ETSI TS 101 271 V1.1.1 (2009-01)

Access TerminalsTransmission and Multiplexing (ATTM); Access transmission system on metallic pairs; Very High Speed digital subscriber line system (VDSL2); [ITU-T Recommendation G.993.2 modified]

DTS/ATTM-06003

General Information

• Status: Published
• Publication Date: 06-Jan-2009
• Technical Committee: ATTM TM6 - Wireline Access Network Systems
• Current Stage: 12 - Completion
• Due Date: 17-Dec-2008
• Completion Date: 07-Jan-2009

Standards Content (Sample)

ETSI TS 101 271 V1.1.1 (2009-01)
Technical Specification


Access Terminals Transmission and Multiplexing (ATTM);
Access transmission system on metallic pairs;
Very High Speed digital subscriber line system (VDSL2);
[ITU-T Recommendation G.993.2 modified]

---------------------- Page: 1 ----------------------
2 ETSI TS 101 271 V1.1.1 (2009-01)



Reference
DTS/ATTM-06003
Keywords
VDSL, access, modem, transmission, xDSL
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 101 271 V1.1.1 (2009-01)
Contents
Intellectual Property Rights . 4
Foreword . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions, symbols and abbreviations . 6
3.1 Definitions . 6
3.2 Symbols . 6
3.3 Abbreviations . 6
4 Endorsement notice . 7
5 Global modifications to ITU-T Recommendation G.993.2 . 7
Annex ZA.1 (normative): Test Procedures . 8
ZA.1.1 Test set-up definition . 8
ZA.1.1.1 Signal and noise level definitions . 9
ZA.1.2 Test loops . 9
ZA.1.2.1 Functional description. 9
ZA.1.2.2 Test loop accuracy . 11
ZA.1.3 Impairment generators . 12
ZA.1.3.1 Functional description. 12
ZA.1.3.2 Cable crosstalk models . 13
ZA.1.3.3 Individual impairment generators . 14
ZA.1.3.3.1 NEXT noise generator [G1] . 14
ZA.1.3.3.2 FEXT noise generator [G2] . 15
ZA.1.3.3.3 Background noise generator [G3] . 15
ZA.1.3.3.4 White noise generator [G4] . 15
ZA.1.3.3.5 Broadcast RF noise generator [G5] . 15
ZA.1.3.3.6 Amateur RF noise generator [G6] . 16
ZA.1.3.3.6.1 Specification of Amateur RF noise generator . 17
ZA.1.3.3.7 Impulse noise generator [G7] . 17
ZA.1.3.4 Profile of the individual impairment generators . 18
ZA.1.3.4.1 Frequency domain profiles of generators G1 and G2 . 18
ZA.1.3.4.2 Crosstalk Scenarios . 18
ZA.1.3.4.2.1 Self crosstalk profiles . 18
ZA.1.3.4.2.2 Alien crosstalk profiles . 19
ZA.1.3.5 UPBO testing method . 27
ZA.1.3.5.1 Performance test for UPBO . 27
Annex ZA.2 (normative): Line Constants for Test Loop Set . 28
Annex ZA.3 (informative): Cable Information. 31
Annex ZA.4 (informative): External Systems in the frequency band 0-30MHz. 32
ZA.4.1 Amateur radio bands . 32
ZA.4.2 Other external radio systems . 32
ZA.4.3 Citizens Band (CB) frequencies in Europe . 33
History . 35

ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 101 271 V1.1.1 (2009-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM).
The present document contains information on the European requirements for Very High Speed Digital Subscriber Line
Systems (VDSL2). Unless specifically stated in the present document, the requirements are given in the
ITU-T Specification G.993.2 (Very high speed digital subscriber line transceivers 2) [1].
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 101 271 V1.1.1 (2009-01)
1 Scope
The present document provides the necessary adaptions to ITU-T Recommendation G.993.2 [1] for European
applications and other information relevant to the European environment.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably,
the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the
reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the
method of access to the referenced document and the full network address, with the same punctuation and use of upper
case and lower case letters.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ITU-T Recommendation G.993.2: "Very high speed digital subscriber line transceivers 2
(VDSL2)", February 2006 + Amendments and corrigenda.
[2] ETSI TS 101-388 (V1.4.1): "Access Terminals Transmission and Multiplexing(ATTM); Access
transmission systems on metallic access cables; Asymmetric Digital Subscriber Line (ADSL) -
European specific requirements (ITU-T Recommendation G992.1 modified)".
[3] ITU-T Recommendation G.227: "Conventional Telephone Signal", November 1988.
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] [I-1] ETSI ATTM TM6 Permanent Document TM6(97) 02, June 1998, Cable reference models for
simulating metallic access networks.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 101 271 V1.1.1 (2009-01)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
crest factor (CF): peak to rms voltage ratio
design impedance (RV): target input and output impedance of the VDSL2 modem
NOTE: This is set at 100 Ω in [1].
downstream: transmission in the direction of LT towards NT (network to customer premise)
FTTCab: used to define when VDSL2 LT transceivers are located physically at a node (normally the Cabinet or PCP)
in the periphery of the access network
FTTEx: used to define when VDSL2 LT transceivers are located physically at the serving Local Exchange
reference impedance (RN): chosen impedance used for specifying transmission and reflection characteristics of cables
and test loops
NOTE: ETSI has normalized this value at 135 Ω for a wide range of xDSL performance and conformance tests,
including ADSL tests. This value is considered as being a reasonable average of characteristic
impedances (Z0) observed for a wide range of commonly used European distribution cables.
r.m.s: root mean square value
upstream: transmission in the direction of NT towards LT (customer premise to network)
xDSL: generic term covering the family of all DSL technologies, e.g., HDSL, SDSL, ADSL, VDSL2
3.2 Symbols
For the purposes of the present document, the following symbols apply:
f Test loop calibration frequency for setting the insertion loss of the loop
T
kbps kilo-bits per second
NOTE: 1 kbps = 1 000 bits per second.
Mbps Mega bits per second
NOTE: 1 Mbps = 1 000 kbps.
R Reference Impedance
N
NOTE: Used for specifying transmission and reflection characteristics of cables and
test loops.
R VDSL2 source/load design impedance (purely resistive)
V
Z Characteristic impedance of the test loop
0
Z Compromise reference impedance for the VDSL2 splitter (usually complex)
M
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ADSL Asymmetric DSL
AM Amplitude Modulation
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TS 101 271 V1.1.1 (2009-01)
BER Bit Error Ratio
CF Crest Factor
CO Central Office
CP Customer Premises
DC Direct Current
DSL Digital Subscriber Line (or Loop)
FEXT Far End Cross Talk
FTTCab Fibre To The Cabinet (see definitions)
FTTEx Fibre To The Exchange (see definitions)
HDSL High speed Digital Subscriber Line
HF High Frequency
LT Line Termination
LTU Line Termination Unit
NEXT Near-end crosstalk
NT Network Termination
NOTE: At the customer premise end of the line.
NTU Network Termination Unit
PCP Primary Cross-connection Point
NOTE: Also known as the cabinet.
PDF Probability Density Function
PEP Psophometric Electrical Power
PSD Power Spectral Density
PRBS Pseudo Random Bit Sequence
PVC Poly Vinyl Chloride
RF Radio Frequency
RFI Radio Frequency Interference
RMS Root Mean Square
SDSL Single pair (or Symmetric) Digital Subscriber Line
SW Short Wave
TBD To Be Decided
UPBO Upstream Power Back-Off
VDSL2 Very high speed Digital Subscriber Line 2
NOTE: Specified in ITU-T Recommendation G.993.2 [1].
4 Endorsement notice
All elements of the ITU Recommendation G.993.2 [1] apply. The European specific requirements are given in
ITU-T Recommendation G.993.2 annex B [1].
5 Global modifications to ITU-T Recommendation
G.993.2
Terminology and Nomenclature in Terminology and Nomenclature as Modified by TS 101 271
ITU-T Recommendation G.993.2 [1]
Central Office Network Side
VTU-O LTU
VTU at the Central Office Line Termination Unit
VTU-R NTU
VTU at the Remote End Network Termination Unit

ETSI

---------------------- Page: 7 ----------------------
8 ETSI TS 101 271 V1.1.1 (2009-01)
Annex ZA.1 (normative):
Test Procedures
This clause provides a specification of the test set-up, the insertion path and the definition of signal and noise levels.
The tests focus on the noise margin when VDSL2 signals under test are attenuated by standard test-loops and suffer
interference from standard crosstalk noise or impulse noise. This noise margin indicates what increase of crosstalk noise
or impulse noise level can be tolerated by the VDSL2 system under test before the bit error ratio exceeds the design
target.
ZA.1.1 Test set-up definition
Figure ZA.1 illustrates the functional description of the test set-up. It includes:
15
• A data source capable of generating a Pseudo Random Bit Sequence (PRBS) with a minimum length of 2 -1 to
the transmitter in the direction under test at the bitrate required. The transmitter in the opposite direction shall be
fed with a similar PRBS signal, although there is no need to monitor the receiver output in this path.
• The test loops, as specified in clause ZA.1.2.
• An adding element to add the common mode and differential mode impairment noise (a mix of random,
impulsive and harmonic noise), as specified in clause ZA.1.3.
• An impairment generator, as specified in clause ZA.1.3, to generate both the differential mode and common
mode impairment noise to be fed to the adding element.
• A high impedance and well balanced differential voltage probe (e.g. better than 60 dB across the whole VDSL2
bandwidth) connected with level detectors such as a spectrum analyzer or a true rms voltmeter.
• A high impedance and well balanced common mode voltage probe (e.g. better than 60 dB across the whole
VDSL2 bandwidth) connected with level detectors such as a spectrum analyzer or a true rms voltmeter.
application
application
interface interface
test loop
[A1] [A2]
modem
adding modem
PRBS PRBS
Tx test "cable" Rx
+ splitter
element + splitter
[B1] [B2]
differential voltage voltage
voltage probe probe
probe U U
1 2
impairment level level level
detector detector detector
generator
GND GND

Figure ZA.1: Functional description of the set-up of the performance tests
The two-port characteristics (transfer function, impedance) of the test-loop, as specified in clause ZA.1.2, is defined
between port Tx (node pairs A1, B1) and port Rx (node pair A2, B2). The consequence is that the two-port
characteristics of the test "cable" in figure ZA.1 must be properly adjusted to take full account of non-zero insertion loss
and non-infinite shunt impedance of the adding element and impairment generator. This is to ensure that the insertion of
the generated impairment signals does not appreciably load the line.
The balance about earth, observed at both ports and at the tips of the voltage probe shall exhibit a value that is 10 dB
greater than the transceiver under test. This is to ensure that the impairment generator and monitor function does not
appreciably deteriorate the balance about earth of the transceiver under test.
The signal flow through the test set-up is from port Tx to port Rx, which means that measuring upstream and
downstream performance requires an interchange of transceiver position and test "cable" ends.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI TS 101 271 V1.1.1 (2009-01)
The received signal level at port Rx is the level, measured between node A2 and B2, when port Tx as well as port Rx
are terminated with the VDSL2 transceivers under test. The impairment generator is switched off during this
measurement.
Test Loop #0, as specified in clause ZA.1.2, shall always be used for calibrating and verifying the correct settings of
generators G1-G7, as specified in clause ZA.1.3, during performance testing.
The transmitted signal level at port Tx is the level, measured between node A1 and B1, under the same conditions.
The impairment noise shall be a mix of random, impulsive and harmonic noise, as defined in clause ZA.1.3. The level
that is specified in clause ZA.1.3 is the level at port Rx, measured between node A2 and B2, while port Tx as well as
port Rx are terminated with the design impedance RV. These impedances shall be passive when the transceiver
impedance in the switched-off mode is different from this value.
ZA.1.1.1 Signal and noise level definitions
The signal and noise levels are probed with a well balanced differential voltage probe (U -U ). The differential
2 1
impedance between the tips of that probe shall be higher than the shunt impedance of 100 kΩ in parallel with 10 pF.
Figure ZA.1 shows the probe position when measuring the Rx signal level at the LT or NT receiver. Measuring the Tx
signal level requires the connection of the tips to node pair (A1, B1).
The common mode signal and noise levels are probed with a well balanced common mode voltage probe as the voltage
between nodes A2, B2 and ground. Figure ZA.1 shows the position of the two voltage probes when measuring the
common mode signal. The common mode voltage is defined as 1/2(U +U ).
1 2
NOTE: The various levels (or spectral masks) of signal and noise that are specified in the present document are
defined at the Tx or Rx side of this set-up. The various levels are defined while the set-up is terminated,
as described above, with the design impedance R or with VDSL2 transceivers under test.
V
Probing an rms-voltage Urms (V) in this set-up, over the full signal band, means a power level of
P (dBm) that equals:
2
P = 10 × log (U /R × 1 000) dBm
10 rms V

Probing an rms-voltage Urms (V) in this set-up, within a small frequency band of Δf (in Hertz), means an
average spectral density level of P (dBm/Hz) within that filtered band that equals:
2
P = 10 × log (U /R × 1 000/Δf) (dBm/Hz)
10 rms V

The bandwidth Δf identifies the noise bandwidth of the filter, and not the -3 dB bandwidth.
ZA.1.2 Test loops
The purpose of the test loops shown in figure ZA.2 is to stress VDSL2 transceivers under a wide range of different
conditions that can be expected when deploying VDSL2 in real networks.
ZA.1.2.1 Functional description
The test loops in this clause are an artificial mixture of cable sections. A number of different loops have been used to
represent a wide range of cable impedances, and to represent ripple in amplitude and phase characteristics of the test
loop transfer function.
• The physical length of the individual loops is to be chosen such that the transmission characteristics of all
loops are comparable. This is achieved by normalizing the electrical length of the loops (insertion loss at
300 kHz). The purpose of this is to stress the equalclauser of the VDSL2 modem under test in a similar way
over all loops, when testing at a specific bitrate.
The loops are defined as a combination of cable sections. Each section is defined by means of two-port cable models of
the individual sections (see annex ZA.2). Cable simulators as well as real cables can be used for these sections.
• Loop #0 is a symbolic name for a loop with zero (or near zero) length, to prove that the VDSL2 transceiver
under test can handle the potentially high signal levels when two transceivers are directly interconnected.
ETSI

---------------------- Page: 9 ----------------------
10 ETSI TS 101 271 V1.1.1 (2009-01)
• The impedances of Loop #1 and #2 are nearly constant over a wide frequency interval. These two loops
represent uniform distribution cables, one having a relatively low characteristic impedance and another having
a relatively high impedance (low capacitance per unit length). These impedance values are chosen to be the
lowest and highest values of distribution cables that are commonly used in Europe.
• The impedances of Loop #3 and #4 follow frequency curves that are oscillating in nature. This represents the
mismatch effects in distribution cables caused by a short extent with a cable that differs significantly in
characteristic impedance. Loop #3 represents this at the LT side to stress downstream signals. Loop #4 does
the same at the NT side to stress upstream signals.
Test loops 1 to 4 in figure ZA.2 have equal electrical length (insertion loss at 300 kHz), but differ in input impedance
(see figure ZA.3). It is these values for insertion loss and impedance that define an actual test loop set. This clause only
defines the loop topology – the detailed loop lengths are out of scope for the present document.
LT side (ONU or CO) NT side (CP)
(L0 = 0 m)
Loop #0
100 Ω (L1)
Loop #1
150 Ω (L2)
Loop #2
100 Ω 150 Ω (L3 - Δ L3)
Loop #3
Δ L3
100 Ω (L4 - Δ L4) 180 Ω
Loop #4
Δ L4

Figure ZA.2: Test loop topology
The physical composition of the various test loops is defined in table ZA.1.
Table ZA.1: Test loop composition
Test loop Distribution Extension Extension
cable (L) length
cable (ΔL)
LT or NT side ΔL [m]
#0 - - -
#1 TP100 - -
#2 TP150 - -
#3 TP150 TP100x 70
#4 TP100 TP180x 70
NOTE: The labels "TPxxx" refer to the two-port cable models
specified in annex ZA.2.

The variation of input impedance for the various test loops is shown in figure ZA.3. Some typical transfer functions of
loops #1 to #4 are illustrated in figure ZA.4. The test loops in this example are normalized in electrical length (or
insertion loss) at an arbitrary chosen frequency. Five examples denoted by Q1 to Q5 are shown in figure ZA.4. Loop-set
Q1 has an insertion loss of 55 dB at 2 MHz and loop-set Q5 has an insertion loss of 18,5 dB at 10 MHz. The physical
length of loop-set Q1 is in the range of 1 990 m to 2 100 m and for loop-set Q5 is in the range of 250 m to 300 m. The
plot demonstrates the similarity of the transfer function of all the different loops when they are normalized.
ETSI

---------------------- Page: 10 ----------------------
11 ETSI TS 101 271 V1.1.1 (2009-01)

Figure ZA.3: Calculated variation of input impedance at a normalized loop length of 5 000 m

Figure ZA.4:Typical transfer function (in R =135 Ω)
N
of the test loops when normalized in electrical length
The sections of the loops are defined in annex ZA.2 by means of two-port cable models of the individual sections.
Cable simulators as well as real cables can be used for these sections. To minimize the electrical differences between
test loop configurations, their length is specified as electrical lengths instead of the physical length of the sections in
cascade (meaningful only when real cables are used). The electrical length is equivalent to the insertion loss of the loop
at a given test frequency and termination impedance.
The relationship between electrical length (insertion loss) and total physical length (when real cables are used) can be
calculated from the two-port models given in annex ZA.2.
ZA.1.2.2 Test loop accuracy
The different cable sections are specified by two-port cable models that serve as a representation for real twisted-pair
cables. Cable simulators as well as real cables can be used for these test loops. The associated models and line constants
are specified in annex ZA.2. The composition of the test-loops is specified in table ZA.1.
ETSI

---------------------- Page: 11 ----------------------
12 ETSI TS 101 271 V1.1.1 (2009-01)
The characteristics of each test loop, with cascaded sections, shall approximate the models within a specified accuracy.
This accuracy specification does not hold for the individual sections:
• The magnitude of the test loop insertion loss shall approximate the insertion loss of the specified models within
3 % on a dB scale, between f and the highest frequency of the VDSL2 system for each specific band plan as
0L
defined in table B-1 of ITU-T Recommendation G.993.2 [1]
• The magnitude of the test loop characteristic impedance shall approximate the characteristic impedance of the
specified models within 7 % on a linear scale, between f and the highest frequency of the VDSL2 system for
0L
each specific band plan as defined in table B-1 of ITU-T Recommendation G.993.2 [1].
• The group delay of the test loop shall approximate the group delay of the specified cascaded models within 3 %
on a linear scale, between f and the highest frequency of the VDSL2 system for each specific band plan as
0L
defined in table B-1 of ITU-T Recommendation G.993.2 [1].
• The total length of each loop is to be specified in terms of physical length. The electrical length (insertion loss at
300 kHz) is to be determined from simulation of VDSL2 performance over the test loops. If the implementation
tolerances of a test loop cause the electrical length to be out of
...