ETSI EN 300 198 V1.5.1 (2002-07)

Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of digital signals operating at 23 GHz

REN/TM-04149-2

Fiksni radijski sistemi - Oprema tipa točka-točka - Parametri za radijske sisteme za prenos digitalnih signalov in analognih video signalov, ki delujejo v frekvenčnem območju 23 GHz

General Information

• Status: Published
• Publication Date: 16-Jul-2002
• Technical Committee: TM 4 1 - TM Point-to-Point Systems
• Current Stage: 13 - TB decision to make document historical
• Completion Date: 10-May-2007
• Ref Project: SIST EN 300 198 V1.5.1:2005 - Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of digital signals operating at 23 GHz

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 300 198 V1.5.1:2005
01-april-2005
)LNVQLUDGLMVNLVLVWHPL2SUHPDWLSDWRþNDWRþND3DUDPHWUL]DUDGLMVNHVLVWHPH]D
SUHQRVGLJLWDOQLKVLJQDORYLQDQDORJQLKYLGHRVLJQDORYNLGHOXMHMRYIUHNYHQþQHP
REPRþMX*+]
Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the
transmission of digital signals operating at 23 GHz
Ta slovenski standard je istoveten z: EN 300 198 Version 1.5.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 300 198 V1.5.1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 300 198 V1.5.1:2005

---------------------- Page: 2 ----------------------

SIST EN 300 198 V1.5.1:2005

ETSI EN 300 198 V1.5.1 (2002-07)
European Standard (Telecommunications series)


Fixed Radio Systems;
Point-to-point equipment;
Parameters for radio systems for the transmission
of digital signals operating at 23 GHz

---------------------- Page: 3 ----------------------

SIST EN 300 198 V1.5.1:2005
 2 ETSI EN 300 198 V1.5.1 (2002-07)



Reference
REN/TM-04149-2
Keywords
architecture, digital, DRRS, point-to-point, radio,
transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
[e-mail]
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2002.
All rights reserved.

TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 300 198 V1.5.1:2005
 3 ETSI EN 300 198 V1.5.1 (2002-07)
Contents
Intellectual Property Rights.5
Foreword.5
1 Scope.6
2 References.7
3 Symbols and abbreviations.9
3.1 Symbols.9
3.2 Abbreviations.9
4 General characteristics.10
4.1 Frequency bands and channel arrangements .10
4.1.1 Channel arrangements.10
4.1.2 Channel spacing for systems operating on the same route.10
4.2 Compatibility requirements between systems .11
4.3 Performance and availability requirements .11
4.4 Environmental conditions.11
4.4.1 Equipment within weather protected locations (indoor locations).11
4.4.2 Equipment for non-weather protected locations (outdoor locations).11
4.5 Power supply.11
4.6 Electromagnetic compatibility.11
4.7 System block diagram .12
4.8 Telecommunications Management Network (TMN) interface.12
4.9 Branching/feeder/antenna characteristics.12
4.9.1 Antenna radiation patterns .12
4.9.2 Antenna cross-Polar Discrimination (XPD) .12
4.9.3 Antenna Inter-Port Isolation (IPI).12
4.9.4 Waveguide flanges (or other connectors) .12
4.9.5 Return loss.13
5 System Parameters.13
5.1 Transmission capacity.13
5.2 Baseband parameters.13
5.2.1 Plesiochronous interfaces.13
5.2.2 SDH baseband interface.14
5.3 Transmitter characteristics.14
5.3.1 Transmitter power range.14
5.3.2 Transmit power and frequency control .14
5.3.2.1 Automatic Transmit Power Control (ATPC) .14
5.3.2.2 Remote Transmit Power Control (RTPC).15
5.3.2.3 Remote Frequency Control (RFC) .15
5.3.3 Transmitter output power tolerance .15
5.3.4 Transmit Local Oscillator (LO) frequency arrangements .15
5.3.5 RF spectrum mask.15
5.3.6 Discrete CW lines exceeding the spectrum mask limit.19
5.3.6.1 Spectral lines at the symbol rate.19
5.3.6.2 Other spectral lines.19
5.3.7 Spurious emissions.20
5.3.7.1 Spurious emissions - external.20
5.3.7.2 Spurious emissions - internal .21
5.3.8 Radio frequency tolerance .21
5.4 Receiver characteristics.21
5.4.1 Input level range .21
5.4.2 Receiver local oscillator frequency arrangements .21
5.4.3 Spurious emissions.21
5.4.3.1 Spurious emissions - internal .21
5.5 System performance without diversity.21
ETSI

---------------------- Page: 5 ----------------------

SIST EN 300 198 V1.5.1:2005
 4 ETSI EN 300 198 V1.5.1 (2002-07)
5.5.1 BER as a function of Receiver input Signal Level (RSL).22
5.5.2 Equipment Residual BER .22
5.5.3 Interference sensitivity.23
5.5.3.1 Co-channel interference sensitivity.23
5.5.3.2 Adjacent channel Interference.23
5.5.3.3 CW Spurious Interference.24
5.5.3.4 Front-end non-linearity requirements (two-tone CW spurious interference) .24
5.5.4 Distortion sensitivity.25
5.6 System characteristics with diversity .25
Annex A (informative): Additional information.26
A.1 Radio frequency channel arrangement .26
A.2 Feeder/antenna return loss.26
A.3 Automatic Transmit Power Control (ATPC) .27
A.4 RBER.27
A.5 Co-channel and adjacent channel interference.28
Annex B (normative): System type codes for regulatory procedures .32
Annex C (normative): Output Power Tolerance and RBER.33
Annex D (informative): Bibliography.34
History .35

ETSI

---------------------- Page: 6 ----------------------

SIST EN 300 198 V1.5.1:2005
 5 ETSI EN 300 198 V1.5.1 (2002-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission
and Multiplexing (TM).
The present document specifies the minimum performance parameters for radio equipment operating in the frequency
ranges as detailed in clause 4.1.1.
This new version modifies only class 5b spectrum mask giving more allowance for practical implementations, without
modifying any other requirements, and proposed design objectives for class 5a BER versus RSL.

National transposition dates
Date of adoption of this EN: 12 July 2002
Date of latest announcement of this EN (doa): 31 October 2002
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 April 2003
Date of withdrawal of any conflicting National Standard (dow): 30 April 2003

ETSI

---------------------- Page: 7 ----------------------

SIST EN 300 198 V1.5.1:2005
 6 ETSI EN 300 198 V1.5.1 (2002-07)
1 Scope
The present document specifies the minimum performance parameters for terrestrial digital fixed service radio
communications equipments operating in the 23 GHz frequency band and contains a complete revision in the areas of:
- additional systems with higher spectrum efficiency in the new class 4 systems;
- introduction of unique system type codes for regulatory reference to the various system types detailed in the
present document, refer to annex C and related categories of equipment classes of spectral efficiency;
- change of spectrum mask and adjacent channel selectivity of STM-0 systems in 28 MHz channel spacing to align
to EN 300 639 [32];
- introduction of new spectrum efficiency class 5 for STM-1 capacity for 28 MHz Adjacent Channel
Alternate-Polarization (ACAP as class 5a) and Adjacent Channel Co-Polarization (ACCP as class 5b),
see examples of the spectrum usage in figures 1.1a and 1.1b;

- technical specifications relevant to the EMC Directive [35], detailed in annex B.
NOTE: In EN 300 198 (V1.2.2) [36] there was provision for:
- parameters for wideband analogue systems;
- further options for digital radio systems (there referred as Grade A systems);
- specific antenna radiation patterns (now superseded by EN 300 833 [3]).
These options are not reprinted in this version as they are considered to be no longer of interest for ETSI members.
However, for regulatory purposes, they may still be referenced from EN 300 198 (V1.2.2) [36].
Digital systems are intended to be used for point-to-point connections in local and regional networks at data rates
between 2 Mbit/s and Synchronous Transport Module, level 1 (STM-1).
The parameters to be specified fall into two categories:
a) those that are required to provide compatibility between channels from different sources of equipment on the
same route, connected either:
- to separate antennas; or
- to separate polarizations of the same antenna;
b) parameters defining the transmission quality of the proposed system.
The present document deals with Radio Frequency (RF) and baseband characteristics relevant to low, medium and high
capacity Plesiochronous Digital Hierarchy (PDH) transmission systems, STM-0 and STM-1 Synchronous Digital
Hierarchy (SDH) transmission systems. Antenna/feeder system requirements are covered in EN 300 833 [3].
The present document does not contain aspects related to test procedures and test conditions however they are to be
found in EN 301 126-1 [2].
ETSI

---------------------- Page: 8 ----------------------

SIST EN 300 198 V1.5.1:2005
 7 ETSI EN 300 198 V1.5.1 (2002-07)
As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, different equipment
classes are defined:
class 2: equipment spectral efficiency based on typically 4-states modulation scheme (e.g. 4-FSK, 4-QAM,
or equivalent);
class 3: equipment spectral efficiency based on typically 8-states modulation scheme (e.g. 8 PSK, or
equivalent);
class 4: equipment spectral efficiency based on typically 16 or 32-states modulation scheme
(e.g. 16-QAM, 32-QAM, or equivalent);
class 5: equipment spectral efficiency based on typically 64-states or 128-states modulation scheme
(e.g. 64-QAM, 128-QAM, or equivalent).
The above classes are indicative only and do not imply any constraint to the actual modulation format, provided that all
the requirements in the present document are met.
Safety aspects are outside the mandate of ETSI and they will not be considered in the present document. However
compliance to EN 60950 [33] will be required to comply with Directive 1999/5/EC [34] (R&TTE).
Technical background for most of the parameters and requirements referred in the present document may be found in
TR 101 036-1 [29].
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
[1] CEPT Recommendation T/R 13-02: "Preferred channel arrangements for fixed services in the
range 22,0-29,5 GHz".
[2] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-point
equipment - Definitions, general requirements and test procedures".
[3] ETSI EN 300 833: "Fixed Radio Systems; Point-to-point Antennas; Antennas for point-to-point
fixed radio systems operating in the frequency band 3 GHz to 60 GHz".
[4] ETSI EN 300 645: "Telecommunications Management Network (TMN); Synchronous Digital
Hierarchy (SDH) radio relay equipment; Information model for use on Q interfaces".
[5] ETSI ETS 300 019 (all parts): "Equipment Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment".
[6] ETSI ETS 300 132-1: "Equipment Engineering (EE); Power supply interface at the input to
telecommunications equipment; Part 1: Operated by alternating current (ac) derived from direct
current (dc) sources".
[7] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input to
telecommunications equipment; Part 2: Operated by direct current (dc)".
[8] ETSI EN 300 385: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment".
[9] ETSI ETS 300 635: "Transmission and Multiplexing (TM); Synchronous Digital Hierarchy
(SDH); Radio specific functional blocks for transmission of M x STM-N".
ETSI

---------------------- Page: 9 ----------------------

SIST EN 300 198 V1.5.1:2005
 8 ETSI EN 300 198 V1.5.1 (2002-07)
[10] ETSI ETS 300 785: "Transmission and Multiplexing (TM); Synchronous Digital Hierarchy
(SDH); Radio specific functional blocks for transmission of M x sub-STM-1".
[11] ITU-R Recommendation F.750: "Architectures and functional aspects of radio-relay systems for
synchronous digital hierarchy (SDH)-based network".
[12] ITU-R Recommendation F.751: "Transmission characteristics and performance requirements of
radio-relay systems for SDH-based networks".
[13] ITU-R Recommendation F.1102: "Characteristics of fixed wireless systems operating in frequency
bands above about 17 GHz".
[14] ITU-R Recommendation F.1491: "Error performance objectives for real digital radio links used in
the national portion of a 27 500 km hypothetical reference path at or above the primary rate".
[15] ITU-R Recommendation F.1191: "Bandwidths and unwanted emissions of digital fixed service
systems".
[16] ITU-R Recommendation P.530: "Propagation data and prediction methods required for the design
of terrestrial line-of-sight systems".
[17] ITU-T Recommendation G.703: "Physical/electrical characteristics of hierarchical digital
interfaces".
[18] ITU-T Recommendation G.707: "Network node interface for the synchronous digital hierarchy
(SDH)".
[19] ITU-T Recommendation G.773: "Protocol suites for Q-interfaces for management of transmission
systems".
[20] ITU-T Recommendation G.708: "Sub STM-0 network node interface for the synchronous digital
hierarchy (SDH)".
[21] IEC 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for ordinary
rectangular waveguides".
[22] ITU-T Recommendation G.783: "Characteristics of synchronous digital hierarchy (SDH)
equipment functional blocks".
[23] ITU-T Recommendation G.784: "Synchronous digital hierarchy (SDH) management".
[24] ITU-T Recommendation G.826: "Error performance parameters and objectives for international,
constant bit rate digital paths at or above the primary rate".
[25] ITU-T Recommendation G.861: "Principles and guidelines for the integration of satellite and radio
systems in SDH transport networks".
[26] ITU-T Recommendation G.957: "Optical interfaces for equipments and systems relating to the
synchronous digital hierarchy".
[27] ITU-T Recommendation O.151: "Error performance measuring equipment operating at the
primary rate and above".
[28] ITU-T Recommendation O.181: "Equipment to assess error performance on STM-N interfaces".
[29] ETSI TR 101 036-1: "Fixed Radio Systems; Point-to-point equipment; Generic wordings for
standards on digital radio systems characteristics; Part 1: General aspects and point-to-point
equipment parameters".
[30] CEPT/ERC/REC 74-01: "Spurious emissions".
[31] ETSI TR 101 035: "Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH)
aspects regarding Digital Radio Relay Systems (DRRS)".
ETSI

---------------------- Page: 10 ----------------------

SIST EN 300 198 V1.5.1:2005
 9 ETSI EN 300 198 V1.5.1 (2002-07)
[32] ETSI EN 300 639: "Fixed Radio Systems; Point-to-point equipment; Sub-STM-1 digital radio
systems operating in the 13 GHz, 15 GHz and 18 GHz frequency bands with about 28 MHz
co-polar and 14 MHz cross-polar channel spacing".
[33] EN 60950: "Safety of information technology equipment".
[34] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity.
[35] Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
[36] ETSI EN 300 198 (V1.2.2): "Transmission and Multiplexing (TM); Digital Radio Relay Systems
(DRRS); Parameters for DRRS for the transmission of digital signals and analogue video signals
operating at 23 GHz".
[37] ETSI EN 301 489-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements".
[38] ETSI EN 301 489-4: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific
conditions for fixed radio links and ancillary equipment and services".
3 Symbols and abbreviations
3.1 Symbols
For the purposes of the present document, the following symbols apply:
Ω Ohm
dB decibel
dBm decibel relative to 1 mW
GHz GigaHertz
kHz kiloHertz
Mbit/s Mega-bits per second
MHz MegaHertz
mW milliWatt
ns nanosecond
ppm parts per million
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ac alternating current
ACAP Adjacent Channel Alternate Polarization
ACCP Adjacent Channel Co-Polarization
ATPC Automatic Transmit Power Control
AU Administrative Unit
BBER Background Block Error Ratio
BER Bit Error Ratio
C/I Carrier to Interference ratio
CMI Coded Mark Inversion
CSmin minimum practical Channel Separation (for a given radio-frequency channel arrangement)
CW Continuous Wave
dc direct current
DRRS Digital Radio Relay Systems
EIRP Equivalent Isotropically Radiated Power
ETSI

---------------------- Page: 11 ----------------------

SIST EN 300 198 V1.5.1:2005
 10 ETSI EN 300 198 V1.5.1 (2002-07)
EMC ElectroMagnetic Compatibility
ESR Errored Second Ratio
FSK Frequency-Shift Keying (modulation)
IF Intermediate Frequency
IPI Inter-Port Isolation
LO Local Oscillator
PDH Plesiochronous Digital Hierarchy
PRBS Pseudo Random Binary Sequence
QAM Quadrature Amplitude Modulation
RBER Residual BER
RF Radio Frequency
RFC Remote Frequency Control
RSL Receive Signal Level
RTPC Remote Transmit Power Control
SDH Synchronous Digital Hierarchy
SOH Section OverHead
STM-0 medium capacity SDH radio transport module (51,840 Mbit/s AU-3 equivalent, also referred as
STM-0 by ITU-T Recommendation G.861)
STM-N Synchronous Transport Module, level N
sub-STM-0 low capacity SDH radio transport module (n times VC-12 or VC2 equivalent)
TMN Telecommunications Management Network
XPD cross-Polar Discrimination
4 General characteristics
4.1 Frequency bands and channel arrangements
4.1.1 Channel arrangements
The frequency range shall be 22 GHz to 22,6 GHz paired with 23 GHz to 23,6 GHz. The channel arrangements shall be
in accordance with CEPT Recommendation T/R 13-02 [1].
For reader convenience, the basic parameters of the CEPT Recommendation T/R 13-02 [1] are shown in annex A.
4.1.2 Channel spacing for systems operating on the same route
System bit rates and their relevant channel spacing in the present document are reported in table 1 (for the precise
payload bit rates, see clause 5.1).
NOTE: According to systems characteristics the equipment can be connected either to separate antennas or on a
separate polarization to the same antenna.
Table 1: Digital systems channel spacings for various bit rates
Payload Bit 2 2 × 2 8 2 × 8 34 51 140 and 155
Rate [Mbit/s] ⇒
Channel Class 2 equipments 3,5 3,5 7 14 28 56
Spacings [MHz]
Class 4 equipments  3,5 7 14 14/28 56

Class 5 equipments    28
NOTE: n × 2 Mbit/s and n × 34 Mbit/s bit rates may be used where appropriate.
n × 2 Mbit/s mapped into SDH VC12 transport bit rates (sub-STM-0 defined by ITU-T Recommendation
G.708 [20]) may be used where appropriate (e.g. three or four times VC12 into an 8 Mbit/s channel spacing).
The class 2, 2 Mbit/s in 3,5 MHz and the class 4 in 28 MHz reflects equipment more typical to a class 1
(2 Mbit/s) and class 3 (STM-0) system and as a result the adjacent channel interference parameters are
more stringent.

For regulatory purposes in national procedures for licensing radio equipment according to the present document, the
above system types shall be identified by the "system type codes" reported in annex C.
ETSI

---------------------- Page: 12 -----------
...