ETSI TS 103 929 V1.2.1 (2023-05)

Cyber Security (CYBER); Mapping of specific requirements of standardisation request for RED articles 3(3)(d), 3(3)(e) and 3(3)(f) to IEC 62443-4-2 requirements and to ETSI EN 303 645 provisions

RTS/CYBER-00101

General Information

• Status: Not Published
• Technical Committee: CYBER - Cyber Security
• Current Stage: 12 - Citation in the OJ (auto-insert)
• Due Date: 06-Jun-2023
• Completion Date: 30-May-2023

Standards Content (Sample)

ETSI TS 103 929 V1.2.1 (2023-05)






TECHNICAL SPECIFICATION
Cyber Security (CYBER);
Mapping of specific requirements of standardisation request
for RED articles 3(3)(d), 3(3)(e) and 3(3)(f) to
IEC 62443-4-2 requirements and to ETSI EN 303 645 provisions

---------------------- Page: 1 ----------------------
2 ETSI TS 103 929 V1.2.1 (2023-05)

Reference
RTS/CYBER-00101
Keywords
cyber security
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
https://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
rule and/or regulation and further, no representation or warranty is made of merchantability or fitness
and/or governmental
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2023.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 103 929 V1.2.1 (2023-05)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 6
3.3 Abbreviations . 6
4 Methodology . 6
4.1 Mapping of IEC 62443-4-2 requirements . 6
4.2 Mapping of ETSI EN 303 645 provisions . 7
4.3 Mapping notations . 7
5 Mapping results and resulting transition requirements . 8
5.1 Mapping results based on IEC 62443-4-2 requirements . 8
5.2 Mapping results based on ETSI EN 303 645 provisions . 11
5.3 Transition requirements based on mapping results . 13
History . 14


ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 103 929 V1.2.1 (2023-05)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Cyber Security (CYBER).
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
According to the standardisation request [i.5], harmonised standards (hENs) are to be developed for the articles 3(3)(d),
3(3)(e) and 3(3)(f) of the Radio Equipment Directive (RED) [i.1]. Due to the adoption of the delegated act [i.2], the
st
essential requirements given in the RED articles 3(3)(d), (e) and (f) will come into force on the 1 of August 2024.
It is understood that requirements from IEC 62443-4-2 [i.4] and the provisions from ETSI EN 303 645 [i.3] address
many products that fall under the scope of the RED articles 3(3)(d), 3(3)(e) and 3(3)(f). The ETSI EN 303 645 [i.3]
goes even beyond the scope of the RED [i.1] as the ETSI EN 303 645 [i.3] does not only cover product-related
requirements, but also process-related requirements addressing the manufacturer.
The present document shows the mapping of specific requirements of the standardisation request for the RED
articles 3(3)(d), 3(3)(e) and 3(3)(f) to IEC 62443-4-2 [i.4] requirements and to ETSI EN 303 645 [i.3] provisions. This
could be useful, e.g. for industry stakeholders to be prepared for and implement the transition from product conformity
with IEC 62443-4-2 [i.4] and/or ETSI EN 303 645 [i.3] to product conformity with future requirements in the hENs for
the RED articles 3(3)(d), 3(3)(e) and 3(3)(f). In addition, the mapping results could be referenced for work on the hENs
for the RED articles 3(3)(d), 3(3)(e) and 3(3)(f).
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 103 929 V1.2.1 (2023-05)
1 Scope
The present document provides mapping tables to show which security requirements and provisions from the
IEC 62443-4-2 [i.4] and the ETSI EN 303 645 [i.3], respectively, cover the specific requirements from the
standardisation request for the RED articles 3(3)(d), 3(3)(e) and 3(3)(f) and are therefore relevant to fulfil the essential
requirements given by the RED articles 3(3)(d), 3(3)(e) and 3(3)(f). In addition, so-called transition requirements are
provided which help and are to be considered for implementing the transition from product conformity based on
provisions from ETSI EN 303 645 [i.3] and/or requirements from IEC 62443-4-2 [i.4] to product conformity based on
the RED delegated regulation [i.2].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Delegated Regulation (EU) 2022/30 of 29 October 2021 supplementing Directive
2014/53/EU of the European Parliament and of the Council with regard to the application of the
essential requirements referred to in Article 3(3), points (d), (e) and (f), of that Directive.
[i.3] ETSI EN 303 645 (V2.1.1): "CYBER; Cyber Security for Consumer Internet of Things: Baseline
Requirements".
[i.4] IEC 62443-4-2:2019: "Security for industrial automation and control systems - Part 4-2: Technical
security requirements for IACS components".
[i.5] C(2022)5637 - M/585: "Commission Implementing Decision of 5.8.2022 on a standardisation
request to the European Committee for Standardisation and the European Committee for
Electrotechnical Standardisation as regards radio equipment in support of Directive 2014/53/EU of
the European Parliament and of the Council and Commission Delegated Regulation (EU)
2022/30".
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 103 929 V1.2.1 (2023-05)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in [i.1], [i.2], [i.3], [i.4], [i.5] and the following apply:
process-related requirement: requirement that is addressed to the process around the product functionality
EXAMPLE: If a standard requires that a product manufacturer provides a publicly available vulnerability
disclosure p
...