Maritime Broadband Radiolink operating within the bands 5 852 MHz to 5 872 MHz and/or 5 880 MHz to 5 900 MHz for ships and off-shore installations engaged in coordinated activities; Harmonised Standard for access to radio spectrum

REN/ERM-TGMAR-604

Pomorske širokopasovne radijske povezave, ki delujejo v pasovih od 5852 MHz do 5872 MHz in/ali od 5880 MHz do 5900 MHz, za ladje in priobalne objekte pri usklajevanju dejavnosti - Harmonizirani standard za dostop do radijskega spektra

General Information

Status
Not Published
Current Stage
12 - Citation in the OJ
Due Date
31-Oct-2022
Completion Date
20-Jul-2021

Buy Standard

Standard
EN 303 276 V1.2.1:2021
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 303 276 V1.2.1 (2021-01) - <empty>
English language
31 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 276 V1.2.0 (2020-10) - Maritime Broadband Radiolink operating within the bands 5 852 MHz to 5 872 MHz and/or 5 880 MHz to 5 900 MHz for ships and off-shore installations engaged in coordinated activities; Harmonised Standard for access to radio spectrum
English language
31 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
prEN 303 276 V1.2.0:2020
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 303 276 V1.2.1:2021
01-marec-2021
Pomorske širokopasovne radijske povezave, ki delujejo v pasovih od 5852 MHz do
5872 MHz in/ali od 5880 MHz do 5900 MHz, za ladje in priobalne objekte pri
usklajevanju dejavnosti - Harmonizirani standard za dostop do radijskega spektra
Maritime Broadband Radiolink operating within the bands 5 852 MHz to 5 872 MHz
and/or 5 880 MHz to 5 900 MHz for ships and off-shore installations engaged in
coordinated activities - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 276 V1.2.1 (2021-01)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
SIST EN 303 276 V1.2.1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 303 276 V1.2.1:2021

---------------------- Page: 2 ----------------------
SIST EN 303 276 V1.2.1:2021
ETSI EN 303 276 V1.2.1 (2021-01)






HARMONISED EUROPEAN STANDARD
Maritime Broadband Radiolink operating within the bands
5 852 MHz to 5 872 MHz and/or 5 880 MHz to 5 900 MHz for
ships and off-shore installations
engaged in coordinated activities;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
SIST EN 303 276 V1.2.1:2021
 2 ETSI EN 303 276 V1.2.1 (2021-01)



Reference
REN/ERM-TGMAR-604
Keywords
broadband, data, harmonised standard, maritime,
radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
SIST EN 303 276 V1.2.1:2021
 3 ETSI EN 303 276 V1.2.1 (2021-01)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 General and operational requirements . 8
4.2.0 General . 8
4.2.1 Construction . 8
4.2.2 Controls and indicators . 8
4.2.3 Labeling . 8
4.3 Transmitter Requirements . 9
4.3.1 Operating Frequency error . 9
4.3.1.1 Definition . 9
4.3.1.2 Method of measurement . 9
4.3.1.3 Limits . 9
4.3.2 Transmitter EIRP . 9
4.3.2.1 Definition . 9
4.3.2.2 Method of measurement . 9
4.3.2.3 Limits . 10
4.3.3 Adaptive Transmitter Power Control . 10
4.3.3.1 Definition . 10
4.3.3.2 Method of measurement . 10
4.3.3.3 Limits . 11
4.3.4 Transmitter spectrum mask . 11
4.3.4.1 Definition . 11
4.3.4.2 Method of measurement . 11
4.3.4.3 Limits . 11
4.3.5 Transmitter spurious emis sions . 12
4.3.5.1 Definition . 12
4.3.5.2 Method of measurement . 12
4.3.5.3 Limits . 13
4.4 Receiver Requirements . 13
4.4.1 Maximum usable sensitivity . 13
4.4.1.1 Definition . 13
4.4.1.2 Method of measurement . 13
4.4.1.3 Limits . 14
4.4.2 Error behaviour at high input levels (dynamic range). 14
4.4.2.1 Definition . 14
4.4.2.2 Method of measurement . 14
4.4.2.3 Limits . 14
4.4.3 Co-channel rejection . 14
4.4.3.1 Definition . 14
4.4.3.2 Method of measurement . 14
4.4.3.3 Limits . 15
4.4.4 Adjacent channel selectivity . 15
4.4.4.1 Definition . 15
ETSI

---------------------- Page: 5 ----------------------
SIST EN 303 276 V1.2.1:2021
 4 ETSI EN 303 276 V1.2.1 (2021-01)
4.4.4.2 Method of measurement . 15
4.4.4.3 Limits . 16
4.4.5 Blocking . 16
4.4.5.1 Definition . 16
4.4.5.2 Method of measurement . 16
4.4.5.3 Limits . 17
4.4.6 Receiver and Transmitter standby spurious emissions . 17
4.4.6.1 Definition . 17
4.4.6.2 Method of measurement . 17
4.4.6.3 Limits . 18
4.4.7 Receiver spurious response rejection . 18
4.4.7.1 Definition . 18
4.4.7.2 Method of measurement . 18
4.4.7.3 Limit . 20
4.4.8 Receiver radio-frequency intermodulation . 20
4.4.8.1 Definition . 20
4.4.8.2 Method of Measurement . 20
4.4.8.3 Limit . 21
5 Testing for compliance with technical requirements . 21
5.1 General conditions of measurements . 21
5.1.1 General . 21
5.1.2 Test site and general arrangements for measurements . 21
5.1.3 Test signals . 21
5.1.4 Bit error measurements . 21
5.1.5 Impedance . 22
5.1.6 Tests of equipment with a notch filter . 22
5.1.7 Facilities for access . 22
5.1.7.1 Coupling arrangements . 22
5.1.8 Modes of operation of the transmitter . 22
5.2 Environmental conditions for testing . 22
5.2.1 General Requirements . 22
5.2.2 Test conditions . 22
5.2.2.1 General . 22
5.2.2.2 Test signals . 22
5.2.2.3 Normal test conditions . 23
5.2.2.3.1 Normal temperature and humidity . 23
5.2.2.3.2 Normal power source . 23
5.2.2.3.2.1 Mains voltage and frequency . 23
5.2.2.3.2.2 Battery power source. 23
5.2.2.3.2.3 Other power sources . 23
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 24
Annex B (informative): Maximum measurement uncertainty . 26
Annex C (informative): Checklist . 27
Annex D (informative): Bibliography . 29
Annex E (informative): Change history . 30
History . 31

ETSI

---------------------- Page: 6 ----------------------
SIST EN 303 276 V1.2.1:2021
 5 ETSI EN 303 276 V1.2.1 (2021-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

National transposition dates
Date of adoption of this EN: 6 January 2021
Date of latest announcement of this EN (doa): 30 April 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2021
Date of withdrawal of any conflicting National Standard (dow): 31 October 2022

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 7 ----------------------
SIST EN 303 276 V1.2.1:2021
 6 ETSI EN 303 276 V1.2.1 (2021-01)
1 Scope
The present document specifies technical characteristics and methods of measurements for below-deck equipment for
maritime mobile broadband radiocommunication systems (MBR) radio equipment utilizing integral electronically phase
steered antennae applicable for communications between vessels and between vessels and platforms engaged in
coordinated off-shore activities and intended to operate at the frequencies shown in table 1, operating with linear
polarization or Left Hand Circular Polarization (LHCP)
Table 1: MBR operating frequencies
Operation MBR operating frequencies
Transmission 5 862 MHz, 5 890 MHz
Reception 5 862 MHz, 5 890 MHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or non-
specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.150 (05-1996) plus corrigendum 1 (05/2002): "General requirements
for instrumentation for performance measurements on digital transmission equipment".
[2] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI

---------------------- Page: 8 ----------------------
SIST EN 303 276 V1.2.1:2021
 7 ETSI EN 303 276 V1.2.1 (2021-01)
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ECC Recommendation (17)03 (2017): "Guidance for the harmonised use and coordination of
Maritime Broadband Radio (MBR) systems on board ships and off-shore platforms operating
within the frequency bands 5852-5872 MHz and 5880-5900 MHz".
[i.4] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.5] ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
[i.6] ITU Radio Regulations (2020).
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
out-of-band domain: frequency range, immediately outside the necessary bandwidth but excluding the spurious
domain
switching range: maximum frequency band within which an equipment can operate
3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Minimum number of frames
F
dB Level (dB) below carrier
c
dBm Level (dB) relative to 1 mW
dBW Level (dB) relative to 1 W
f frequency
N Number of transmitted bits
-6
ppm parts per million (10 )
s second
V Volt
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ac alternating current
ATPC Adaptive Transmitter Power Control
BER Bit Error Rate
CRC Cyclic Redundancy Check
EIRP Equivalent Isotropically Radiated Power
EUT Equipment Under Test
FER Frame Error Rate
LHCP Left Hand Circular Polarization
MBR Maritime Broadband Radiolink
NA Not Applicable
OOB Out Of Band
PTT Push To Talk
ETSI

---------------------- Page: 9 ----------------------
SIST EN 303 276 V1.2.1:2021
 8 ETSI EN 303 276 V1.2.1 (2021-01)
RBW Reference BandWidth
RF Radio Frequency
sr switching range
TDMA Time Division Multiple Access
VSWR Voltage Standing Wave Ratio
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be in accordance with its intended use, but as a minimum, shall be that specified in the test
conditions contained in the present document. The equipment shall comply with all the technical requirements of the
present document at all times when operating within the boundary limits of the operational environmental profile
defined by its intended use.
4.2 General and operational requirements
4.2.0 General
Compliance with clauses 4.2.1, clause 4.2.2 and clause 4.2.3 shall be established by simple inspection of the equipment
and its technical documentation.
4.2.1 Construction
All controls shall be of sufficient size to enable the usual control functions to be easily performed and the number of
controls should be the minimum necessary for simple and satisfactory operation. The equipment shall be capable of
operating on single frequency channels.
4.2.2 Controls and indicators
The equipment shall have a channel selector and shall indicate the channel at which the installation is set. The operating
channel shall be legible irrespective of the external lighting conditions.
The equipment shall have the following additional controls and indicators:
• an on/off switch for the entire installation with a visual indication that the installation is in operation;
• a visual indication that the equipment is transmitting.
The equipment shall also meet the following requiremen
...

ETSI EN 303 276 V1.2.1 (2021-01)






HARMONISED EUROPEAN STANDARD
Maritime Broadband Radiolink operating within the bands
5 852 MHz to 5 872 MHz and/or 5 880 MHz to 5 900 MHz for
ships and off-shore installations
engaged in coordinated activities;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 ETSI EN 303 276 V1.2.1 (2021-01)



Reference
REN/ERM-TGMAR-604
Keywords
broadband, data, harmonised standard, maritime,
radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 276 V1.2.1 (2021-01)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 General and operational requirements . 8
4.2.0 General . 8
4.2.1 Construction . 8
4.2.2 Controls and indicators . 8
4.2.3 Labeling . 8
4.3 Transmitter Requirements . 9
4.3.1 Operating Frequency error . 9
4.3.1.1 Definition . 9
4.3.1.2 Method of measurement . 9
4.3.1.3 Limits . 9
4.3.2 Transmitter EIRP . 9
4.3.2.1 Definition . 9
4.3.2.2 Method of measurement . 9
4.3.2.3 Limits . 10
4.3.3 Adaptive Transmitter Power Control . 10
4.3.3.1 Definition . 10
4.3.3.2 Method of measurement . 10
4.3.3.3 Limits . 11
4.3.4 Transmitter spectrum mask . 11
4.3.4.1 Definition . 11
4.3.4.2 Method of measurement . 11
4.3.4.3 Limits . 11
4.3.5 Transmitter spurious emis sions . 12
4.3.5.1 Definition . 12
4.3.5.2 Method of measurement . 12
4.3.5.3 Limits . 13
4.4 Receiver Requirements . 13
4.4.1 Maximum usable sensitivity . 13
4.4.1.1 Definition . 13
4.4.1.2 Method of measurement . 13
4.4.1.3 Limits . 14
4.4.2 Error behaviour at high input levels (dynamic range). 14
4.4.2.1 Definition . 14
4.4.2.2 Method of measurement . 14
4.4.2.3 Limits . 14
4.4.3 Co-channel rejection . 14
4.4.3.1 Definition . 14
4.4.3.2 Method of measurement . 14
4.4.3.3 Limits . 15
4.4.4 Adjacent channel selectivity . 15
4.4.4.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 276 V1.2.1 (2021-01)
4.4.4.2 Method of measurement . 15
4.4.4.3 Limits . 16
4.4.5 Blocking . 16
4.4.5.1 Definition . 16
4.4.5.2 Method of measurement . 16
4.4.5.3 Limits . 17
4.4.6 Receiver and Transmitter standby spurious emissions . 17
4.4.6.1 Definition . 17
4.4.6.2 Method of measurement . 17
4.4.6.3 Limits . 18
4.4.7 Receiver spurious response rejection . 18
4.4.7.1 Definition . 18
4.4.7.2 Method of measurement . 18
4.4.7.3 Limit . 20
4.4.8 Receiver radio-frequency intermodulation . 20
4.4.8.1 Definition . 20
4.4.8.2 Method of Measurement . 20
4.4.8.3 Limit . 21
5 Testing for compliance with technical requirements . 21
5.1 General conditions of measurements . 21
5.1.1 General . 21
5.1.2 Test site and general arrangements for measurements . 21
5.1.3 Test signals . 21
5.1.4 Bit error measurements . 21
5.1.5 Impedance . 22
5.1.6 Tests of equipment with a notch filter . 22
5.1.7 Facilities for access . 22
5.1.7.1 Coupling arrangements . 22
5.1.8 Modes of operation of the transmitter . 22
5.2 Environmental conditions for testing . 22
5.2.1 General Requirements . 22
5.2.2 Test conditions . 22
5.2.2.1 General . 22
5.2.2.2 Test signals . 22
5.2.2.3 Normal test conditions . 23
5.2.2.3.1 Normal temperature and humidity . 23
5.2.2.3.2 Normal power source . 23
5.2.2.3.2.1 Mains voltage and frequency . 23
5.2.2.3.2.2 Battery power source. 23
5.2.2.3.2.3 Other power sources . 23
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 24
Annex B (informative): Maximum measurement uncertainty . 26
Annex C (informative): Checklist . 27
Annex D (informative): Bibliography . 29
Annex E (informative): Change history . 30
History . 31

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 276 V1.2.1 (2021-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

National transposition dates
Date of adoption of this EN: 6 January 2021
Date of latest announcement of this EN (doa): 30 April 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2021
Date of withdrawal of any conflicting National Standard (dow): 31 October 2022

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 303 276 V1.2.1 (2021-01)
1 Scope
The present document specifies technical characteristics and methods of measurements for below-deck equipment for
maritime mobile broadband radiocommunication systems (MBR) radio equipment utilizing integral electronically phase
steered antennae applicable for communications between vessels and between vessels and platforms engaged in
coordinated off-shore activities and intended to operate at the frequencies shown in table 1, operating with linear
polarization or Left Hand Circular Polarization (LHCP)
Table 1: MBR operating frequencies
Operation MBR operating frequencies
Transmission 5 862 MHz, 5 890 MHz
Reception 5 862 MHz, 5 890 MHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or non-
specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.150 (05-1996) plus corrigendum 1 (05/2002): "General requirements
for instrumentation for performance measurements on digital transmission equipment".
[2] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 303 276 V1.2.1 (2021-01)
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ECC Recommendation (17)03 (2017): "Guidance for the harmonised use and coordination of
Maritime Broadband Radio (MBR) systems on board ships and off-shore platforms operating
within the frequency bands 5852-5872 MHz and 5880-5900 MHz".
[i.4] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.5] ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
[i.6] ITU Radio Regulations (2020).
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
out-of-band domain: frequency range, immediately outside the necessary bandwidth but excluding the spurious
domain
switching range: maximum frequency band within which an equipment can operate
3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Minimum number of frames
F
dB Level (dB) below carrier
c
dBm Level (dB) relative to 1 mW
dBW Level (dB) relative to 1 W
f frequency
N Number of transmitted bits
-6
ppm parts per million (10 )
s second
V Volt
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ac alternating current
ATPC Adaptive Transmitter Power Control
BER Bit Error Rate
CRC Cyclic Redundancy Check
EIRP Equivalent Isotropically Radiated Power
EUT Equipment Under Test
FER Frame Error Rate
LHCP Left Hand Circular Polarization
MBR Maritime Broadband Radiolink
NA Not Applicable
OOB Out Of Band
PTT Push To Talk
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 303 276 V1.2.1 (2021-01)
RBW Reference BandWidth
RF Radio Frequency
sr switching range
TDMA Time Division Multiple Access
VSWR Voltage Standing Wave Ratio
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be in accordance with its intended use, but as a minimum, shall be that specified in the test
conditions contained in the present document. The equipment shall comply with all the technical requirements of the
present document at all times when operating within the boundary limits of the operational environmental profile
defined by its intended use.
4.2 General and operational requirements
4.2.0 General
Compliance with clauses 4.2.1, clause 4.2.2 and clause 4.2.3 shall be established by simple inspection of the equipment
and its technical documentation.
4.2.1 Construction
All controls shall be of sufficient size to enable the usual control functions to be easily performed and the number of
controls should be the minimum necessary for simple and satisfactory operation. The equipment shall be capable of
operating on single frequency channels.
4.2.2 Controls and indicators
The equipment shall have a channel selector and shall indicate the channel at which the installation is set. The operating
channel shall be legible irrespective of the external lighting conditions.
The equipment shall have the following additional controls and indicators:
• an on/off switch for the entire installation with a visual indication that the installation is in operation;
• a visual indication that the equipment is transmitting.
The equipment shall also meet the following requirements:
• The user shall not have access to any control which, if wrongly set, might impair the technical characteristics
of the equipment.
4.2.3 Labeling
All controls, instruments, indicators and ports shall be clearly labelled. Details of the power supply from which the
equipment is intended to operate shall be clearly indicated on the equipment.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 303 276 V1.2.1 (2021-01)
4.3 Transmitter Requirements
4.3.1 Operating Frequency error
4.3.1.1 Definition
The frequency error is the difference between the measured carrier frequency and its nominal value.
4.3.1.2 Method of measurement
The measurement setup shall be as in Figure 1.
The MBR transmitter shall be configured to transmit on the highest frequency available in the equipment, at a normal
RF output power level using test signal 1.
The receiving test antenna shall be connected to a frequency counter.

Figure 1: Measurement set up for operating frequency error
The transmitter frequency shall be measured and noted.
4.3.1.3 Limits
The measured frequency error shall not exceed 2 ppm.
4.3.2 Transmitter EIRP
4.3.2.1 Definition
The transmitter EIRP is the maximum radiated power of the equipment with its associated antenna.
4.3.2.2 Metho
...

Draft ETSI EN 303 276 V1.2.0 (2020-10)






HARMONISED EUROPEAN STANDARD
Maritime Broadband Radiolink operating within the bands
5 852 MHz to 5 872 MHz and/or 5 880 MHz to 5 900 MHz for
ships and off-shore installations
engaged in coordinated activities;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 276 V1.2.0 (2020-10)



Reference
REN/ERM-TGMAR-604
Keywords
broadband, data, harmonised standard, maritime,
radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 276 V1.2.0 (2020-10)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 General and operational requirements . 8
4.2.0 General . 8
4.2.1 Construction . 8
4.2.2 Controls and indicators . 8
4.2.3 Labeling . 8
4.3 Transmitter Requirements . 9
4.3.1 Operating Frequency error . 9
4.3.1.1 Definition . 9
4.3.1.2 Method of measurement . 9
4.3.1.3 Limits . 9
4.3.2 Transmitter EIRP . 9
4.3.2.1 Definition . 9
4.3.2.2 Method of measurement . 9
4.3.2.3 Limits . 10
4.3.3 Adaptive Transmitter Power Control . 10
4.3.3.1 Definition . 10
4.3.3.2 Method of measurement . 10
4.3.3.3 Limits . 11
4.3.4 Transmitter spectrum mask . 11
4.3.4.1 Definition . 11
4.3.4.2 Method of measurement . 11
4.3.4.3 Limits . 11
4.3.5 Transmitter spurious emis sions . 12
4.3.5.1 Definition . 12
4.3.5.2 Method of measurement . 12
4.3.5.3 Limits . 13
4.4 Receiver Requirements . 13
4.4.1 Maximum usable sensitivity . 13
4.4.1.1 Definition . 13
4.4.1.2 Method of measurement . 13
4.4.1.3 Limits . 14
4.4.2 Error behaviour at high input levels (dynamic range). 14
4.4.2.1 Definition . 14
4.4.2.2 Method of measurement . 14
4.4.2.3 Limits . 14
4.4.3 Co-channel rejection . 14
4.4.3.1 Definition . 14
4.4.3.2 Method of measurement . 14
4.4.3.3 Limits . 15
4.4.4 Adjacent channel selectivity . 15
4.4.4.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 276 V1.2.0 (2020-10)
4.4.4.2 Method of measurement . 15
4.4.4.3 Limits . 16
4.4.5 Blocking . 16
4.4.5.1 Definition . 16
4.4.5.2 Method of measurement . 16
4.4.5.3 Limits . 17
4.4.6 Receiver and Transmitter standby spurious emissions . 17
4.4.6.1 Definition . 17
4.4.6.2 Method of measurement . 17
4.4.6.3 Limits . 18
4.4.7 Receiver spurious response rejection . 18
4.4.7.1 Definition . 18
4.4.7.2 Method of measurement . 18
4.4.7.3 Limit . 20
4.4.8 Receiver radio-frequency intermodulation . 20
4.4.8.1 Definition . 20
4.4.8.2 Method of Measurement . 20
4.4.8.3 Limit . 21
5 Testing for compliance with technical requirements . 21
5.1 General conditions of measurements . 21
5.1.1 General . 21
5.1.2 Test site and general arrangements for measurements . 21
5.1.3 Test signals . 21
5.1.4 Bit error measurements . 21
5.1.5 Impedance . 22
5.1.6 Tests of equipment with a notch filter . 22
5.1.7 Facilities for access . 22
5.1.7.1 Coupling arrangements . 22
5.1.8 Modes of operation of the transmitter . 22
5.2 Environmental conditions for testing . 22
5.2.1 General Requirements . 22
5.2.2 Test conditions . 22
5.2.2.1 General . 22
5.2.2.2 Test signals . 22
5.2.2.3 Normal test conditions . 23
5.2.2.3.1 Normal temperature and humidity . 23
5.2.2.3.2 Normal power source . 23
5.2.2.3.2.1 Mains voltage and frequency . 23
5.2.2.3.2.2 Battery power source. 23
5.2.2.3.2.3 Other power sources . 23
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 24
Annex B (informative): Maximum measurement uncertainty . 26
Annex C (informative): Checklist . 27
Annex D (informative): Bibliography . 29
Annex E (informative): Change history . 30
History . 31

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 276 V1.2.0 (2020-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 276 V1.2.0 (2020-10)
1 Scope
The present document specifies technical characteristics and methods of measurements for below-deck equipment for
maritime mobile broadband radiocommunication systems (MBR) radio equipment utilizing integral electronically phase
steered antennae applicable for communications between vessels and between vessels and platforms engaged in
coordinated off-shore activities and intended to operate at the frequencies shown in table 1, operating with linear
polarization or Left Hand Circular Polarization (LHCP)
Table 1: MBR operating frequencies
Operation MBR operating frequencies
Transmission 5 862 MHz, 5 890 MHz
Reception 5 862 MHz, 5 890 MHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or non-
specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.150 (05-1996) plus corrigendum 1 (05/2002): "General requirements
for instrumentation for performance measurements on digital transmission equipment".
[2] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 276 V1.2.0 (2020-10)
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ECC Recommendation (17)03 (2017): "Guidance for the harmonised use and coordination of
Maritime Broadband Radio (MBR) systems on board ships and off-shore platforms operating
within the frequency bands 5852-5872 MHz and 5880-5900 MHz".
[i.4] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.5] ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
[i.6] ITU Radio Regulations (2020).
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
out-of-band domain: frequency range, immediately outside the necessary bandwidth but excluding the spurious
domain
switching range: maximum frequency band within which an equipment can operate
3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Minimum number of frames
F
dB Level (dB) below carrier
c
dBm Level (dB) relative to 1 mW
dBW Level (dB) relative to 1 W
f frequency
N Number of transmitted bits
-6
ppm parts per million (10 )
s second
V Volt
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ac alternating current
ATPC Adaptive Transmitter Power Control
BER Bit Error Rate
CRC Cyclic Redundancy Check
EIRP Equivalent Isotropically Radiated Power
EUT Equipment Under Test
FER Frame Error Rate
LHCP Left Hand Circular Polarization
MBR Maritime Broadband Radiolink
NA Not Applicable
OOB Out Of Band
PTT Push To Talk
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 276 V1.2.0 (2020-10)
RBW Reference BandWidth
RF Radio Frequency
sr switching range
TDMA Time Division Multiple Access
VSWR Voltage Standing Wave Ratio
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be in accordance with its intended use, but as a minimum, shall be that specified in the test
conditions contained in the present document. The equipment shall comply with all the technical requirements of the
present document at all times when operating within the boundary limits of the operational environmental profile
defined by its intended use.
4.2 General and operational requirements
4.2.0 General
Compliance with clause 4.2.1, clause 4.2.2 and clause 4.2.3 shall be established by simple inspection of the equipment
and its technical documentation.
4.2.1 Construction
All controls shall be of sufficient size to enable the usual control functions to be easily performed and the number of
controls should be the minimum necessary for simple and satisfactory operation. The equipment shall be capable of
operating on single frequency channels.
4.2.2 Controls and indicators
The equipment shall have a channel selector and shall indicate the channel at which the installation is set. The operating
channel shall be legible irrespective of the external lighting conditions.
The equipment shall have the following additional controls and indicators:
• an on/off switch for the entire installation with a visual indication that the installation is in operation;
• a visual indication that the equipment is transmitting.
The equipment shall also meet the following requirements:
• The user shall not have access to any control which, if wrongly set, might impair the technical characteristics
of the equipment.
4.2.3 Labeling
All controls, instruments, indicators and ports shall be clearly labelled. Details of the power supply from which the
equipment is intended to operate shall be clearly indicated on the equipment.
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 303 276 V1.2.0 (2020-10)
4.3 Transmitter Requirements
4.3.1 Operating Frequency error
4.3.1.1 Definition
The frequency error is the difference between the measured carrier frequency and its nominal value.
4.3.1.2 Method of measurement
The measurement setup shall be as in Figure 1.
The MBR transmitter shall be configured to transmit on the highest frequency available in the equipment, at a normal
RF output power level using test signal 1.
The receiving test antenna shall be connected to a frequency counter.

Figure 1: Measurement set up for operating frequency error
The transmitter frequency shall be measured and noted.
4.3.1.3 Limits
The measured frequency error shall not exceed 2 ppm.
...

SLOVENSKI STANDARD
oSIST prEN 303 276 V1.2.0:2020
01-december-2020
Pomorske širokopasovne radijske povezave, ki delujejo v pasovih od 5852 MHz do
5872 MHz in/ali od 5880 MHz do 5900 MHz, za ladje in priobalne objekte pri
usklajevanju dejavnosti - Harmonizirani standard za dostop do radijskega spektra
Maritime Broadband Radiolink operating within the bands 5 852 MHz to 5 872 MHz
and/or 5 880 MHz to 5 900 MHz for ships and off-shore installations engaged in
coordinated activities - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 276 V1.2.0 (2020-10)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
oSIST prEN 303 276 V1.2.0:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 303 276 V1.2.0:2020

---------------------- Page: 2 ----------------------
oSIST prEN 303 276 V1.2.0:2020
Draft ETSI EN 303 276 V1.2.0 (2020-10)






HARMONISED EUROPEAN STANDARD
Maritime Broadband Radiolink operating within the bands
5 852 MHz to 5 872 MHz and/or 5 880 MHz to 5 900 MHz for
ships and off-shore installations
engaged in coordinated activities;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 2 Draft ETSI EN 303 276 V1.2.0 (2020-10)



Reference
REN/ERM-TGMAR-604
Keywords
broadband, data, harmonised standard, maritime,
radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 3 Draft ETSI EN 303 276 V1.2.0 (2020-10)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 General and operational requirements . 8
4.2.0 General . 8
4.2.1 Construction . 8
4.2.2 Controls and indicators . 8
4.2.3 Labeling . 8
4.3 Transmitter Requirements . 9
4.3.1 Operating Frequency error . 9
4.3.1.1 Definition . 9
4.3.1.2 Method of measurement . 9
4.3.1.3 Limits . 9
4.3.2 Transmitter EIRP . 9
4.3.2.1 Definition . 9
4.3.2.2 Method of measurement . 9
4.3.2.3 Limits . 10
4.3.3 Adaptive Transmitter Power Control . 10
4.3.3.1 Definition . 10
4.3.3.2 Method of measurement . 10
4.3.3.3 Limits . 11
4.3.4 Transmitter spectrum mask . 11
4.3.4.1 Definition . 11
4.3.4.2 Method of measurement . 11
4.3.4.3 Limits . 11
4.3.5 Transmitter spurious emis sions . 12
4.3.5.1 Definition . 12
4.3.5.2 Method of measurement . 12
4.3.5.3 Limits . 13
4.4 Receiver Requirements . 13
4.4.1 Maximum usable sensitivity . 13
4.4.1.1 Definition . 13
4.4.1.2 Method of measurement . 13
4.4.1.3 Limits . 14
4.4.2 Error behaviour at high input levels (dynamic range). 14
4.4.2.1 Definition . 14
4.4.2.2 Method of measurement . 14
4.4.2.3 Limits . 14
4.4.3 Co-channel rejection . 14
4.4.3.1 Definition . 14
4.4.3.2 Method of measurement . 14
4.4.3.3 Limits . 15
4.4.4 Adjacent channel selectivity . 15
4.4.4.1 Definition . 15
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 4 Draft ETSI EN 303 276 V1.2.0 (2020-10)
4.4.4.2 Method of measurement . 15
4.4.4.3 Limits . 16
4.4.5 Blocking . 16
4.4.5.1 Definition . 16
4.4.5.2 Method of measurement . 16
4.4.5.3 Limits . 17
4.4.6 Receiver and Transmitter standby spurious emissions . 17
4.4.6.1 Definition . 17
4.4.6.2 Method of measurement . 17
4.4.6.3 Limits . 18
4.4.7 Receiver spurious response rejection . 18
4.4.7.1 Definition . 18
4.4.7.2 Method of measurement . 18
4.4.7.3 Limit . 20
4.4.8 Receiver radio-frequency intermodulation . 20
4.4.8.1 Definition . 20
4.4.8.2 Method of Measurement . 20
4.4.8.3 Limit . 21
5 Testing for compliance with technical requirements . 21
5.1 General conditions of measurements . 21
5.1.1 General . 21
5.1.2 Test site and general arrangements for measurements . 21
5.1.3 Test signals . 21
5.1.4 Bit error measurements . 21
5.1.5 Impedance . 22
5.1.6 Tests of equipment with a notch filter . 22
5.1.7 Facilities for access . 22
5.1.7.1 Coupling arrangements . 22
5.1.8 Modes of operation of the transmitter . 22
5.2 Environmental conditions for testing . 22
5.2.1 General Requirements . 22
5.2.2 Test conditions . 22
5.2.2.1 General . 22
5.2.2.2 Test signals . 22
5.2.2.3 Normal test conditions . 23
5.2.2.3.1 Normal temperature and humidity . 23
5.2.2.3.2 Normal power source . 23
5.2.2.3.2.1 Mains voltage and frequency . 23
5.2.2.3.2.2 Battery power source. 23
5.2.2.3.2.3 Other power sources . 23
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 24
Annex B (informative): Maximum measurement uncertainty . 26
Annex C (informative): Checklist . 27
Annex D (informative): Bibliography . 29
Annex E (informative): Change history . 30
History . 31

ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 5 Draft ETSI EN 303 276 V1.2.0 (2020-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 7 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 6 Draft ETSI EN 303 276 V1.2.0 (2020-10)
1 Scope
The present document specifies technical characteristics and methods of measurements for below-deck equipment for
maritime mobile broadband radiocommunication systems (MBR) radio equipment utilizing integral electronically phase
steered antennae applicable for communications between vessels and between vessels and platforms engaged in
coordinated off-shore activities and intended to operate at the frequencies shown in table 1, operating with linear
polarization or Left Hand Circular Polarization (LHCP)
Table 1: MBR operating frequencies
Operation MBR operating frequencies
Transmission 5 862 MHz, 5 890 MHz
Reception 5 862 MHz, 5 890 MHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or non-
specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.150 (05-1996) plus corrigendum 1 (05/2002): "General requirements
for instrumentation for performance measurements on digital transmission equipment".
[2] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI

---------------------- Page: 8 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 7 Draft ETSI EN 303 276 V1.2.0 (2020-10)
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ECC Recommendation (17)03 (2017): "Guidance for the harmonised use and coordination of
Maritime Broadband Radio (MBR) systems on board ships and off-shore platforms operating
within the frequency bands 5852-5872 MHz and 5880-5900 MHz".
[i.4] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.5] ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
[i.6] ITU Radio Regulations (2020).
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
out-of-band domain: frequency range, immediately outside the necessary bandwidth but excluding the spurious
domain
switching range: maximum frequency band within which an equipment can operate
3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Minimum number of frames
F
dB Level (dB) below carrier
c
dBm Level (dB) relative to 1 mW
dBW Level (dB) relative to 1 W
f frequency
N Number of transmitted bits
-6
ppm parts per million (10 )
s second
V Volt
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ac alternating current
ATPC Adaptive Transmitter Power Control
BER Bit Error Rate
CRC Cyclic Redundancy Check
EIRP Equivalent Isotropically Radiated Power
EUT Equipment Under Test
FER Frame Error Rate
LHCP Left Hand Circular Polarization
MBR Maritime Broadband Radiolink
NA Not Applicable
OOB Out Of Band
PTT Push To Talk
ETSI

---------------------- Page: 9 ----------------------
oSIST prEN 303 276 V1.2.0:2020
 8 Draft ETSI EN 303 276 V1.2.0 (2020-10)
RBW Reference BandWidth
RF Radio Frequency
sr switching range
TDMA Time Division Multiple Access
VSWR Voltage Standing Wave Ratio
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be in accordance with its intended use, but as a minimum, shall be that specified in the test
conditions contained in the present document. The equipment shall comply with all the technical requirements of the
present document at all times when operating within the boundary limits of the operational environmental profile
defined by its intended use.
4.2 General and operational requirements
4.2.0 General
Compliance with clause 4.2.1, clause 4.2.2 and clause 4.2.3 shall be established by simple inspection of the equipment
and its technical documentation.
4.2.1 Construction
All controls shall be of sufficient size to enable the usual control functions to be easily performed and the number of
controls should be the minimum necessary for simple and satisfactory operation. The equipment shall be capable of
operating on single frequency channels.
4.2.2 Controls and indicators
The equipment shall have a channel selector and shall indicate the channel at which the installation is set. The operating
channel shall be legible irrespective of the external lighting conditions.
The equipment shall have the following additional controls and indicators:
• an on/off switch for the entire instal
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.