ETSI TS 102 177 V1.5.1 (2010-05)

Broadband Radio Access Networks (BRAN); HiperMAN; Physical (PHY) layer

RTS/BRAN-0040001r6

General Information

• Status: Published
• Publication Date: 24-May-2010
• Technical Committee: BRAN - Broadband Radio Access Networks
• Current Stage: 12 - Completion
• Due Date: 28-May-2010
• Completion Date: 25-May-2010

Standards Content (Sample)

ETSI TS 102 177 V1.5.1 (2010-05)
Technical Specification


Broadband Radio Access Networks (BRAN);
HiperMAN;
Physical (PHY) layer

---------------------- Page: 1 ----------------------
2 ETSI TS 102 177 V1.5.1 (2010-05)



Reference
RTS/BRAN-0040001r6
Keywords
access, broadband, FWA, HiperMAN, layer 1,
MAN, nomadic, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 102 177 V1.5.1 (2010-05)
Contents
Intellectual Property Rights . 5
Foreword . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 8
4 HiperMAN OFDM PHY . 9
4.1 OFDM symbol description . 9
4.2 Transmitted signal . 10
4.3 Channel coding . 12
4.3.1 Randomization . 12
4.3.2 Forward Error Correction (FEC) . 13
4.3.2.1 Concatenated Reed-Solomon / Convolutional Code (RS-CC) . 13
4.3.2.2 Convolutional Turbo Coding (Optional) . 15
4.3.2.2.1 CTC interleaver . 16
4.3.2.2.2 Determination of CTC circulation states . 17
4.3.2.2.3 CTC puncturing . 17
4.3.3 Interleaving . 17
4.3.4 Modulation . 18
4.3.4.1 Data modulation . 18
4.3.4.2 Pilot modulation . 19
4.3.4.3 Rate ID encodings . 20
4.3.5 Example UL RS-CC Encoding . 20
4.3.5.1 Full bandwidth (16 subchannels) . 20
4.3.5.2 Subchannelization (2 subchannels) . 21
4.3.5.3 Subchannelization (1 subchannel) . 22
4.3.6 Preamble structure and modulation . 22
4.3.6.1 Transmission Convergence (TC) sublayer . 25
4.4 Frame structures . 25
4.4.1 PMP . 25
4.4.1.1 Duplexing modes . 25
4.4.1.2 DL frame prefix . 28
4.4.1.3 PMP DL subchannelization zone . 28
4.4.1.4 PMP-AAS zone . 31
4.4.2 Mesh . 34
4.4.3 Frame duration codes . 35
4.5 Control mechanisms . 35
4.5.1 Synchronization . 35
4.5.1.1 Network synchronization . 35
4.6 Ranging . 35
4.6.1 Initial Ranging in AAS systems . 38
4.6.2 Bandwidth requesting . 38
4.6.2.1 Parameter selection . 38
4.6.2.2 Full contention transmission . 40
4.6.2.3 Focused contention transmission . 40
4.6.3 Power control . 41
4.6.3.1 Closed loop power control . 41
4.6.3.2 Open loop power control (optional) . 41
4.7 Transmit diversity space-time coding (optional) . 43
4.7.1 STC 2X2 . 44
ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 102 177 V1.5.1 (2010-05)
4.7.1.1 STC 2x2 coding . 44
4.7.1.2 STC 2x2 decoding . 45
4.8 Channel quality measurements . 45
4.8.1 Introduction. 45
4.8.2 RSSI mean and standard deviation . 46
4.8.3 CINR mean and standard deviation . 47
4.9 Transmitter requirements . 47
4.9.1 Transmitter channel bandwidth. 48
4.9.2 Transmit power level control . 48
4.9.2.1 Transmitter spectral flatness. 48
4.9.2.2 Transmitter constellation error and test method . 48
4.10 Receiver requirements . 49
4.10.1 Receiver sensitivity . 49
4.10.2 Receiver adjacent and alternate channel rejection . 50
4.10.3 Receiver maximum input signal . 51
4.10.4 Receiver linearity . 51
4.11 Frequency and timing requirements . 51
4.12 Parameters and constants . 51
5 HiperMAN OFDMA PHY . 52
History . 53

ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 102 177 V1.5.1 (2010-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document describes the physical layer specifications for High PERformance Radio Metropolitan Area
Network (HiperMAN). Separate ETSI documents provide details on the system overview, Data Link Control (DLC)
layer, Convergence Layers (CL) and conformance testing requirements for HiperMAN.
®
With permission of IEEE (on file as BRAN43d016), portions of the present document are excerpted from
IEEE Standards [2] and [3].
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 102 177 V1.5.1 (2010-05)
1 Scope
The present document specifies the HiperMAN air interface with the specification layer 1 (physical layer), which can be
used to provide Fixed applications, in frequencies below 11 GHz, and Nomadic and converged Fixed-Nomadic
applications, in frequencies below 6 GHz. The present document follows the ISO-OSI model. HiperMAN is confined
only to the radio subsystems consisting of the Physical (PHY) layer and the DLC layer - which are both core network
independent - and the core network specific convergence sub-layer.
For managing radio resources and connection control, the Data Link Control (DLC) protocol is applied, which uses the
transmission services of the DLC layer. Convergence layers above the DLC layer handle the inter-working with layers
at the top of the radio sub-system.
The scope of the present document is as follows:
• It gives a description of the physical layer for HiperMAN systems.
• It specifies the transmission scheme in order to allow interoperability between equipment developed by
different manufacturers. This is achieved by describing scrambling, channel coding, modulation, framing,
control mechanisms, and power control to assist in radio resource management.
• It does cover the receiver and transmitter performance requirements which are specific for HiperMAN
systems.
• Some information clauses and annexes describe parameters and system models to assist in preparing
conformance, interoperability and coexistence specifications.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 102 178: "Broadband Radio Access Networks (BRAN); HiperMAN; Data Link Control
(DLC) layer".
[2] IEEE 802.16-2004: "IEEE Standard for Local and Metropolitan Area Networks - Part 16: Air
Interface for Fixed Broadband Wireless Access Systems".
[3] IEEE 802.16e-2005: "IEEE Standard for Local and metropolitan area networks - Part 16: Air
Interface for Fixed and Mobile Broadband Wireless Access Systems - Amendment 2: Physical and
Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands and
Corrigendum 1".
[4] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
TM
[5] IEEE Std 802.16 -2009: "IEEE Standard for Local and metropolitan area networks Part 16: Air
Interface for Broadband Wireless Access Systems.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TS 102 177 V1.5.1 (2010-05)
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Alamouti, S.M.: "A Simple Transmit Diversity Technique for Wireless Communications", IEEE
journal on select areas in communications, Vol.16, No. 8, pages 1451-1458, October 1998.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
Base Station (BS): generalized equipment consisting of one or more Base Station Controllers and one or more Base
Station transceivers
channel coding: sequence composed of three steps; randomizer, forward error correction and interleaving
DL-MAP: structured data sequence that defined the mapping of the DL
DownLink (DL): direction from BS to SS
frequency offset index: index number identifying a particular carrier in an OFDM signal
NOTE: Frequency offset indices may be positive or negative and are counted relative to the DC carrier.
full duplex: equipment that is capable of transmitting and receiving at the same time
guard time: time at the beginning or end of each burst to allow power ramping up and down
half duplex: equipment that cannot transmit and receive at the same time
preamble: sequence of symbols with a given auto-correlation property assisting modem synchronization and channel
estimation
Receive-Transmit Transition Gap (RTG): time to switch from receive to transmit at the BS
Subscriber Station (SS): generalized equipment consisting of a Subscriber Station Controller and Subscriber Station
Transceiver
Transmit-Receive Transition Gap (TTG): time to switch from transmit to receive at the BS
UL MAP: MAC message scheduling UL bursts
UpLink (UL): direction from SS to BS
3.2 Symbols
For the purposes of the present document, the following symbols apply:
BW Nominal channel bandwidth (MHz)
F Sampling frequency (MHz)
sa
N Number of coded bits per OFDM symbol (on allocated subchannels)
cbps
N Nominal size of the FFT operator
FFT
N Number of carriers used to transport either data or pilots within a single OFDM symbol
used
R BW over sampling ratio
os
T Useful OFDM symbol time (s)
b
T Frame duration (ms)
F
ETSI

---------------------- Page: 7 ----------------------
8 ETSI TS 102 177 V1.5.1 (2010-05)
T OFDM symbol guard time or CP time (s)
g
T OFDM symbol time (s)
s
α Channel measurement averaging constant
avg
Δf Carrier spacing (Hz)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AAS Adaptive Antenna System
AWGN Average White Gaussian Noise
BER Bit Error Rate
BPSK Binary Phase Shift Keying
BS Base Station
BSID Base Station IDentification
BW BandWidth
CC Convolutional Coding
CCH Control subCHannel
CID Connection IDentifier
CINR Carrier to Interference Noise Ratio
CL Convergence Layer
CNR Carrier to Noise Ratio
CP Cyclic Prefix
CTC Convolutional Turbo Code
DC Direct Current
DCD Downlink Channel Descriptor
DIUC Downlink Interval Usage Code
DL DownLink
DLC Data Link Control
DLFP DownLink Frame Prefix
FCH Frame Control Header
FDD Frequency Division Duplexing
FEC Forward Error Correction
FFT Fast Fourier Transform
HCS Header Check Sequence
H-FDD Half duplex Frequency Division Duplexing
IE Information Element
IFFT Inverse Fast Fourier Transform
LSB least Significant Bit
MAC Media Access Control
MAN Metropolitan Area Network
MSB Most Significant Bit
OFDM Orthogonal Frequency Division Multiplexing
OFDMA Orthogonal Frequency Division Multiple Access
PDU Protocol Data Unit
PHY PHYsical
PMP Point-to-MultiPoint
PRBS Pseudo Random Binary Sequence
PS Physical Slot
QAM Quadrature Amplitude Modulation
QPSK Quadrature Phase Shift Keying
REQ REQuest
RF Radio Frequency
RMS Root Mean Square
RS Reed-Solomon
RS-CC Reed-Solomon / Convolutional Code
RSSI Received Signal Strength Indicator
RTG Receive-Transmit Transition Gap
Rx Receive
ETSI

---------------------- Page: 8 ----------------------
9 ETSI TS 102 177 V1.5.1 (2010-05)
SNR Signal to Noise Ratio
SS Subscriber Station
SSRTG Subscriber Station Receive Transmit Gap
STC Space Time Coding
TC Transmission Convergence
TDD Time Division Duplexing
TLV Type Length Value
TOs Transmission Opportunities
TTG Transmit-receive Transition Gap
Tx Transmit
UCD Uplink Channel Descriptor
UIUC Uplink Interval Usage Code
UL UpLink
XOR eXclusive OR
4 HiperMAN OFDM PHY
4.1 OFDM symbol description
An OFDM waveform is created by applying an Inverse-Fourier-transform to the source data. The resultant time
duration is referred to as the useful symbol time T . A copy of the last T μs of the useful symbol period, termed
b
g
Cyclic Prefix (CP), is prepended to enable the collection of multipath at the receiver, without loss of orthogonality
between the tones. The resulting waveform is termed the symbol time T . Figure 1 illustrates this structure.
s
Copy samples

Tg T
b

T
s

Figure 1: OFDM symbol time structure
The transmitter energy increases with the length of the CP while the receiver energy remains the same (the CP is
discarded), so there is a 10log (1− T /(T + T )) / log(10) dB loss in SNR. Using the CP, the samples required for
g b g
performing the FFT at the receiver can be taken anywhere over the length of the extended symbol. This provides
multipath immunity as well as a tolerance for symbol time synchronization errors.
On system initialization, the Base Station (BS) CP fraction (T / T ) shall be set to a specific value for use on the
g b
Downlink (DL). Once the BS is operational the CP value shall not be changed. On initialization, the
Subscriber Station (SS) shall search all possible values of CP until it finds the CP being used by the serving BS. The SS
shall use the same CP values determined in DL for the UL. Changing the CP value parameter at the BS through
(re)initialization forces all SS registered on that BS to re-synchronize.
In the frequency domain, each OFDM symbol is comprised of multiple carriers (see figure 2), which belong to one of
three types:
• Data carriers - for data transmission.
• Pilot carriers - for channel estimation and other purposes.
• Null carriers - for guard bands and the DC carrier.
ETSI

---------------------- Page: 9 ----------------------
10 ETSI TS 102 177 V1.5.1 (2010-05)
Guard
Pilot DC Data Guard

band
carriers carrier carriers band


Channel



Figure 2: OFDM symbol frequency structure
4.2 Transmitted signal
Equation 1 specifies the transmitted signal voltage s(t) to the antenna, as a function of time, during any OFDM symbol.
⎧ ⎫
⎪ k =N / 2 ⎪
used
2 jπkΔf()t−T
⎪ ⎪
2 jπf t g
c
s(t) = Re e c × e
⎨ ⎬ (1)
k
∑
⎪ ⎪
k=−N / 2
used
⎪ ⎪
k≠0
⎩ ⎭
where: t is the time elapsed since the beginning of the subject OFDM symbol, with 0< s
C is a complex number; the data to be transmitted on the carrier whose frequency offset index is k , during
k
the subject OFDM symbol. It specifies a point in a Quadrature Amplitude Modulation (QAM) constellation.
In the case of subchannelization, C is zero for all unallocated.
k
f is the RF carrier frequency, being the centre frequency of the intended RF frequency channel.
c
k is the frequency offset index.
The parameters of the transmitted OFDM signal, which shall be used, are given in table 1.
ETSI

---------------------- Page: 10 ----------------------
11 ETSI TS 102 177 V1.5.1 (2010-05)
Table 1: OFDM symbol parameters
Parameter Value
N
256
FFT
N 200
used
T
g
T 1/4, 1/8, 1/16, 1/32
b
Frequency offset indices of guard carriers -128, -127 to -101
+101, +102 to 127
Frequency offset indices of Pilots -88, -63, -38, -13, 13, 38, 63, 88
Subchannel Index Allocated frequency offset indices of carriers

  0b00001 {-100:-98, -37:-35, 1:3, 64:66}

  0b00010 {-38}
 0b00100 0b00011 {-97:-95, -34:-32, 4:6, 67:69}
  0b00101 {-94:-92, -31:-29, 7:9, 70:72}
  0b00110 {13}
0b01000  0b00111 {-91:-89, -28:-26, 10:12, 73:75}
{-87:-85, -50:-48, 14: 16, 51:53}
  0b01001
  0b01010 {-88}
 0b01100 0b01011 {-84,-82, -47:-45, 17: 19, 54:56}
  0b01101 {-81:-79, -44:-42, 20:22, 57:59}
  0b01110 {63}
0b10000  0b01111 {-78:-76, -41:-39, 23:25, 60:62}
  0b10001 {-75:-73, -12:-10, 26:28, 89:91}
  0b10010 {-13}
 0b10100 0b10011 {-72:-70, -9: -7, 29:31, 92:94}
  0b10101 {-69:-67, -6: -4, 32:34, 95:97}
  0b10110 {38}
0b11000  0b10111 {-66:-64, -3: -1, 35:37, 98:100}
  0b11001 {-62:-60, -25:-23, 39:41, 76:78}
  0b11010 {-63}
 0b11100 0b11011 {-59:-57, -22:-20, 42:44, 79:81}
  0b11101 {-56:-54, -19:-17, 45:47, 82:84}
  0b11110 {88}
  0b11111 {-53:-51, -16:-14, 48:50, 85:87}

NOTE: Pilot carriers are allocated only if two or more subchannels are allocated.

ETSI

---------------------- Page: 11 ----------------------
12 ETSI TS 102 177 V1.5.1 (2010-05)
Using the parameters as specified in table 1, the following relationships shall hold.
F = floor (R × BW / 8 000 ) × 8 000
sa os
R × BW
os
Δf =
N
FFT
1
T =
b
Δf
⎛T ⎞
g
T = ×T
⎜ ⎟
g b
T
b
⎝ ⎠
T = T + T
s b g
1
T =
sa
F
sa
F = R × BW
sa os
4.3 Channel coding
Channel coding is composed of three steps: randomization, forward error correction, and interleaving. They shall be
applied in this order at transmission. The complementary operations shall be applied in reverse order at reception.
4.3.1 Randomization
Data randomization is performed independently on each burst of uplink and downlink data (i.e. not on pilots and
preambles) on the subchannels in the frequency domain and OFDM symbols in the time domain. If the amount of data
to transmit does not fit exactly the amount of data allocated, padding of 0xFF ("1"s only) shall be added to the end of
the transmission block for the unused integer number of bytes, up to the amount of data allocated. For RS-CC and CC
encoded data, padding will be added to the end of the transmission block, up to the amount of data allocated minus one
byte, which shall be reserved for the introduction of a 0x00 tail byte by the FEC. For CTC, if implemented, padding will
be added to the end of the transmission block, up to the amount of data allocated.
1415
The Pseudo Random Binary Sequence (PRBS) generator shall be 1++x x as shown in figure 3. Each data byte to
be transmitted shall enter sequentially into the randomizer, most significant bit (MSB) first. The seed value shall be
used to calculate the randomization bits, which are combined in an XOR operation with the serialized bit stream of each
burst. The "data out" bits from the randomizer shall be applied to the FEC.

lsb msb

1
2 3 4 5 6 7 8 9 10 11 12 13 14 15

Data out

Data in


Figure 3: Data randomization PRBS
On the DL, the randomizer shall be re-initialized at the start of the FCH an
...