Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating devices employing AIS; Part 1: Technical characteristics and methods of measurement

DEN/ERM-TG26-100-1

Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Pomorski osebni javljalniki lokacije majhne moči z uporabo AIS - 1. del: Tehnične karakteristike in merilne metode

Ta dokument določa najmanjše zahteve za pomorske osebne javljalnike lokacije majhne moči z uporabo AIS in integrirani sprejemnik GNSS za zagotavljanje funkcije javljanja lokacije. Ta dokument zajema ustrezne določbe Pravilnika o radiokomunikacijah [i.3] Mednarodne zveze za telekomunikacije (ITU), vključene v Priporočilo ITU-R M.1371-5 [1]. Pri takšni uporabi sta oddajna moč in časovno obdobje delovanja zmanjšana, da se omogoči uporaba ustrezno majhne opreme, ki jo je mogoče udobno nositi, ter da se razpon delovanja omeji na lokalno območje.

General Information

Status
Published
Publication Date
14-Sep-2014
Current Stage
12 - Completion
Due Date
15-Sep-2014
Completion Date
15-Sep-2014

Buy Standard

Standard
EN 303 098-1 V1.2.1:2014
English language
52 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 303 098-1 V1.2.1 (2014-09) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating devices employing AIS; Part 1: Technical characteristics and methods of measurement
English language
52 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 098-1 V1.2.1 (2014-07) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating devices employing AIS; Part 1: Technical characteristics and methods of measurement
English language
52 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 098-1 V1.1.1 (2014-02) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating devices employing AIS; Part 1: Technical characteristics and methods of measurement
English language
53 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 098-1 V1.1.0 (2013-05) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating beacons employing AIS Part 1: Technical characteristics and methods of measurement
English language
50 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Maritime low power personal locating beacons employing AIS - Part 1: Technical characteristics and methods of measurement47.020.70Navigacijska in krmilna opremaNavigation and control equipment33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.01Radijske komunikacije na splošnoRadiocommunications in generalICS:Ta slovenski standard je istoveten z:EN 303 098-1 Version 1.2.1SIST EN 303 098-1 V1.2.1:2014en01-november-2014SIST EN 303 098-1 V1.2.1:2014SLOVENSKI
STANDARD



SIST EN 303 098-1 V1.2.1:2014



ETSI EN 303 098-1 V1.2.1 (2014-09) Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating devices employing AIS; Part 1: Technical characteristics and methods of measurement
EUROPEAN STANDARD SIST EN 303 098-1 V1.2.1:2014



ETSI ETSI EN 303 098-1 V1.2.1 (2014-09) 2
Reference DEN/ERM-TG26-100-1 Keywords maritime, radio, SAR, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 098-1 V1.2.1:2014



ETSI ETSI EN 303 098-1 V1.2.1 (2014-09) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 9 3.3 Abbreviations . 9 4 General requirements . 10 4.1 Construction . 10 4.1.1 Categories of equipment . 11 4.2 Controls . 11 4.3 Indicators . 11 4.4 Identifier (user ID). 11 4.5 Labelling. 12 4.5.1 Labelling Requirements . 12 4.6 Instructions . 12 4.7 Power source . 12 4.7.1 Battery requirements . 12 4.7.2 Battery capacity . 13 4.7.3 Safety precautions . 13 5 Technical requirements . 13 5.1 General . 13 5.2 AIS transmission characteristics . 13 5.2.1 AIS messages . 13 5.2.1.1 Active mode . 14 5.2.1.2 Test mode . 14 5.2.2 Synchronization . 14 5.2.2.1 Active mode . 14 5.2.2.2 Test mode . 14 5.2.3 GNSS position source . 14 5.2.3.1 UTC. 15 5.2.3.2 UTC parameters storage . 15 5.2.4 Required settings . 15 5.2.5 Minimum transmitter performance characteristics . 16 5.2.6 VHF Data Link (VDL) Access . 16 5.2.6.1 Active mode . 16 5.2.6.2 Test mode . 17 6 General conditions of measurement . 17 6.1 Conformity testing . 17 6.2 Test Frequencies . 17 6.3 Identifier (user ID). 17 6.4 Artificial Antenna . 17 6.5 Test signals . 18 6.5.1 Standard test signal number 1 . 18 6.5.2 Standard test signal number 2 . 18 6.5.3 Standard test signal number 3 . 18 6.5.4 Reference timing signal . 18 6.6 Measurement uncertainty and interpretation of the measured results . 18 SIST EN 303 098-1 V1.2.1:2014



ETSI ETSI EN 303 098-1 V1.2.1 (2014-09) 4 6.6.1 Measurement uncertainty . 18 6.6.2 Interpretation of the measurement results . 19 6.7 Test conditions power sources and ambient temperatures . 19 6.7.1 Normal and extreme test conditions. 19 6.7.2 Test power source . 19 6.8 Normal test conditions . 19 6.8.1 Normal temperature and humidity . 19 6.8.2 Normal test voltage . 19 6.9 Extreme test conditions . 19 6.9.1 Extreme temperatures . 19 6.9.1.1 Procedure for tests at extreme temperatures . 20 6.9.2 Extreme test voltages . 20 6.9.2.1 Upper extreme test voltage . 20 6.9.2.2 Lower extreme test voltage . 20 7 Environmental tests . 20 7.1 Introduction . 20 7.2 Procedure . 20 7.3 Performance check . 20 7.4 Drop test . 20 7.4.1 Definition . 20 7.4.2 Test conditions . 21 7.4.3 Method of measurement . 21 7.4.4 Requirements . 21 7.5 Temperature tests . 21 7.5.1 Definition . 21 7.5.2 Dry heat test . 21 7.5.2.1 Method of measurement . 21 7.5.2.2 Requirements . 22 7.5.3 Damp heat test . 22 7.5.3.1 Method of measurement . 22 7.5.3.2 Requirements . 22 7.5.4 Low temperature test . 22 7.5.4.1 Method of measurement . 22 7.5.4.2 Requirements . 22 7.5.5 Low temperature battery endurance test . 23 7.5.5.1 Method of measurement . 23 7.5.5.2 Requirements . 23 7.6 Vibration test . 23 7.6.1 Definition . 23 7.6.2 Method of measurement . 23 7.6.3 Requirement . 24 7.7 Corrosion test . 24 7.7.1 Definition . 24 7.7.2 Method of measurement . 24 7.7.3 Requirements . 24 7.8 Thermal shock test. 25 7.8.1 Definition . 25 7.8.2 Method of measurement . 25 7.8.3 Requirements . 25 7.9 Buoyancy test . 25 7.9.1 Definition . 25 7.9.2 Method of measurement . 25 7.9.3 Requirements . 25 7.10 Compass safe distance test . 26 7.10.1 Definition . 26 7.10.2 Method of measurement . 26 7.10.3 Requirements . 26 7.11 Solar radiation test . 27 7.11.1 Definition . 27 7.11.2 Method of measurement . 27 7.11.3 Requirements . 27 SIST EN 303 098-1 V1.2.1:2014



ETSI ETSI EN 303 098-1 V1.2.1 (2014-09) 5 7.12 Oil resistance test. 27 7.12.1 Definition . 27 7.12.2 Method of measurement . 27 7.12.3 Requirements . 28 7.13 Protection of the transmitter . 28 7.13.1 Definition . 28 7.13.2 Method of measurement . 28 7.13.3 Requirement . 28 8 Tests on the AIS transmitter . 28 8.1 Frequency error . 28 8.1.1 Definition . 28 8.1.2 Method of measurement . 28 8.1.3 Limit . 29 8.2 Conducted Power . 29 8.2.1 Definition . 29 8.2.2 Method of measurement under normal test conditions . 29 8.2.3 Limit . 29 8.3 Maximum Effective Radiated Power (ERP). 29 8.3.1 Definition . 29 8.3.2 Method of measurement . 29 8.3.3 Limits . 30 8.4 Transmitter spectrum mask . 30 8.4.1 Definition . 30 8.4.2 Method of measurement . 30 8.4.3 Limit . 31 8.5 Transmitter transient behaviour (output power) . 31 8.5.1 Definition . 31 8.5.2 Method of measurement . 32 8.5.3 Limit . 33 8.6 Transmitter Transient Behaviour (frequency deviation) . 33 8.6.1 Definition . 33 8.6.2 Method of measurement . 33 8.6.3 Limit . 34 8.7 Synchronization accuracy . 34 8.7.1 Definition . 34 8.7.2 Method of measurement . 34 8.7.3 Limit . 35 8.8 Spurious emissions . 36 8.8.1 Definition . 36 8.8.2 Method of measurement . 36 8.8.3 Limit . 36 9 VDL Link layer tests . 36 9.1 Active mode tests . 36 9.1.1 Method of measurement . 36 9.1.2 Initialization period - Required results. 37 9.1.3 Message content of Message 1 - Required results . 37 9.1.4 Message content of Message 14 - Required results . 37 9.1.5 Transmission schedule for Message 1 - Required results . 37 9.1.6 Communication state of Message 1 - Required results . 38 9.1.7 Transmission schedule of Message 14 - Required results. 38 9.1.8 Transmission with lost GNSS - Required results . 38 9.2 Test mode tests with GNSS data available . 39 9.2.1 Method of measurement .
...

ETSI EN 303 098-1 V1.2.1 (2014-09)






EUROPEAN STANDARD
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Maritime low power personal locating devices employing AIS;
Part 1: Technical characteristics and methods of measurement

---------------------- Page: 1 ----------------------
2 ETSI EN 303 098-1 V1.2.1 (2014-09)



Reference
DEN/ERM-TG26-100-1
Keywords
maritime, radio, SAR, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 098-1 V1.2.1 (2014-09)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General requirements . 10
4.1 Construction . 10
4.1.1 Categories of equipment . 11
4.2 Controls . 11
4.3 Indicators . 11
4.4 Identifier (user ID). 11
4.5 Labelling. 12
4.5.1 Labelling Requirements . 12
4.6 Instructions . 12
4.7 Power source . 12
4.7.1 Battery requirements . 12
4.7.2 Battery capacity . 13
4.7.3 Safety precautions . 13
5 Technical requirements . 13
5.1 General . 13
5.2 AIS transmission characteristics . 13
5.2.1 AIS messages . 13
5.2.1.1 Active mode . 14
5.2.1.2 Test mode . 14
5.2.2 Synchronization . 14
5.2.2.1 Active mode . 14
5.2.2.2 Test mode . 14
5.2.3 GNSS position source . 14
5.2.3.1 UTC. 15
5.2.3.2 UTC parameters storage . 15
5.2.4 Required settings . 15
5.2.5 Minimum transmitter performance characteristics . 16
5.2.6 VHF Data Link (VDL) Access . 16
5.2.6.1 Active mode . 16
5.2.6.2 Test mode . 17
6 General conditions of measurement . 17
6.1 Conformity testing . 17
6.2 Test Frequencies . 17
6.3 Identifier (user ID). 17
6.4 Artificial Antenna . 17
6.5 Test signals . 18
6.5.1 Standard test signal number 1 . 18
6.5.2 Standard test signal number 2 . 18
6.5.3 Standard test signal number 3 . 18
6.5.4 Reference timing signal . 18
6.6 Measurement uncertainty and interpretation of the measured results . 18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 098-1 V1.2.1 (2014-09)
6.6.1 Measurement uncertainty . 18
6.6.2 Interpretation of the measurement results . 19
6.7 Test conditions power sources and ambient te mperature s . 19
6.7.1 Normal and extreme test conditions. 19
6.7.2 Test power source . 19
6.8 Normal test conditions . 19
6.8.1 Normal temperature and humidity . 19
6.8.2 Normal test voltage . 19
6.9 Extreme test conditions . 19
6.9.1 Extreme temperatures . 19
6.9.1.1 Procedure for tests at extreme temperatures . 20
6.9.2 Extreme test voltages . 20
6.9.2.1 Upper extreme test voltage . 20
6.9.2.2 Lower extreme test voltage . 20
7 Environmental tests . 20
7.1 Introduction . 20
7.2 Procedure . 20
7.3 Performance check . 20
7.4 Drop test . 20
7.4.1 Definition . 20
7.4.2 Test conditions . 21
7.4.3 Method of measurement . 21
7.4.4 Requirements . 21
7.5 Temperature tests . 21
7.5.1 Definition . 21
7.5.2 Dry heat test . 21
7.5.2.1 Method of measurement . 21
7.5.2.2 Requirements . 22
7.5.3 Damp heat test . 22
7.5.3.1 Method of measurement . 22
7.5.3.2 Requirements . 22
7.5.4 Low temperature test . 22
7.5.4.1 Method of measurement . 22
7.5.4.2 Requirements . 22
7.5.5 Low temperature battery endurance test . 23
7.5.5.1 Method of measurement . 23
7.5.5.2 Requirements . 23
7.6 Vibration test . 23
7.6.1 Definition . 23
7.6.2 Method of measurement . 23
7.6.3 Requirement . 24
7.7 Corrosion test . 24
7.7.1 Definition . 24
7.7.2 Method of measurement . 24
7.7.3 Requirements . 24
7.8 Thermal shock test. 25
7.8.1 Definition . 25
7.8.2 Method of measurement . 25
7.8.3 Requirements . 25
7.9 Buoyancy test . 25
7.9.1 Definition . 25
7.9.2 Method of measurement . 25
7.9.3 Requirements . 25
7.10 Compass safe distance test . 26
7.10.1 Definition . 26
7.10.2 Method of measurement . 26
7.10.3 Requirements . 26
7.11 Solar radiation test . 27
7.11.1 Definition . 27
7.11.2 Method of measurement . 27
7.11.3 Requirements . 27
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 098-1 V1.2.1 (2014-09)
7.12 Oil resistance test. 27
7.12.1 Definition . 27
7.12.2 Method of measurement . 27
7.12.3 Requirements . 28
7.13 Protection of the transmitter . 28
7.13.1 Definition . 28
7.13.2 Method of measurement . 28
7.13.3 Requirement . 28
8 Tests on the AIS transmitter . 28
8.1 Frequency error . 28
8.1.1 Definition . 28
8.1.2 Method of measurement . 28
8.1.3 Limit . 29
8.2 Conducted Power . 29
8.2.1 Definition . 29
8.2.2 Method of measurement under normal test conditions . 29
8.2.3 Limit . 29
8.3 Maximum Effective Radiated Power (ERP). 29
8.3.1 Definition . 29
8.3.2 Method of measurement . 29
8.3.3 Limits . 30
8.4 Transmitter spectrum mask . 30
8.4.1 Definition . 30
8.4.2 Method of measurement . 30
8.4.3 Limit . 31
8.5 Transmitter transient behaviour (output power) . 31
8.5.1 Definition . 31
8.5.2 Method of measurement . 32
8.5.3 Limit . 33
8.6 Transmitter Transient Behaviour (frequency deviation) . 33
8.6.1 Definition . 33
8.6.2 Method of measurement . 33
8.6.3 Limit . 34
8.7 Synchronization accuracy . 34
8.7.1 Definition . 34
8.7.2 Method of measurement . 34
8.7.3 Limit . 35
8.8 Spurious emissions . 36
8.8.1 Definition . 36
8.8.2 Method of measurement . 36
8.8.3 Limit . 36
9 VDL Link layer tests . 36
9.1 Active mode tests . 36
9.1.1 Method of measurement . 36
9.1.2 Initialization period - Required results. 37
9.1.3 Message content of Message 1 - Required results . 37
9.1.4 Message content of Message 14 - Required results . 37
9.1.5 Transmission schedule for Message 1 - Required results . 37
9.1.6 Communication state of Message 1 - Required results . 38
9.1.7 Transmission schedule of Message 14 - Required results. 38
9.1.8 Transmission with lost GNSS - Required results . 38
9.2 Test mode tests with GNSS data available . 39
9.2.1 Method of measurement . 39
9.2.2 Required results . 39
9.3 Test mode tests without GNSS data available .
...

Final draft ETSI EN 303 098-1 V1.2.1 (2014-06)






EUROPEAN STANDARD
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Maritime low power personal locating devices employing AIS;
Part 1: Technical characteristics and methods of measurement

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 098-1 V1.2.1 (2014-06)



Reference
DEN/ERM-TG26-100-1
Keywords
maritime, radio, SAR, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 098-1 V1.2.1 (2014-06)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General requirements . 10
4.1 Construction . 10
4.1.1 Categories of equipment . 11
4.2 Controls . 11
4.3 Indicators . 11
4.4 Identifier (user ID). 11
4.5 Labelling. 12
4.5.1 Labelling Requirements . 12
4.6 Instructions . 12
4.7 Power source . 12
4.7.1 Battery requirements . 12
4.7.2 Battery capacity . 13
4.7.3 Safety precautions . 13
5 Technical requirements . 13
5.1 General . 13
5.2 AIS transmission characteristics . 13
5.2.1 AIS messages . 13
5.2.1.1 Active mode . 14
5.2.1.2 Test mode . 14
5.2.2 Synchronization . 14
5.2.2.1 Active mode . 14
5.2.2.2 Test mode . 14
5.2.3 GNSS position source . 14
5.2.3.1 UTC. 15
5.2.3.2 UTC parameters storage . 15
5.2.4 Required settings . 15
5.2.5 Minimum transmitter performance characteristics . 16
5.2.6 VHF Data Link (VDL) Access . 16
5.2.6.1 Active mode . 16
5.2.6.2 Test mode . 17
6 General conditions of measurement . 17
6.1 Conformity testing . 17
6.2 Test Frequencies . 17
6.3 Identifier (user ID). 17
6.4 Artificial Antenna . 17
6.5 Test signals . 18
6.5.1 Standard test signal number 1 . 18
6.5.2 Standard test signal number 2 . 18
6.5.3 Standard test signal number 3 . 18
6.5.4 Reference timing signal . 18
6.6 Measurement uncertainty and interpretation of the measured results . 18
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 098-1 V1.2.1 (2014-06)
6.6.1 Measurement uncertainty . 18
6.6.2 Interpretation of the measurement results . 19
6.7 Test conditions power sources and ambient te mperature s . 19
6.7.1 Normal and extreme test conditions. 19
6.7.2 Test power source . 19
6.8 Normal test conditions . 19
6.8.1 Normal temperature and humidity . 19
6.8.2 Normal test voltage . 19
6.9 Extreme test conditions . 19
6.9.1 Extreme temperatures . 19
6.9.1.1 Procedure for tests at extreme temperatures . 20
6.9.2 Extreme test voltages . 20
6.9.2.1 Upper extreme test voltage . 20
6.9.2.2 Lower extreme test voltage . 20
7 Environmental tests . 20
7.1 Introduction . 20
7.2 Procedure . 20
7.3 Performance check . 20
7.4 Drop test . 20
7.4.1 Definition . 20
7.4.2 Test conditions . 21
7.4.3 Method of measurement . 21
7.4.4 Requirements . 21
7.5 Temperature tests . 21
7.5.1 Definition . 21
7.5.2 Dry heat test . 21
7.5.2.1 Method of measurement . 21
7.5.2.2 Requirements . 22
7.5.3 Damp heat test . 22
7.5.3.1 Method of measurement . 22
7.5.3.2 Requirements . 22
7.5.4 Low temperature test . 22
7.5.4.1 Method of measurement . 22
7.5.4.2 Requirements . 22
7.5.5 Low temperature battery endurance test . 23
7.5.5.1 Method of measurement . 23
7.5.5.2 Requirements . 23
7.6 Vibration test . 23
7.6.1 Definition . 23
7.6.2 Method of measurement . 23
7.6.3 Requirement . 24
7.7 Corrosion test . 24
7.7.1 Definition . 24
7.7.2 Method of measurement . 24
7.7.3 Requirements . 24
7.8 Thermal shock test. 25
7.8.1 Definition . 25
7.8.2 Method of measurement . 25
7.8.3 Requirements . 25
7.9 Buoyancy test . 25
7.9.1 Definition . 25
7.9.2 Method of measurement . 25
7.9.3 Requirements . 25
7.10 Compass safe distance test . 26
7.10.1 Definition . 26
7.10.2 Method of measurement . 26
7.10.3 Requirements . 26
7.11 Solar radiation test . 27
7.11.1 Definition . 27
7.11.2 Method of measurement . 27
7.11.3 Requirements . 27
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 098-1 V1.2.1 (2014-06)
7.12 Oil resistance test. 27
7.12.1 Definition . 27
7.12.2 Method of measurement . 27
7.12.3 Requirements . 28
7.13 Protection of the transmitter . 28
7.13.1 Definition . 28
7.13.2 Method of measurement . 28
7.13.3 Requirement . 28
8 Tests on the AIS transmitter . 28
8.1 Frequency error . 28
8.1.1 Definition . 28
8.1.2 Method of measurement . 28
8.1.3 Limit . 29
8.2 Conducted Power . 29
8.2.1 Definition . 29
8.2.2 Method of measurement under normal test conditions . 29
8.2.3 Limit . 29
8.3 Maximum Effective Radiated Power (ERP). 29
8.3.1 Definition . 29
8.3.2 Method of measurement . 29
8.3.3 Limits . 30
8.4 Transmitter spectrum mask . 30
8.4.1 Definition . 30
8.4.2 Method of measurement . 30
8.4.3 Limit . 31
8.5 Transmitter transient behaviour (output power) . 31
8.5.1 Definition . 31
8.5.2 Method of measurement . 32
8.5.3 Limit . 33
8.6 Transmitter Transient Behaviour (frequency deviation) . 33
8.6.1 Definition . 33
8.6.2 Method of measurement . 33
8.6.3 Limit . 34
8.7 Synchronization accuracy . 34
8.7.1 Definition . 34
8.7.2 Method of measurement . 34
8.7.3 Limit . 35
8.8 Spurious emissions . 36
8.8.1 Definition . 36
8.8.2 Method of measurement . 36
8.8.3 Limit . 36
9 VDL Link layer tests . 36
9.1 Active mode tests . 36
9.1.1 Method of measurement . 36
9.1.2 Initialization period - Required results. 37
9.1.3 Message content of Message 1 - Required results . 37
9.1.4 Message content of Message 14 - Required results . 37
9.1.5 Transmission schedule for Message 1 - Required results . 37
9.1.6 Communication state of Message 1 - Required results . 38
9.1.7 Transmission schedule of Message 14 - Required results. 38
9.1.8 Transmission with lost GNSS - Required results . 38
9.2 Test mode tests with GNSS data available . 39
9.2.1 Method of measurement . 39
9.2.2 Required results . 39
9.3 Test mode tests without GNS
...

Final draft ETSI EN 303 098-1 V1.1.1 (2014-02)






European Standard
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Maritime low power personal locating devices employing AIS;
Part 1: Technical characteristics and methods of measurement

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 098-1 V1.1.1 (2014-02)



Reference
DEN/ERM-TG26-100-1
Keywords
maritime, radio, SAR, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 098-1 V1.1.1 (2014-02)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General requirements . 10
4.1 Construction . 10
4.1.1 Requirements for operational locating devices . 11
4.1.2 Requirements for locating devices solely for training purposes . 11
4.1.3 Categories of equipment . 11
4.2 Controls . 11
4.3 Indicators . 11
4.4 Identifier (user ID). 12
4.5 Labelling. 12
4.5.1 Common Labelling Requirements . 12
4.5.2 Labelling Requirements for operational locating devices . 12
4.5.3 Labelling Requirements for training locating devices . 12
4.6 Instructions . 12
4.7 Power source . 13
4.7.1 Battery requirements . 13
4.7.2 Battery capacity . 13
4.7.3 Safety precautions . 13
5 Technical requirements . 13
5.1 General . 13
5.2 AIS transmission characteristics . 14
5.2.1 AIS messages . 14
5.2.1.1 Active mode . 14
5.2.1.2 Training mode . 14
5.2.1.3 Test mode . 14
5.2.2 Synchronization . 14
5.2.2.1 Active and Training modes . 15
5.2.2.2 Test mode . 15
5.2.3 GNSS position source . 15
5.2.3.1 UTC. 15
5.2.3.2 UTC parameters storage . 16
5.2.4 Required settings . 16
5.2.5 Minimum transmitter performance characteristics . 16
5.2.6 VHF Data Link (VDL) Access . 17
5.2.6.1 Active and Training modes . 17
5.2.6.2 Test mode . 18
5.3 Locating device power source . 18
5.3.1 Battery requirements . 18
6 General conditions of measurement . 18
6.1 Conformity testing . 18
6.2 Test Frequencies . 18
6.3 Identifier (user ID). 18
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 098-1 V1.1.1 (2014-02)
6.4 Artificial Antenna . 18
6.5 Test signals . 18
6.5.1 Standard test signal number 1 . 19
6.5.2 Standard test signal number 2 . 19
6.5.3 Standard test signal number 3 . 19
6.5.4 Reference timing signal . 19
6.6 Measurement uncertainty and interpretation of the measured results . 19
6.6.1 Measurement uncertainty . 19
6.6.2 Interpretation of the measurement results . 19
6.7 Test conditions power sources and ambient te mperature s . 20
6.7.1 Normal and extreme test conditions. 20
6.7.2 Test power source . 20
6.8 Normal test conditions . 20
6.8.1 Normal temperature and humidity . 20
6.8.2 Normal test voltage . 20
6.9 Extreme test conditions . 20
6.9.1 Extreme temperatures . 20
6.9.1.1 Procedure for tests at extreme temperatures . 20
6.9.2 Extreme test voltages . 20
6.9.2.1 Upper extreme test voltage . 20
6.9.2.2 Lower extreme test voltage . 21
7 Environmental tests . 21
7.1 Introduction . 21
7.2 Procedure . 21
7.3 Performance check . 21
7.4 Drop test . 21
7.4.1 Definition . 21
7.4.2 Test conditions . 21
7.4.3 Method of measurement . 22
7.4.4 Requirements . 22
7.5 Temperature tests . 22
7.5.1 Definition . 22
7.5.2 Dry heat test . 22
7.5.2.1 Method of measurement . 22
7.5.2.2 Requirements . 22
7.5.3 Damp heat test . 23
7.5.3.1 Method of measurement . 23
7.5.3.2 Requirements . 23
7.5.4 Low temperature test . 23
7.5.4.1 Method of measurement . 23
7.5.4.2 Requirements . 23
7.5.5 Low temperature battery endurance test . 23
7.5.5.1 Method of measurement . 23
7.5.5.2 Requirements . 24
7.6 Vibration test . 24
7.6.1 Definition . 24
7.6.2 Method of measurement . 24
7.6.3 Requirement . 24
7.7 Corrosion test . 25
7.7.1 Definition . 25
7.7.2 Method of measurement . 25
7.7.3 Requirements . 25
7.8 Thermal shock test. 26
7.8.1 Definition . 26
7.8.2 Method of measurement . 26
7.8.3 Requirements . 26
7.9 Buoyancy test . 26
7.9.1 Definition . 26
7.9.2 Method of measurement . 26
7.9.3 Requirements . 26
7.10 Compass safe distance test . 27
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 098-1 V1.1.1 (2014-02)
7.10.1 Definition . 27
7.10.2 Method of measurement . 27
7.10.3 Requirements . 27
7.11 Solar radiation test . 28
7.11.1 Definition . 28
7.11.2 Method of measurement . 28
7.11.3 Requirements . 28
7.12 Oil resistance test. 28
7.12.1 Definition . 28
7.12.2 Method of measurement . 28
7.12.3 Requirements . 29
7.13 Protection of the transmitter . 29
7.13.1 Definition . 29
7.13.2 Method of measurement . 29
7.13.3 Requirement . 29
8 Tests on the AIS transmitter . 29
8.1 Frequency error . 29
8.1.1 Definition . 29
8.1.2 Method of measurement . 29
8.1.3 Limit . 30
8.2 Conducted Power . 30
8.2.1 Definition . 30
8.2.2 Method of measurement under normal test conditions . 30
8.2.3 Limit . 30
8.3 Maximum Effective Radiated Power (ERP). 30
8.3.1 Definition . 30
8.3.2 Method of measurement . 30
8.3.3 Limits . 31
8.4 Transmitter spectrum mask . 31
8.4.1 Definition . 31
8.4.2 Method of measurement . 31
8.4.3 Limit . 32
8.5 Transmitter transient behaviour (output power) . 32
8.5.1 Definition . 32
8.5.2 Method of measurement . 33
8.5.3 Limit . 34
8.6 Transmitter Transient Behaviour (frequency deviation) . 34
8.6.1 Definition . 34
8.6.2 Method of measurement . 34
8.6.3 Limit . 35
8.7 Synchronization accuracy . 35
8.7.1 Definition . 35
8.7.2 Method of measurement . 35
8.7.3 Limit . 36
8.8 Spurious emissions . 37
8.8.1 Definition . 37
8.8.2 Method of measurement . 37
8.8.3 Limit . 37
9 VDL Link layer tests . 37
9.1 Active mode tests . 37
9.1.1 Method of measurement . 37
9.1.2 Initialization period - Required results. 38
9.1.3 Message content of Message 1 - Required results . 38
9.1.4 Message content of Message 14 - Required results . 38
9.1.5 Transmission schedule for Message 1 - Required results . 38
9.1.6 Communication state of Message 1 - Required results . 39
9.1.7 Transmission schedule of M
...

Draft ETSI EN 303 098-1 V1.1.0 (2013-05)






European Standard
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Maritime low power personal locating beacons employing AIS
Part 1: Technical characteristics and methods of measurement

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 098-1 V1.1.0 (2013-05)



Reference
DEN/ERM-TG26-100-1
Keywords
maritime, radio, SAR, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2013.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 098-1 V1.1.0 (2013-05)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General requirements . 10
4.1 Construction . 10
4.1.1 Categories of equipment . 10
4.2 Controls . 11
4.3 Indicators . 11
4.4 Identifier (user ID). 11
4.5 Labelling. 11
4.6 Instructions . 12
4.7 Power source . 12
4.7.1 Battery requirements . 12
4.7.2 Safety precautions . 12
5 Technical requirements . 13
5.1 General . 13
5.2 AIS transmission characteristics . 13
5.2.1 AIS messages . 13
5.2.1.1 Active mode . 13
5.2.1.2 Training mode . 13
5.2.1.3 Test mode . 14
5.2.2 Synchronization . 14
5.2.2.1 Active and Training modes . 14
5.2.2.2 Test mode . 14
5.2.3 GNSS position source . 14
5.2.3.1 UTC Time . 15
5.2.3.2 Almanac Storage . 15
5.2.4 Required settings . 15
5.2.5 Minimum transmitter performance characteristics . 16
5.2.6 VHF Data Link (VDL) Access . 16
5.2.6.1 Active and Training modes . 16
5.2.6.2 Test mode . 17
5.3 Locating beacon power source . 17
5.3.1 Battery requirements . 17
6 General conditions of measurement . 17
6.1 Conformity testing . 17
6.2 Test Frequencies . 17
6.3 Identifier (user ID). 17
6.4 Artificial Antenna . 17
6.5 Test signals . 18
6.5.1 Standard test signal number 1 . 18
6.5.2 Standard test signal number 2 . 18
6.5.3 Standard test signal number 3 . 18
6.5.4 Reference timing signal . 18
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 098-1 V1.1.0 (2013-05)
6.6 Measurement uncertainty and interpretation of the measured results . 18
6.6.1 Measurement uncertainty . 18
6.6.2 Interpretation of the measurement results . 18
6.7 Test conditions power sources and ambient temperatures . 19
6.7.1 Normal and extreme test conditions. 19
6.7.2 Test power source . 19
6.8 Normal test conditions . 19
6.8.1 Normal temperature and humidity . 19
6.8.2 Normal test voltage . 19
6.9 Extreme test conditions . 19
6.9.1 Extreme temperatures . 19
6.9.1.1 Procedure for tests at extreme temperatures . 19
6.9.2 Extreme test voltages . 20
6.9.2.1 Upper extreme test voltage . 20
6.9.2.2 Lower extreme test voltage . 20
7 Environmental tests . 20
7.1 Introduction . 20
7.2 Procedure . 20
7.3 Performance check . 20
7.4 Drop test . 20
7.4.1 Definition . 20
7.4.2 Test conditions . 20
7.4.3 Method of measurement . 21
7.4.4 Requirements . 21
7.5 Temperature tests . 21
7.5.1 Definition . 21
7.5.2 Dry heat test . 21
7.5.2.1 Method of measurement . 21
7.5.2.2 Requirement . 21
7.5.3 Damp heat test . 22
7.5.3.1 Method of measurement . 22
7.5.3.2 Requirement . 22
7.5.4 Low temperature test . 22
7.5.4.1 Method of measurement . 22
7.5.4.2 Requirement . 22
7.6 Vibration test . 22
7.6.1 Definition . 22
7.6.2 Method of measurement . 22
7.6.3 Requirement . 23
7.7 Corrosion test . 23
7.7.1 Definition . 23
7.7.2 Method of measurement . 23
7.7.3 Requirements . 24
7.8 Thermal shock test. 24
7.8.1 Definition . 24
7.8.2 Method of measurement . 24
7.8.3 Requirements . 24
7.9 Buoyancy test . 24
7.9.1 Definition . 24
7.9.2 Method of measurement . 24
7.9.3 Requirements . 24
7.10 Compass safe distance test . 25
7.10.1 Definition . 25
7.10.2 Method of measurement . 25
7.10.3 Requirements . 25
7.11 Solar radiation test . 26
7.11.1 Definition . 26
7.11.2 Method of measurement . 26
7.11.3 Requirements . 26
7.12 Oil resistance test. 26
7.12.1 Definition . 26
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 098-1 V1.1.0 (2013-05)
7.12.2 Method of measurement . 26
7.12.3 Requirements . 27
7.13 Protection of the transmitter . 27
7.13.1 Definition . 27
7.13.2 Method of measurement . 27
7.13.3 Requirement . 27
8 Tests on the AIS transmitter . 27
8.1 Frequency error . 27
8.1.1 Definition . 27
8.1.2 Method of measurement . 27
8.1.3 Limit . 27
8.2 Conducted Power . 27
8.2.1 Definition . 28
8.2.2 Method of measurement under normal test conditions . 28
8.2.3 Limit . 28
8.3 Maximum Effective Radiated Power (ERP). 28
8.3.1 Definition . 28
8.3.2 Method of measurement . 28
8.3.3 Limits . 29
8.4 Transmitter spectrum mask . 29
8.4.1 Definition . 29
8.4.2 Method of measurement . 29
8.4.3 Limit . 30
8.5 Transmitter transient behaviour (output power) . 30
8.5.1 Definition . 30
8.5.2 Method of measurement . 31
8.5.3 Limit . 32
8.6 Transmitter Transient Behaviour (frequency deviation) . 32
8.6.1 Definition . 32
8.6.2 Method of measurement . 32
8.6.3 Limit . 33
8.7 Synchronization accuracy . 33
8.7.1 Definition . 33
8.7.2 Method of measurement . 33
8.7.3 Limit . 34
8.8 Spurious emissions . 35
8.8.1 Definition . 35
8.8.2 Method of measurement . 35
8.8.3 Limit . 35
9 VDL Link layer tests . 35
9.1 Active mode tests . 35
9.1.1 Method of measurement . 35
9.1.2 Initialization period - Required results. 36
9.1.3 Message content of Message 1 - Required results . 36
9.1.4 Message content of Message 14 - Required results . 36
9.1.5 Transmission schedule for Message 1 - Required results . 36
9.1.6 Communication state of Message 1 - Required results . 37
9.1.7 Transmission schedule of Message 14 - Required results. 37
9.1.8 Transmission with lost GNSS - Required results . 37
9.2 Test mode tests with GNSS data available . 38
9.2.1 Method of measurement . 38
9.2.2 Required results . 38
9.3 Test mode tests without GNSS data available . 38
9.3.1 Method of measurement . 38
9.3.2 Required results . 38
Annex A (normative): Radiated measurements . 39
A.1 Test sites and general arrangements for measurements i
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.