ETSI ETS 300 474-1 ed.1 (1996-08)
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 1: Portable radio Termination (PT)
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 1: Portable radio Termination (PT)
DE/RES-03043-1
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Profil generičnega dostopa (GAP) - Seznam zahtev za profil in tehnične specifikacije profila proforma izjave o skladnosti izvedbe (ICS) - 1. del: Prenosna radijska zaključitev (PT)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 1: Portable radio Termination (PT)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 474-1 E13SIST ETS 300 474-1:1999en01-jDQXDU-19993SIST ETS 300 474-1:1999SLOVENSKI
STANDARD
SIST ETS 300 474-1:1999
EUROPEANETS 300 474-1TELECOMMUNICATIONAugust 1996STANDARDSource: ETSI TC-RESReference: DE/RES-03043-1ICS:33.020, 33.060.50Key words:DECT, GAP, ICSRadio Equipment and Systems (RES);Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile requirement list and profile-specificImplementation Conformance Statement (ICS) proforma;Part 1: Portable radio Termination (PT)ETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.frTel.: +33 92 94 42 00 - Fax: +33 93 65 47 16Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1996. All rights reserved.SIST ETS 300 474-1:1999
Page 2ETS 300 474-1: August 1996Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 474-1:1999
Page 3ETS 300 474-1: August 1996ContentsForeword.51Scope.72Normative references.73Definitions abbreviations.83.1Definitions.83.2Abbreviations.84Conformance requirement concerning profile ICS.8Annex A (normative):Requirement lists for DECT PT.9A.1General.9A.1.1Profile Requirement List (profile RL).9A.1.2General conditions.10A.2Network (NWK) layer - PT: profile Requirement List (profile RL).10A.2.1Major capabilities.10A.2.1.1Entities.10A.2.1.2CC features.10A.2.1.3MM features.12A.2.1.4SS features (services).13A.2.1.5LCE features.14A.2.1.6Procedures.14A.2.2Messages.16A.2.2.1Call control messages.16A.2.2.2MM messages.22A.2.2.3CRSS and CISS messages.27A.2.2.4Link Control Entity (LCE) messages.27A.2.3Information elements.28A.2.3.1Fixed length information element support.28A.2.3.2Variable length information element supported.29A.2.3.3Escape information elements support.34A.2.4Protocol error handling.34A.3Data Link Control (DLC) layer - PT: profile ICS.34A.3.1Capabilities.34A.3.3.1Services.34A.3.3.1.1C-plane services.34A.3.3.1.2U-plane services.35A.3.3.1.2Management services.35A.3.3.2Procedures.35A.3.3.2.1Generic signalling procedures.35A.3.3.2.2Class A procedures.36A.3.3.2.3Broadcast procedures.36A.3.3.2.4LU1 procedures.36A.3.3.2.5Management procedures.37A.3.3.3Parameters.37A.3.3.3.1LU1 parameters.37A.3.3.4Messages.37A.3.3.4.1C-plane PDUs.37A.4Medium Access Control (MAC) layer - PT: profile ICS.38A.4.1Major Capabilities.38SIST ETS 300 474-1:1999
Page 4ETS 300 474-1: August 1996A.4.1.1Services.38A.4.3.1.1Connection oriented control services.38A.4.1.1.2Broadcast control services.39A.4.1.1.3Multiplexing services.39A.4.1.1.4Management services.40A.4.1.2Procedures.40A.4.1.2.1Connection setup procedures.40A.4.1.2.2Connection data transfer procedures.41A.4.1.2.3Connection handover procedures.41A.4.1.2.4Connection release procedures.41A.4.1.2.5Broadcast procedures.41A.4.1.2.6CSF multiplexing procedures.41A.4.1.2.7Layer management procedures.42A.4.1.3Other capabilities.42A.4.2Messages.42A.4.2.1A - Field.43A.4.2.1.1A - field header - B-field identification.43A.4.2.2A - Field Messages.43A.4.2.2.1Paging tail messages supported.43A.4.2.2.2PT messages information type.44A.4.2.2.3MAC control messages supported.44A.4.2.2.4Broadcast and connectionless (BCL) messages.45A.5Physical (PHL) layer - PT: profile ICS.45A.5.1Physical layer procedures.45Annex B (normative):GAP profile-specific ICS proforma for PT.46B.1Introduction for completing the profile-specific ICS proforma.46B.1.1Purposes and structure.46B.1.3Instructions for completing the profile-specific ICS proforma.48B.2Identification of the implementation.48B.2.1Date of statement.48B.2.2Implementation Under Test (IUT) identification.48B.2.3System Under Test (SUT) identification.48B.2.4Product supplier.49B.2.5Client identification.49B.2.6Contact person identification.49B.3Identification of the protocol.50B.3.1Defect report numbers and amendments implemented.50B.3.2Addenda implemented.50B.4Global statement of conformance.50B.5Capabilities.51B.5.1NWK profile-specific ICS proforma for PT.51B.5.1.1General requirements.51B.5.1.2Application features.51B.5.1.3Application Procedures.51B.5.1.4Management procedures.51B.5.2DLC profile-specific ICS proforma for PT.52B.5.3MAC profile-specific ICS proforma for PT.52B.5.3.1Services.52B.5.3.1.2Extended frequency allocation service.52B.5.4PH profile-specific ICS proforma for PT.52B.5.4.1Requirements.52History.53SIST ETS 300 474-1:1999
Page 5ETS 300 474-1: August 1996ForewordThis European Telecommunication Standard (ETS) has been produced by the Radio Equipment andSystems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).The DECT Generic Access Profile (GAP) profile requirement list and profile-specific ImplementationConformance Statement (ICS) proforma standard comprises two parts as follows:Part 1:"Portable radio Termination (PT)".Part 2:"Fixed radio Termination (FT)".Annex A contains the requirement lists for the Portable radio Termination (PT) Generic Access Profile.Annex B contains the profile-specific ICS proforma for the PT Generic Access Profile.Transposition datesDate of adoption of this ETS:16 August 1996Date of latest announcement of this ETS (doa):30 November 1996Date of latest publication of new National Standardor endorsement of this ETS (dop/e):31 May 1997Date of withdrawal of any conflicting National Standard (dow):31 May 1997SIST ETS 300 474-1:1999
Page 6ETS 300 474-1: August 1996Blank pageSIST ETS 300 474-1:1999
Page 7ETS 300 474-1: August 19961ScopeThis European Telecommunication Standard (ETS) provides the profile Requirment List and profile-specific Implementation Conformance Statement (profile ICS) proforma for the Digital Enhanced CordlessTelecommunications (DECT) Generic Access Profile (GAP) at the Portable radio Termination (PT) asdefined in ETS 300 444 [1] in compliance with the relevant requirements and in accordance with therelevant guidance given in ISO/IEC 9646-7 [7].The supplier of an implementation which is claimed to conform to ETS 300 444 [1] is required to completea copy of the Protocol Implementation Conformance Statement (PICS) proforma ETS 300 476 parts 1, 2,3 and 7 [2], [3], [4] and [5] with the replacements from annex A of this ETS, as well as, a copy of the andprofile-specific ICS proforma provided in annex B of this ETS.2Normative referencesThis ETS incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this ETS only when incorporated in it by amendment or revision. For undated references the latestedition of the publication referred to applies.[1]ETS 300 444: "Radio Equipment and Systems (RES); Digital EuropeanCordless Telecommunications (DECT); Generic Access Profile (GAP)".[2]ETS 300 476-1: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI); ProtocolImplementation Conformance Statement (PICS); Part 1: Network (NWK) layer -Portable radio Termination (PT)".[3]ETS 300 476-2: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI); ProtocolImplementation Conformance Statement (PICS); Part 2: Data Link Control(DCL) layer - Portable radio Termination (PT)".[4]ETS 300 476-3: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI); ProtocolImplementation Conformance Statement (PICS); Part 3: Medium AccessControl (MAC) layer - Portable radio Termination (PT)".[5]ETS 300 476-7: "Radio Equipment and Systems (RES); Digital EnhancedCordless Telecommunications (DECT); Common Interface (CI); ProtocolImplementation Conformance Statement (PICS); Part 7: Physical (PHL) layer".[6]ISO/IEC 9646-1 (1995): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework -Part 1:General concepts". (See also X.290 (1991)).[7]ISO/IEC 9646-7 (1995): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 7:Implementation Conformance Statements".SIST ETS 300 474-1:1999
Page 8ETS 300 474-1: August 19963Definitions abbreviations3.1DefinitionsFor the purposes of this ETS, the following terms and definitions apply:a)the terms defined in ISO/IEC 9646-7 [7];b)the definitions in ETS 300 444 [1]; andc)the following terms defined in ISO/IEC 9646-1 [6]:-PICS proforma;-profile Implementation Conformance Statement (profile ICS).3.2AbbreviationsFor the purposes of this ETS, the abbreviations defined in ISO/IEC 9646-1 [6] and ETS 300 444 [1] apply.4Conformance requirement concerning profile ICSThe supplier of a protocol implementation which is claimed to conform to the portable termination specificrequirements of ETS 300 444 [1] shall verify that his protocol implementation meets the profileRequirements Lists (RLs) for each DECT protocol layer, contained in annex A of this standard, and shallcomplete a copy of the profile-specific ICS proforma provided in annex B and shall provide the informationnecessary to identify both the supplier and the implementation.SIST ETS 300 474-1:1999
Page 9ETS 300 474-1: August 1996Annex A (normative):Requirement lists for DECT PTA.1GeneralThe supplier of a protocol implementation which is claimed to conform to the portable termination specificrequirements of ETS 300 444 [1] shall verify that his particular Network (NWK), Data Link Control (DLC),Medium Access Control (MAC) and PHL layer protocol implementation meets the profile RL for this layer.For this, he shall complete a copy of the corresponding layer PICS proforma contained in annex A ofETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5] updated with the requirements from this annex.A.1.1Profile Requirement List (profile RL)The profile Requirement List (profile RL) for the NWK, DLC, MAC and PHL layers as defined in this annexis based on ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5]. For every capability listed in ETS 300 476Parts 1, 2, 3 and 7 [2], [3], [4] and [5], the profile requirements are expressed by restriction upon allowedsupport answers in ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5]. The profile RL is produced bycopying selected tables from ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5], removing the column(s)to be completed by the supplier, and adding a new set of columns giving the new profile requirements,both in terms of the status and allowed values. The tables are referenced by preceding it withETS 300 476 Parts “[2]”, "[3]", or [4]" as relevant.Profile status columnThe standardised symbols for the status column are as follows:m or Mmandatory - the capability is required to be supported;o or Ooptional - the capability may be supported or not;n/a or N/Anot applicable - in the given context, it is impossible to use the capability;x or Xprohibited (excluded) - there is a requirement not to use this capability in thegiven context;o.i or O.iqualified optional - for mutually exclusive or selectable options from a set. "i" isan integer which identifies an unique group of related optional items and thelogic of their selection which is defined immediately following the table;ci or Ciconditional - the requirement on the capability ("m", "o", "x" or "n/a") depends onthe support of other optional or conditional items. "i" is an integer identifying anunique conditional status expression which is defined immediately following thetable or which is defined in the general condition table below;i or Iout-of-scope - this capability is outside the scope of the given specification, andhence irrelevant and not subject to conformance testing. This status is inparticular applicable for data fields which are reserved for future use. Thestructure of such fields has to be supported, but the value is undefined and thusto be ignored.Reference columnThe reference column gives reference to ETS 300 444 [1], except where explicitly stated otherwise.SIST ETS 300 474-1:1999
Page 10ETS 300 474-1: August 1996A.1.2General conditionsTable A.1:General condition tableCondition identifierCondition definitionc01IF A.7/41 THEN m ELSE iNOTE A:The status of the relevant item is exactly as the status of this item inETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5]. The item has beenincluded as the profile reference column include reference to the profile thatdescribes the item more in details.A.2Network (NWK) layer - PT: profile Requirement List (profile RL)A.2.1Major capabilitiesA.2.1.1EntitiesTo express the profile requirements of ETS 300 444 [1], the following table A.2 indicates the change ofstatus for support of entities.Table A.2: ETS 300 476-1 [2] Table A.12 Entity supportedItemEntity nameProfile referenceProfile status1Call Control (CC)6.2m2Call Independent Supplementary Services (CISS)-i3Connection Oriented Message Services (COMS)-i4ConnectionLess Message Services (CLMS)-i5Mobility Management (MM)6.2m6Link Control Entity (LCE)6.2m7Management (LLME)13mA.2.1.2CC featuresTo express the profile requirements of ETS 300 444 [1], the following table A.3 indicates the change ofstatus for support of features.SIST ETS 300 474-1:1999
Page 11ETS 300 474-1: August 1996Table A.3: ETS 300 476-1 [2] Table A.13 CC features supportedItemFeature nameProfile referenceProfile status1Bell off (Alerting)6.2m2Bell on (Alerting)6.2m3Control of supervisory tones-i4Dial tone detection indication-i5Dialled digits (basic)6.2m6Dialled digits additional-i7Dialling delimiter-i8Dialling delimiter request-i9Display control characters6.2o10Emergency service access request-i11External Handover (inter-cell)-i12Fixed part/portable part capability exchange-i13Go to DTMF (infinite tone length)6.2o14Go to DTMF signalling (defined tone length)6.2m15Go to Pulse6.2o16Group address-i17Incoming call6.2m18Internal call6.2o19Off hook6.2m20On hook (full release)6.2m21Outgoing call6.2m22Packet mode-i23Partial release6.2o24Pause (dialling pause)6.2m25Register recall6.2m26Signalling of display characters6.2o27Selection of bearer service-i28Service call6.2o29Service change-iSIST ETS 300 474-1:1999
Page 12ETS 300 474-1: August 1996A.2.1.3MM featuresTo express the profile requirements of ETS 300 444 [1], the following table A.4 indicates the change ofstatus for support of MM features.Table A.4: ETS 300 476-1 [2] Table A.14 MM features supportedItemFeature nameProf. ref.Prof. status1Authentication of FT6.2o2Authentication of PT6.2m3Authentication of user6.2m4Encryption activation FT initiated6.2m5Encryption activation PT initiated6.2o6Encryption deactivation FT initiated6.2o7Encryption deactivation PT initiated6.2o8Identification of PP6.2m9Inter-operator roaming registration-i10Location de-registration-i11Location registration6.2m12Multiple subscription registration6.6m13On air key allocation6.2m14Service class indication/assignment6.2m15Silent polling-i16Subscription registration procedure on-air6.2m17Subscription registration user procedure with DECT authenticationmodule-i18Subscription registration user procedures keypad (digit entry only)-i19Terminate access rights FT initiated6.2m20Terminate access rights PT initiated-i21ZAP6.2m22MM Partial release (Link control)6.2m23Temporary identity assign-iSIST ETS 300 474-1:1999
Page 13ETS 300 474-1: August 1996A.2.1.4SS features (services)To express the profile requirements of ETS 300 444 [1], the following table A.5 indicates the change ofstatus for support of supplementary services.Table A.5: ETS 300 476-1 [2] Table A.15 SS features (services) supportedItemFeature nameProf. ref.Prof. status1Advice of charge (AOC)-i2Advice of tariff request-i3Call Deflection (CD)-i4Call Forwarding Busy (CFB)-i5Call Forwarding No Reply (CFNR)-i6Call Forwarding Unconditional (CFU)-i7Call Waiting (CW)-i8Calling Line Identification Presentation (CLIP)6.2o9Calling Line Identification Restriction (CLIR)-i10Closed User Group (CUG)-i11Completion of Calls to Busy Subscriber (CCBS)-i12Call HOLD (HOLD)-i13CONFerence call add-on (CONF)-i14COnnected Line identification Presentation (COLP)-i15COnnected Line identification Restriction (COLR)-i16Control of echo control functions-i17Cost information-i18Credit agency public access service-i19Credit public access service-i20Debit public access service-i21Direct Dialling In (DDI)-i22Explicit Call Transfer (ECT)-i23Forced re-connection of held call-i24FreePHone (FPH)-i25Hold call (FT to PT)-i26Hold call (PT to FT)-i27Indication of teleservice available request-i28Indication of teleservices available-i29Malicious Call Identification (MCID)-i30Multiple Subscriber Number (MSN)-i31On-demand (hot bill) public access service- CRSS-i32Queue management-i33Re-connection of held call (FT to PT)-i34Re-connection of held call (PT to FT)-i35Request for indication of temporary subscriber number- CRSS-i36Selection of required teleservice-i37Single step Call Transfer (SCT)-i38Specific trunk carrier selection-i39SUBaddressing (SUB)-i40Terminal Portability (TP)-i41Tree ParTY (3TPY)-i42User to User Signalling UUS-i43CISS Partial release-i44Feature key-i45Indication of subscriber number-i46Register recall-i47Specific line selection-i48External handover switch-iSIST ETS 300 474-1:1999
Page 14ETS 300 474-1: August 1996A.2.1.5LCE featuresTo express the profile requirements of ETS 300 444 [1], table A.6 indicates the change of status forsupport of LCE features.Table A.6: ETS 300 476-1 [2] Table A.16 LCE features supportedItemFeature nameProfile referenceProfile status1Connection oriented Link control (Link control)6.2m2Connectionless oriented Link control-iA.2.1.6ProceduresTo express the profile requirements of ETS 300 444 [1], table A.7 to A.11 indicates the change of statusfor support of the procedures.Table A.7: ETS 300 476-1 [2] Table A.18 CC procedures supportedItemProcedure nameProfile referenceProfile status1cc_outgoing_normal_call_request8.2m4cc_outgoing_selection_of_lower_layer_resources-i5cc_outgoing_connection_of_U_plane8.3, 8.4, 8.5, 8.6m6cc_outgoing_overlap_sending8.3m7cc_outgoing_call_proceeding8.4m8cc_outgoing_call_confirmation8.5m9cc_outgoing_call_connection8.6m10cc_incoming_call_request8.12m11cc_incoming_selection_of_lower_layer_resources-i12cc_incoming_connection_of_U_plane8.15m13cc_incoming_overlap_receiving-i14cc_incoming_call_proceeding-i15cc_incoming_call_confirmation8.13m16cc_incoming_call_connection8.15m17cc_sending_terminal_capability-i18cc_sending_keypad_info8.10m19cc_call_information8.10m20cc_normal_call_release8.7m21cc_partial_release8.9note A22cc_abnormal_call_release8.8m23cc_release_collisions8.7.2.1m31cc_timer_p_cc_02_mgt8.7m32cc_timer_p_cc_03_mgt8.2m33cc_timer_p_cc_04_mgt-i34cc_timer_p_cc_05_mgt8.15m35cc_internal_call_setup8.18note A36cc_service_call_setup8.20note A38cc_service_call_keypad8.21note A39cc_internal_call_keypad8.19note A40pt_alerting8.14m41display8.16note ASIST ETS 300 474-1:1999
Page 15ETS 300 474-1: August 1996Table A.8: ETS 300 476-1 [2] Table A.19 MM procedures supportedItemProcedure nameProfile referenceProfile status1mm_identification_of_pt8.22m2mm_temporary_identity_assignment-i3mm_authentication_of_pt8.24m4mm_authentication_of_user8.25m5mm_authentication_of_ft8.23note A6mm_location_registration8.28m8mm_location_update8.29m9mm_obtain_access_rights8.30m10mm_pt_init_terminate_access_rights-i11mm_ft_init_terminate_access_rights8.31m12mm_key_allocation8.32m13mm_pt_init_parameter_retrieval-i14mm_ft_init_parameter_retrieval-i15mm_pt_init_cipher_switching8.34note A16mm_ft_init_cipher_switching8.33m17mm_zap_increment8.26m18mm_dck_storing8.27m19mm_dck_sending-i20mm_service_class_mgt8.30, 8.24m21mm_partial_release8.39m23mm_timer_p_mm_access_1_mgt8.30.1.1m24mm_timer_p_mm_access_2_mgt-i25mm_timer_p_mm_auth_1_mgt8.32.1.2m26mm_timer_p_mm_cipher_2_mgt8.34.1.1note A27mm_timer_p_mm_locate_1_mgt8.28.1.1m28mm_timer_p_mm_wait_mgt-iTable A.9: ETS 300 476-1 [2] Table A.20
SS protocols supportedItemSS protocol nameProfile referenceProfile status1crss_keypad_protocol8.10m2crss_feature_key_mgt_protocol-i3crss_functional_protocol_smc-i4ciss_keypad_protocol-i5ciss_feature_key_mgt_protocol-i6ciss_partial_release-i7crss_functional_protocol_ciec-i8ciss_functional_protocol_ciec-iTable A.10: ETS 300 476-1 [2] Table A.23 LCE procedures supportedItemProcedure nameProfile referenceProfile status1lce_direct_pt_init_link_establishment8.36m2lce_indirect_ft_init_link_establishment8.35m3lce_direct_ft_init_link_establishment-i5lce_link_suspend-i6lce_link_resume-i7lce_link_release8.37, 8.38m8lce_link_partial_release8.39m9lce_cl_message_routing-i10lce_cl_broadcast_announce-i11lce_timer_lce_01_mgt8.37.1.1m12lce_timer_lce_02_mgt8.39.1.1m13lce_timer_lce_04_mgt-iSIST ETS 300 474-1:1999
Page 16ETS 300 474-1: August 1996Table A.11: ETS 300 476-1 [2] Table A.24 LLME procedures supportedItemProcedure nameProfile referenceProfile status1mgt_prioritised_list_negotiation-i2mgt_exchanged_attribute
...
SLOVENSKI STANDARD
SIST ETS 300 474-1:1999
01-maj-1999
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH '(&7 3URILOJHQHULþQHJD
GRVWRSD *$3 6H]QDP]DKWHY]DSURILOLQWHKQLþQHVSHFLILNDFLMHSURILODSURIRUPD
L]MDYHRVNODGQRVWLL]YHGEH ,&6 GHO 3UHQRVQDUDGLMVND]DNOMXþLWHY 37
Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP);
Profile requirement list and profile specific Implementation Conformance Statement (ICS)
proforma; Part 1: Portable radio Termination (PT)
Ta slovenski standard je istoveten z: ETS 300 474-1 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
SIST ETS 300 474-1:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ETS 300 474-1:1999
---------------------- Page: 2 ----------------------
SIST ETS 300 474-1:1999
EUROPEAN ETS 300 474-1
TELECOMMUNICATION August 1996
STANDARD
Source: ETSI TC-RES Reference: DE/RES-03043-1
ICS: 33.020, 33.060.50
Key words: DECT, GAP, ICS
Radio Equipment and Systems (RES);
Digital Enhanced Cordless Telecommunications (DECT);
Generic Access Profile (GAP);
Profile requirement list and profile-specific
Implementation Conformance Statement (ICS) proforma;
Part 1: Portable radio Termination (PT)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.fr
Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1996. All rights reserved.
---------------------- Page: 3 ----------------------
SIST ETS 300 474-1:1999
Page 2
ETS 300 474-1: August 1996
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.
---------------------- Page: 4 ----------------------
SIST ETS 300 474-1:1999
Page 3
ETS 300 474-1: August 1996
Contents
Foreword .5
1 Scope .7
2 Normative references.7
3 Definitions abbreviations .8
3.1 Definitions .8
3.2 Abbreviations .8
4 Conformance requirement concerning profile ICS.8
Annex A (normative): Requirement lists for DECT PT.9
A.1 General.9
A.1.1 Profile Requirement List (profile RL).9
A.1.2 General conditions.10
A.2 Network (NWK) layer - PT: profile Requirement List (profile RL).10
A.2.1 Major capabilities .10
A.2.1.1 Entities.10
A.2.1.2 CC features .10
A.2.1.3 MM features .12
A.2.1.4 SS features (services).13
A.2.1.5 LCE features .14
A.2.1.6 Procedures.14
A.2.2 Messages.16
A.2.2.1 Call control messages.16
A.2.2.2 MM messages.22
A.2.2.3 CRSS and CISS messages.27
A.2.2.4 Link Control Entity (LCE) messages .27
A.2.3 Information elements .28
A.2.3.1 Fixed length information element support .28
A.2.3.2 Variable length information element supported.29
A.2.3.3 Escape information elements support.34
A.2.4 Protocol error handling.34
A.3 Data Link Control (DLC) layer - PT: profile ICS.34
A.3.1 Capabilities .34
A.3.3.1 Services.34
A.3.3.1.1 C-plane services.34
A.3.3.1.2 U-plane services.35
A.3.3.1.2 Management services .35
A.3.3.2 Procedures.35
A.3.3.2.1 Generic signalling procedures .35
A.3.3.2.2 Class A procedures .36
A.3.3.2.3 Broadcast procedures .36
A.3.3.2.4 LU1 procedures .36
A.3.3.2.5 Management procedures.37
A.3.3.3 Parameters.37
A.3.3.3.1 LU1 parameters.37
A.3.3.4 Messages.37
A.3.3.4.1 C-plane PDUs.37
A.4 Medium Access Control (MAC) layer - PT: profile ICS .38
A.4.1 Major Capabilities .38
---------------------- Page: 5 ----------------------
SIST ETS 300 474-1:1999
Page 4
ETS 300 474-1: August 1996
A.4.1.1 Services . 38
A.4.3.1.1 Connection oriented control services. 38
A.4.1.1.2 Broadcast control services. 39
A.4.1.1.3 Multiplexing services. 39
A.4.1.1.4 Management services. 40
A.4.1.2 Procedures . 40
A.4.1.2.1 Connection setup procedures . 40
A.4.1.2.2 Connection data transfer procedures. 41
A.4.1.2.3 Connection handover procedures. 41
A.4.1.2.4 Connection release procedures . 41
A.4.1.2.5 Broadcast procedures. 41
A.4.1.2.6 CSF multiplexing procedures. 41
A.4.1.2.7 Layer management procedures. 42
A.4.1.3 Other capabilities . 42
A.4.2 Messages. 42
A.4.2.1 A - Field . 43
A.4.2.1.1 A - field header - B-field identification . 43
A.4.2.2 A - Field Messages. 43
A.4.2.2.1 Paging tail messages supported. 43
A.4.2.2.2 P messages information type . 44
T
A.4.2.2.3 MAC control messages supported. 44
A.4.2.2.4 Broadcast and connectionless (BCL) messages . 45
A.5 Physical (PHL) layer - PT: profile ICS. 45
A.5.1 Physical layer procedures . 45
Annex B (normative): GAP profile-specific ICS proforma for PT. 46
B.1 Introduction for completing the profile-specific ICS proforma. 46
B.1.1 Purposes and structure . 46
B.1.3 Instructions for completing the profile-specific ICS proforma . 48
B.2 Identification of the implementation . 48
B.2.1 Date of statement. 48
B.2.2 Implementation Under Test (IUT) identification . 48
B.2.3 System Under Test (SUT) identification. 48
B.2.4 Product supplier . 49
B.2.5 Client identification . 49
B.2.6 Contact person identification. 49
B.3 Identification of the protocol. 50
B.3.1 Defect report numbers and amendments implemented. 50
B.3.2 Addenda implemented . 50
B.4 Global statement of conformance . 50
B.5 Capabilities . 51
B.5.1 NWK profile-specific ICS proforma for PT . 51
B.5.1.1 General requirements. 51
B.5.1.2 Application features . 51
B.5.1.3 Application Procedures. 51
B.5.1.4 Management procedures. 51
B.5.2 DLC profile-specific ICS proforma for PT. 52
B.5.3 MAC profile-specific ICS proforma for PT. 52
B.5.3.1 Services . 52
B.5.3.1.2 Extended frequency allocation service. 52
B.5.4 PH profile-specific ICS proforma for PT. 52
B.5.4.1 Requirements . 52
History. 53
---------------------- Page: 6 ----------------------
SIST ETS 300 474-1:1999
Page 5
ETS 300 474-1: August 1996
Foreword
This European Telecommunication Standard (ETS) has been produced by the Radio Equipment and
Systems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).
The DECT Generic Access Profile (GAP) profile requirement list and profile-specific Implementation
Conformance Statement (ICS) proforma standard comprises two parts as follows:
Part 1: "Portable radio Termination (PT)".
Part 2: "Fixed radio Termination (FT)".
Annex A contains the requirement lists for the Portable radio Termination (PT) Generic Access Profile.
Annex B contains the profile-specific ICS proforma for the PT Generic Access Profile.
Transposition dates
Date of adoption of this ETS: 16 August 1996
Date of latest announcement of this ETS (doa): 30 November 1996
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 May 1997
Date of withdrawal of any conflicting National Standard (dow): 31 May 1997
---------------------- Page: 7 ----------------------
SIST ETS 300 474-1:1999
Page 6
ETS 300 474-1: August 1996
Blank page
---------------------- Page: 8 ----------------------
SIST ETS 300 474-1:1999
Page 7
ETS 300 474-1: August 1996
1 Scope
This European Telecommunication Standard (ETS) provides the profile Requirment List and profile-
specific Implementation Conformance Statement (profile ICS) proforma for the Digital Enhanced Cordless
Telecommunications (DECT) Generic Access Profile (GAP) at the Portable radio Termination (PT) as
defined in ETS 300 444 [1] in compliance with the relevant requirements and in accordance with the
relevant guidance given in ISO/IEC 9646-7 [7].
The supplier of an implementation which is claimed to conform to ETS 300 444 [1] is required to complete
a copy of the Protocol Implementation Conformance Statement (PICS) proforma ETS 300 476 parts 1, 2,
3 and 7 [2], [3], [4] and [5] with the replacements from annex A of this ETS, as well as, a copy of the and
profile-specific ICS proforma provided in annex B of this ETS.
2 Normative references
This ETS incorporates, by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies.
[1] ETS 300 444: "Radio Equipment and Systems (RES); Digital European
Cordless Telecommunications (DECT); Generic Access Profile (GAP)".
[2] ETS 300 476-1: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI); Protocol
Implementation Conformance Statement (PICS); Part 1: Network (NWK) layer -
Portable radio Termination (PT)".
[3] ETS 300 476-2: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI); Protocol
Implementation Conformance Statement (PICS); Part 2: Data Link Control
(DCL) layer - Portable radio Termination (PT)".
[4] ETS 300 476-3: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI); Protocol
Implementation Conformance Statement (PICS); Part 3: Medium Access
Control (MAC) layer - Portable radio Termination (PT)".
[5] ETS 300 476-7: "Radio Equipment and Systems (RES); Digital Enhanced
Cordless Telecommunications (DECT); Common Interface (CI); Protocol
Implementation Conformance Statement (PICS); Part 7: Physical (PHL) layer".
[6] ISO/IEC 9646-1 (1995): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework -Part 1:
General concepts". (See also X.290 (1991)).
[7] ISO/IEC 9646-7 (1995): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 7:
Implementation Conformance Statements".
---------------------- Page: 9 ----------------------
SIST ETS 300 474-1:1999
Page 8
ETS 300 474-1: August 1996
3 Definitions abbreviations
3.1 Definitions
For the purposes of this ETS, the following terms and definitions apply:
a) the terms defined in ISO/IEC 9646-7 [7];
b) the definitions in ETS 300 444 [1]; and
c) the following terms defined in ISO/IEC 9646-1 [6]:
- PICS proforma;
- profile Implementation Conformance Statement (profile ICS).
3.2 Abbreviations
For the purposes of this ETS, the abbreviations defined in ISO/IEC 9646-1 [6] and ETS 300 444 [1] apply.
4 Conformance requirement concerning profile ICS
The supplier of a protocol implementation which is claimed to conform to the portable termination specific
requirements of ETS 300 444 [1] shall verify that his protocol implementation meets the profile
Requirements Lists (RLs) for each DECT protocol layer, contained in annex A of this standard, and shall
complete a copy of the profile-specific ICS proforma provided in annex B and shall provide the information
necessary to identify both the supplier and the implementation.
---------------------- Page: 10 ----------------------
SIST ETS 300 474-1:1999
Page 9
ETS 300 474-1: August 1996
Annex A (normative): Requirement lists for DECT PT
A.1 General
The supplier of a protocol implementation which is claimed to conform to the portable termination specific
requirements of ETS 300 444 [1] shall verify that his particular Network (NWK), Data Link Control (DLC),
Medium Access Control (MAC) and PHL layer protocol implementation meets the profile RL for this layer.
For this, he shall complete a copy of the corresponding layer PICS proforma contained in annex A of
ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5] updated with the requirements from this annex.
A.1.1 Profile Requirement List (profile RL)
The profile Requirement List (profile RL) for the NWK, DLC, MAC and PHL layers as defined in this annex
is based on ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5]. For every capability listed in ETS 300 476
Parts 1, 2, 3 and 7 [2], [3], [4] and [5], the profile requirements are expressed by restriction upon allowed
support answers in ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5]. The profile RL is produced by
copying selected tables from ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5], removing the column(s)
to be completed by the supplier, and adding a new set of columns giving the new profile requirements,
both in terms of the status and allowed values. The tables are referenced by preceding it with
ETS 300 476 Parts “[2]”, "[3]", or [4]" as relevant.
Profile status column
The standardised symbols for the status column are as follows:
m or M mandatory - the capability is required to be supported;
o or O optional - the capability may be supported or not;
n/a or N/A not applicable - in the given context, it is impossible to use the capability;
x or X prohibited (excluded) - there is a requirement not to use this capability in the
given context;
o.i or O.i qualified optional - for mutually exclusive or selectable options from a set. "i" is
an integer which identifies an unique group of related optional items and the
logic of their selection which is defined immediately following the table;
ci or Ci conditional - the requirement on the capability ("m", "o", "x" or "n/a") depends on
the support of other optional or conditional items. "i" is an integer identifying an
unique conditional status expression which is defined immediately following the
table or which is defined in the general condition table below;
i or I out-of-scope - this capability is outside the scope of the given specification, and
hence irrelevant and not subject to conformance testing. This status is in
particular applicable for data fields which are reserved for future use. The
structure of such fields has to be supported, but the value is undefined and thus
to be ignored.
Reference column
The reference column gives reference to ETS 300 444 [1], except where explicitly stated otherwise.
---------------------- Page: 11 ----------------------
SIST ETS 300 474-1:1999
Page 10
ETS 300 474-1: August 1996
A.1.2 General conditions
Table A.1:General condition table
Condition identifier Condition definition
c01 IF A.7/41 THEN m ELSE i
NOTE A: The status of the relevant item is exactly as the status of this item in
ETS 300 476 Parts 1, 2, 3 and 7 [2], [3], [4] and [5]. The item has been
included as the profile reference column include reference to the profile that
describes the item more in details.
A.2 Network (NWK) layer - PT: profile Requirement List (profile RL)
A.2.1 Major capabilities
A.2.1.1 Entities
To express the profile requirements of ETS 300 444 [1], the following table A.2 indicates the change of
status for support of entities.
Table A.2: ETS 300 476-1 [2] Table A.12 Entity supported
Item Entity name Profile reference Profile status
1 Call Control (CC) 6.2 m
2 Call Independent Supplementary Services (CISS) - i
3 Connection Oriented Message Services (COMS) - i
4 ConnectionLess Message Services (CLMS) - i
5 Mobility Management (MM) 6.2 m
6 Link Control Entity (LCE) 6.2 m
7 Management (LLME) 13 m
A.2.1.2 CC features
To express the profile requirements of ETS 300 444 [1], the following table A.3 indicates the change of
status for support of features.
---------------------- Page: 12 ----------------------
SIST ETS 300 474-1:1999
Page 11
ETS 300 474-1: August 1996
Table A.3: ETS 300 476-1 [2] Table A.13 CC features supported
Item Feature name Profile reference Profile status
1 Bell off (Alerting) 6.2 m
2 Bell on (Alerting) 6.2 m
3 Control of supervisory tones - i
4 Dial tone detection indication - i
5 Dialled digits (basic) 6.2 m
6 Dialled digits additional - i
7 Dialling delimiter - i
8 Dialling delimiter request - i
9 Display control characters 6.2 o
10 Emergency service access request - i
11 External Handover (inter-cell) - i
12 Fixed part/portable part capability exchange - i
13 Go to DTMF (infinite tone length) 6.2 o
14 Go to DTMF signalling (defined tone length) 6.2 m
15 Go to Pulse 6.2 o
16 Group address - i
17 Incoming call 6.2 m
18 Internal call 6.2 o
19 Off hook 6.2 m
20 On hook (full release) 6.2 m
21 Outgoing call 6.2 m
22 Packet mode - i
23 Partial release 6.2 o
24 Pause (dialling pause) 6.2 m
25 Register recall 6.2 m
26 Signalling of display characters 6.2 o
27 Selection of bearer service - i
28 Service call 6.2 o
29 Service change - i
---------------------- Page: 13 ----------------------
SIST ETS 300 474-1:1999
Page 12
ETS 300 474-1: August 1996
A.2.1.3 MM features
To express the profile requirements of ETS 300 444 [1], the following table A.4 indicates the change of
status for support of MM features.
Table A.4: ETS 300 476-1 [2] Table A.14 MM features supported
Item Feature name Prof. ref. Prof. status
1 Authentication of FT 6.2 o
2 Authentication of PT 6.2 m
3 Authentication of user 6.2 m
4 Encryption activation FT initiated 6.2 m
5 Encryption activation PT initiated 6.2 o
6 Encryption deactivation FT initiated 6.2 o
7 Encryption deactivation PT initiated 6.2 o
8 Identification of PP 6.2 m
9 Inter-operator roaming registration - i
10 Location de-registration - i
11 Location registration 6.2 m
12 Multiple subscription registration 6.6 m
13 On air key allocation 6.2 m
14 Service class indication/assignment 6.2 m
15 Silent polling - i
16 Subscription registration procedure on-air 6.2 m
17 Subscription registration user procedure with DECT authentication-i
module
18 Subscription registration user procedures keypad (digit entry only) - i
19 Terminate access rights FT initiated 6.2 m
20 Terminate access rights PT initiated - i
21 ZAP 6.2 m
22 MM Partial release (Link control) 6.2 m
23 Temporary identity assign - i
---------------------- Page: 14 ----------------------
SIST ETS 300 474-1:1999
Page 13
ETS 300 474-1: August 1996
A.2.1.4 SS features (services)
To express the profile requirements of ETS 300 444 [1], the following table A.5 indicates the change of
status for support of supplementary services.
Table A.5: ETS 300 476-1 [2] Table A.15 SS features (services) supported
Item Feature name Prof. ref. Prof. status
1 Advice of charge (AOC) - i
2 Advice of tariff request - i
3 Call Deflection (CD) - i
4 Call Forwarding Busy (CFB) - i
5 Call Forwarding No Reply (CFNR) - i
6 Call Forwarding Unconditional (CFU) - i
7 Call Waiting (CW) - i
8 Calling Line Identification Presentation (CLIP) 6.2 o
9 Calling Line Identification Restriction (CLIR) - i
10 Closed User Group (CUG) - i
11 Completion of Calls to Busy Subscriber (CCBS) - i
12 Call HOLD (HOLD) - i
13 CONFerence call add-on (CONF) - i
14 COnnected Line identification Presentation (COLP) - i
15 COnnected Line identification Restriction (COLR) - i
16 Control of echo control functions - i
17 Cost information - i
18 Credit agency public access service - i
19 Credit public access service - i
20 Debit public access service - i
21 Direct Dialling In (DDI) - i
22 Explicit Call Transfer (ECT) - i
23 Forced re-connection of held call - i
24 FreePHone (FPH) - i
25 Hold call (FT to PT) - i
26 Hold call (PT to FT) - i
27 Indication of teleservice available request - i
28 Indication of teleservices available - i
29 Malicious Call Identification (MCID) - i
30 Multiple Subscriber Number (MSN) - i
31 On-demand (hot bill) public access service- CRSS - i
32 Queue management - i
33 Re-connection of held call (FT to PT) - i
34 Re-connection of held call (PT to FT) - i
35 Request for indication of temporary subscriber number- CRSS - i
36 Selection of required teleservice - i
37 Single step Call Transfer (SCT) - i
38 Specific trunk carrier selection - i
39 SUBaddressing (SUB) - i
40 Terminal Portability (TP) - i
41 Tree ParTY (3TPY) - i
42 User to User Signalling UUS - i
43 CISS Partial release - i
44 Feature key - i
45 Indication of subscriber number - i
46 Register recall - i
47 Specific line selection - i
48 External handover switch - i
---------------------- Page: 15 ----------------------
SIST ETS 300 474-1:1999
Page 14
ETS 300 474-1: August 1996
A.2.1.5 LCE features
To express the profile requirements of ETS 300 444 [1], table A.6 indicates the change of status for
support of LCE features.
Table A.6: ETS 300 476-1 [2] Table A.16 LCE features supported
Item Feature name Profile reference Profile status
1 Connection oriented Link control (Link control) 6.2 m
2 Connectionless oriented Link control - i
A.2.1.6 Procedures
To express the profile requirements of ETS 300 444 [1], table A.7 to A.11 indicates the change of status
for support of the procedures.
Table A.7: ETS 300 476-1 [2] Table A.18 CC procedures supported
Item Procedure name Profile reference Profile status
1 cc_outgoing_normal_call_request 8.2 m
4 cc_outgoing_selection_of_lower_layer_resources - i
5 cc_outgoing_connection_of_U_plane 8.3, 8.4, 8.5, 8.6 m
6 cc_outgoing_overlap_sending 8.3 m
7 cc_outgoing_call_proceeding 8.4 m
8 cc_outgoing_call_confirmation 8.5 m
9 cc_outgoing_call_connection 8.6 m
10 cc_incoming_call_request 8.12 m
11 cc_incoming_selection_of_lower_layer_resources - i
12 cc_incoming_connection_of_U_plane 8.15 m
13 cc_incoming_overlap_receiving - i
14 cc_incoming_call_proceeding - i
15 cc_incoming_call_confirmation 8.13 m
16 cc_incoming_call_connection 8.15 m
17 cc_sending_terminal_capability - i
18 cc_sending_keypad_info 8.10 m
19 cc_call_information 8.10 m
20 cc_normal_call_release 8.7 m
21 cc_partial_release 8.9 note A
22 cc_abnormal_call_release 8.8 m
23 cc_release_collisions 8.7.2.1 m
31 cc_timer_p_cc_02_mgt 8.7 m
32 cc_time
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.