ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard for access to radio spectrum; Part 4: Material Sensing devices; Sub-part 4: Exterior material sensing applications for ground based vehicles
Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard for access to radio spectrum; Part 4: Material Sensing devices; Sub-part 4: Exterior material sensing applications for ground based vehicles
DEN/ERM-TGUWB-601
Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB) tehnologijo - Harmonizirani standard za dostop do radijskega spektra - 4. del: Zaznavala snovi - 4. poddel: Naprave za zaznavanje zunanjih materialov za talna vozila
Ta dokument določa zahteve za tehnične lastnosti in merilne metode za zaznavala snovi z uporabo ultra širokopasovne (UWB) tehnologije za naprave za zaznavanje zunanjih materialov za talna vozila.
Dokument zajema samo zaznavala snovi, ki uporabljajo brezstično ultra širokopasovno tehnologijo v skladu z določili ECC/DEC(07)01 [i.1] in sklepom Komisije 2019/785/EU [i.2].
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.3] je podano v dodatku A.
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 302 065-4-4 V1.1.1 (2022-06)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications
for ground based vehicles
---------------------- Page: 1 ----------------------
2 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 EUT categories . 11
4.2.1 General . 11
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 12
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 13
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 14
4.3.3.3.1 EUT without any active mitigation techniques . 14
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 16
4.3.5 Total Radiated Power (TRP) . 16
4.3.5.1 Applicability. 16
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 17
4.3.6 Listen Before Talk (LBT) . 17
4.3.6.1 Applicability. 17
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 18
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 19
4.4.4 Receiver Baseline Resilience (RBR) . 19
4.4.4.1 Applicability. 19
4.4.4.2 Description . 20
4.4.4.3 Limits . 20
4.4.4.4 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 General conditions for testing . 20
5.3 Conformance test suites . 20
5.3.1 General . 20
5.3.2 EUT orientation and reference points . 21
5.3.3 Test scenarios and setup for transmitter conformance tests . 21
5.4 Conformance methods of measurement for transmitter . 22
5.4.1 Operating Frequency Range (OFR) . 22
5.4.2 Indirect emissions . 23
5.4.2.1 General . 23
5.4.2.2 Considerations for conformance tests for EUT without TRP assessment . 24
5.4.2.3 Considerations for conformance tests for EUT with TRP assessment . 24
5.4.2.4 Common conformance test procedure for TRP . 25
5.4.3 TX unwanted emissions . 25
5.4.4 Total Radiated Power (TRP) . 25
5.4.5 Listen Before Talk (LBT) . 26
5.4.6 Duty Cycle . 26
5.5 Conformance methods of measurement for receiver . 27
5.5.1 General for RDR and RBR conformance tests . 27
5.5.2 Receiver Dynamic Range (RDR) . 27
5.5.2.1 RDR test for EUT designed to analyse the ground below the vehicle . 27
5.5.3 Receiver Baseline Resilience (RBR) . 29
5.5.3.1 RBR test for EUT designed to analyse the ground below the vehicle . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): General conditions for testing, measurement uncertainty and
interpretation of the measurement results . 33
Annex C (normative): Category non-contact-based ground analysing sensor devices . 34
C.1 Description . 34
C.2 Wanted Technical Performance Criteria (WTPC) and RX - requirement . 34
C.2.1 Introduction . 34
C.2.2 Performance criteria for EVS . 34
C.2.3 Justification for missing RX requirements from ETSI EG 203 336 . 35
C.3 Reference ground and sand pit . 36
C.4 Conductive metal plate for measurements . 36
C.4.1 Dimensions of metal cover plate for measurement purposes . 36
C.4.2 Measurement of resistance . 36
C.5 General Measurement setup . 36
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Annex D (normative): Interferer for RBR test . 38
D.1 Interferer requirements for RBR tests . 38
D.1.1 General test frequencies for RBR tests . 38
D.1.2 Test frequencies for EUT with OFR < 500 MHz . 38
D.1.3 Test frequencies for EUT with OFR ≥ 500 MHz . 39
D.1.4 Interferer power levels and modulation . 39
D.2 Interferer test signals for EVS . 40
D.2.1 Interferer test signals . 40
D.2.2 Assessment if no interferer test signal provided at calculated test signals . 41
D.3 List of interferer for RBR test; assessment procedure . 42
D.3.1 General . 42
D.3.2 Assessment list of relevant interferer . 43
D.3.2.1 Considering . 43
D.3.2.2 Several interferer within the same frequency range . 43
D.3.2.3 Interferer overlapping in frequency range . 43
D.3.2.4 Status of interferer . 44
D.3.3 Kind of interferer signal . 44
Annex E (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4, sub-part 4 of a multi-part deliverable. Full details of the entire series can be found in
part 1 [i.13].
National transposition dates
Date of adoption of this EN: 24 May 2022
Date of latest announcement of this EN (doa): 31 August 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2023
Date of withdrawal of any conflicting National Standard (dow): 29 February 2024
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [i.3].
For the case of the present document, the applicable harmonised standard has been ETSI EN 302 065-4 (V1.1.1) [i.8],
for Material Sensing devices using UWB technology below 10,6 GHz which was published in the OJEU without
restriction at 12 April 2017.
In order to consider the above points, ETSI ERM TGUWB decided to develop more specific standards; this means
instead of one generic ETSI EN 302 065-4 [i.8] standard for Material Sensing devices the following standard family
ETSI EN 302 065-4-x for material sensing devices:
• ETSI EN 302 065-4-1: "Material Sensing devices; Sub-part 1: Building material analysis below 10,6 GHz".
• ETSI EN 302 065-4-2: "UWB Material Sensing devices for Security Scanning".
• ETSI EN 302 065-4-3: "Ground humidity and condition sensor".
• ETSI EN 302 065-4-4: "Material Sensing devices; Sub-part 4: Exterior material sensing applications for
ground based vehicles".
• ETSI EN 302 065-4-5: "UWB surveillance devices for parking lot sensors below 10,6 GHz".
NOTE: The above list of standards represents the active work items at the time of finalizing the present document
and the final structure of the ETSI EN 302 065-4-x family may change later.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
1 Scope
The present document specifies the requirements for technical characteristics and methods of measurements for material
sensing applications using UWB technology for external material sensing applications for ground-based vehicles.
The present document only covers non-contact based UWB material sensing devices according to ECC/DEC(07)01 [i.1]
and Commission Decision 2019/785/EU [i.2].
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present docume
...
SLOVENSKI STANDARD
SIST EN 302 065-4-4 V1.1.1:2022
01-september-2022
Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB)
tehnologijo - Harmonizirani standard za dostop do radijskega spektra - 4. del:
Zaznavala snovi - 4. poddel: Naprave za zaznavanje zunanjih materialov za talna
vozila
Short Range Devices (SRD) using Ultra Wide Band technology (UWB) - Harmonised
Standard for access to radio spectrum - Part 4: Material Sensing devices - Sub-part 4 -
Exterior material sensing applications for ground based vehicles
Ta slovenski standard je istoveten z: ETSI EN 302 065-4-4 V1.1.1 (2022-06)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
SIST EN 302 065-4-4 V1.1.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
---------------------- Page: 2 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
ETSI EN 302 065-4-4 V1.1.1 (2022-06)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications
for ground based vehicles
---------------------- Page: 3 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
2 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
3 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 EUT categories . 11
4.2.1 General . 11
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 12
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 13
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 14
4.3.3.3.1 EUT without any active mitigation techniques . 14
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 16
4.3.5 Total Radiated Power (TRP) . 16
4.3.5.1 Applicability. 16
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 17
4.3.6 Listen Before Talk (LBT) . 17
4.3.6.1 Applicability. 17
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 18
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
4 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 19
4.4.4 Receiver Baseline Resilience (RBR) . 19
4.4.4.1 Applicability. 19
4.4.4.2 Description . 20
4.4.4.3 Limits . 20
4.4.4.4 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 General conditions for testing . 20
5.3 Conformance test suites . 20
5.3.1 General . 20
5.3.2 EUT orientation and reference points . 21
5.3.3 Test scenarios and setup for transmitter conformance tests . 21
5.4 Conformance methods of measurement for transmitter . 22
5.4.1 Operating Frequency Range (OFR) . 22
5.4.2 Indirect emissions . 23
5.4.2.1 General . 23
5.4.2.2 Considerations for conformance tests for EUT without TRP assessment . 24
5.4.2.3 Considerations for conformance tests for EUT with TRP assessment . 24
5.4.2.4 Common conformance test procedure for TRP . 25
5.4.3 TX unwanted emissions . 25
5.4.4 Total Radiated Power (TRP) . 25
5.4.5 Listen Before Talk (LBT) . 26
5.4.6 Duty Cycle . 26
5.5 Conformance methods of measurement for receiver . 27
5.5.1 General for RDR and RBR conformance tests . 27
5.5.2 Receiver Dynamic Range (RDR) . 27
5.5.2.1 RDR test for EUT designed to analyse the ground below the vehicle . 27
5.5.3 Receiver Baseline Resilience (RBR) . 29
5.5.3.1 RBR test for EUT designed to analyse the ground below the vehicle . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): General conditions for testing, measurement uncertainty and
interpretation of the measurement results . 33
Annex C (normative): Category non-contact-based ground analysing sensor devices . 34
C.1 Description . 34
C.2 Wanted Technical Performance Criteria (WTPC) and RX - requirement . 34
C.2.1 Introduction . 34
C.2.2 Performance criteria for EVS . 34
C.2.3 Justification for missing RX requirements from ETSI EG 203 336 . 35
C.3 Reference ground and sand pit . 36
C.4 Conductive metal plate for measurements . 36
C.4.1 Dimensions of metal cover plate for measurement purposes . 36
C.4.2 Measurement of resistance . 36
C.5 General Measurement setup . 36
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
5 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Annex D (normative): Interferer for RBR test . 38
D.1 Interferer requirements for RBR tests . 38
D.1.1 General test frequencies for RBR tests . 38
D.1.2 Test frequencies for EUT with OFR < 500 MHz . 38
D.1.3 Test frequencies for EUT with OFR ≥ 500 MHz . 39
D.1.4 Interferer power levels and modulation . 39
D.2 Interferer test signals for EVS . 40
D.2.1 Interferer test signals . 40
D.2.2 Assessment if no interferer test signal provided at calculated test signals . 41
D.3 List of interferer for RBR test; assessment procedure . 42
D.3.1 General . 42
D.3.2 Assessment list of relevant interferer . 43
D.3.2.1 Considering . 43
D.3.2.2 Several interferer within the same frequency range . 43
D.3.2.3 Interferer overlapping in frequency range . 43
D.3.2.4 Status of interferer . 44
D.3.3 Kind of interferer signal . 44
Annex E (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 7 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
6 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4, sub-part 4 of a multi-part deliverable. Full details of the entire series can be found in
part 1 [i.13].
National transposition dates
Date of adoption of this EN: 24 May 2022
Date of latest announcement of this EN (doa): 31 August 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2023
Date of withdrawal of any conflicting National Standard (dow): 29 February 2024
ETSI
---------------------- Page: 8 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
7 ETSI EN 302 065-4-4 V1.1.1 (2022-06)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [i.3].
For the case of the present document, the applicable harmonised standard has been ETSI EN 302 065-4 (V1.1.1) [i.8],
for Material Sensing devices using UWB technology below 10,6 GHz which was published in the OJEU without
restriction at 12 April 2017.
In order to consider the above points, ETSI ERM TGUWB decided to develop more specific standards; this means
instead of one generic ETSI EN 302 065-4 [i.8] standard for Material Sensing devices the following standard family
ETSI EN 302 065-4-x for material sensing devices:
• ETSI EN 302 065-4-1: "Material Sensing devices; Sub-part 1: Building material analysis below 10,6 GHz".
• ETSI EN 302 065-4-2: "UWB Material Sensing devices for Security Scanning".
• ETSI EN 302 065-4-3: "Ground humidity and condition sensor".
• ETSI EN 302 065-4-4: "Material Sensing devices; Sub-part 4: Exterior material sensing applications for
ground based vehicles".
• ETSI EN 302 065-4-5: "UWB surveillance devices for parking lot sensors below 10,6 GHz".
NOTE: The above list of standards represents the active work items at the time of finalizing the present document
and the final structure of the ETSI EN 302 065-4-x family may change later.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 302 065-4-4 V1.1.1:2022
8 ETSI EN 302 06
...
Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications for
ground based vehicles
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 EUT categories . 10
4.2.1 General . 10
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 11
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 12
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 13
4.3.3.3.1 EUT without any active mitigation techniques . 13
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 15
4.3.5 Total Radiated Power (TRP) . 15
4.3.5.1 Applicability. 15
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques. . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 16
4.3.6 Listen Before Talk (LBT) . 16
4.3.6.1 Applicability. 16
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 17
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 19
4.4.4 Receiver Baseline Resilience (RBR) . 19
4.4.4.1 Applicability. 19
4.4.4.2 Description . 19
4.4.4.3 Limits . 20
4.4.4.4 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 General conditions for testing . 20
5.3 Conformance test suites . 20
5.3.1 General . 20
5.3.2 EUT orientation and reference points . 20
5.3.3 Test scenarios and setup for transmitter conformance tests . 21
5.4 Conformance methods of measurement for transmitter . 22
5.4.1 Operating Frequency Range (OFR) . 22
5.4.2 Indirect emissions . 23
5.4.2.1 General . 23
5.4.2.2 Considerations for conformance tests for EUT without TRP assessment: . 24
5.4.2.3 Considerations for conformance tests for EUT with TRP assessment . 24
5.4.2.4 Common conformance test procedure for TRP . 25
5.4.3 TX unwanted emissions . 25
5.4.4 Total Radiated Power (TRP) . 25
5.4.5 Listen Before Talk (LBT) . 26
5.4.6 Duty Cycle . 26
5.5 Conformance methods of measurement for receiver . 27
5.5.1 General for RDR and RBR conformance tests . 27
5.5.2 Receiver Dynamic Range (RDR) . 27
5.5.2.1 RDR test for EUT designed to analyse the ground below the vehicle . 27
5.5.3 Receiver Baseline Resilience (RBR) . 29
5.5.3.1 RBR test for EUT designed to analyse the ground below the vehicle . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): General conditions for testing, measurement uncertainty and
interpretation of the measurement results . 33
Annex C (normative): Category non-contact-based ground analysing sensor devices . 34
C.1 Description . 34
C.2 Wanted Technical Performance Criteria (WTPC) and RX - requirement . 34
C.2.1 Introduction . 34
C.2.2 Performance criteria for EVS . 34
C.2.3 Justification for missing RX requirements from ETSI EG 203 336 . 35
C.3 Reference ground and sand pit . 36
C.4 Conductive metal plate for measurements . 36
C.4.1 Dimensions of metal cover plate for measurement purposes . 36
C.4.2 Measurement of resistance . 36
C.5 General Measurement setup . 36
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Annex D (normative): Interferer for RBR test . 38
D.1 Interferer requirements for RBR tests . 38
D.1.1 General test frequencies for RBR tests . 38
D.1.2 Test frequencies for EUT with OFR < 500 MHz . 38
D.1.3 Test frequencies for EUT with OFR ≥ 500 MHz . 38
D.1.4 Interferer power levels and modulation . 39
D.2 Interferer test signals for EVS . 40
D.2.1 Interferer test signals . 40
D.2.2 Assessment if no interferer test signal provided at calculated test signals . 41
D.3 List of interferer for RBR test; assessment procedure . 42
D.3.1 General . 42
D.3.2 Assessment list of relevant interferer . 43
D.3.2.1 Considering . 43
D.3.2.2 Several interferer within the same frequency range . 43
D.3.2.3 Interferer overlapping in frequency range . 43
D.3.2.4 Status of interferer . 44
D.3.3 Kind of interferer signal . 44
Annex E (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4, subpart 4 of a multi-part deliverable. Full details of the entire series can be found in
part 1 [i.13].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [i.3].
For the case of the present document, the applicable harmonised standard has been ETSI EN 302 065-4 (V1.1.1) [i.8],
for Material Sensing devices using UWB technology below 10,6 GHz which was published in the OJEU without
restriction at 12 April 2017.
In order to consider the above points, ETSI ERM TGUWB decided to develop more specific standards; this means
instead of one generic ETSI EN 302 065-4 [i.8] standard for Material Sensing devices the following standard family
ETSI EN 302 065-4-x for material sensing devices:
• ETSI EN 302 065-4-1: "Material Sensing devices; Sub-part 1: Building material analysis below 10,6 GHz".
• ETSI EN 302 065-4-2: "UWB Material Sensing devices for Security Scanning UWB SSC.
• ETSI EN 302 065-4-3: "Ground humidity and condition sensor".
• ETSI EN 302 065-4-4: "Exterior material sensing applications at ground based vehicles".
• ETSI EN 302 065-4-5: "UWB surveillance devices for parking lot sensors below 10,6 GHz".
NOTE: The above list of standards represents the active work items at the time of finalizing the present document
and the final structure of the ETSI EN 302 065-4-x family may change later.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
1 Scope
The present document specifies the requirements for technical characteristics and methods of measurements for material
sensing applications using UWB technology for external material sensing applications for ground-based vehicles.
The present document only covers non-contact based UWB material sensing devices according to ECC/DEC(07)01 [i.1]
and Commission Decision 2019/785/EU [i.2].
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 303 883-1 (V1.2.1) (02-2021): "Short Range Devices (SRD) and Ultra W
...
SLOVENSKI STANDARD
oSIST prEN 302 065-4-4 V1.1.0:2022
01-april-2022
Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB)
tehnologijo - Harmonizirani standard za dostop do radijskega spektra - 4. del:
Zaznavala snovi - 4. poddel: Naprave za zaznavanje zunanjih materialov za talna
vozila
Short Range Devices (SRD) using Ultra Wide Band technology (UWB) - Harmonised
Standard for access to radio spectrum - Part 4: Material Sensing devices - Sub-part 4 -
Exterior material sensing applications for ground based vehicles
Ta slovenski standard je istoveten z: ETSI EN 302 065-4-4 V1.1.0 (2022-02)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
oSIST prEN 302 065-4-4 V1.1.0:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
---------------------- Page: 2 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB);
Harmonised Standard for access to radio spectrum;
Part 4: Material Sensing devices;
Sub-part 4: Exterior material sensing applications for
ground based vehicles
---------------------- Page: 3 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
2 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Reference
DEN/ERM-TGUWB-601
Keywords
harmonised standard, SRD, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
3 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 EUT categories . 10
4.2.1 General . 10
4.2.2 Categorization by Regulation . 11
4.2.3 Categorization by Modulation . 11
4.2.4 Categorization by Active Mitigation Techniques . 11
4.2.5 Summary EVS EUT sub-categories . 11
4.3 Transmitter requirements . 12
4.3.1 General . 12
4.3.2 Operating Frequency Range (OFR) . 12
4.3.2.1 Applicability. 12
4.3.2.2 Description . 12
4.3.2.3 Limits . 12
4.3.2.4 Conformance . 13
4.3.3 Indirect emissions . 13
4.3.3.1 Applicability. 13
4.3.3.2 Description . 13
4.3.3.3 Limits for indirect emissions . 13
4.3.3.3.1 EUT without any active mitigation techniques . 13
4.3.3.3.2 EUT with active mitigation techniques . 14
4.3.3.4 Conformance . 15
4.3.4 TX unwanted emissions . 15
4.3.4.1 Applicability. 15
4.3.4.2 Description . 15
4.3.4.3 Limits . 15
4.3.4.4 Conformance . 15
4.3.5 Total Radiated Power (TRP) . 15
4.3.5.1 Applicability. 15
4.3.5.2 Description . 16
4.3.5.3 Limits . 16
4.3.5.3.1 Limits for EUT without active mitigation techniques. . 16
4.2.5.3.2 Limits for EUT with active mitigation technique . 16
4.2.5.4 Conformance . 16
4.3.6 Listen Before Talk (LBT) . 16
4.3.6.1 Applicability. 16
4.3.6.2 Description . 17
4.3.6.3 Limits . 17
4.3.6.4 Conformance . 17
4.3.7 Duty Cycle . 17
4.3.7.1 Applicability. 17
4.3.7.2 Description . 17
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
4 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
4.3.7.3 Limits . 18
4.3.7.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Wanted technical performance criteria . 19
4.4.3 Receiver Dynamic Range (RDR) . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 19
4.4.4 Receiver Baseline Resilience (RBR) . 19
4.4.4.1 Applicability. 19
4.4.4.2 Description . 19
4.4.4.3 Limits . 20
4.4.4.4 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 General conditions for testing . 20
5.3 Conformance test suites . 20
5.3.1 General . 20
5.3.2 EUT orientation and reference points . 20
5.3.3 Test scenarios and setup for transmitter conformance tests . 21
5.4 Conformance methods of measurement for transmitter . 22
5.4.1 Operating Frequency Range (OFR) . 22
5.4.2 Indirect emissions . 23
5.4.2.1 General . 23
5.4.2.2 Considerations for conformance tests for EUT without TRP assessment: . 24
5.4.2.3 Considerations for conformance tests for EUT with TRP assessment . 24
5.4.2.4 Common conformance test procedure for TRP . 25
5.4.3 TX unwanted emissions . 25
5.4.4 Total Radiated Power (TRP) . 25
5.4.5 Listen Before Talk (LBT) . 26
5.4.6 Duty Cycle . 26
5.5 Conformance methods of measurement for receiver . 27
5.5.1 General for RDR and RBR conformance tests . 27
5.5.2 Receiver Dynamic Range (RDR) . 27
5.5.2.1 RDR test for EUT designed to analyse the ground below the vehicle . 27
5.5.3 Receiver Baseline Resilience (RBR) . 29
5.5.3.1 RBR test for EUT designed to analyse the ground below the vehicle . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): General conditions for testing, measurement uncertainty and
interpretation of the measurement results . 33
Annex C (normative): Category non-contact-based ground analysing sensor devices . 34
C.1 Description . 34
C.2 Wanted Technical Performance Criteria (WTPC) and RX - requirement . 34
C.2.1 Introduction . 34
C.2.2 Performance criteria for EVS . 34
C.2.3 Justification for missing RX requirements from ETSI EG 203 336 . 35
C.3 Reference ground and sand pit . 36
C.4 Conductive metal plate for measurements . 36
C.4.1 Dimensions of metal cover plate for measurement purposes . 36
C.4.2 Measurement of resistance . 36
C.5 General Measurement setup . 36
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
5 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Annex D (normative): Interferer for RBR test . 38
D.1 Interferer requirements for RBR tests . 38
D.1.1 General test frequencies for RBR tests . 38
D.1.2 Test frequencies for EUT with OFR < 500 MHz . 38
D.1.3 Test frequencies for EUT with OFR ≥ 500 MHz . 38
D.1.4 Interferer power levels and modulation . 39
D.2 Interferer test signals for EVS . 40
D.2.1 Interferer test signals . 40
D.2.2 Assessment if no interferer test signal provided at calculated test signals . 41
D.3 List of interferer for RBR test; assessment procedure . 42
D.3.1 General . 42
D.3.2 Assessment list of relevant interferer . 43
D.3.2.1 Considering . 43
D.3.2.2 Several interferer within the same frequency range . 43
D.3.2.3 Interferer overlapping in frequency range . 43
D.3.2.4 Status of interferer . 44
D.3.3 Kind of interferer signal . 44
Annex E (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
6 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4, subpart 4 of a multi-part deliverable. Full details of the entire series can be found in
part 1 [i.13].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
7 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Directive 2014/53/EU [i.3].
For the case of the present document, the applicable harmonised standard has been ETSI EN 302 065-4 (V1.1.1) [i.8],
for Material Sensing devices using UWB technology below 10,6 GHz which was published in the OJEU without
restriction at 12 April 2017.
In order to consider the above points, ETSI ERM TGUWB decided to develop more specific standards; this means
instead of one generic ETSI EN 302 065-4 [i.8] standard for Material Sensing devices the following standard family
ETSI EN 302 065-4-x for material sensing devices:
• ETSI EN 302 065-4-1: "Material Sensing devices; Sub-part 1: Building material analysis below 10,6 GHz".
• ETSI EN 302 065-4-2: "UWB Material Sensing devices for Security Scanning UWB SSC.
• ETSI EN 302 065-4-3: "Ground humidity and condition sensor".
• ETSI EN 302 065-4-4: "Exterior material sensing applications at ground based vehicles".
• ETSI EN 302 065-4-5: "UWB surveillance devices for parking lot sensors below 10,6 GHz".
NOTE: The above list of standards represents the active work items at the time of finalizing the present document
and the final structure of the ETSI EN 302 065-4-x family may change later.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 302 065-4-4 V1.1.0:2022
8 Draft ETSI EN 302 065-4-4 V1.1.0 (2022-02)
1 Scope
The present document specifies
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.