ETSI EN 302 574-3 V2.1.1 (2016-06)
Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 3: User Equipment (UE) for narrowband systems
Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 3: User Equipment (UE) for narrowband systems
REN/SES-00397
Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani standard za satelitske zemeljske postaje (MES) za MSS, ki delujejo v frekvenčnih pasovih od 1980 MHz do 2010 MHz (zemlja-vesolje) in od 2170 MHz do 2200 MHz (vesolje-zemlja) - 3. del: Uporabniška oprema (EU) za ozkopasovne sisteme, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument se uporablja za radijsko opremo uporabniške opreme z naslednjimi značilnostmi:
• Uporabniška oprema ima sposobnost oddajanja in sprejemanja ter deluje v geostacionarnem satelitskem omrežju.
• Uporabniška oprema deluje s pasovno širino signala dodeljenega kanala (CBw), ki je manjši od 1 MHz.
• Uporabniška oprema je lahko ročna prenosna oprema, ki je pritrjena ali polpritrjena na vozilo in povezana z gostiteljem, ali je sestavni del v večnačinovnem terminalu. Sestavljena je lahko iz več modulov
s povezanimi priključki in uporabniškim vmesnikom ali je samozadostna enota.
• Če je uporabniška oprema sestavni del večnačinovnega terminala,
zahteve tega dokumenta veljajo samo za uporabniško opremo v terminalu, ki deluje v frekvenčnih pasovih mobilnih satelitskih storitev (MSS), podanih v preglednici 1, razen če je v dokumentu drugače navedeno.
Ta tip radijske opreme lahko deluje v vseh delih frekvenčnih pasov iz preglednice 1.
Ta dokument zajema določbe člena 3.2 Direktive 2014/53/EU [7] (direktive RE), ki navaja: »/.../ Radijska oprema je izdelana tako, da optimalno uporablja in podpira učinkovito izrabo radijskega spektra, z namenom preprečevanja škodljivega motenja.«
Poleg tega dokumenta se za opremo v področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive RE [7].
OPOMBA: seznam tovrstnih evropskih standardov je na voljo na spletnem mestu http://www.newapproach.org.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.YHVROMHSatellite Earth Stations and Systems (SES) - Harmonised Standard for Satellite Earth Stations (MES) for MSS operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands - Part 3: User Equipment (UE) for narrowband systems covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:ETSI EN 302 574-3 V2.1.1 (2016-06)SIST EN 302 574-3 V2.1.1:2016en01-september-2016SIST EN 302 574-3 V2.1.1:2016SLOVENSKI
STANDARD
SIST EN 302 574-3 V2.1.1:2016
ETSI EN 302 574-3 V2.1.1 (2016-06) Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 3: User Equipment (UE) for narrowband systems
HARMONISED EUROPEAN STANDARD SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 2
Reference REN/SES-00397 Keywords MES, mobile, MSS, narrowband, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Modal verbs terminology . 5 Introduction . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 10 3.3 Abbreviations . 10 4 Technical requirements specifications . 11 4.1 Environmental profile . 11 4.2 Conformance requirements . 11 4.2.0 General . 11 4.2.1 Introduction. 11 4.2.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) . 12 4.2.2.1 Justification . 12 4.2.2.2 Technical requirements . 12 4.2.2.3 Conformance test . 14 4.2.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) . 14 4.2.3.1 Justification . 14 4.2.3.2 Technical requirements . 14 4.2.3.3 Conformance test . 16 4.2.4 Unwanted emissions in carrier-off state . 16 4.2.4.1 Justification . 16 4.2.4.2 Technical requirements . 16 4.2.4.3 Conformance test . 17 4.2.5 UE Control and Monitoring Functions (CMF) . 17 4.2.5.1 Absence of a valid network handling of output power . 17 4.2.5.1.1 Definition. 17 4.2.5.1.2 Limit . 17 4.2.5.1.3 Conformance . 17 4.2.5.2 Loss of signal handling of output power . 17 4.2.5.2.1 Definition. 17 4.2.5.2.2 Limit . 18 4.2.5.2.3 Conformance . 18 4.2.6 Receiver Adjacent Channel Selectivity. 18 4.2.6.1 Justification . 18 4.2.6.2 Technical requirements . 18 4.2.6.3 Conformance test . 18 4.2.7 Receiver Blocking Characteristics . 18 4.2.7.1 Justification . 18 4.2.7.2 Technical requirements . 18 4.2.7.3 Conformance test . 19 5 Testing for compliance with technical requirements . 19 5.1 Environmental conditions for testing . 19 5.2 Interpretation of the measurement results . 19 5.3 Essential radio test suites . 20 5.3.1 General . 20 5.3.1.1 Description of equipment . 20 5.3.1.2 Testing of host-connected equipment and plug-in modules . 21 SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 4 5.3.1.2.1 Alternative approaches . 21 5.3.1.2.2 Alternative A: combined equipment . 21 5.3.1.2.3 Alternative B: use of a test jig . 21 5.3.1.3 CMF/Special Test Equipment (STE) . 21 5.3.1.4 General test requirements . 21 5.3.1.4.1 UE test modes . 21 5.3.1.4.2 Special Test Equipment (STE) . 22 5.3.1.4.3 Laboratory Test Equipment (LTE) . 23 5.3.1.4.4 Methods of test for UE RF emissions according to the equipment type . 23 5.3.1.4.5 Procedures for measurement of radiated emissions . 23 5.3.1.4.6 Procedures for measurement of conducted emissions . 28 5.3.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) . 30 5.3.2.1 Method of test . 30 5.3.2.2 Peak measurement . 31 5.3.2.3 Average measurement . 31 5.3.2.4 Test requirements . 31 5.3.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) . 32 5.3.3.1 Method of test . 32 5.3.3.2 Measurement method . 32 5.3.3.3 Test requirements . 33 5.3.4 Unwanted emissions in carrier-off state . 33 5.3.4.1 Method of test . 33 5.3.4.2 Measurement method . 33 5.3.4.3 Test requirements . 33 5.3.5 UE Control and Monitoring Functions (CMF) . 34 5.3.5.1 Method of test . 34 5.3.5.2 Testing of output power in absence of a valid network . 34 5.3.5.2.1 Test procedure . 34 5.3.5.2.2 Measurement method . 34 5.3.5.3 Testing of output power in loss of signal . 34 5.3.5.3.1 Test procedure . 34 5.3.5.3.2 Measurement method . 35 5.3.6 Receiver Adjacent Channel Selectivity. 35 5.3.6.1 General . 35 5.3.6.2 Test set-up . 35 5.3.6.3 Test procedure . 35 5.3.7 Receiver Blocking Characteristics . 36 5.3.7.1 General . 36 5.3.7.2 Test set-up . 36 5.3.7.3 Test procedure . 36 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 37 Annex B (informative): Environmental profile specification . 39 B.1 Introduction . 39 B.2 Temperature . 39 B.3 Voltage . 39 B.4 Test environment . 40 Annex C (informative): Bibliography . 41 History . 42
SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [7]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 3 of a multi-part deliverable covering the Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU, as identified below: Part 1: "Complementary Ground Component (CGC) for wideband systems"; Part 2: "User Equipment (UE) for wideband systems"; Part 3: "User Equipment (UE) for narrowband systems".
National transposition dates Date of adoption of this EN: 30 May 2016 Date of latest announcement of this EN (doa): 31 August 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
28 February 2017 Date of withdrawal of any conflicting National Standard (dow): 28 February 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 6 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [7]. The modular structure is shown in ETSI EG 201 399 [i.5].
SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 7 1 Scope The present document applies to User Equipment (UE) radio equipment type which have the following characteristics: • these UEs have both transmit and receive capabilities and operate in a Geostationary satellite network; • these UEs operate with an assigned channel signal bandwidth (CBw) smaller than 1 MHz; • these UEs may be handset, handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed equipment, or may be an element in a multi-mode terminal. It may consist of a number of modules with associated connections and user interface, or may be a self-contained single unit; • if the UE is an element in a multi-mode terminal, unless otherwise stated in the present document, its requirements apply only to the UE element of the terminal operating in the Mobile Satellite Service (MSS) frequency bands given in table 1. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1. Table 1: Mobile Satellite Service UE frequency bands Operating band Direction of transmission UE frequency bands I UE Transmit (earth-to-space) 1 980 MHz to 2 010 MHz UE Receive (space-to-earth) 2 170 MHz to 2 200 MHz
The present document is intended to cover the provisions of Directive 2014/53/EU [7] (RE Directive) article 3.2 which states that "….radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the RE Directive [7] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Void. [2] Recommendation ITU-T O.153 (10/1992): "Basic parameters for the measurement of error performance at bit rates below the primary rate". [3] CISPR 16-1-4 (2010): "Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements". SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 8 [4] ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [5] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold". [6] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat". [7] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ETSI TR 102 215: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Recommended approach, and possible limits for measurement uncertainty for the measurement of radiated electromagnetic fields above 1 GHz". [i.2] Void. [i.3] Void. [i.4] Void. [i.5] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the Radio & Telecommunication Terminal Equipment Directive 1999/5/EC (R&TTE) and a first guide on the impact of the Radio Equipment Directive 2014/53/EU (RED) on Harmonized Standards". [i.6] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the Directive 2014/53/EU [7] and the following apply: 3 dB Bandwidth (B3dB): total width of the signal spectrum 3 dB below the maximum in-band density applicant: manufacturer or his authorized representative within the European Community or the person responsible for placing the apparatus on the market carrier-on time (initial bursts): period when a UE is transmitting a signal NOTE: For UEs that transmit in a non-continuous mode, the carrier-on time only includes the times when the UE is transmitting a signal. SIST EN 302 574-3 V2.1.1:2016
ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 9 carrier-on state: state in which the UE is transmitting a carrier carrier-off state: state in which the UE is not transmitting a carrier conducted measurement: measurement of emissions from an antenna port of the UE made by direct wired connection to the port environmental profile: range of environmental conditions under which equipment within the scope of the present document is required to comply with the provisions of the present document Equivalent Isotropically Radiated Power (EIRP): product of transmitter power and the antenna gain in the direction considered, relative to an isotropic source radiating uniformly in all directions fellow radio station: one of the (other) modes of a multimode UE handheld: indicates a UE which is self-contained and is small enough and light enough to be carried and used during a call with one hand host-connected: mode in which a UE is connected to a host equipment for its operation host equipment: any equipment which has a complete user functionality when not connected to the UE, and to which the UE provides additional functionality, and to which connection is necessary for the UE to offer functionality in-band signals: signals which are located in the operating band plus an offset of 10 MHz outside this operating band Installable Equipment (IE): equipment which is intended to be installed in a vehicle NOTE: An IE may consist of one or several interconnected modules. The IE is composed of modules intended to be externally mounted as declared by the applicant, and d
...
ETSI EN 302 574-3 V2.1.1 (2016-06)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Mobile Earth Stations (MES)
operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and
2 170 MHz to 2 200 MHz (space-to-earth) frequency bands
covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 3: User Equipment (UE) for narrowband systems
---------------------- Page: 1 ----------------------
2 ETSI EN 302 574-3 V2.1.1 (2016-06)
Reference
REN/SES-00397
Keywords
MES, mobile, MSS, narrowband, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 574-3 V2.1.1 (2016-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.0 General . 11
4.2.1 Introduction. 11
4.2.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) . 12
4.2.2.1 Justification . 12
4.2.2.2 Technical requirements . 12
4.2.2.3 Conformance test . 14
4.2.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) . 14
4.2.3.1 Justification . 14
4.2.3.2 Technical requirements . 14
4.2.3.3 Conformance test . 16
4.2.4 Unwanted emissions in carrier-off state . 16
4.2.4.1 Justification . 16
4.2.4.2 Technical requirements . 16
4.2.4.3 Conformance test . 17
4.2.5 UE Control and Monitoring Functions (CMF) . 17
4.2.5.1 Absence of a valid network handling of output power . 17
4.2.5.1.1 Definition. 17
4.2.5.1.2 Limit . 17
4.2.5.1.3 Conformance . 17
4.2.5.2 Loss of signal handling of output power . 17
4.2.5.2.1 Definition. 17
4.2.5.2.2 Limit . 18
4.2.5.2.3 Conformance . 18
4.2.6 Receiver Adjacent Channel Selectivity. 18
4.2.6.1 Justification . 18
4.2.6.2 Technical requirements . 18
4.2.6.3 Conformance test . 18
4.2.7 Receiver Blocking Characteristics . 18
4.2.7.1 Justification . 18
4.2.7.2 Technical requirements . 18
4.2.7.3 Conformance test . 19
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
5.3 Essential radio test suites . 20
5.3.1 General . 20
5.3.1.1 Description of equipment . 20
5.3.1.2 Testing of host-connected equipment and plug-in modules . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 574-3 V2.1.1 (2016-06)
5.3.1.2.1 Alternative approaches . 21
5.3.1.2.2 Alternative A: combined equipment . 21
5.3.1.2.3 Alternative B: use of a test jig . 21
5.3.1.3 CMF/Special Test Equipment (STE) . 21
5.3.1.4 General test requirements . 21
5.3.1.4.1 UE test modes . 21
5.3.1.4.2 Special Test Equipment (STE) . 22
5.3.1.4.3 Laboratory Test Equipment (LTE) . 23
5.3.1.4.4 Methods of test for UE RF emissions according to the equipment type . 23
5.3.1.4.5 Procedures for measurement of radiated emissions . 23
5.3.1.4.6 Procedures for measurement of conducted emissions . 28
5.3.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) . 30
5.3.2.1 Method of test . 30
5.3.2.2 Peak measurement . 31
5.3.2.3 Average measurement . 31
5.3.2.4 Test requirements . 31
5.3.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) . 32
5.3.3.1 Method of test . 32
5.3.3.2 Measurement method . 32
5.3.3.3 Test requirements . 33
5.3.4 Unwanted emissions in carrier-off state . 33
5.3.4.1 Method of test . 33
5.3.4.2 Measurement method . 33
5.3.4.3 Test requirements . 33
5.3.5 UE Control and Monitoring Functions (CMF) . 34
5.3.5.1 Method of test . 34
5.3.5.2 Testing of output power in absence of a valid network . 34
5.3.5.2.1 Test procedure . 34
5.3.5.2.2 Measurement method . 34
5.3.5.3 Testing of output power in loss of signal . 34
5.3.5.3.1 Test procedure . 34
5.3.5.3.2 Measurement method . 35
5.3.6 Receiver Adjacent Channel Selectivity. 35
5.3.6.1 General . 35
5.3.6.2 Test set-up . 35
5.3.6.3 Test procedure . 35
5.3.7 Receiver Blocking Characteristics . 36
5.3.7.1 General . 36
5.3.7.2 Test set-up . 36
5.3.7.3 Test procedure . 36
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 37
Annex B (informative): Environmental profile specification . 39
B.1 Introduction . 39
B.2 Temperature . 39
B.3 Voltage . 39
B.4 Test environment . 40
Annex C (informative): Bibliography . 41
History . 42
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 574-3 V2.1.1 (2016-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations
and Systems (SES).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [7].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 3 of a multi-part deliverable covering the Harmonised Standard for Mobile Earth Stations
(MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth)
frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU, as identified below:
Part 1: "Complementary Ground Component (CGC) for wideband systems";
Part 2: "User Equipment (UE) for wideband systems";
Part 3: "User Equipment (UE) for narrowband systems".
National transposition dates
Date of adoption of this EN: 30 May 2016
Date of latest announcement of this EN (doa): 31 August 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2017
Date of withdrawal of any conflicting National Standard (dow): 28 February 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 574-3 V2.1.1 (2016-06)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [7]. The
modular structure is shown in ETSI EG 201 399 [i.5].
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 574-3 V2.1.1 (2016-06)
1 Scope
The present document applies to User Equipment (UE) radio equipment type which have the following characteristics:
• these UEs have both transmit and receive capabilities and operate in a Geostationary satellite network;
• these UEs operate with an assigned channel signal bandwidth (CBw) smaller than 1 MHz;
• these UEs may be handset, handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed
equipment, or may be an element in a multi-mode terminal. It may consist of a number of modules with
associated connections and user interface, or may be a self-contained single unit;
• if the UE is an element in a multi-mode terminal, unless otherwise stated in the present document, its
requirements apply only to the UE element of the terminal operating in the Mobile Satellite Service (MSS)
frequency bands given in table 1.
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Mobile Satellite Service UE frequency bands
Operating band Direction of transmission UE frequency bands
UE Transmit (earth-to-space) 1 980 MHz to 2 010 MHz
I
UE Receive (space-to-earth) 2 170 MHz to 2 200 MHz
The present document is intended to cover the provisions of Directive 2014/53/EU [7] (RE Directive) article 3.2 which
states that "….radio equipment shall be so constructed that it both effectively uses and supports the efficient use of
radio spectrum in order to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the RE Directive [7] may apply to equipment within the scope of the present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] Recommendation ITU-T O.153 (10/1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[3] CISPR 16-1-4 (2010): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites
for radiated disturbance measurements".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 574-3 V2.1.1 (2016-06)
[4] ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
[5] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[6] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[7] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 102 215: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.2] Void.
[i.3] Void.
[i.4] Void.
[i.5] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the Radio & Telecommunication
Terminal Equipment Directive 1999/5/EC (R&TTE) and a first guide on the impact of the Radio
Equipment Directive 2014/53/EU (RED) on Harmonized Standards".
[i.6] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the Directive 2014/53/EU [7] and the
following apply:
3 dB Bandwidth (B3dB): total width of the signal spectrum 3 dB below the maximum in-band density
applicant: manufacturer or his authorized representative within the European Community or the person responsible for
placing the apparatus on the market
carrier-on time (initial bursts): period when a UE is transmitting a signal
NOTE: For UEs that transmit in a non-continuous mode, the carrier-on time only includes the times when the UE
is transmitting a signal.
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 302 574-3 V2.1.1 (2016-06)
carrier-on state: state in which the UE is transmitting a carrier
carrier-off state: state in which the UE is not transmitting a carrier
conducted measurement: measurement of emissions from an antenna port of the UE made by direct wired connection
to the port
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
Equivalent Isotropically Radiated Power (EIRP): product of transmitter power and the antenna gain in the direction
considered, relative to an isotropic source radiating uniformly in all directions
fellow radio station: one of the (other) modes of a multimode UE
handheld: indicates a UE which is self-contained and is small enough and light enough to be carried and used during a
call with one hand
host-connected: mode in which a UE is connected to a host equipment for its operation
host equipment: any equipment which has a complete user functionality when not connected to the UE, and to which
the UE provides additional functionality, and to which connection is necessary for the UE to offer functionality
in-band signals: signals which are located in the operating band plus an offset of 10 MHz outside this operating band
Installable Equipment (IE): equipment which is intended to be installed in a vehicle
NOTE: An IE may consist of one or several interconnected modules. The IE is composed of modules intended to
be externally mounted as declared by the applicant, and defined as Externally Mounted Equipment (EME)
and the remaining modules(s) as Internally Mounted Equipment (IME).
Laboratory Test Equipment (LTE): logical grouping that contains the standard test equipment provided by a test
laboratory
MSS band: continuous r
...
Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Satellite Earth Stations (MES) for
MSS operating in the 1 980 MHz to
2 010 MHz (earth-to-space) and 2 170 MHz to
2 200 MHz (space-to-earth) frequency bands;
Part 3: User Equipment (UE) for narrowband systems
covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
Reference
REN/SES-00397
Keywords
MES, mobile, MSS, narrowband, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.0 General . 11
4.2.1 Introduction. 11
4.2.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) . 11
4.2.2.1 Justification . 11
4.2.2.2 Technical requirements . 12
4.2.2.3 Conformance test . 14
4.2.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) . 14
4.2.3.1 Justification . 14
4.2.3.2 Technical requirements . 14
4.2.3.3 Conformance test . 16
4.2.4 Unwanted emissions in carrier-off state . 16
4.2.4.1 Justification . 16
4.2.4.2 Technical requirements . 16
4.2.4.3 Conformance test . 17
4.2.5 UE Control and Monitoring Functions (CMF) . 17
4.2.5.1 Absence of a valid network handling of output power . 17
4.2.5.1.1 Definition. 17
4.2.5.1.2 Limit . 17
4.2.5.1.3 Conformance . 17
4.2.5.2 Loss of signal handling of output power . 17
4.2.5.2.1 Definition. 17
4.2.5.2.2 Limit . 17
4.2.5.2.3 Conformance . 18
4.2.6 Receiver Adjacent Channel Selectivity. 18
4.2.6.1 Justification . 18
4.2.6.2 Technical requirements . 18
4.2.6.3 Conformance test . 18
4.2.7 Receiver Blocking Characteristics . 18
4.2.7.1 Justification . 18
4.2.7.2 Technical requirements . 18
4.2.7.3 Conformance test . 19
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
5.3 Essential radio test suites . 20
5.3.1 General . 20
5.3.1.1 Description of equipment . 20
5.3.1.2 Testing of host-connected equipment and plug-in modules . 21
5.3.1.2.1 Alternative approaches . 21
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
5.3.1.2.2 Alternative A: combined equipment . 21
5.3.1.2.3 Alternative B: use of a test jig . 21
5.3.1.3 CMF/Special Test Equipment (STE) . 21
5.3.1.4 General test requirements . 21
5.3.1.4.1 UE test modes . 21
5.3.1.4.2 Special Test Equipment (STE) . 22
5.3.1.4.3 Laboratory Test Equipment (LTE) . 22
5.3.1.4.4 Methods of test for UE RF emissions according to the equipment type . 23
5.3.1.4.5 Procedures for measurement of radiated emissions . 23
5.3.1.4.6 Procedures for measurement of conducted emissions . 27
5.3.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) . 29
5.3.2.1 Method of test . 29
5.3.2.2 Peak measurement . 29
5.3.2.3 Average measurement . 30
5.3.2.4 Test requirements . 30
5.3.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) . 30
5.3.3.1 Method of test . 30
5.3.3.2 Measurement method . 31
5.3.3.3 Test requirements . 31
5.3.4 Unwanted emissions in carrier-off state . 31
5.3.4.1 Method of test . 31
5.3.4.2 Measurement method . 32
5.3.4.3 Test requirements . 32
5.3.5 UE Control and Monitoring Functions (CMF) . 32
5.3.5.1 Method of test . 32
5.3.5.2 Testing of output power in absence of a valid network . 32
5.3.5.2.1 Test procedure . 32
5.3.5.2.2 Measurement method . 33
5.3.5.3 Testing of output power in loss of signal . 33
5.3.5.3.1 Test procedure . 33
5.3.5.3.2 Measurement method . 33
5.3.6 Receiver Adjacent Channel Selectivity. 33
5.3.6.1 General . 33
5.3.6.2 Test set-up . 33
5.3.6.3 Test procedure . 34
5.3.7 Receiver Blocking Characteristics . 34
5.3.7.1 General . 34
5.3.7.2 Test set-up . 34
5.3.7.3 Test procedure . 34
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 36
Annex B (informative): Environmental profile specification . 38
B.1 Introduction . 38
B.2 Temperature . 38
B.3 Voltage . 38
B.4 Test environment . 39
Annex C (informative): Bibliography . 40
History . 41
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth
Stations and Systems (SES), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [7].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 3 of a multi-part deliverable covering the Harmonised Standard for satellite earth stations
for MSS operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth)
frequency bands, as identified below:
Part 1: "Complementary Ground Component (CGC) for wideband systems covering the essential requirements of
article 3.2 of the Directive 2014/53/EU";
Part 2: "User Equipment (UE) for wideband systems covering the essential requirements of article 3.2 of the
Directive 2014/53/EU";
Part 3: "User Equipment (UE) for narrowband systems covering the essential requirements of article 3.2 of
the Directive 2014/53/EU".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [7]. The
modular structure is shown in ETSI EG 201 399 [i.5].
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
1 Scope
The present document applies to User Equipment (UE) radio equipment type which have the following characteristics:
• these UEs have both transmit and receive capabilities and operate in a Geostationary satellite network;
• these UEs operate with an assigned channel signal bandwidth (CBw) smaller than 1 MHz;
• these UEs may be handset, handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed
equipment, or may be an element in a multi-mode terminal. It may consist of a number of modules with
associated connections and user interface, or may be a self-contained single unit;
• if the UE is an element in a multi-mode terminal, unless otherwise stated in the present document, its
requirements apply only to the UE element of the terminal operating in the Mobile Satellite Service (MSS)
frequency bands given in table 1.
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Mobile Satellite Service UE frequency bands
Operating band Direction of transmission UE frequency bands
UE Transmit (earth-to-space) 1 980 MHz to 2 010 MHz
I
UE Receive (space-to-earth) 2 170 MHz to 2 200 MHz
The present document is intended to cover the provisions of Directive 2014/53/EU [7] (RE Directive) article 3.2 which
states that "….radio equipment shall be so constructed that it both effectively uses and supports the efficient use of
radio spectrum in order to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the RE Directive [7] may apply to equipment within the scope of the present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] Recommendation ITU-T O.153 (10/1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[3] CISPR 16-1-4 (2010): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites
for radiated disturbance measurements".
[4] ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
[5] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[6] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[7] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 102 215: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.2] Void.
[i.3] Void.
[i.4] Void.
[i.5] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the Radio & Telecommunication
Terminal Equipment Directive 1999/5/EC (R&TTE) and a first guide on the impact of the Radio
Equipment Directive 2014/53/EU (RED) on Harmonized Standards".
[i.6] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the Directive 2014/53/EU [7] and the
following apply:
3 dB Bandwidth (B3dB): total width of the signal spectrum 3 dB below the maximum in-band density
applicant: manufacturer or his authorized representative within the European Community or the person responsible for
placing the apparatus on the market
carrier-on time (initial bursts): period when a UE is transmitting a signal
NOTE: For UEs that transmit in a non-continuous mode, the carrier-on time only includes the times when the UE
is transmitting a signal.
carrier-on state: state in which the UE is transmitting a carrier
carrier-off state: state in which the UE is not transmitting a carrier
conducted measurement: measurement of emissions from an antenna port of the UE made by direct wired connection
to the port
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 302 574-3 V2.1.0 (2016-03)
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
Equivalent Isotropically Radiated Power (EIRP): product of transmitter power and the antenna gain in the direction
considered, relative to an isotropic source radiating uniformly in all directions
fellow radio station: one of the (other) modes of a multimode UE
handheld: indicates a UE which is self-contained and is small enough and light enough to be carried and used during a
call with one hand
host-connected: mode in which a UE is connected to a host equipment for its operation
host equipment: any equipment which has a complete user functionality when not connected to the UE, and to which
the UE provides additional functionality, and to which connection is necessary for the UE to offer functionality
in-band signals: signals which are located in the operating band plus an offset of 10 MHz outside this operating band
Installable Equipment (IE): equipment which is intended to be installed in a vehicle
NOTE: An IE may consist of one or several interconnected modules. The IE is composed of module
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.