Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH); Multiplexing structure

REN/TM-01063

Prenos in multipleksiranje (TM) – Sinhrona digitalna hierarhija (SDH) –Struktura multipleksiranja

General Information

Status
Published
Publication Date
24-Sep-2001
Current Stage
12 - Completion
Due Date
28-Sep-2001
Completion Date
25-Sep-2001

Buy Standard

Standard
EN 300 147 V1.4.1:2003
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Prenos in multipleksiranje (TM) – Sinhrona digitalna hierarhija (SDH) –Struktura multipleksiranjaTransmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH); Multiplexing structure33.040.20Prenosni sistemTransmission systemsICS:Ta slovenski standard je istoveten z:EN 300 147 Version 1.4.1SIST EN 300 147 V1.4.1:2003en01-december-2003SIST EN 300 147 V1.4.1:2003SLOVENSKI
STANDARD



SIST EN 300 147 V1.4.1:2003



ETSI EN 300 147 V1.4.1 (2001-09)European Standard (Telecommunications series) Transmission and Multiplexing (TM);Synchronous Digital Hierarchy (SDH);Multiplexing structure SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)2
Reference REN/TM-01063 Keywords architecture, MUX, SDH, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2001. All rights reserved.
SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)3 Contents Intellectual Property Rights.4 Foreword.4 Introduction.4 1 Scope.5 2 References.5 3 Definitions, abbreviations and conventions.5 3.1 Definitions.5 3.2 Abbreviations.5 3.3 Conventions.6 4 Basic multiplexing principles.7 5 Multiplexing method.8 6 Pointers.9 7 Overhead bytes description.10 8 Mapping of tributaries into VC-n.11 9 VC Concatenation.11 10 Statements to the annexes.12 11 Conformance testing.12 Annex A (normative): G.707 corrigendum.14 Annex B (informative): Bibliography.19 History.20
SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://www.etsi.org/legal/home.htm). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document specifies the physical and electrical characteristics of hierarchical interfaces based on IUT-T Recommendation G.707 [1] but it does not intend to preclude the use of interfaces covered in other standards. The aim of the present document is to provide inter-vendor and inter-operator compatibility. The conformance testing requirements corresponding to the specifications contained in the present document are to be specified in a different EN. Physical parameters for optical interfaces for the Synchronous Digital Hierarchy (SDH) are to be specified in a different standard which is under development.
National transposition dates Date of adoption of this EN: 21 September 2001 Date of latest announcement of this EN (doa): 31 December 2001 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2002 Date of withdrawal of any conflicting National Standard (dow): 30 June 2002
Introduction The present document is a delta document based on ITU Recommendation G.707 [1]. SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)5 1 Scope The present document specifies the hierarchical bit rates, the multiplexing structure and the mapping schemes to be used in the transmission networks based on the Synchronous Digital Hierarchy (SDH). 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-speci²fic reference, the latest version applies. [1] ITU-T Recommendation G.707 (2000): "Network node interface for the synchronous digital hierarchy (SDH)". NOTE: ITU-T Recommendation G.707 (2000) [1] contains some errors which were identified in the ITU. A corrigendum to the Recommendation [G.707 Corr.1p] [2] has been published by the ITU. Refer to annex A. [2] ITU-T Recommendation G.707 Corrigendum 1 (2001). [3] ITU-T Recommendation G.702: "Digital hierarchy bit rates". 3 Definitions, abbreviations and conventions 3.1 Definitions For the purposes of the present document, the definitions given in clause 3 of ITU-T Recommendation G.707 [1] apply. NOTE: In ITU-T Recommendation G.707 [1], clause 3.15, the number of the information bits k is wrongly defined. Refer to annex A. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AIS Alarm Indication Signal APS Automatic Protection Switching ATM Asynchronous Transfer Mode AU-n Administrative Unit-n AUG Administrative Unit Group BIP-X Bit Interleaved Parity-X CRC-N Cyclic Redundancy Check-N DCC Data Communication Channel DQDB Distributed Queue Dual Bus FDDI Fibre Distributed Data Interface FEC Forward Error Correction HDLC High-level Data Link Control MS-RDI Multiplex Section Remote Defect Indication MS-REI Multiplex Section Remote Error Indication MSF-AIS Multiplex Section FEC Alarm Indication Signal SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)6 NDF New Data Flag NNI Network Node Interface POH Path OverHead RDI Remote Defect Indication SDH Synchronous Digital Hierarchy SOH Section OverHead STM(-N) Synchronous Transport Module (-N) TU-n Tributary Unit-n TUG(-n) Tributary Unit Group (-n) VC-n Virtual Container-n 3.3 Conventions The order of transmission of information in all diagrams in ITU-T Recommendation G.707 [1] is first from left to right and then from top to bottom. Within each byte, the most significant bit is transmitted first. The most significant bit (bit 1) is illustrated at the left in all diagrams. In clauses 4 to 10, the status of each requirement is given with reference to ITU-T Recommendation G.707 [1] with the following conventions: Normative (N): Requirements with which it is necessary to comply in order to be able to claim compliance with the present document. Not Relevant (N/R): Clause (of ITU-T Recommendation G.707 [1]) is not relevant to the present document. The present document is not an equipment specification. The fact that a requirement is defined as normative does not imply that the associated function has to be implemented but means that, if implemented, the function shall be implemented in accordance with this requirement. SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)7 4 Basic multiplexing principles The basic multiplexing principles are as given in clause 6 of ITU-T Recommendation G.707 [1] together with the following statements and modifications. Table 1: Modifications and statements to clause 6 of ITU-T Recommendation G.707 [1] Clause Title Statement 6 Basic Multiplexing principles N/R 6.1 Multiplexing structure
The basic SDH multiplexing structure shall be as described in figure 1. This SDH multiplexing structure is a subset of the SDH multiplexing structure defined in the clause 6.1 of ITU-T Recommendation G.707 [1]
6.2 Basic frame structure
6.2.1 Section overhead N 6.2.2 Administrative Unit pointers N 6.2.3 Administrative Units in the STM-N N
In this clause, reference to AU-3 is N/R
6.2.4 Maintenance signals N 6.2.4.1 Alarm Indication Signals
6.2.4.1.1 MS-AIS N 6.2.4.1.2 MSF-AIS
6.2.4.1.3 AU/TU-AIS N 6.2.4.1.4 VC-AIS N 6.2.4.2 Unequipped VC-n signal
6.2.4.2.1 Case of network supporting the transport of Tandem Connection signals N 6.2.4.2.2 Case of network not supporting the transport of Tandem Connection signals N/R 6.2.4.3 Supervisory-unequipped VC-n signal
6.2.4.3.1 Case of network supporting the transport of Tandem Connection signals N 6.2.4.3.2 Case of network not supporting the transport of Tandem Connection signals N/R 6.3 Hierarchical bit rates N 6.4 Interconnection of STM-Ns N 6.5 Scrambling (see note) N 6.6 Physical specification of the NNI N NOTE: Figures 9-2 to 9-7 of ITU-T Recommendation G.707 [1] could lead to misinterpretation of the unscrambled bytes. Refer to annex A.
SIST EN 300 147 V1.4.1:2003



ETSI ETSI EN 300 147 V1.4.1 (2001-09)8 5 Multiplexing method The multiplexing method is as given in clause 7 of ITU-T Recommendation G.707 [1] together with the following statements and modifications. Table 2: Modifications and statements to clause 7 of ITU-T Recommendation G.707 [1] Clause Title Statement 7 Multiplexing method
7.1 Multiplexing of Administrative Units into STM-N
7.1.1 Multiplexing of Administrative Unit Groups (AUGs) into STM-N N 7.1.1.1 Multiplexing of AUG-N into STM-N, N=(1, 4, 16, 64, 256) N 7.1.1.2 Multiplexing of AUG-Ns into AUG-4xN N 7.1.2 Multiplexing of an AU-4 via AUG-1 N 7.1.3 Multiplexing of AU-3s via AUG-1 N/R 7.1.4 Multiplexing of AU-3 into STM-0 N 7.2 Multiplexing of Tributary Units into VC-4 and VC-3
7.2.1 Multiplexing of Tributary Unit Group-3s (TUG-3s) into a VC-4 N 7.2.2 Multiplexing of a TU-3 via TUG-3 N 7.2.3 Multiplexing of TUG-2s via a TUG-3 N 7.2.4 Multiplexing of TUG-2s into a VC-3 N/R 7.2.5 Multiplexing of a TU-2 via TUG-2s N 7.2.6 Multiplexing of TU-1s via TUG-2s N 7.3 AU-n/TU-n numbering scheme N 7.3.1 Numbering of AU-ns (VC-ns) in a STM-256 N
In this clause, reference to AU-3 is N/R
7.3.1.1 Numbering of AU-4s (VC-4s) in a STM-256 N 7.3.1.2 Numbering of AU-3s (VC-3s) in a STM-256 N/R 7.3.1.3 Numbering of AU-4-4cs (VC-4-4cs) in a STM-256 N 7.3.1.4 Numbering of AU-4-16cs (VC-4-16cs) in a STM-256 N 7.3.1.5 Numbering of AU-4-64cs (VC-4-64cs) in a STM-256 N 7.3.1.6 Numbering of an AU-4-256c in an STM-256 N 7.3.2 Numbering of AU-ns (VC-ns) in a STM-64 N
In this clause, reference to AU-3 is N/R
7.3.2.1 Numbering of AU-4s (VC-4s) in a STM-64 N 7.3.2.2 Numbering of AU-3s (VC-3s) in a STM-64 N/R 7.3.2.3 Numbering of AU-4-4cs (VC-4-4cs) in a STM-64 N 7.3.2.4 Numbering of AU-4-16cs (VC-4-16cs) in a STM-64 N 7.3.2.5 Numbering of an AU-4-64c in an STM-64 N 7.3.3 Numbering of AU-ns (VC-ns) in a STM-16 N
In this clause, reference to AU-3 is N/R
7.3.3.1 Numbering of AU-4s (VC-4s) in a STM-16 N 7.3.3.2 Numbering of AU-3s (VC-3s) in a STM-16 N/R 7.3.3.3 Numbering of AU-4-4cs (VC-4-4cs) in a STM-16 N 7.3.3.4 Numbering of AU-4-16c in an STM-16 N 7.3.4 Numbering of AU-ns (VC-ns) in a STM-4 N
In this clause, reference to AU-3 is N/R
7.3.4.1 Numbering of AU-4s (VC-4s) in a STM-4 N 7.3.4.2 Numbering of AU-3s (VC-3s) in a STM-4 N/R 7.3.4.3 Numbering of an AU-4-4c in an STM-4 N 7.3.5 Numbering of AU-4 (VC-4) in an STM-1 signal N 7.3.6 Numbering of AU-3 (VC-3) in an STM-0 signal N 7.3.7 Numbering of TU-3s in a VC-4 N 7.3.8 Numbering of TU-2s in a VC-4 N 7.3.9 Numbering of TU-12s in a VC-4 N 7.3.10 Numbering of TU-11s in a VC-4 N/R 7.3.11 Numbering of TU-2s in a VC-3 N/R 7.3.12 Numbering of TU-12s in a VC-3 N/R 7
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.