ETSI EN 305 200-2-3 V1.1.1 (2018-06)
Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 3: Mobile broadband access networks
Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 3: Mobile broadband access networks
DEN/ATTM-007
Dostop, terminali, prenos in multipleksiranje (ATTM) - Upravljanje z energijo - Operativna infrastruktura - Globalni ključni kazalniki uspešnosti (KPI) - 2. del: Posebne zahteve - 3. poddel: Mobilna širokopasovna dostopovna omrežja
Ta dokument določa zahteve za globalni KPI za upravljanje z energijo (KPIEM) in njegove temeljne ciljne KPI-je, ki naslavljajo naslednje cilje za širokopasovna omrežja z mobilnim dostopom:
• poraba energije;
• učinkovitost opravil;
• obnovljiva energija.
Zahteve so preslikane v splošne zahteve ETSI EN 305 200-1 [i.2].
Upravljanje z energijo omrežij z mobilnim dostopom je sestavljeno iz več neodvisnih slojev. Ta dokument naslavlja učinkovitost infrastruktur, ki podpirajo običajno delovanje gostujoče opreme IKT znotraj omrežja z mobilnim dostopom (npr. distribucija električne energije, okoljski nadzor, zaščita in varnost). Ta dokument ne naslavlja drugih slojev, kot so učinkovitost same opreme IKT, učinkovitost uporabe razpoložljive zmogljivosti procesorja in sloji, povezani s končno dostavljeno storitvijo (npr. potrebna moč obdelave glede na rezultat po elementih) ali prekrivni sloji (npr. poraba energije glede na rezultat po elementih).
Učinek na okolje in upravljanje različnih virov energije ne spadata na področje uporabe tega dokumenta.
V tem dokumentu:
• točka 4 opisuje energijske parametre za omrežja z mobilnim dostopom, skupaj z vključitvami/izključitvami različnih prispevanj k energiji;
• točka 5 določa zahteve za merjenje, izračun, razvrstitev in poročanje za KPIEM.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HåMDAccess, Terminals, Transmission and Multiplexing (ATTM) - Energy management - Operational infrastructures - Global KPIs - Part 2: Specific requirements - Sub-part 3: Mobile broadband access networks35.020Informacijska tehnika in tehnologija na splošnoInformation technology (IT) in general27.015VSORãQREnergy efficiency. Energy conservation in generalICS:Ta slovenski standard je istoveten z:ETSI EN 305 200-2-3 V1.1.1 (2018-06)SIST EN 305 200-2-3 V1.1.1:2018en01-september-2018SIST EN 305 200-2-3 V1.1.1:2018SLOVENSKI
STANDARD
SIST EN 305 200-2-3 V1.1.1:2018
ETSI EN 305 200-2-3 V1.1.1 (2018-06) Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 3: Mobile broadband access networks
EUROPEAN STANDARD SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)2
Reference DEN/ATTM-007 Keywords broadband, energy management, ICT, sustainability ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)3Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 7 Introduction . 7 1 Scope . 9 2 References . 9 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 12 3.3 Abbreviations . 12 4 Energy management of mobile access networks . 13 4.1 General . 13 4.1.1 Mobile broadband access networks . 13 4.1.2 Mobile access network technologies. 13 4.1.3 Energy consumption . 14 4.1.4 Task effectiveness . 15 5 Global KPI (KPIEM) for mobile access networks . 15 5.1 General . 15 5.1.1 Global KPI (KPIEM) for mobile access networks . 15 5.1.2 Objective KPIs . 16 5.1.2.1 Energy consumption (KPIEC) . 16 5.1.2.2 Task effectiveness (KPITE) . 16 5.1.2.2.1 General . 16 5.1.2.3 Energy re-use . 16 5.1.2.4 Renewable energy (KPIREN) . 17 5.2 Scale . 17 5.3 Utilization and evolution . 17 5.4 Definition of boundaries . 18 5.5 Formulae. 18 5.5.1 Global KPI (KPIEM) for mobile access networks . 18 5.5.1.1 General . 18 5.5.1.2 Definition of terms . 18 5.5.1.3 Clarity . 18 5.5.1.4 Criteria . 18 5.5.2 Objective KPI for mobile access networks . 19 5.5.2.1 Energy consumption (KPIEC) . 19 5.5.2.1.1 Formula . 19 5.5.2.1.2 Definitions of terms . 19 5.5.2.1.3 Clarity . 19 5.5.2.1.4 Criteria . 19 5.5.2.2 Task Effectiveness (KPITE) . 20 5.5.2.2.1 Formula . 20 5.5.2.2.2 Definitions of terms . 20 5.5.2.2.3 Clarity . 20 5.5.2.2.4 Criteria . 20 5.5.2.3 Renewable energy (KPIREN) . 20 5.5.2.3.1 Formula . 20 5.5.2.3.2 Definitions of terms . 20 5.5.2.3.3 Clarity . 20 5.5.2.3.4 Criteria . 21 5.6 Measurement points and procedures . 21 SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)45.6.1 Objective KPIs for mobile access networks . 21 5.6.1.1 Energy consumption (KPIEC) . 21 5.6.1.1.1 Measurement points . 21 5.6.1.1.2 Measurement procedures . 21 5.6.1.2 Task effectiveness (KPITE) . 21 5.6.1.2.1 Measurement points . 21 5.6.1.2.2 Measurement procedures . 21 5.6.1.3 Renewable energy (KPIREN) . 22 5.6.1.3.1 Measurement points . 22 5.6.1.3.2 Measurement procedures . 22 5.7 Reporting . 22 Annex A (informative): History of network schematics . 23 History . 24
SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)5List of figures Figure 1: Updated schematic of fixed and mobile communication networks .13 Figure 2: Mobile access network implementations .14 Figure 3: Schematic of mobile access network energy consumption .15 Figure A.1: Schematic of fixed and mobile communication networks (June 2011) .23
SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)6Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 2, sub part 3 of a multi-part deliverable covering Global Key Performance Indicators for energy management of operational broadband deployment infrastructures as identified below: Part 1: "General requirements"; Part 2: "Specific requirements"; Sub-part 1: "ICT Sites"; Sub-part 2: "Fixed broadband access networks"; Sub-part 3: "Mobile broadband access networks"; Part 3: "ICT Sites"; Part 4: "Design assessments".
National transposition dates Date of adoption of this EN: 23 May 2018 Date of latest announcement of this EN (doa): 31 August 2018 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
28 February 2019 Date of withdrawal of any conflicting National Standard (dow): 28 February 2019
SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)7Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction Energy costs continue to rise, a trend that will continue in the future, while broadband penetration is introducing new active equipment to the network architecture. In this context, and to reflect other environmental aspects of sustainability, it is vital that the main telecommunication operators implement effective general engineering of fixed and mobile broadband networks and sites provisioning, managing or using those networks (i.e. ICT sites) in order to respond to critical issues of energy consumption while proposing essential solutions to broadband deployment. To guide this process, it is essential that metrics are defined, termed Global Key Performance Indicators (KPIs), that enable energy usage to be managed more effectively. The Global Key Performance Indicators of the ETSI EN 305 200 [i.1] series address operational infrastructures and do not consider design or operation of individual components comprising those infrastructures. The ETSI EN 305 200 [i.1] series of standards comprises: • ETSI EN 305 200-1 [i.2]: a generic requirements document addressing Global KPIs for operational infrastructures. • A sub-series ETSI EN 305 200-2 that defines the Global KPIs, and drives energy management targets, for specific operational networks and sites and which describes how the Global KPIs are to be applied (which may be used to support future regulatory objectives): - ETSI EN 305 200-2-1 [i.3]: ICT sites; - ETSI EN 305 200-2-2 [i.4]: Fixed broadband access networks; NOTE: Excluding cable access networks. - ETSI EN 305 200-2-3 (the present document): Mobile broadband access networks. The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain information on values that have been used by certain organizations. • A sub-series ETSI EN 305 200-3 [i.5] including ETSI EN 305 200-3-1 [i.6] that defines particular implementations of Global KPIs within ICT sites based on the requirements of ETSI EN 305 200-2-1[i.3], and which may define levels of performance to simplify and provide clearer understanding of Global KPIs allowing the evaluation of performance of energy use management in ICT sites. The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain information on values that have been used by certain organizations. • A sub-series ETSI EN 305 200-4 including ETSI EN 305 200-4-4 [i.7] that defines design assessments of Global KPIs, and drives energy management targets, for specific operational networks and sites and which describes how the Global KPIs are to be applied (which may be used to support future regulatory objectives). These standards may be considered to be a contribution to the application of ISO 50001 [i.8] in relation to the development of policy for the continuous improvement of energy management and will accelerate. • The availability of operational infrastructure architectures and network implementations that use energy more efficiently. • The definition and attainment objectives for other environmental aspects of sustainability for operational broadband networks. SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)8The present document specifies the requirements for a Global KPI for energy management (KPIEM) and their underpinning Objective KPIs for the mobile access networks of broadband deployment. The requirements are mapped to the general requirements of ETSI EN 305 200-1 [i.2]. SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)91 Scope The present document specifies the requirements for a Global KPI for energy management (KPIEM) and their underpinning Objective KPIs addressing the following objectives for the mobile access networks of broadband deployment: • energy consumption; • task effectiveness; • renewable energy. The requirements are mapped to the general requirements of ETSI EN 305 200-1 [i.2]. Energy management of mobile access networks comprises a number of independent layers. The present document addresses performance of infrastructures that supports the normal function of hosted ICT equipment within the mobile access network (e.g. power distribution, environmental control, security and safety).The present document does not address other layers such as performance of ICT equipment itself, performance of usage of available processing power, and layers related to final service delivered (e.g. processing power required per itemized outcome) or overlay layers (e.g. energy consumption required per itemized outcome). The environmental impact and management of different energy sources are outside the scope of the present document. Within the present document: • clause 4 describes the energy parameters for mobile access networks together with inclusions/exclusions of different energy contributions; • clause 5 specifies the requirements for measurement, calculation, classification and reporting of KPIEM. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at https://docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] ETSI EN 303 472: "Environmental Engineering (EE); Energy Efficiency measurement methodology and metrics for RAN equipment". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)10[i.1] ETSI EN 305 200 series: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs". [i.2] ETSI EN 305 200-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 1: General requirements". [i.3] ETSI EN 305 200-2-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 1: ICT Sites". [i.4] ETSI EN 305 200-2-2: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 2: Fixed broadband access networks". [i.5] ETSI EN 305 200-3: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 3: ICT Sites". [i.6] ETSI EN 305 200-3-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 3: ICT Sites; Sub-part 1: DCEM". [i.7] ETSI EN 305 200-4-4: "Integrated broadband cable telecommunication networks (CABLE); Energy management; Operational infrastructures; Global KPIs; Part 4: Design assessments; Sub-part 4: Cable Access Networks". [i.8] ISO 50001: "Energy management systems - Requirements with guidance for use". [i.9] M/462 Standardisation mandate addressed to CEN, CENELEC and ETSI in the field of ICT to enable efficient energy use in fixed and mobile information and communication networks. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: access network: functional elements (that is equipment and infrastructure) that enable communication between an Operator Site (OS) and a customer network backhaul infrastructure: functional elements connecting a base station to an operator site cable access network: access network provided by cable operators comprising optical fibre and metallic cabling providing direct connection to customer premises Customer Premises (CP): any location which is the sole responsibility of the customer Base Station (BS): Network Telecommunications Equipment (NTE) which serves one or more cells within a coverage area of a mobile access network Base Station (BS) site: Network Distribution Node (NDN) which accommodates a Base Station (BS) core network: functional elements (that is equipment and infrastructure) that enable communication between Operator Sites (OSs) or equivalent ICT sites energy consumption: total consumption of energy by an operational infrastructure energy management: combination of reduced energy consumption and increased task effectiveness, re-use of energy and use of renewable energy extended base station site: base station site which is served under typical operating conditions by on-site generation of electricity Global KPI: KPI, combining two or more Objective KPIs, which reflects the overall energy management performance of an operational infrastructure SIST EN 305 200-2-3 V1.1.1:2018
ETSI ETSI EN 305 200-2-3 V1.1.1 (2018-06)11ICT equipment: equipment providing data storage, processing and transport services NOTE: A combination of Information Technology Equipment and Network Telecommunications Equipment. ICT site: site containing structures or group of structures dedicated to the accommodation, interconnection and operation of ICT equipment together with all the facilities and infrastructures for power distribution and environmental control together with the necessary levels of resilience and security required to provide the desired service availability Information Technology Equipment (ITE): equipment providing data storage, processing and transport services for subsequent distribution by Network Telecommunications Equipment (NTE) mobile access network: telecommunications network in which the access to the network (connection between user equipment and network) is implemented over the air interface Network Distribution Node (NDN): grouping of Network Telecommunications Equipment (NTE) equipment within the boundaries of an access network providing distribution of service from an Operator Site (OS) NOTE: Where all the Network Telecommunications Equipment (NTE) at a given location is under common governance, any supporting infrastructure for power distribution and environmental control together with the necessary levels of resilience and security required to provide the desired service availability is included as part of the NDN. Network Functions Virtualisation (NFV): principle of separating network functions from the hardware they run on by using virtual hardware abstraction Network Telecommunications Equipment (NTE): equipment between the boundaries of, and dedicated to providing connection to, core and/or access networks Objective KPI: KPI assessing one of the objectives of operational energy performance which is subsequently used to define a Global KPI for energy management operational infrastructure: combination of ICT equipment together with the power supply and environmental control systems necessary to ensure provision of service Operator Site (OS): premises accommodating Network Telecommunications Equipment (NTE) providing direct connection to the core and access networks and which may also accommodate Information Technology Equipment (ITE) NOTE 1: An operator site that is only connected to the core network is considered as a network data centre. NOTE 2: An operator site of a cable access network may be termed a local head-end. Radio Access Network (RAN): telecommunications network in which the access to the network (connection between user equipment and network) is implemented over the air interface NOTE: Part of GERAN, UTRAN or E-UTRA networks defined by 3GPP. renewable energy: energy from renewable sources" as energy from renewable non-fossil sources, namely wind, solar, aerothermal, geothermal, hydrothermal and ocean energy, hydropower, biomass, landfill gas, sewage treatment plant gas and biogases Repeater (R): device with two RF ports, both of which are intended to be connected to antennas, which is capable of receiving, amplifying and transmitting simultaneously in one direction a signal in a base station's tr
...
ETSI EN 305 200-2-3 V1.1.1 (2018-06)
EUROPEAN STANDARD
Access, Terminals, Transmission and Multiplexing (ATTM);
Energy management;
Operational infrastructures;
Global KPIs;
Part 2: Specific requirements;
Sub-part 3: Mobile broadband access networks
---------------------- Page: 1 ----------------------
2 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
Reference
DEN/ATTM-007
Keywords
broadband, energy management, ICT,
sustainability
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Energy management of mobile access networks . 13
4.1 General . 13
4.1.1 Mobile broadband access networks . 13
4.1.2 Mobile access network technologies. 13
4.1.3 Energy consumption . 14
4.1.4 Task effectiveness . 15
5 Global KPI (KPI ) for mobile access networks . 15
EM
5.1 General . 15
5.1.1 Global KPI (KPI ) for mobile access networks . 15
EM
5.1.2 Objective KPIs . 16
5.1.2.1 Energy consumption (KPI ) . 16
EC
5.1.2.2 Task effectiveness (KPI ) . 16
TE
5.1.2.2.1 General . 16
5.1.2.3 Energy re-use . 16
5.1.2.4 Renewable energy (KPI ) . 17
REN
5.2 Scale . 17
5.3 Utilization and evolution . 17
5.4 Definition of boundaries . 18
5.5 Formulae. 18
5.5.1 Global KPI (KPI ) for mobile access networks . 18
EM
5.5.1.1 General . 18
5.5.1.2 Definition of terms . 18
5.5.1.3 Clarity . 18
5.5.1.4 Criteria . 18
5.5.2 Objective KPI for mobile access networks . 19
5.5.2.1 Energy consumption (KPI ) . 19
EC
5.5.2.1.1 Formula . 19
5.5.2.1.2 Definitions of terms . 19
5.5.2.1.3 Clarity . 19
5.5.2.1.4 Criteria . 19
5.5.2.2 Task Effectiveness (KPI ) . 20
TE
5.5.2.2.1 Formula . 20
5.5.2.2.2 Definitions of terms . 20
5.5.2.2.3 Clarity . 20
5.5.2.2.4 Criteria . 20
5.5.2.3 Renewable energy (KPI ) . 20
REN
5.5.2.3.1 Formula . 20
5.5.2.3.2 Definitions of terms . 20
5.5.2.3.3 Clarity . 20
5.5.2.3.4 Criteria . 21
5.6 Measurement points and procedures . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
5.6.1 Objective KPIs for mobile access networks . 21
5.6.1.1 Energy consumption (KPI ) . 21
EC
5.6.1.1.1 Measurement points . 21
5.6.1.1.2 Measurement procedures . 21
5.6.1.2 Task effectiveness (KPI ) . 21
TE
5.6.1.2.1 Measurement points . 21
5.6.1.2.2 Measurement procedures . 21
5.6.1.3 Renewable energy (KPI ) . 22
REN
5.6.1.3.1 Measurement points . 22
5.6.1.3.2 Measurement procedures . 22
5.7 Reporting . 22
Annex A (informative): History of network schematics . 23
History . 24
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
List of figures
Figure 1: Updated schematic of fixed and mobile communication networks .13
Figure 2: Mobile access network implementations .14
Figure 3: Schematic of mobile access network energy consumption .15
Figure A.1: Schematic of fixed and mobile communication networks (June 2011) .23
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 2, sub part 3 of a multi-part deliverable covering Global Key Performance Indicators for
energy management of operational broadband deployment infrastructures as identified below:
Part 1: "General requirements";
Part 2: "Specific requirements";
Sub-part 1: "ICT Sites";
Sub-part 2: "Fixed broadband access networks";
Sub-part 3: "Mobile broadband access networks";
Part 3: "ICT Sites";
Part 4: "Design assessments".
National transposition dates
Date of adoption of this EN: 23 May 2018
Date of latest announcement of this EN (doa): 31 August 2018
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2019
Date of withdrawal of any conflicting National Standard (dow): 28 February 2019
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Energy costs continue to rise, a trend that will continue in the future, while broadband penetration is introducing new
active equipment to the network architecture. In this context, and to reflect other environmental aspects of
sustainability, it is vital that the main telecommunication operators implement effective general engineering of fixed
and mobile broadband networks and sites provisioning, managing or using those networks (i.e. ICT sites) in order to
respond to critical issues of energy consumption while proposing essential solutions to broadband deployment. To guide
this process, it is essential that metrics are defined, termed Global Key Performance Indicators (KPIs), that enable
energy usage to be managed more effectively.
The Global Key Performance Indicators of the ETSI EN 305 200 [i.1] series address operational infrastructures and do
not consider design or operation of individual components comprising those infrastructures.
The ETSI EN 305 200 [i.1] series of standards comprises:
• ETSI EN 305 200-1 [i.2]: a generic requirements document addressing Global KPIs for operational
infrastructures.
• A sub-series ETSI EN 305 200-2 that defines the Global KPIs, and drives energy management targets, for
specific operational networks and sites and which describes how the Global KPIs are to be applied (which may
be used to support future regulatory objectives):
- ETSI EN 305 200-2-1 [i.3]: ICT sites;
- ETSI EN 305 200-2-2 [i.4]: Fixed broadband access networks;
NOTE: Excluding cable access networks.
- ETSI EN 305 200-2-3 (the present document): Mobile broadband access networks.
The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain
information on values that have been used by certain organizations.
• A sub-series ETSI EN 305 200-3 [i.5] including ETSI EN 305 200-3-1 [i.6] that defines particular
implementations of Global KPIs within ICT sites based on the requirements of ETSI EN 305 200-2-1[i.3], and
which may define levels of performance to simplify and provide clearer understanding of Global KPIs
allowing the evaluation of performance of energy use management in ICT sites.
The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain
information on values that have been used by certain organizations.
• A sub-series ETSI EN 305 200-4 including ETSI EN 305 200-4-4 [i.7] that defines design assessments of
Global KPIs, and drives energy management targets, for specific operational networks and sites and which
describes how the Global KPIs are to be applied (which may be used to support future regulatory objectives).
These standards may be considered to be a contribution to the application of ISO 50001 [i.8] in relation to the
development of policy for the continuous improvement of energy management and will accelerate.
• The availability of operational infrastructure architectures and network implementations that use energy more
efficiently.
• The definition and attainment objectives for other environmental aspects of sustainability for operational
broadband networks.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
The present document specifies the requirements for a Global KPI for energy management (KPI ) and their
EM
underpinning Objective KPIs for the mobile access networks of broadband deployment. The requirements are mapped
to the general requirements of ETSI EN 305 200-1 [i.2].
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
1 Scope
The present document specifies the requirements for a Global KPI for energy management (KPI ) and their
EM
underpinning Objective KPIs addressing the following objectives for the mobile access networks of broadband
deployment:
• energy consumption;
• task effectiveness;
• renewable energy.
The requirements are mapped to the general requirements of ETSI EN 305 200-1 [i.2].
Energy management of mobile access networks comprises a number of independent layers. The present document
addresses performance of infrastructures that supports the normal function of hosted ICT equipment within the mobile
access network (e.g. power distribution, environmental control, security and safety).The present document does not
address other layers such as performance of ICT equipment itself, performance of usage of available processing power,
and layers related to final service delivered (e.g. processing power required per itemized outcome) or overlay layers
(e.g. energy consumption required per itemized outcome).
The environmental impact and management of different energy sources are outside the scope of the present document.
Within the present document:
• clause 4 describes the energy parameters for mobile access networks together with inclusions/exclusions of
different energy contributions;
• clause 5 specifies the requirements for measurement, calculation, classification and reporting of KPI .
EM
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 303 472: "Environmental Engineering (EE); Energy Efficiency measurement
methodology and metrics for RAN equipment".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
[i.1] ETSI EN 305 200 series: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs".
[i.2] ETSI EN 305 200-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 1: General requirements".
[i.3] ETSI EN 305 200-2-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 1:
ICT Sites".
[i.4] ETSI EN 305 200-2-2: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 2:
Fixed broadband access networks".
[i.5] ETSI EN 305 200-3: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 3: ICT Sites".
[i.6] ETSI EN 305 200-3-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 3: ICT Sites; Sub-part 1: DCEM".
[i.7] ETSI EN 305 200-4-4: "Integrated broadband cable telecommunication networks (CABLE);
Energy management; Operational infrastructures; Global KPIs; Part 4: Design assessments;
Sub-part 4: Cable Access Networks".
[i.8] ISO 50001: "Energy management systems - Requirements with guidance for use".
[i.9] M/462 Standardisation mandate addressed to CEN, CENELEC and ETSI in the field of ICT to
enable efficient energy use in fixed and mobile information and communication networks.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
access network: functional elements (that is equipment and infrastructure) that enable communication between an
Operator Site (OS) and a customer network
backhaul infrastructure: functional elements connecting a base station to an operator site
cable access network: access network provided by cable operators comprising optical fibre and metallic cabling
providing direct connection to customer premises
Customer Premises (CP): any location which is the sole responsibility of the customer
Base Station (BS): Network Telecommunications Equipment (NTE) which serves one or more cells within a coverage
area of a mobile access network
Base Station (BS) site: Network Distribution Node (NDN) which accommodates a Base Station (BS)
core network: functional elements (that is equipment and infrastructure) that enable communication between Operator
Sites (OSs) or equivalent ICT sites
energy consumption: total consumption of energy by an operational infrastructure
energy management: combination of reduced energy consumption and increased task effectiveness, re-use of energy
and use of renewable energy
extended base station site: base station site which is served under typical operating conditions by on-site generation of
electricity
Global KPI: KPI, combining two or more Objective KPIs, which reflects the overall energy management performance
of an operational infrastructure
ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 305 200-2-3 V1.1.1 (2018-06)
ICT equipment: equipment providing data storage, processing and transport services
NOTE: A combination of Information Technology Equipment and Network Telecommunications Equipment.
ICT site: site containing structures or group of structures dedicated to the accommodation, interconnection and
operation of ICT equipment together with all the facilities and infrastructures for power distribution and environmental
control together with the necessary levels of resilience and security required to provide the desired service availability
Information Technology Equipment (ITE): equipment providing data storage, processing and transport services for
subsequent distribution by Network Telecommunications Equipment (NTE)
mobile access network: telecommunications network in which the access to the network (connection between user
equipment and network) is implemented over the air interface
Network Distribution Node (NDN): grouping of Network Telecommunications Equipment (NTE) equipment within
the boundaries of an access network providing distribution of service from an Operator Site (OS)
NOTE: Where all the Network Telecommunications Equipment (NTE) at a given location is under common
governance, any supporting infrastructure for power distribution and environmental control together with
the necessary levels of resilience and security required to provide the desired service availability is
included as part of the NDN.
Network Functions Virtualisation (NFV): principle of separating network functions from the hardware they run on by
using virtual hardware abstraction
Network Telecommunications Equipment (NTE): equipment between the boundaries of, and dedicated to providing
connection to, core and/or access networks
Objective KPI: KPI assessing one of the objectives of operational energy performance which is subsequently used to
define a Global KPI for energy management
operational infrastructure: combination of ICT equipment together with the power supply and environmental control
systems necessary to ensure provision of service
Operator Site (OS): premises accommodating Network Telecommunications Equipment (NTE) providing direct
connection to the core and access networks and which may also accommodate Information Technology Equipment
(ITE)
NOTE 1: An operator site that is only connected to the core network is considered as a network data centre.
NOTE 2: An operator site of a cable access network may be termed a local head-end.
Radio Access Network (RAN): telecommunications network in which the access to the network (connection between
user equipment and network) is implemented over the air interface
NOTE: Part of GERAN, UTRAN or E-UTRA networks defined by 3GPP.
renewable energy: energy from renewable sources" as energy from renewable non-fossil sources, namely wind, solar,
aerothermal, geothermal, hydrothermal and ocean energy, hydropower, biomass, landfill gas, sewage treatment plant
gas and biogases
Repeater (R): device with two RF ports, both of which are intended to be connected to antennas, which is capable of
receiving, amplifying and transmitting simultaneously in one direction a signal in a base station's transmit band and in
the other direction
...
Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
EUROPEAN STANDARD
Access, Terminals, Transmission and Multiplexing (ATTM);
Energy management; Operational infrastructures; Global KPIs;
Part 2: Specific requirements;
Sub-part 3: Mobile broadband access networks
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
Reference
DEN/ATTM-007
Keywords
broadband, energy management, ICT,
sustainability
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Energy management of mobile access networks . 13
4.1 General . 13
4.1.1 Mobile broadband access networks . 13
4.1.2 Mobile access network technologies. 13
4.1.3 Energy consumption . 14
4.1.4 Task effectiveness . 15
5 Global KPI (KPI ) for mobile access networks . 15
EM
5.1 General . 15
5.1.1 Global KPI (KPI ) for mobile access networks . 15
EM
5.1.2 Objective KPIs . 16
5.1.2.1 Energy consumption (KPI ) . 16
EC
5.1.2.2 Task effectiveness (KPI ) . 16
TE
5.1.2.2.1 General . 16
5.1.2.3 Energy re-use . 16
5.1.2.4 Renewable energy (KPI ) . 17
REN
5.2 Scale . 17
5.3 Utilization and evolution . 17
5.4 Definition of boundaries . 18
5.5 Formulae. 18
5.5.1 Global KPI (KPI ) for mobile access networks . 18
EM
5.5.1.1 General . 18
5.5.1.2 Definition of terms . 18
5.5.1.3 Clarity . 18
5.5.1.4 Criteria . 18
5.5.2 Objective KPI for mobile access networks . 19
5.5.2.1 Energy consumption (KPI ) . 19
EC
5.5.2.1.1 Formula . 19
5.5.2.1.2 Definitions of terms . 19
5.5.2.1.3 Clarity . 19
5.5.2.1.4 Criteria . 19
5.5.2.2 Task Effectiveness (KPI ) . 20
TE
5.5.2.2.1 Formula . 20
5.5.2.2.2 Definitions of terms . 20
5.5.2.2.3 Clarity . 20
5.5.2.2.4 Criteria . 20
5.5.2.3 Renewable energy (KPI ) . 20
REN
5.5.2.3.1 Formula . 20
5.5.2.3.2 Definitions of terms . 20
5.5.2.3.3 Clarity . 20
5.5.2.3.4 Criteria . 21
5.6 Measurement points and procedures . 21
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
5.6.1 Objective KPIs for mobile access networks . 21
5.6.1.1 Energy consumption (KPI ) . 21
EC
5.6.1.1.1 Measurement points . 21
5.6.1.1.2 Measurement procedures . 21
5.6.1.2 Task effectiveness (KPI ) . 21
TE
5.6.1.2.1 Measurement points . 21
5.6.1.2.2 Measurement procedures . 21
5.6.1.3 Renewable energy (KPI ) . 22
REN
5.6.1.3.1 Measurement points . 22
5.6.1.3.2 Measurement procedures . 22
5.7 Reporting . 22
Annex A (informative): History of network schematics . 23
History . 24
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
List of figures
Figure 1: Updated schematic of fixed and mobile communication networks .13
Figure 2: Mobile access network implementations .14
Figure 3: Schematic of mobile access network energy consumption .15
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 2, sub part 3 of a multi-part deliverable covering Global Key Performance Indicators for
energy management of operational broadband deployment infrastructures as identified below:
Part 1: "General requirements";
Part 2: "Specific requirements";
Sub-part 1: "ICT sites";
Sub-part 2: "Fixed broadband access networks";
Sub-part 3: "Mobile broadband access networks";
Part 3: "ICT sites";
Part 4: "Design assessments".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Energy costs continue to rise, a trend that will continue in the future, while broadband penetration is introducing new
active equipment to the network architecture. In this context, and to reflect other environmental aspects of
sustainability, it is vital that the main telecommunication operators implement effective general engineering of fixed
and mobile broadband networks and sites provisioning, managing or using those networks (i.e. ICT sites) in order to
respond to critical issues of energy consumption while proposing essential solutions to broadband deployment. To guide
this process, it is essential that metrics are defined, termed Global Key Performance Indicators (KPIs), that enable
energy usage to be managed more effectively.
The Global Key Performance Indicators of the ETSI EN 305 200 [i.1] series address operational infrastructures and do
not consider design or operation of individual components comprising those infrastructures.
The ETSI EN 305 200 [i.1] series of standards comprises:
• ETSI EN 305 200-1 [i.2]: a generic requirements document addressing Global KPIs for operational
infrastructures;
• a sub-series ETSI EN 305 200-2 that defines the Global KPIs, and drives energy management targets, for
specific operational networks and sites and which describes how the Global KPIs are to be applied (which may
be used to support future regulatory objectives):
- ETSI EN 305 200-2-1 [i.3]: ICT sites;
- ETSI EN 305 200-2-2 [i.4]: Fixed broadband access networks;
NOTE: Excluding cable access networks.
- ETSI EN 305 200-2-3 (the present document): Mobile broadband access networks.
The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain
information on values that have been used by certain organizations.
• a sub-series ETSI EN 305 200-3 [i.5] including ETSI EN 305 200-3-1 [i.6] that defines particular
implementations of Global KPIs within ICT sites based on the requirements of ETSI EN 305 200-2-1[i.3], and
which may define levels of performance to simplify and provide clearer understanding of Global KPIs
allowing the evaluation of performance of energy use management in ICT sites.
The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain
information on values that have been used by certain organizations.
• a sub-series ETSI EN 305 200-4 including ETSI EN 305 200-4-4 [i.7] that defines design assessments of
Global KPIs, and drives energy management targets, for specific operational networks and sites and which
describes how the Global KPIs are to be applied (which may be used to support future regulatory objectives).
These standards may be considered to be a contribution to the application of ISO 50001 [i.8] in relation to the
development of policy for the continuous improvement of energy management and will accelerate.
• the availability of operational infrastructure architectures and network implementations that use energy more
efficiently;
• the definition and attainment objectives for other environmental aspects of sustainability for operational
broadband networks.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
The present document specifies the requirements for a Global KPI for energy management (KPI ) and their
EM
underpinning Objective KPIs for the mobile access networks of broadband deployment. The requirements are mapped
to the general requirements of ETSI EN 305 200-1 [i.2].
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
1 Scope
The present document specifies the requirements for a Global KPI for energy management (KPIEM) and their
underpinning Objective KPIs addressing the following objectives for the mobile access networks of broadband
deployment:
• energy consumption;
• task effectiveness;
• renewable energy.
The requirements are mapped to the general requirements of ETSI EN 305 200-1 [i.2].
Energy management of mobile access networks comprises a number of independent layers. The present document
addresses performance of infrastructures that supports the normal function of hosted ICT equipment within the mobile
access network (e.g. power distribution, environmental control, security and safety).The present document does not
address other layers such as performance of ICT equipment itself, performance of usage of available processing power,
and layers related to final service delivered (e.g. processing power required per itemized outcome) or overlay layers
(e.g. energy consumption required per itemized outcome).
The environmental impact and management of different energy sources are outside the scope of the present document.
Within the present document:
• clause 4 describes the energy parameters for mobile access networks together with inclusions/exclusions of
different energy contributions;
• clause 5 specifies the requirements for measurement, calculation, classification and reporting of KPI .
EM
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
[1] ETSI EN 303 472: "Environmental Engineering (EE); Energy Efficiency measurement
methodology and metrics for RAN equipment".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
[i.1] ETSI EN 305 200 series : "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs".
[i.2] ETSI EN 305 200-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 1: General requirements".
[i.3] ETSI EN 305 200-2-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 1:
ICT Sites".
[i.4] ETSI EN 305 200-2-2: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 2:
Fixed broadband access networks".
[i.5] ETSI EN 305 200-3: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 3: ICT Sites".
[i.6] ETSI EN 305 200-3-1: "Access, Terminals, Transmission and Multiplexing (ATTM); Energy
management; Operational infrastructures; Global KPIs; Part 3: ICT Sites; Sub-part 1: DCEM".
[i.7] ETSI EN 305 200-4-4: "Integrated broadband cable telecommunication networks (CABLE);
Energy management; Operational infrastructures; Global KPIs; Part 4: Design assessments;
Sub-part 4: Cable Access Networks".
[i.8] ISO 50001: "Energy management systems - Requirements with guidance for use".
[i.9] M/462 Standardisation mandate addressed to CEN, CENELEC and ETSI in the field of ICT to
enable efficient energy use in fixed and mobile information and communication networks.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
access network: functional elements (that is equipment and infrastructure) that enable communication between an
Operator Site (OS) and a customer network
backhaul infrastructure: functional elements connecting a base station to an operator site
cable access network: access network provided by cable operators comprising optical fibre and metallic cabling
providing direct connection to customer premises
Customer Premises (CP): any location which is the sole responsibility of the customer
Base Station (BS) site: Network Distribution Node (NDN) which accommodates a Base Station (BS)
Base Station (BS): Network Telecommunications Equipment (NTE) which serves one or more cells within a coverage
area of a mobile access network
core network: functional elements (that is equipment and infrastructure) that enable communication between Operator
Sites (OSs) or equivalent ICT sites
energy consumption: total consumption of energy by an operational infrastructure
energy management: combination of reduced energy consumption and increased task effectiveness, re-use of energy
and use of renewable energy
extended base station site: base station site which is served under typical operating conditions by on-site generation of
electricity
Global KPI: KPI, combining two or more Objective KPIs, which reflects the overall energy management performance
of an operational infrastructure
ETSI
---------------------- Page: 10 ----------------------
11 Draft ETSI EN 305 200-2-3 V1.1.0 (2018-02)
ICT equipment: equipment providing data storage, processing and transport services
NOTE: A combination of Information Technology Equipment and Network Telecommunications Equipment.
ICT site: site containing structures or group of structures dedicated to the accommodation, interconnection and
operation of ICT equipment together with all the facilities and infrastructures for power distribution and environmental
control together with the necessary levels of resilience and security required to provide the desired service availability
Information Technology Equipment (ITE): equipment providing data storage, processing and transport services for
subsequent distribution by Network Telecommunications Equipment (NTE)
mobile access network: telecommunications network in which the access to the network (connection between user
equipment and network) is implemented over the air interface
Network Distribution Node (NDN): grouping of Network Telecommunications Equipment (NTE) equipment within
the boundaries of an access network providing distribution of service from an Operator Site (OS)
NOTE: Where all the Network Telecommunications Equipment (NTE) at a given location is under common
governance, any supporting infrastructure for power distribution and environmental control together with
the necessary levels of resilience and security required to provide the desired service availability is
included as part of the NDN.
Network Functions Virtualisation (NFV): principle of separating network functions from the hardware they run on by
using virtual hardware abstraction
Network Telecommunications Equipment (NTE): equipment between the boundaries of, and dedicated to providing
connection to, core and/or access networks
Objective KPI: KPI assessing one of the objectives of operational energy performance which is subsequently used to
define a Global KPI for energy management
operational infrastructure: combination of ICT equipment together with the power supply and environmental control
systems necessary to ensure provision of service
Operator Site (OS): premises accommodating Network Telecommunications Equipment (NTE) providing direct
connection to the core and access networks and which may also accommodate Information Technology Equipment
(ITE)
NOTE 1: An operator site that is only connected to the core network is considered as a network data centre.
NOTE 2: An operator site of a cable access network may be termed a local head-end.
Radio Access Network (RAN): telecommunications network in which the access to the network (connection between
user equipment and network) is implemented over the air interface
NOTE: Part of GERAN, UTRAN or E-UTRA networks defined by 3GPP.
Repeater (R): device with two RF ports, both of which are intended to be connected to antennas, which is capable of
receiving, amplifying and transmitting simultaneously in one direction a signal in a base station's transmit band and in
the other direction a signal in the corresponding base station's receive band
renewable energy: energy from renewable sources" as energy from renewable non-fossil sources, namely wind, solar,
aerothermal, geothermal, hydrothermal and ocean energy, hydropower, biomass, landfill gas, sewage treatment plant
gas and biogases
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.