ETSI TR 102 436 V2.1.1 (2014-06)

Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) intended for operation in the bands 865 MHz to 868 MHz and 915 MHz to 921 MHz; Guidelines for the installation and commissioning of Radio Frequency Identification (RFID) equipment at UHF

RTR/ERM-TG34-22

General Information

• Status: Published
• Publication Date: 16-Jun-2014
• Technical Committee: ERM TG34 - ERM RF Identification Devices
• Current Stage: 12 - Completion
• Due Date: 23-Jun-2014
• Completion Date: 17-Jun-2014

Standards Content (Sample)

ETSI TR 102 436 V2.1.1 (2014-06)






Technical Report
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD) intended for operation
in the bands 865 MHz to 868 MHz and 915 MHz to 921 MHz;
Guidelines for the installation and commissioning
of Radio Frequency Identification (RFID) equipment at UHF

---------------------- Page: 1 ----------------------
2 ETSI TR 102 436 V2.1.1 (2014-06)



Reference
RTR/ERM-TG34-22
Keywords
ID, radio, short range, terrestrial
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TR 102 436 V2.1.1 (2014-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 8
4 Principles of operation. 8
4.1 Characteristics of RFID at UHF . 9
4.1.1 Antennas . 9
4.1.2 Data Rates . 10
4.1.3 Intermodulation Products . 10
4.1.4 De-tuning and absorption . 10
4.1.5 Shielding . 11
4.1.6 Transparent materials . 12
4.2 Operation in the lower and upper bands according to EN 302 208 . 12
4.2.1 Dense interrogator mode . 12
4.2.2 4 channel plan . 13
4.2.3 Benefits of band at 915 - 921 MHz . 14
4.2.4 Multiple interrogators . 14
4.2.5 Sharing the spectrum with SRDs . 14
4.2.6 Flags and the "Select" command . 15
4.2.6.1 Session Flags . 15
4.2.6.2 Selected Flag . 16
4.2.6.3 Select Command . 16
4.2.6.4 Use of flags and select commands . 16
4.2.7 Fixed and portable interrogators . 18
4.2.8 Near field systems . 18
4.3 Operation in the band 868 - 870 MHz under EN 300 220 . 18
4.3.1 Hand held readers . 19
4.3.2 Vehicle mounted interrogators . 19
4.3.3 Proximity printers . 19
4.4 CE Marking . 19
5 Preliminary considerations . 20
5.1 Acceptance Tests . 20
6 Site considerations . 20
6.1 Site survey . 20
6.2 Basic principles . 21
6.3 Antenna configurations . 21
6.4 Configurations for near field systems at UHF . 23
6.5 Tags using E.M. transmissions . 23
6.6 Near field tags . 24
6.7 Sources of interference . 24
7 Recommendations for installation . 25
7.1 Antenna fixtures . 25
7.2 Selection of antennas . 25
7.3 Positioning of the antenna . 25
ETSI

---------------------- Page: 3 ----------------------
4 ETSI TR 102 436 V2.1.1 (2014-06)
7.4 Outside antennas . 25
7.5 Antennas for GSM-R receivers . 26
7.6 Cabling . 26
7.7 Earthing (Fixed Interrogators) . 26
7.8 RFID and Short Range Devices operating within the same area . 27
8 Commissioning . 27
8.1 Setting to work . 27
8.2 Site records . 27
9 Maintenance . 27
Annex A: Conversion of units of measurement . 29
A.1 Measurements of power . 29
Annex B: Earthing systems . 30
B.1 Earth System Minimum Requirements . . 30
B.2 Typical electrode and array characteristics . 30
B.2.1 Vertical rod . 30
B.2.2 Buried ring. 31
B.2.3 Buried grid. 31
B.2.4 Measurement of soil resistivity . 31
B.3 Earthing of support structures and buildings . 33
B.3.1 Ancillary equipment external to buildings . 33
B.3.2 Metal support poles on buildings . 33
B.3.3 Metal security fences . 33
B.4 Interconnection of lightning protection systems with power supply earthing arrangements . 33
Annex C: Prefabricated portals . 34
Annex D: Commissioning procedure. 35
Annex E: Bibliography . 36
History . 37

ETSI

---------------------- Page: 4 ----------------------
5 ETSI TR 102 436 V2.1.1 (2014-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Report (TR) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio
spectrum Matters (ERM).
Every TR prepared by ETSI is voluntary. This text should be considered as guidance only and does not make the
present document mandatory.
The present document has been produced by ETSI in response to a perceived need by RFID manufacturers, installers
and end users for general guidance on the installation and commissioning of RFID systems operating at UHF.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
(Verbal forms
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TR 102 436 V2.1.1 (2014-06)
1 Scope
The present document provides recommendations to system integrators and installers on good practice for the
installation and commissioning of RFID systems operating at UHF at power levels up to 4 W e.r.p. Guidance is given
on making best use of the available spectrum as envisaged within the ETSI standard EN 302 208 [i.1]. In addition the
present document covers the use of reduced power RFID devices at UHF, such as hand held readers and proximity
printers, operating in accordance with EN 300 220 [i.2]. This includes operation in the sub-bands 869,40 - 869,65 MHz
at power levels of 500 mW and 869,7 - 870,0 MHz at power levels of 5 mW. In particular the present document
considers the practices necessary to minimize interference in situations where multiple interrogators are co-located in
close proximity. Failure to take the necessary precautions could lead to degradation in system performance. The present
document also endeavours to cover the approaches necessary to ensure that the operational requirements of the end-user
are met.
The present document concerns itself with radio matters only. It does not provide any guidance on computer hardware
and software that may be used to process the data recovered from tags.
Many of the techniques recommended in the present document have been subject to practical tests in a working
distribution centre. However each application is different and the techniques recommended in the present document
may not be applicable in all situations.
End users may wish to make use of the present document as a general guide.
The present document does not cover matters related to Health and Safety. End-users and system integrators should
familiarize themselves with the relevant national and international standards.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 302 208 (Parts 1 and 2): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz
with power levels up to 2 W".
[i.2] ETSI EN 300 220 (Parts 1 and 2): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW".
[i.3] CEPT ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)".
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TR 102 436 V2.1.1 (2014-06)
[i.4] Void.
[i.5] ISO/IEC 18000-6, Information technology - Radio frequency identification for item management -
Part 6: Parameters for air interface communications at 860 MHz to 960 MHz General.
[i.6] ETSI TS 102 902 (V1.2.1): "Electromagnetic compatibility and Radio spectrum matters (ERM);
Methods, parameters and test procedures for cognitive interference mitigation towards ER-GSM
for use by UHF RFID using Detect-And-Avoid (DAA) or other similar techniques".
[i.7] TCAM (21)36: "Passive RFID tags at the stage of placing on the market and the R&TTE
Directive".
[i.8] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
assigned frequency band: frequency band within which the device is authorized to operate
dense-interrogator mode: RFID operating mode in which multiple interrogators can transmit simultaneously in the
same channel while tags respond in the adjacent channels
frequency agile technique: technique used to determine an unoccupied sub-band in order to minimize interference
with other users of the same band
interrogator: equipment that will activate an adjacent tag and read its data
NOTE: It may also enter or modify the information in a tag.
link frequency: frequency offset of the tag backscatter with respect to the centre frequency of the interrogating signal
load: collection of tagged items that are carried on a transportable device
lower band: frequency range 865,0 - 868,0 MHz designated for use by RFID
preferred channel: channel assigned to an interrogator which, provided it is available, is selected automatically as the
channel of first choice
radiated measurements: measurements which involve the absolute measurement of a radiated field
reading range: maximum range at which a tag may be read by an interrogator
secondary channel: channels assigned to an interrogator, which is selected in the event that use of the primary
preferred channel is not possible
tag: transponder that holds data and responds to an interrogation signal
upper band: frequency range 915 - 921 MHz designated for use by RFID
3.2 Symbols
For the purposes of the present document, the following symbols apply:
dB decibel
dBm power in decibels relative to 1 mW
d distance
λ wavelength
ETSI

---------------------- Page: 7 ----------------------
8 ETSI TR 102 436 V2.1.1 (2014-06)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AFA Adaptive Frequency Agility
AM Amplitude Modulated
BCCH Broadcast Control Channel
CE Conformité Européenne
CEPT European Conference of Postal and Telecommunications Administrations
DAA Detect and Avoid
E.M. ElectroMagnetic
e.r.p. effective radiated power
ECC Electronic Communications Committee
EMC ElectroMagnetic Compatibility
EPC Electronic Product Code
ERC European Radio communication Committee
ER-GSM Extended Railways GSM
FM Frequency Modulated
GSM-R Railway GSM
LBT Listen Before Talk
PIB PolyIsoButylene
PM Phase Modulated
R&TTE Radio and Telecommunications Terminal Equipment
RCD Residual Current Devices
RF Radio Frequency
RFID Radio Frequency Identification
SNMP Simple Network Management Protocol
SRD Short Range Device
UHF Ultra High Frequency
4 Principles of operation
A basic RFID system comprises an interrogator with its associated antennas and a collection of tags. The antennas are
arranged to transmit their signal within an interrogation zone. Tags are attached to either animate or inanimate objects
that are to be identified. When a tag enters an interrogation zone, it is activated by the transmitted signal from the
interrogator. Typically the tag will respond by sending its identity and possibly some associated data. The identity and
data from the tag is validated by the receiver in the interrogator and passed to its host system. A block diagram of the
principle is shown in figure 1.
To Host
To Host
Tag Interrogator
Tag Interrogator
System
System

Figure 1: Principle of RFID
A sophisticated protocol is used to handle the transfer of data between the interrogator and tags. This ensures the
integrity of data transfer and may include error checking and correction techniques. In addition the protocol handles the
process for writing data to the tag and controls the procedure for reading multiple tags that may be present
simultaneously within the same interrogation zone.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI TR 102 436 V2.1.1 (2014-06)
Across the whole of the radio spectrum three different forms of communication are used for the transfer of information
between interrogators and tags. These are:
• Electrostatic.
• Inductive.
• Electromagnetic waves.
The present document confines itself solely to electromagnetic waves and near field techniques since they are the only
forms of communication that are relevant for RFID at UHF.
To transfer information between an interrogator and a tag it is necessary to superimpose the data on a carrier wave. This
technique is known as modulation. Various schemes are available to perform this function. They each depend on
changing one of the primary features of an alternating sinusoidal source in accordance with the transmitted data. The
most frequent choices of modulation are amplitude (AM), frequency (FM) and phase (PM).
Tags exist in a range of shapes and sizes to satisfy the particular needs of their intended application. Many tags are
passive and derive the power for their operation from the field generated by the interrogator. However some tags are
fitted with batteries, which may provide additional features (e.g. sensors) and may enable them to operate at
significantly greater ranges.
4.1 Characteristics of RFID at UHF
UHF transmission takes place by means of electromagnetic (E.M.) waves. At these frequencies E.M. waves have
properties that have many similarities to light. Transmissions travel in a straight line and the power of the received
signal is a function of the inverse square of the distance from its source. For example if the distance from a transmit
antenna is doubled the received power drops to one quarter. This property means that it is possible with UHF systems to
achieve significant reading ranges. Operation in the UHF band also makes it possible to transfer information at high
data rates. Both of these characteristics make UHF systems well suited for use in applications where tags are moving at
speed or in which there are multiple tags present in an interrogation zone.
UHF can present the installer with a number of challenges. Electromagnetic transmissions at UHF are readily reflected
from many surfaces. The reflections can cause the activation of unwanted tags and can also give rise to an effect known
as standing wave nulls. These can produce points within the interrogation zone where there are very low levels of
signal. UHF signals also experience significant levels of attenuation in the presence of water. In applications where
water may be present, system integrators should therefore make suitable provision for a reduction in reading range
during the design and configuration of the installation.
Operation is also possible using near field coupling between an interrogator and tags. This technique is useful in
situations where there are many tags in a confined area and it is necessary to control the transmitted field. Near field
systems generate magnetic fields that attenuate in accordance with the inverse cube of distance. Their properties
therefore make them useful for reading tags at close range while avoiding activation of tags outside the area of interest.
Near field techniques require the use of special antennas that are configured in the shape of a loop. Some tags have
antennas that are capable of operating with both E.M. transmissions and near field coupling.
4.1.1 Antennas
At UHF the shape of the interrogation field generated by the E.M. antennas of an interrogator will typically be in the
form of a cone. The angle subtended between the half power (or 3 dB) points of this cone is known as the beamwidth.
Often beamwidth is specified in both horizontal and vertical values, which need not necessarily be the same. In many
installations the long reading ranges possible at UHF mean that tags outside the wanted interrogation zone are
inadvertently activated. The use of antennas with a narrow beamwidth provides one means by which it is possible to
limit the area where tags may be read.
ETSI

---------------------- Page: 9 ----------------------
10 ETSI TR 102 436 V2.1.1 (2014-06)
The most common type of antenna used at UHF is the patch antenna. This typically has a beamwidth of the order of
70 degrees. The patch antenna is fully satisfactory for many short to medium range applications where there are no
other interrogators and unwanted tags in the immediate vicinity. In applications where longer reading ranges are
required it may be necessary to control the extent of the interrogation zone more precisely. A first order of improvement
may be achieved by using a variant of the standard patch antenna that is physically larger. This makes it possible to
...