ETSI EN 300 494-2 V1.2.1 (1999-08)

Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile Test Specification (PTS); Part 2: Profile Specific Test Specification (PSTS) - Portable radio Termination (PT)

REN/DECT-040143-2

Digitalne izboljšane brezvrvične telekomunikacije (DECT) – Profil generičnega dostopa (GAP) – Profil preskušalne specifikacije (PTS) – 2. del: Od profila odvisna preskušalna specifikacija (PSTS) – Prenosna radijska zaključitev (PT)

General Information

• Status: Published
• Publication Date: 23-Aug-1999
• Technical Committee: DECT 4 - DECT Testing aspects
• Current Stage: 12 - Completion
• Due Date: 06-Aug-1999
• Completion Date: 24-Aug-1999
• Mandate: BC-T-341
• Ref Project: SIST EN 300 494-2 V1.2.1:2003 - Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile Test Specification (PTS); Part 2: Profile Specific Test Specification (PSTS) - Portable radio Termination (PT)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.37Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile Test Specification (PTS); Part 2: Profile Specific Test Specification (PSTS) - Portable radio Termination (PT)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:EN 300 494-2 Version 1.2.1SIST EN 300 494-2 V1.2.1:2003en01-december-2003SIST EN 300 494-2 V1.2.1:2003SLOVENSKI
STANDARD



SIST EN 300 494-2 V1.2.1:2003



ETSI EN 300 494-2 V1.2.1 (1999-08)European Standard (Telecommunications series)Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile Test Specification (PTS);Part 2: Profile Specific Test Specification (PSTS) -Portable radio Termination (PT)SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)2ReferenceREN/DECT-040143-2 (4koi0ioo.PDF)KeywordsDECT, GAP, terminal, PTS, testingETSIPostal addressF-06921 Sophia Antipolis Cedex - FRANCEOffice address650 Route des Lucioles - Sophia AntipolisValbonne - FRANCETel.: [phone]
Fax: [phone]Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-Préfecture de Grasse (06) N° 7803/[e-mail] copies of this ETSI deliverablecan be downloaded fromhttp://www.etsi.orgIf you find errors in the present document, send yourcomment to: [e-mail] NotificationNo part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1999.All rights reserved.SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)3ContentsIntellectual Property Rights.6Foreword.61Scope.72References.73Definitions and abbreviations.93.1Definitions.93.2Abbreviations.94Relevant test cases list.104.1Network (NWK) layer.104.1.1Test Suite Structure (TSS).104.1.2Test case index.114.2Data Link Control (DLC) layer.144.2.1Test suite structure.154.2.2Test case index.154.3Medium Access Control (MAC) layer.174.3.1Test suite structure.174.3.2Test case index.184.4Physical (PH) layer.184.4.1Manufacturer declarations.184.4.2Normal Transmitted Power (NTP).194.4.2.1Verdict criteria for IUTs with an integral antenna.194.4.2.2Verdict criteria for IUTs with external antenna connection(s).194.4.3PP radio receiver sensitivity.194.4.4Radio receiver interference performance.194.4.5Receiver intermodulation performance.194.4.6User controlled volume control.195Additional test cases list.205.1Test purposes.205.1.1NWK layer.205.1.2DLC layer.205.1.3MAC layer.205.1.4PH layer.205.2Test cases.205.2.1NWK layer.205.2.2DLC layer.205.2.3MAC layer.205.2.4PH layer.215.2.4.1Receiver sensitivity tolerance of transmitter deviation variations.215.2.4.1.1Definition.215.2.4.1.2Test environment.215.2.4.1.3Method of measurement.215.2.4.1.4Verdict criteria.215.2.4.2Receiver timing tolerance of a PT.225.2.4.2.1Definition.225.2.4.2.2Test environment.225.2.4.2.3Method of measurement, Part 1.225.2.4.2.4Method of measurement, Part 2.235.2.4.2.5Verdict criteria for part 1.235.2.4.2.6Verdict criteria for part 2.235.2.4.3Transmission of Z-field.235.2.4.3.1Definition.235.2.4.3.2Test environment.235.2.4.3.3Method of measurement.24SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)45.2.4.3.4Verdict criteria.24Annex A (normative):Profile Implementation eXtra Information for Testing (PIXIT)proforma.25A.1General.25A.2Profile IXIT Requirements List (XRL).25A.2.1NWK layer protocol.25A.2.2DLC layer protocol.25A.2.3MAC layer protocol.25A.2.4PH layer protocol.25A.3Profile specific IXIT.25A.3.1NWK layer.25A.3.2DLC layer.25A.3.3MAC layer.25A.3.4PH layer.26A.3.5Configuration constraints.26Annex B (normative):Profile Conformance Test Report (PCTR) proforma.27B.1Identification summary.27B.1.1Profile CTR.27B.1.2Implementation Under Test (IUT).27B.1.3Testing environment.28B.1.4Limits and reservations.28B.1.5Comments.28B.2IUT conformance status.28B.3Static conformance summary.29B.4Dynamic conformance summary.29B.5Static conformance review report.29B.6Test campaign report.30B.6.1NWK layer.30B.6.2DLC layer.32B.6.3MAC layer.32B.6.4PH layer.33B.7Observations.33Annex C (normative):System Conformance Test Report (SCTR) proforma.34C.1Identification summary.34C.1.1System Conformance Test Report (SCTR).34C.1.2Test laboratory.34C.1.3Client.35C.1.4System Under Test (SUT).35C.1.5Profile.35C.1.6Nature of conformance testing.36C.1.7Limits and reservations.36C.1.8Record of agreement.36C.1.9Comments.37C.2System report summary.37C.2.1Profile testing summary for GAP NWK layer PT.37C.2.2Profile testing summary for GAP DLC layer PT.38C.2.3Profile testing summary for GAP MAC layer PT.39C.2.4Profile testing summary for GAP PH layer PT.40SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)5Annex D (normative):System Conformance Statement (SCS) proforma.41D.1Identification summary.41D.1.1SCS identification.41D.1.2IUT identification.41D.1.3Client identification.41D.1.4Supplier identification.42D.1.5Manufacturer identification.42D.1.6Protocols identification.43D.1.7Profile identification.43D.2Miscellaneous system information.43D.2.1Configuration.43D.2.2Other information.44History.45SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)6Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be foundin SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respectof ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server(http://www.etsi.org/ipr).Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)which are, or may be, or may become, essential to the present document.ForewordThis European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced CordlessTelecommunications (DECT).The present document is part 2 of a multi-part EN covering the Generic Access Profile (GAP) as identified below:Part 1:"Summary";Part 2:"Profile Specific Test Specification (PSTS) - Portable radio Termination (PT)";Part 3:"Profile Specific Test Specification (PSTS) - Fixed radio Termination (FT)".National transposition datesDate of adoption of this EN:6 August 1999Date of latest announcement of this EN (doa):30 November 1999Date of latest publication of new National Standardor endorsement of this EN (dop/e):31 May 2000Date of withdrawal of any conflicting National Standard (dow):31 May 2000SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)71ScopeThe present document contains the test specification for Digital Enhanced Cordless Telecommunications (DECT)Generic Access Profile (GAP) Portable Part (PP) applications.The main objective of the GAP test specification is to provide approval tests giving a high probability of air interfaceinter-operability between different manufacturer's equipment in different environments (i.e. public, business andresidential).The ISO standard for the methodology of conformance testing ISO/IEC 9646 Parts 1 to 7 [9] to [15] is used as the basisfor the test methodology, and as the basis for the test case specification. This is considered to be unsuitable for Physicallayer testing, and therefore a text description is used.The test cases listed in the present document have been derived from the DECT Common Interface (CI) Test CaseLibrary (TCL) [18] to [26]. In addition as far as the Physical layer is concerned EN 300 176 [16] applies. AdditionalGAP specific test cases are included where required. The Profile IXIT is based on the DECT CI PIXITs specified inEN 300 497 [18] to [26].2ReferencesThe following documents contain provisions which, through reference in this text, constitute provisions of the presentdocument.· References are either specific (identified by date of publication, edition number, version number, etc.) ornon-specific.· For a specific reference, subsequent revisions do not apply.· For a non-specific reference, the latest version applies.· A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the samenumber.[1]EN 300 175-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 1: Overview".[2]EN 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 2: Physical Layer (PHL)".[3]EN 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 3: Medium Access Control (MAC) layer".[4]EN 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 4: Data Link Control (DLC) layer".[5]EN 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 5: Network (NWK) layer".[6]EN 300 175-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 6: Identities and addressing".[7]EN 300 175-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 7: Security features".[8]EN 300 444: "Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile(GAP)".[9]ISO/IEC 9646-1: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 1: General concepts".SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)8[10]ISO/IEC 9646-2: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 2: Abstract test suite specification".[11]ISO/IEC 9646-3: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 3: The Tree and Tabular Combined Notation (TTCN)".[12]ISO/IEC 9646-4: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 4: Test realization".[13]ISO/IEC 9646-5: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 5: Requirements on test laboratories and clients for theConformance Assessment process".[14]ISO/IEC 9646-6: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 6: Protocol Profile Test Specification".[15]ISO/IEC 9646-7: "Information technology - Open Systems Interconnection - Conformance testingmethodology and framework - Part 7: Implementation Conformance Statements".[16]EN 300 176: "Digital Enhanced Cordless Telecommunications (DECT); Approval testspecification".[17]ETS 300 476, Parts 1 to 7: "Digital Enhanced Cordless Telecommunications (DECT); CommonInterface (CI); Protocol Implementation Conformance Statement (PICS) proforma".[18]EN 300 497-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) for MediumAccess Control (MAC) layer".[19]EN 300 497-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Portable radio Termination (PT)".[20]EN 300 497-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 3: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Fixed radio Termination (FT)".[21]EN 300 497-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - Data LinkControl (DLC) layer".[22]EN 300 497-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC) layer".[23]EN 300 497-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 6: Test Suite Structure (TSS) and Test Purposes (TP) - Network(NWK) layer - Portable radio Termination (PT)".[24]EN 300 497-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 7: Abstract Test Suite (ATS) for Network (NWK) layer - Portableradio Termination (PT)".[25]EN 300 497-8: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 8: Test Suite Structure (TSS) and Test Purposes (TP) - Network(NWK) layer - Fixed radio Termination (FT)".[26]EN 300 497-9: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 9: Abstract Test Suite (ATS) for Network (NWK) layer - Fixedradio Termination (FT)".[27]ETS 300 474-1: "Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile(GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS)proforma; Part 1: Portable radio Termination (PT)".SIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)9[27A]ETS 300 474-2: "Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile(GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS)proforma; Part 2: Fixed radio Termination (FT)".[28]EN 300 494-1: "Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile(GAP); Profile Test Specification (PTS); Part 1: Summary".3Definitions and abbreviations3.1DefinitionsFor the purposes of the present document, the following terms and definitions apply:-terms defined in ISO/IEC 9646 Parts 1 to 7 [9] to [15];-definitions in EN 300 175 Parts 1 to 7 [1] to [7];-definitions in EN 300 444 [8].3.2AbbreviationsFor the purposes of the present document, the following abbreviations apply:ACAuthentication CodeATSAbstract Test SuiteBERBit Error RateCCCall ControlCICommon InterfaceDCKDerived Cipher KeyDLCData Link ControlEUTEquipment Under TestFTFixed radio TerminationGAPGeneric Access ProfileICSImplementation Conformance StatementIPUIInternational Portable User IdentityIUTImplementation Under TestIXITImplementation eXtra Information for TestingLCELink Control EntityLLMELower Layer Management EntityLTLower TesterMACMedium Access ControlMMMobility ManagementNLFNew Link FlagNWKNetworkPARKPortable Access Rights KeyPCTRProfile Conformance Test ReportPHPhysicalPICSProtocol Implementation Conformance StatementPIXITProtocol Implementation eXtra Information for TestingPTPortable radio TerminationPSTSProfile Specific Test SpecificationPTSProfile Test SpecificationRFRadio FrequencyRFPRadio Fixed PartSARISecondary Access Rights IdentitySCSSystem Conformance StatementSCTRSystem Conformance Test ReportSIST EN 300 494-2 V1.2.1:2003



ETSIETSI EN 300 494-2 V1.2.1 (1999-08)10SUTSystem Under TestTPUITemporary Portable User IdentityTSTest System4Relevant test cases list4.1Network (NWK) layerThis subclause includes lists of the test groups, and abstract test cases relevant for GAP Profile Test Specification(PTS) - Network (NWK) layer Portable radio Termination (PT) derived from EN 300 497-7 [24].NOTE:References when necessary are given based on the particular test case name unique through all testspecification EN 300 497 [18] to [26].4.1.1Test Suite Structure (TSS)Table 1TSSSuite Name:nwk_ptStandards Ref:EN 300 444 [8]; EN 300 497-7 [24]Profile ICS Ref:ETS 300 474 [27]Profile IXIT Ref:EN 300 494-2Test Method:remoteComments:Test Group ReferenceTest Group ObjectivePT/To check th
...