 Test requirement . 25
5.3.12 Receiver Blocking . 26
5.3.12.1 Initial conditions . 26
5.3.12.2 Procedure . 26
5.3.12.3 Test requirement . 26
5.3.13 Dedicated antennas . 26
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 27
Annex B (normative): Test specification . 29
B.1 Normal test environment . 29
B.2 RF Signals . 29
B.2.1 Bandwidth . 29
B.2.2 Channels . 29
B.3 Test Configurations . 29
B.3.1 Maximum output power, transmitter spurious emissions and operating band unwanted emissions . 29
B.3.2 Altitude Attenuation factor . 30
B.3.3 Receiver ACS, Blocking and Spurious . 30
B.3.4 Receiver Intermodulation . 31
Annex C (informative): Environmental profile specification . 32
Annex D (normative): Geographical Data . 33
D.1 Introduction . 33
D.2 Altitude determination . 33
D.3 BFWA mitigation . 33
D.4 Time currency . 33
Annex E (informative): Bibliography . 34
Annex F (informative): Change History . 35
History . 36


ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 339 V1.0.4 (2015-12)

Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared in reply to the Commission's standardisation request Commission
Implementing Decision C(2015) 5376 final of 04.08.2015 to provide a means of conforming to the essential
requirements of Directive 2014/053/EU on the harmonisation of the laws of the Member States relating to the making
available on the market of radio equipment.
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Executive summary
The present document addresses the Broadband Direct Air-to-Ground Communications system based on the ETSI
System Reference Document ETSI TR 103 108 [i.6]. This System Requirement document was used by the ECC, in
conjunction with other contributions, to develop technology neutral ECC Decisions on the allocation of European
spectrum in the frequency bands 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz.
The technical requirements in the present document reflect, in part, the results of studies undertaken within the CEPT
on compatibility between broadband direct air-to-ground systems and other applications operating within, or adjacent
to, the frequency bands that are designated for Broadband DA2GC operations.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 339 V1.0.4 (2015-12)
Introduction
The technical requirements in the present document reflect, in part, the results of studies undertaken w
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.