ETSI TS 138 141-2 V15.4.0 (2020-01)
5G; NR; Base Station (BS) conformance testing Part 2: Radiated conformance testing (3GPP TS 38.141-2 version 15.4.0 Release 15)
5G; NR; Base Station (BS) conformance testing Part 2: Radiated conformance testing (3GPP TS 38.141-2 version 15.4.0 Release 15)
RTS/TSGR-0438141-2vf40
General Information
Standards Content (Sample)
ETSI TS 138 141-2 V15.4.0 (2020-01)
TECHNICAL SPECIFICATION
5G;
NR;
Base Station (BS) conformance testing
Part 2: Radiated conformance testing
(3GPP TS 38.141-2 version 15.4.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 38.141-2 version 15.4.0 Release 15 1 ETSI TS 138 141-2 V15.4.0 (2020-01)
Reference
RTS/TSGR-0438141-2vf40
Keywords
5G
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 38.141-2 version 15.4.0 Release 15 2 ETSI TS 138 141-2 V15.4.0 (2020-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Legal Notice
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities. These shall be
interpreted as being references to the corresponding ETSI deliverables.
The cross reference between 3GPP and ETSI identities can be found under http://webapp.etsi.org/key/queryform.asp.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 38.141-2 version 15.4.0 Release 15 3 ETSI TS 138 141-2 V15.4.0 (2020-01)
Contents
Intellectual Property Rights . 2
Legal Notice . 2
Modal verbs terminology . 2
Foreword . 14
1 Scope . 15
2 References . 15
3 Definitions, symbols and abbreviations . 17
3.1 Definitions . 17
3.2 Symbols . 20
3.3 Abbreviations . 22
4 General radiated test conditions and declarations . 24
4.1 Measurement uncertainties and test requirements . 24
4.1.1 General . 24
4.1.2 Acceptable uncertainty of OTA Test System . 26
4.1.2.1 General . 26
4.1.2.2 Measurement of transmitter . 27
4.1.2.3 Measurement of receiver . 30
4.1.2.4 Measurement of performance requirement . 31
4.1.3 Interpretation of measurement results . 32
4.2 Radiated requirement reference points . 33
4.3 Base station classes . 34
4.4 Regional requirements . 34
4.5 BS configurations . 35
4.5.1 Transmit configurations . 35
4.5.2 Receive configurations . 36
4.5.3 Power supply options . 37
4.5.4 BS with integrated Iuant BS modem . 37
4.6 Manufacturer's declarations . 37
4.7 Test configurations . 46
4.7.1 General . 46
4.7.2 Test signal configurations . 46
4.7.2.1 Test signal used to build Test Configurations . 46
4.7.2.2 NRTC1: Contiguous spectrum operation . 46
4.7.2.2.1 NRTC1 generation . 46
4.7.2.2.2 NRTC1 power allocation . 47
4.7.2.3 NRTC2: Contiguous CA occupied bandwidth . 47
4.7.2.3.1 NRTC2 generation . 47
4.7.2.3.2 NRTC2 power allocation . 47
4.7.2.4 NRTC3: Non-contiguous spectrum operation . 48
4.7.2.4.1 NRTC3 generation . 48
4.7.2.4.2 NRTC3 power allocation . 48
4.7.2.5 NRTC4: Multi-band test configuration for full carrier allocation . 48
4.7.2.5.1 NRTC4 generation . 48
4.7.2.5.2 NRTC4 power allocation . 49
4.7.2.6 NRTC5: Multi-band test configuration with high PSD per carrier . 49
4.7.2.6.1 NRTC5 generation . 49
4.7.2.6.2 NRTC5 power allocation . 50
4.8 Applicability of requirements . 50
4.8.1 Requirement set applicability . 50
4.8.2 Applicability of test configurations for single-band RIB . 50
4.8.3 Applicability of test configurations for multi-band RIB . 51
4.9 RF channels and test models . 52
4.9.1 RF channels . 52
4.9.2 Test models . 53
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 38.141-2 version 15.4.0 Release 15 4 ETSI TS 138 141-2 V15.4.0 (2020-01)
4.9.2.1 General . 53
4.9.2.2 NR FR2 test models . 53
4.9.2.2.1 NR FR2 test model 1.1 (NR-FR2-TM1.1) . 55
4.9.2.2.2 NR FR2 test model 2 (NR-FR2-TM2) . 55
4.9.2.2.3 NR FR2 test model 3.1 (NR-FR2-TM3.1) . 56
4.9.2.3 Data content of physical channels and signals for NR-FR2-TM . 56
4.9.2.3.1 PDCCH . 56
4.9.2.3.2 PDSCH . 57
4.10 Requirements for contiguous and non-contiguous spectrum . 57
4.11 Requirements for BS capable of multi-band operation . 58
4.12 Co-location requirements . 58
4.12.1 General . 58
4.12.2 Co-location test antenna . 59
4.12.2.1 General . 59
4.12.2.2 Co-location test antenna characteristics . 59
4.12.2.3 Co-location test antenna alignment . 59
4.13 Format and interpretation of tests . 60
4.14 Reference coordinate system . 61
5 Operating bands and channel arrangement . 63
6 Radiated transmitter characteristics . 64
6.1 General . 64
6.2 Radiated transmit power . 64
6.2.1 Definition and applicability . 64
6.2.2 Minimum requirement . 64
6.2.3 Test purpose . 65
6.2.4 Method of test . 65
6.2.4.1 Initial conditions . 65
6.2.4.2 Procedure . 65
6.2.5 Test requirement . 66
6.3 OTA base station output power . 66
6.3.1 Definition and applicability . 66
6.3.2 Minimum requirement . 66
6.3.3 Test purpose . 66
6.3.4 Method of test . 67
6.3.4.1 Initial conditions . 67
6.3.4.2 Procedure . 67
6.3.5 Test requirement . 67
6.3.5.1 BS type 1-O . 67
6.3.5.2 BS type 2-O . 68
6.4 OTA output power dynamics . 68
6.4.1 General . 68
6.4.2 OTA RE power control dynamic range . 68
6.4.2.1 Definition and applicability . 68
6.4.2.2 Minimum requirement . 68
6.4.2.3 Method of test . 68
6.4.3 OTA total power dynamic range . 68
6.4.3.1 Definition and applicability . 68
6.4.3.2 Minimum requirement . 69
6.4.3.3 Test purpose . 69
6.4.3.4 Method of test . 69
6.4.3.4.1 Initial conditions . 69
6.4.3.4.2 Procedure . 69
6.4.3.5 Test requirement . 70
6.4.3.5.1 BS type 1-O . 70
6.4.3.5.2 BS type 2-O . 70
6.5 OTA transmit ON/OFF power. 71
6.5.1 OTA transmitter OFF power . 71
6.5.1.1 Definition and applicability . 71
6.5.1.2 Minimum requirement . 71
6.5.1.3 Test purpose . 71
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 38.141-2 version 15.4.0 Release 15 5 ETSI TS 138 141-2 V15.4.0 (2020-01)
6.5.1.4 Method of test . 71
6.5.1.5 Test requirements . 71
6.5.2 OTA transmitter transient period . 71
6.5.2.1 Definition and applicability . 71
6.5.2.2 Minimum requirement . 72
6.5.2.3 Test purpose . 72
6.5.2.4 Method of test . 72
6.5.2.4.1 Initial conditions . 72
6.5.2.4.2 Procedure . 73
6.5.2.4.2.1 General procedure . 73
6.5.2.4.2.2 BS type 1-O . 73
6.5.2.4.2.3 BS type 2-O . 73
6.5.2.5 Test requirements . 74
6.5.2.5.1 BS type 1-O . 74
6.5.2.5.2 BS type 2-O . 74
6.6 OTA transmitted signal quality . 74
6.6.1 General . 74
6.6.2 OTA frequency error . 74
6.6.2.1 Definition and applicability . 74
6.6.2.2 Minimum Requirement . 74
6.6.2.3 Test purpose . 74
6.6.2.4 Method of test . 74
6.6.2.4.1 Initial conditions . 75
6.6.2.5 Test Requirements . 75
6.6.3 OTA modulation quality . 75
6.6.3.1 Definition and applicability . 75
6.6.3.2 Minimum Requirement . 75
6.6.3.3 Test purpose . 75
6.6.3.4 Method of test . 75
6.6.3.4.1 Initial conditions . 75
6.6.3.4.2 Procedure . 76
6.6.3.5 Test requirements . 77
6.6.3.5.1 BS type 1-O . 77
6.6.3.5.2 BS type 2-O . 78
6.6.4 OTA time alignment error . 79
6.6.4.1 Definition and applicability . 79
6.6.4.2 Minimum requirement . 79
6.6.4.3 Test purpose . 79
6.6.4.4 Method of test . 79
6.6.4.4.1 Initial conditions . 79
6.6.4.4.2 Procedure . 80
6.6.4.5 Test Requirement . 80
6.6.4.5.1 BS type 1-O .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.