ETSI TS 102 545-2 V1.3.1 (2009-06)

Broadband Radio Access Networks (BRAN); HiperMAN; Conformance Testing for WiMAX/HiperMAN 1.3.1 Part 2: Test Suite Structure and Test Purposes (TSS&TP)

RTS/BRAN-004T008-2-R2

General Information

• Status: Published
• Publication Date: 10-Jun-2009
• Technical Committee: BRAN - Broadband Radio Access Networks
• Current Stage: 12 - Completion
• Due Date: 28-May-2009
• Completion Date: 11-Jun-2009

Standards Content (Sample)

ETSI TS 102 545-2 V1.3.1 (2009-06)
Technical Specification


Broadband Radio Access Networks (BRAN);
HiperMAN;
Conformance Testing for WiMAX/HiperMAN 1.3.1;
Part 2: Test Suite Structure and Test Purposes (TSS&TP)

---------------------- Page: 1 ----------------------
2 ETSI TS 102 545-2 V1.3.1 (2009-06)



Reference
RTS/BRAN-004T008-2-R2
Keywords
ATS, broadband, DLC, FWA, HiperMAN, MAC,
point-to-multipoint, radio, testing, TSS&TP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
© WIMAX Forum 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 102 545-2 V1.3.1 (2009-06)
Contents
Intellectual Property Rights.8
Foreword.8
1 Scope.9
2 References.9
2.1 Normative references.9
2.2 Informative references.10
3 Definitions and abbreviations.10
3.1 Definitions.10
3.2 Abbreviations.10
4 Test Suite Structure (TSS).12
4.1 Structure.12
4.2 Test groups.15
4.2.1 Protocol services.15
4.2.1.1 Packet convergence sublayer Encapsulation.15
4.2.1.2 Packet convergence sublayer Classification.15
4.2.1.3 Payload Header Suppression.15
4.2.1.4 MAC PDU Formats.15
4.2.1.5 ARQ.15
4.2.1.6 Radio Link Control (RLC) .15
4.2.1.7 Registration, IP connectivity and TFTP.16
4.2.1.8 Dynamic services.16
4.2.1.9 Bandwidth allocation and polling .16
4.2.1.10 General Handover functionality.16
4.2.1.11 Sleep mode.16
4.2.1.12 Idle mode .16
4.2.1.13 Multicast Traffic connections.16
4.2.1.14 Supported Cryptographic Suites.16
4.2.1.15 Privacy and key management.16
4.2.1.16 Security version 2.16
4.2.1.17 Channel descriptors and maps.16
4.2.1.18 Multicast and Broadcast Services .16
4.2.1.19 Adaptive Antenna Support.17
4.2.1.20 Reset and re-registration .17
4.2.1.21 Clock comparison.17
4.2.2 Main test types.17
4.2.2.1 Valid Behaviour (BV) tests.17
4.2.2.2 Invalid Behaviour (BI) tests .17
4.2.2.3 Inopportune Behaviour (BO) tests .17
4.2.2.4 Timer and counter (TI) tests.17
5 Test Purposes (TP).18
5.1 Introduction.18
5.1.1 TP definition conventions.18
5.1.2 TP Identifier naming conventions.19
5.1.3 Sources of TP definitions.21
5.1.4 TP selection criteria name convention.22
5.2 Test purposes for BS (BS).23
5.2.1 CS Options: Encapsulation (CSOE) .23
5.2.1.1 IP version 4 (IP4) .23
5.2.1.2 IP version 6 (IP6) .23
5.2.1.3 IP version 4 with ROHC (IP4R) .24
5.2.1.4 IP version 6 with ROHC (IP6R) .24
5.2.1.5 Ethernet (ENET).25
5.2.1.6 IP version 4 over Ethernet.25
ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 102 545-2 V1.3.1 (2009-06)
5.2.1.7 IP version 6 over Ethernet.26
5.2.2 CS Options: Classification.26
5.2.2.1 Classifier DSx Signalling (CDS).27
5.2.2.2 IPv4 classification (IP4C) .29
5.2.2.3 IPv6 classification (IP6C) .30
5.2.2.4 Ethernet classification (ENTC) .32
5.2.2.4.1 Pure Ethernet Classification (PETC).32
5.2.2.4.2 IPv4 over Ethernet (IP4oE) .33
5.2.2.4.3 IPv6 over Ethernet (IP6oE) .36
5.2.2.5 VLAN (VLAN).39
5.2.2.5.1 IP over VLAN (IPoV) .39
5.2.3 Payload Header Suppression (PHS).40
5.2.4 MAC PDU Construction (MAC).47
5.2.4.1 PDU Concatenation (CAT) .51
5.2.4.2 Fragmentation (FRAG).51
5.2.4.3 Packing (PACK).53
5.2.4.4 Cyclic Redundancy Check (CRC).55
5.2.5 Automatic Repeat Request (ARQ).55
5.2.5.1 Receiver Operations (RXD).58
5.2.5.2 Transmit Data (TXD).61
5.2.5.3 Reset (RE).67
5.2.6 Radio Link Control (RLC).69
5.2.6.1 Initial Ranging (IRNG) .69
5.2.6.2 Periodic Ranging (PRNG).75
5.2.6.3 Downlink Burst Profile Management (DBPC).79
5.2.6.3.1 Change to a Less Robust Profile (LRP).79
5.2.6.3.2 Change to a More Robust Profile (MRP) .80
5.2.6.4 Negotiate Basic Capabilities (SBC) .80
5.2.6.5 Feedback Mechanism (FBK) .81
5.2.6.5.1 Feedback Polling.81
5.2.6.5.2 Fast-Feedback.82
5.2.6.6 MAC-support for HARQ (HARQ) .82
5.2.6.6.1 DL HARQ Operation .82
5.2.6.6.2 UL HARQ Operation .85
5.2.7 Registration, IP Connectivity and Parameter Transfer (INI) .85
5.2.7.1 Registration (REG).85
5.2.7.2 IP Connectivity (IPC).87
5.2.8 Dynamic Services (DS).89
5.2.8.1 Dynamic Services Addition (DSA).89
5.2.8.2 Dynamic Services Change (DSC) .103
5.2.8.3 Dynamic Services Deletion (DSD) .118
5.2.8.4 QoS Parameter Sets (QPS).122
5.2.9 Bandwidth Allocation and Polling (BWA).133
5.2.9.1 CDMA Bandwidth Request (CBR).135
5.2.9.2 Request/Grant (REQ).135
5.2.9.3 Multicast Polling (MCP).142
5.2.10 General Handover Functionality (GHF) .145
5.2.10.1 Network topology acquisition (NTA) .145
5.2.10.1.1 Network advertisement (NWA).145
5.2.10.1.2 Scanning (SCAN).145
5.2.10.2 HO process (HO) .146
5.2.10.2.1 Process at Serving BS (SVG) .146
5.2.10.2.2 Process at Target BS (TGT) .149
5.2.11 Sleep Mode (SLM) .153
5.2.11.1 Power Saving Class Type 1 (PW1).153
5.2.11.2 Power Saving Class Type 2 (PW2).157
5.2.11.3 Power Saving Class Type 3 (PW3).157
5.2.11.4 Periodic Ranging during Sleep Mode (PRSM) .157
5.2.12 Idle Mode (IDM).158
5.2.12.1 Transition to Idle Mode (TDIM).158
5.2.12.1.1 Valid Behaviour.158
5.2.12.1.2 Timer.159
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 102 545-2 V1.3.1 (2009-06)
5.2.12.2 Paging (PG).159
5.2.12.3 Power Down Update (PWD).161
5.2.12.4 Network Re-Entry (NWR) .161
5.2.12.5 Location update (LOC).164
5.2.13 Multicast Traffic Connections (MTC) .164
5.2.14 Supported Cryptographic Suites (SCS).165
5.2.14.1 No data encryption, No data authentication and No key encryption.165
5.2.14.2 CCM-mode 128-bit AES, CCM-Mode and AES Key Wrap with 128-bit key (AES) .165
5.2.15 Privacy and Key Management (PKM).167
5.2.15.1 PKM Version 1 Authentication/Authorization (AUTH1).167
5.2.15.1.1 Initialization (INIT).167
5.2.15.1.2 Operational (OPN).172
5.2.15.2 Encryption Key Transfer (TEK) .174
5.2.15.2.1 Initialization (INIT).174
5.2.15.2.2 Operational (OPN).176
5.2.15.3 Security Association Management (SAM).178
5.2.15.4 Encryption and Key Scheduling (EKS).179
5.2.15.4.1 Key Usage (KU).181
5.2.15.4.2 Encryption (ENC).182
5.2.15.4.3 Decryption (DEC).184
5.2.15.5 Certificates (CERT).186
5.2.16 Security version 2 (SEC) .186
5.2.16.1 BS/SEC/PKMv2/AUTH/NWE - Initial Network Entry.186
5.2.16.2 BS/SEC/PKMv2/AUTH/REA - Reauthorization.187
5.2.16.3 BS/SEC/PKMv2/AUTH/HAN - Handover process.187
5.2.16.3a BS/SEC/PKMv2/AUTH/IDM - Idle Mode.190
5.2.16.4 BS/SEC/PKMv2/AUTH/AKI - Initial authorization AK.191
5.2.16.5 BS/SEC/PKMv2/AUTH/AKR - Reauthorization AK.192
5.2.16.6 BS/SEC/PKMv2/TEK - Traffic Encryption Key .193
5.2.16.7 BS/SEC/PKMv2/GSA - Group Security Association .194
5.2.17 Channel Descriptors and Maps (CDM) .195
5.2.17.1 Map and Frame Structure (MFS) .195
5.2.17.2 Channel Descriptors (CD).198
5.2.17.3 Channel Descriptor Change (CDC).200
5.2.17.3.1 Uplink (UL).200
5.2.17.3.2 Downlink (DL).201
5.2.17.4 MAP IEs (MAP) .202
5.2.18 Multicast and Broadcast Services (MBS) .204
5.2.19 Adaptive Antenna Support (AAS) .207
5.2.20 Reset and Re-registration (RER) .208
5.2.21 Clock Comparison (CCC).210
5.3 Test purposes for SS (SS).211
5.3.1 CS Options: Encapsulation (CSOE) .211
5.3.1.1 IP version 4 (IP4) .211
5.3.1.2 IP version 6 (IP6) .211
5.3.1.3 IP version 4 with ROHC/ECRTP (IP4R).212
5.3.1.4 IP version 6 with ROHC/ECRTP (IP6R).212
5.3.1.5 Ethernet (ENET).213
5.3.1.6 IP version 4 over Ethernet (IP4oE) .213
5.3.1.7 IP version 6 over Ethernet (IP6oE) .214
5.3.2 CS Options: Classification (CSOC).214
5.3.2.1 Classifier DSx Signalling (CDS).214
5.3.2.2 IPv4 Classification (IP4C) .216
5.3.2.3 IPv6 Classification (IP6C) .218
5.3.2.4 Ethernet Classification (ENTC).220
5.3.2.4.1 Pure Ethernet Classification (PETC).220
5.3.2.4.2 IPv4 over Ethernet (IP4oE) .221
5.3.2.4.3 IPv6 over Ethernet (IP6oE) .224
5.3.2.5 VLAN (VLAN).226
5.3.2.5.1 IP over VLAN (IPoV) .226
5.3.3 Payload Header Suppression (PHS).227
5.3.4 MAC PDU Construction (MAC).232
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 102 545-2 V1.3.1 (2009-06)
5.3.4.1 PDU Concatenation (CAT) .234
5.3.4.2 Fragmentation (FRAG).235
5.3.4.3 Packing (PACK).
...