ETSI TR 103 265 V1.4.1 (2019-12)

Electromagnetic compatibility and Radio spectrum Matters (ERM); Definition of radio parameters

RTR/ERM-RM-274

General Information

• Status: Published
• Publication Date: 08-Dec-2019
• Technical Committee: ERM WGRM - ERM Radio Matters
• Current Stage: 12 - Completion
• Due Date: 22-Nov-2019
• Completion Date: 09-Dec-2019

Standards Content (Sample)

TECHNICAL REPORT
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Definition of radio parameters

2 ETSI TR 103 265 V1.4.1 (2019-12)

Reference
RTR/ERM-RM-274
Keywords
definitions, radio, radio measurements, radio
parameters, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI TR 103 265 V1.4.1 (2019-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 14
3.1 Terms . 14
3.2 Symbols . 16
3.3 Abbreviations . 16
4 Presentation of the methodology used in the present document . 16
4.1 Introduction . 16
4.2 TEDDI operation and its implications . 17
4.3 The program(s) - Matlab scripts . 18
4.4 Expected structure of definitions . 19
4.5 Performance of the Scripts and orders of magnitude . 19
5 Manual search and comparison of definitions . 20
5.0 General . 20
5.1 Example of sets of definitions discussed during phase 0 and phase 1 of the work on the present
document . 20
5.1.1 Adjacent Channel Rejection Ratio (ACRR) . 20
5.1.2 Adjacent channel selectivity . 20
5.1.3 Adjacent channel selectivity and desensitization . 23
5.1.4 Alternate channel selectivity and desensitization . 23
5.1.5 Adjacent signal selectivity . 23
5.1.6 AM suppression . 23
5.1.7 Blocking . 24
5.1.8 Radio receiver blocking case 1: owing to signals occurring at the same time but on other frequencies . 27
5.1.9 Radio receiver blocking case 2: owing to signals occurring at a different time . 27
5.1.10 Blocking and spurious response rejection . 27
5.1.11 Other receiver parameters, which are now in clause 3.1 . 27
5.2 Definitions copied by hand (rejected by the Scripts) . 28
5.2.0 General . 28
5.2.1 Definitions found in ETSI EN 300 113 . 28
5.2.1.0 Introduction . 28
5.2.1.1 Frequency error . 28
5.2.1.2 Transmitter power (conducted) . 28
5.2.1.2.1 Equipment measured as constant envelope angle modulation equipment . 28
5.2.1.2.2 Equipment measured as non-constant envelope modulation equipment . 28
5.2.1.3 Rated output power . 28
5.2.1.3.1 Equipment measured as constant envelope angle modulation equipment . 28
5.2.1.3.2 Equipment measured as non-constant envelope modulation equipment . 28
5.2.1.4 Effective radiated power . 29
5.2.1.5 Effective radiated power of the transmitter . 29
5.2.1.6 Adjacent channel power . 29
5.2.1.7 Alternate channel power . 29
5.2.1.8 Spurious emissions . 29
5.2.1.9 Intermodulation attenuation . 29
5.2.1.10 Transmitter attack time . 29
5.2.1.11 Transmitter release time . 29
5.2.1.12 Transient behaviour of the transmitter . 30
ETSI
4 ETSI TR 103 265 V1.4.1 (2019-12)
5.2.1.13 Transient power . 30
5.2.1.14 Maximum usable sensitivity (conducted) . 30
5.2.1.15 Error behaviour (performance). 30
5.2.1.16 Co-channel rejection . 30
5.2.1.17 Adjacent channel selectivity. 30
5.2.1.18 Spurious response rejection . 30
5.2.1.19 Intermodulation response rejection . 30
5.2.1.20 Blocking . 30
5.2.1.21 Spurious radiations . 30
5.2.1.22 Desensitization . 31
5.2.1.23 Spurious response rejection . 31
5.2.2 Definitions found in ETSI EN 300 220 . 31
5.3 Conclusions . 31
Annex A: Definitions of parameters found by hand . 32
A.0 General . 32
A.1 Parameter 1 . 32
A.2 Parameter 2 . 32
A.3 Parameter 3 . 32
A.4 Parameter 4 . 32
A.5 Parameter 5 . 32
A.6 Parameter 6 . 32
A.7 Co-channel rejection. 33
A.7.1 Co-channel rejection. 33
A.7.2 Co-channel rejection - TCH/FS . 33
A.8 DAA threshold . 34
A.9 Receiver desensitization with simultaneous transmission and reception . 34
A.10 Receiver/Bad frame indication - TCH/FS - frequency hopping and downlink DTX . 34
A.11 Receiver/Bad frame indication - TCH/HS - frequency hopping and downlink DTX . 35
A.12 Out of band gain . 35
A.13 Conducted RF immunity . 35
A.14 Reference interference level . 36
A.15 Radio receiver interference performance . 36
A.16 Interference rejection and blocking immunity . 36
A.17 Intermodulation . 36
A.17.1 Input intermodulation . 36
A.17.2 Intermodulation . 37
A.17.3 Intermodulation response rejection . 37
A.17.4 Receiver intermodulation performance . 38
A.17.5 Intermodulation attenuation. 38
A.17.6 Intermodulation rejection - speech channels . 39
A.17.7 Intermodulation spurious response attenuation . 39
A.18 Receiver/Usable receiver input level range . 40
A.19 Receiver LBT threshold . 40
A.20 Receiver LBT threshold and transmitter max on-time . 40
A.21 Receiver opening delay . 41
A.22 Sensitivity . 41
ETSI
5 ETSI TR 103 265 V1.4.1 (2019-12)
A.22.1 Average usable sensitivity (digital, field strength) . 41
A.22.2 Average usable sensitivity (field strength, data or messages) . 41
A.22.3 Average usable sensitivity (field strength, responses) . 42
A.22.4 Average usable sensitivity (field strength, speech) . 42
A.22.5 Maximum usable sensitivity . 42
A.22.6 Maximum usable sensitivity (analogue, conducted) . 44
A.22.7 Maximum usable sensitivity (analogue, field strength) . 44
A.22.8 Maximum usable sensitivity (digital, conducted) . 44
A.22.9 Maximum usable sensitivity (digital, field strength) . 45
A.22.10 Maximum usable sensitivity (responses, conducted) . 45
A.22.11 DSC receiver maximum usable sensitivity . 45
A.22.12 Receiver call sensitivity . 45
A.22.13 Receiver sensitivity . 46
A.22.14 Reference sensitivity . 46
A.22.15 Reference sensitivity - full rate data channels in multislot configuration . 46
A.22.16 Reference sensitivity - TCH/FS for MS supporting the R-GSM band . 46
A.22.17 Multipath reference sensitivity level . 47
A.22.18 Static reference sensitivity level . 47
A.23 Radio receiver reference BER and FER . 47
A.24 Single tone desensitization . 47
A.25 Spurious emissions and radiations . 48
A.25.1 Receiver conducted spurious emissions . 48
A.25.2 Conducted spurious emissions when not transmitting . 48
A.25.3 Receiver conducted spurious emissions conveyed to the antenna . 48
A.25.4 Receiver radiated spurious emissions . 49
A.25.5 Receiver spurious emissions. 49
A.25.6 Receiver spurious emissions from the receiver antenna connector . 51
A.25.7 Receiver spurious emissions (idle mode) . 52
A.25.8 Spurious emissions when the PP has no allocated transmit channel . 52
A.25.9 Receiver spurious emissions at the antenna . 52
A.25.10 Receiver cabinet radiated spurious emissions . 52
A.25.11 Unwanted emissions in the spurious domain. 52
A.25.12 Unwanted emissions, conducted . 53
A.25.13 Unwanted conducted emissions in reception . 53
A.25.14 Unwanted radiated emission. 53
A.25.15 Receiver spurious radiations. 53
A.26 Spurious response . 56
A.26.1 Spurious response and blocking immunity . 56
A.26.2 Spurious response rejection . 56
A.26.3 Spurious response rejection ratio . 57
A.26.4 Spurious response rejection (with simultaneous transmission and reception) . 57
Annex B: Results obtained by an automatic search (i.e. before analysis of the various
definitions) . 59
Annex C: Code used in the Scripts . 60
Annex D: Bibliography . 61
History . 62

ETSI
6 ETSI TR 103 265 V1.4.1 (2019-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Report (TR) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio
spectrum Matters (ERM).
Modal verbs terminology
In the present document "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be
interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Many ETSI deliverables address radio parameters. In order to make these documents easy to read and practical for the
user, the authors usually include the definitions of those parameters in the text corresponding to the appropriate clauses
following the structure provided in the published ETSI guides and skeletons. Sometimes these definitions are not exact
copies from the ETSI Terms and Definitions database "TEDDI" or from other ETSI deliverables, but are (slightly)
adapted versions.
As a result many radio parameters have several different variants of their definitions used within ETSI.
The aim of the present document is to trace all those definitions (which are usually not included in "clause 3" of the
ETSI deliverables).
It may be possible, then, to try and harmonize them (work to be done in a later "phase").
Because there are many ETSI deliverables it is a large amount of work to find all the definitions by hand. Therefore, a
computer program that searches for definitions in ETSI deliverables has been written. The goal of this program is to
assist tracing the definitions found outside of "clause 3". The program can be found in annex C.
In the present document the results of searches by hand (see clause 5 and annex A) and automatic searches (see
annex B) co-exist to make comparisons and verifications more easy.
ETSI
7 ETSI TR 103 265 V1.4.1 (2019-12)
Practical experience has shown that some of the outputs provided by a computer program, when versions 1.1.1 and
1.1.2 of the present document had been prepared needed some further editing by hand. Therefore, in order to prepare
version 1.2.1 of the present document another set of programmes (Matlab scripts) was written. For version 1.3.1 the
scripts were enhanced. For version 1.4.1 the set of TS documents that were analysed was reduced to 3GPP TSs
addressing radio i.e. series 105, 125, 145, 136, 137 and 138 (see comment in clause B.3.1).
During a first stage of the work, ETSI deliverables of early Autumn 2016 had been used. The version 1.2.1 of the
present document used files provided by ETSI early October 2017. In version 1.3.1 a further set of deliverables of 2018
was used. In version 1.3.1 a further set of deliverables of 2018 was used. In version 1.4.1 the same set of deliverables
(2018 versions) was processed.
ETSI
8 ETSI TR 103 265 V1.4.1 (2019-12)
1 Scope
The present document is intended to provide an overview of the various definitions of radio parameters that can be
found in ETSI deliverables.
The present document includes definitions found in ETSI TRs, TSs, ESs and ENs.
As some consolidation work in the area of Radio Definitions had already been done in the early days of ETSI,
definitions in ETSI ETR 027 [i.78] and ETSI TR 100 027 [i.79] had also been searched "by program".
Older types of deliverables, such as TBRs, have not been analysed, in fine, for various reasons:
• if they had contained interesting definitions, it is likely that such definitions would also have been found in
more recent deliverables;
• their structure and layout is different from more recent ETSI deliverables and the programs (Scripts) used for
recent ETSI deliverables have difficulty to "synchronize" and find possible definitions.
2 References
2.1 Normative references
Normative references are not applicable in the present document.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
To be noted that, for practical reasons, the list below does not include the references to the ETSI TRs, TSs, ESs or ENs
that were searched by program. However, as some of the ETSI ENs have been analysed both by hand and by program,
some of the references to ENs, below, are also relevant to the searches done by program.
[i.1] ITU Radio Regulations.
[i.2] ETSI EN 301 893 (V1.4.1): "Broadband Radio Access Networks (BRAN); 5 GHz high
performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE
Directive".
[i.3] ETSI EN 302 502 (V1.2.1): "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed
broadband data transmitting systems; Harmonized EN covering the essential requirements of
article 3.2 of the R&TTE Directive".
[i.4] ETSI EN 301 406 (V1.5.1): "Digital Enhanced Cordless Telecommunications (DECT);
Harmonised Standard covering the essential requirements of article 3.2 of the Directive
2014/53/EU".
[i.5] ETSI EN 301 908-11 (V3.2.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread
(UTRA FDD) Repeaters".
ETSI
9 ETSI TR 103 265 V1.4.1 (2019-12)
[i.6] ETSI EN 302 426 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Harmonised EN for CDMA spread spectrum Repeaters operating in the 450 MHz cellular band
(CDMA450) and the 410 MHz, 450 MHz and 870 MHz PAMR bands (CDMA-PAMR) covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.7] ETSI EN 300 607-1 (V8.1.1): "Digital cellular telecommunications system (Phase 2+) (GSM);
Mobile Station (MS) conformance specification; Part 1: Conformance specification (GSM 11.10-1
version 8.1.1 Release 1999)".
[i.8] ETSI EN 300 162-1 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Radiotelephone transmitters and receivers for the maritime mobile service operating in VHF
bands; Part 1: Technical characteristics and methods of measurement".
[i.9] ETSI EN 301 025-1 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
VHF radiotelephone equipment for general communications and associated equipment for Class
"D" Digital Selective Calling (DSC); Part 1: Technical characteristics and methods of
measurement".
[i.10] ETSI EN 301 178-1 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Portable Very High Frequency (VHF) radiotelephone equipment for the maritime mobile service
operating in the VHF bands (for non-GMDSS applications only); Part 1: Technical characteristics
and methods of measurement".
[i.11] ETSI EN 300 698-1 (V1.2.1): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Radio telephone transmitters and receivers for the maritime mobile service operating in
the VHF bands used on inland waterways; Part 1: Technical characteristics and methods of
measurement".
[i.12] ETSI EN 300 720-1 (V1.2.1): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Ultra-High Frequency (UHF) on-board communications systems and equipment; Part 1:
Technical characteristics and methods of measurement".
[i.13] ETSI EN 301 929-1 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
VHF transmitters and receivers as Coast Stations for GMDSS and other applications in the
maritime mobile service; Part 1: Technical characteristics and methods of measurement".
[i.14] ETSI EN 300 086-1 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment with an internal or external RF connector intended
primarily for analogue speech; Part 1: Technical characteristics and methods of measurement".
[i.15] ETSI EN 300 296-1 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue
speech; Part 1: Technical characteristics and methods of measurement".
[i.16] ETSI EN 300 341-1 (V1.3.1): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Land Mobile Service (RP 02); Radio equipment using an integral antenna transmitting
signals to initiate a specific response in the receiver; Part 1: Technical characteristics and methods
of measurement".
[i.17] ETSI EN 300 390-1 (V1.2.1): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Land Mobile Service; Radio equipment intended for the transmission of data (and speech)
and using an integral antenna; Part 1: Technical characteristics and test conditions".
[i.18] ETSI EN 301 166-1 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment for analogue and/or digital communication (speech and/or
data) and operating on narrow band channels and having an antenna connector; Part 1: Technical
characteristics and methods of measurement".
[i.19] ETSI EN 302 561 (V2.1.1): "Land Mobile Service; Radio equipment using constant or
non-constant envelope modulation operating in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz
or 150 kHz; Harmonised Standard covering the essential requirements of article 3.2 of the
Directive 2014/53/EU".
ETSI
10 ETSI TR 103 265 V1.4.1 (2019-12)
[i.20] ETSI EN 300 113-1 (V1.6.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical
characteristics and methods of measurement".
[i.21] ETSI EN 300 761-1 (V1.2.1): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Short Range Devices (SRD); Automatic Vehicle Identification (AVI) for railways
operating in the 2,45 GHz frequency range; Part 1: Technical characteristics and methods of
measurement".
[i.22] ETSI EN 300 220-1 (V2.1.1): "Short Range Devices (SRD) operating in the frequency range
25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
[i.23] ETSI EN 300 330-1 (V1.5.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and
inductive loop systems in the frequency range 9 kHz to 30 MHz; Part 1: Technical characteristics
and test methods".
[i.24] ETSI EN 300 440-1 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 1:
Technical characteristics and test methods".
[i.25] ETSI EN 301 908-2 (V3.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 2: Harmonised EN for IMT-2000, CDMA Direct Spread (UTRA FDD) (UE)
covering essential requirements of article 3.2 of the R&TTE Directive".
[i.26] ETSI TS 125 141 (V8.4.0): "Universal Mobile Telecommunications System (UMTS); Base
Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 8.4.0 Release 8)".
[i.27] ETSI EN 301 908-3 (V3.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 3: Harmonised EN for IMT-2000, CDMA Direct Spread (UTRA FDD) (BS)
covering essential requirements of article 3.2 of the R&TTE Directive".
[i.28] ETSI EN 301 908-4 (V3.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 4: Harmonised EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (UE) covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.29] ETSI EN 301 908-5 (V3.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 5: Harmonised EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (BS) covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.30] ETSI EN 301 908-6 (V3.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 6: Harmonised EN for IMT-2000, CDMA TDD (UTRA TDD) (UE) covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.31] ETSI EN 301 908-7 (V3.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 7: Harmonised EN for IMT-2000, CDMA TDD (UTRA TDD) (BS) covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.32] ETSI EN 301 908-8 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS) and User Equipment (UE) for IMT-2000 Third-Generation cellular networks;
Part 8: Harmonised EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential
requirements of article 3.2 of the R&TTE Directive".
[i.33] ETSI EN 300 219-1 (V1.2.1): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Land Mobile Service; Radio equipment transmitting signals to initiate a specific response
in the receiver; Part 1: Technical characteristics and methods of measurement".
ETSI
11 ETSI TR 103 265 V1.4.1 (2019-12)
[i.34] ETSI EN 300 433-1 (V1.1.3): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Land Mobile Service; Double Side Band (DSB) and/or Single Side Band (SSB) amplitude
modulated citizen's band radio equipment; Part 1: Technical characteristics and methods of
measurement".
[i.35] ETSI EN 301 908-9 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS) and User Equipment (UE) for IMT-2000 Third-Generation cellular networks;
Part 9: Harmonised EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential
requirements of article 3.2 of the R&TTE Directive".
[i.36] ETSI EN 300 373-2 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Maritime mobile transmitters and receivers for use in the MF and HF bands; Part 2: Harmonised
EN covering essential requirements under article 3.2 of the R&TTE Directive".
[i.37] ETSI TS 101 087 (V8.9.0): "Digital cellular telecommunications system (Phase 2 and Phase 2+);
Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 11.21 version 8.9.0
Release 1999)".
[i.38] ETSI EN 300 392-2 (V3.2.1): "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D);
Part 2: Air Interface (AI)".
[i.39] ETSI EN 300 396-2 (V1.3.1): "Terrestrial Trunked Radio (TETRA); Technical requirements for
Direct Mode Operation (DMO); Part 2: Radio aspects".
[i.40] ETSI EN 300 396-4 (V1.3.1): "Terrestrial Trunked Radio (TETRA); Technical requirements for
Direct Mode Operation (DMO); Part 4: Type 1 repeater air interface".
[i.41] ETSI EN 300 396-7 (V1.2.1): "Terrestrial Trunked Radio (TETRA); Technical requirements for
Direct Mode Operation (DMO); Part 7: Type 2 repeater air interface".
[i.42] ETSI EN 300 396-5 (V1.2.1): "Terrestrial Trunked Radio (TETRA); Technical requirements for
Direct Mode Operation (DMO); Part 5: Gateway air interface".
[i.43] ETSI EN 301 908-10 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation
cellular networks; Part 10: Harmonised EN for IMT-2000, FDMA/TDMA (DECT) covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.44] ETSI EN 302 195-1 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Radio equipment in the frequency range 9 kHz to 315 kHz for Ultra Low Power Active Medical
Implants (ULP-AMI) and accessories; Part 1: Technical characteristics and test methods".
[i.45] ETSI EN 302 510-1 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Radio equipment in the frequency range 30 MHz to 37,5 MHz for Ultra Low Power Active
Medical Membrane Implants and Accessories; Part 1: Technical characteristics and test methods".
[i.46] ETSI EN 302 571 (V2.1.1): "Intelligent Transport Systems (ITS); Radiocommunications
equipment operating in the 5 855 MHz to 5 925 MHz frequency band; Harmonised Standard
covering the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.47] ETSI TS 151 010-1 (V4.9.0): "Digital cellular telecommunications system (Phase 2+); Mobile
Station (MS) conformance specification; Part 1: Conformance specification (3GPP TS 51.010-1
version 4.9.0 Release 4)".
[i.48] ETSI EN 300 065-1 (V1.1.3): "ElectroMagnetic Compatibility and Radio Spectrum Matters
(ERM); Narrow-band direct-printing telegraph equipment for receiving meteorological or
navigational information (NAVTEX); Part 1: Technical characteristics and methods of
measurement".
[i.49] ETSI EN 300 609-4 (V8.0.2): "Digital cellular telecommunications system (Phase 2 and Phase 2+)
(GSM); Base Station System (BSS) equipment specification; Part 4: Repeaters (GSM 11.26
version 8.0.2 Release 1999)".
ETSI
12 ETSI TR 103 265 V1.4.1 (2019-12)
[i.50] ETSI EN 301 908-12 (V3.1.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation
cellular networks; Part 12: Harmonised EN for IMT-2000, CDMA Multi-Carrier (cdma2000)
(Re
...