ETSI ETS 300 607-1 ed.9 (1998-10)

Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 1: Conformance specification (GSM 11.10-1 version 4.22.1)

RE/SMG-071110PR7-1

Digitalni celični telekomunikacijski sistem (faza 2) - Specifikacija skladnosti mobilne postaje (MS) - 1. del: Specifikacija skladnosti (GSM 11.10-1, različica 4.22.1)

General Information

• Status: Published
• Publication Date: 22-Oct-1998
• Technical Committee: SMG 7 - Mobile Station (MS) Testing
• Current Stage: 12 - Completion
• Due Date: 30-Oct-1998
• Completion Date: 23-Oct-1998
• Mandate: T-247
• Ref Project: SIST ETS 300 607-1 E9:2005 - Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 1: Conformance specification (GSM 11.10-1 version 4.22.1)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ETS 300 607-1 E9:2005
01-februar-2005
'LJLWDOQLFHOLþQLWHOHNRPXQLNDFLMVNLVLVWHPID]D6SHFLILNDFLMDVNODGQRVWL
PRELOQHSRVWDMH06GHO6SHFLILNDFLMDVNODGQRVWL*60UD]OLþLFD

Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS)
conformance specification; Part 1: Conformance specification (GSM 11.10-1 version
4.22.1)
Ta slovenski standard je istoveten z: ETS 300 607-1 Edition 9
ICS:
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
SIST ETS 300 607-1 E9:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ETS 300 607-1 E9:2005

---------------------- Page: 2 ----------------------

SIST ETS 300 607-1 E9:2005
EUROPEAN ETS 300 607-1
TELECOMMUNICATION October 1998
STANDARD Ninth edition
Source: SMG Reference: RE/SMG-071110PR7-1
ICS: 33.020
Key words: Digital cellular telecommunications system, Global System for Mobile Communication (GSM)
R
GLOBAL SYSTEM FOR
MOBILE COMMUNICATIONS
Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 1: Conformance specification
(GSM 11.10-1 version 4.22.1)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: [e-mail] - http://www.etsi.org
Tel.: [phone] - Fax: [phone]
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1998. All rights reserved.

---------------------- Page: 3 ----------------------

SIST ETS 300 607-1 E9:2005
Page 2
ETS 300 607-1 (GSM 11.10-1 version 4.22.1): October 1998
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST ETS 300 607-1 E9:2005
Page 3
ETS 300 607-1 (GSM 11.10-1 version 4.22.1): October 1998
Contents
Foreword . 29
1 Scope. 31
2 Normative references . 31
3 Definitions, conventions, and applicability. 37
3.1 Mobile station definition and configurations. 37
3.2 Applicability. 38
3.2.1 Applicability of this specification. 38
3.2.2 Applicability of the individual tests. 38
3.2.3 Applicability to terminal equipment. 58
3.3 Definitions. 59
3.4 Conventions for mathematical notations . 59
3.4.1 Mathematical signs . 59
3.4.2 Powers to the base 10 . 59
3.5 Conventions on electrical terms . 59
3.5.1 Radio Frequency (RF) input signal level. 59
3.5.2 Reference sensitivity level. 60
3.5.3 Power level of fading signal . 60
3.6 Terms on test conditions . 60
3.6.1 Radio test conditions. 60
4 Test Equipment. 61
4.1 Terms used to describe test equipment in this ETS. 61
4.2 Functional requirements of test equipment . 61
5 Testing methodology in general (layers 1, 2, and 3). 61
5.1 Testing of optional functions and procedures. 61
5.2 Test interfaces and facilities. 61
5.3 Different protocol layers. 62
5.4 Information to be provided by the apparatus supplier . 62
5.5 Definitions of transmit and receive times. 62
6 Reference test methods. 63
6.1 General. 63
6.2 Choice of frequencies in the frequency hopping mode . 63
6.3 "Ideal" radio conditions . 63
6.4 Standard test signals. 63
6.5 Power (control) levels. 63
7 Implicit testing . 64
8 Measurement uncertainty . 64
9 Format of tests. 64
10 Generic call set up procedures . 65
10.1 Generic call set-up procedure for mobile terminating speech calls. 65
10.2 Generic call set-up procedure for mobile originating speech calls. 70
10.3 Generic call set-up procedure for mobile terminating data calls . 73
10.4 Generic call set-up procedure for mobile originating data calls. 76
11 General tests. 80
11.1 Verification of support and non-support of services (multiple numbering scheme or
ISDN). 80

---------------------- Page: 5 ----------------------

SIST ETS 300 607-1 E9:2005
Page 4
ETS 300 607-1 (GSM 11.10-1 version 4.22.1): October 1998
11.1.1 Mobile Terminated (MT) calls.80
11.1.2 Mobile Originated (MO) calls.81
11.2 Verification of support of the single numbering scheme.82
11.3 Verification of non-support of services (Advice of Charge Charging (AoCC)).83
11.4 Verification of non-support of services (call hold).84
11.5 Verification of non-support of services (multiparty).85
11.6 Verification of non-support of feature (Fixed Dialling Number (FDN)).86
11.7 IMEI Security.87
11.8 Coding of the Bearer Capability information element .88
11.8.1 Network to MS Direction.89
11.8.1.1 BS 21 to 26 - Asynchronous Service.89
11.8.1.1.1 BS 21 .89
11.8.1.1.2 BS 22 .93
11.8.1.1.3 BS 24 .93
11.8.1.1.4 BS 25 .93
11.8.1.1.5 BS 26 .93
11.8.1.1.6 BS 23 .93
11.8.1.2 BS 31 to 34 - Synchronous Service.94
11.8.1.2.1 BS 32 .94
11.8.1.2.2 BS 31 .98
11.8.1.2.3 BS 33 .99
11.8.1.2.4 BS 34 .99
11.8.1.3 BS 61 - Alternate Speech / Data.99
11.8.1.3.1 Speech/Asynchronous Data,
Transparent .100
11.8.1.3.2 Speech/Asynchronous Data, Non
Transparent .102
11.8.1.3.3 Speech/Synchronous Data .104
11.8.1.4 BS 81 - Speech followed by Data .105
11.8.1.4.1 Speech followed by Asynchronous
Data .105
11.8.1.4.2 Speech followed by Synchronous
Data .105
11.8.1.5 TS 61 - Alternate Speech / Facsimile group 3.105
11.8.1.5.1 TS 61 - Alternate Speech / Facsimile
group 3, Transparent .106
11.8.1.5.2 TS 61 - Alternate Speech / Facsimile
group 3, Non-Transparent .107
11.8.1.6 TS 62 - Automatic Facsimile group 3 .108
11.8.2 MS to SS direction.108
11.8.2.1 BS 21 to 26 - Asynchronous Service.108
11.8.2.1.1 BS 21 .109
11.8.2.1.2 BS 22 .113
11.8.2.1.3 BS 24 .113
11.8.2.1.4 BS 25 .113
11.8.2.1.5 BS 26 .113
11.8.2.1.6 BS 23 .113
11.8.2.2 BS 31 to 34 - Synchronous Service.114
11.8.2.2.1 BS 32 .114
11.8.2.2.2 BS 31 .118
11.8.2.2.3 BS 33 .119
11.8.2.2.4 BS 34 .119
11.8.2.3 BS 41 to 46 - PAD Access Asynchronous.120
2)
11.8.2.3.1 BS 41.120
11.8.2.3.2 BS 42 .121
11.8.2.3.3 BS 44 .122
11.8.2.3.4 BS 45 .122
11.8.2.3.5 BS 46 .122
11.8.2.3.6 BS 43 .122
11.8.2.4 BS 51 to 53 - Packet Service Synchronous.123
2)
11.8.2.4.1 BS 51.123
11.8.2.4.2 BS 52 .123
11.8.2.4.3 BS 53 .123

---------------------- Page: 6 ----------------------

SIST ETS 300 607-1 E9:2005
Page 5
ETS 300 607-1 (GSM 11.10-1 version 4.22.1): October 1998
11.8.2.5 BS 61 - Alternate Speech / Data . 124
11.8.2.5.1 Speech/Asynchronous Data,
Transparent . 124
11.8.2.5.2 Speech/Asynchronous Data, Non
Transparent . 126
11.8.2.5.3 Speech/Synchronous Data. 128
11.8.2.6 BS 81 - Speech followed by Data. 129
11.8.2.6.1 Speech followed by Asynchronous
Data. 129
11.8.2.6.2 Speech followed by Synchronous
Data. 129
11.8.2.7 TS 61 - Alternate Speech / Facsimile group 3 . 129
11.8.2.7.1 TS 61 - Alternate Speech / Facsimile
group 3, Transparent. 130
11.8.2.7.2 TS 61 - Alternate Speech / Facsimile
group 3, Non Transparent . 131
11.8.2.8 TS 62 - Automatic Facsimile group 3. 132
11.8.2.9 TS 11 and TS 12- Speech. 132
11.8.2.9.1 Support of only full/half rate speech
version 1. 132
11.8.2.9.2 Support of speech full rate version 2
(Enhanced Full Rate). 132
12 Transceiver . 134
12.1 Conducted spurious emissions . 134
12.1.1 MS allocated a channel. 134
12.1.2 MS in idle mode . 135
12.2 Radiated spurious emissions . 137
12.2.1 MS allocated a channel. 137
12.2.2 MS in idle mode . 139
13 Transmitter. 142
13.1 Frequency error and phase error. 142
13.2 Frequency error under multipath and interference conditions. 145
13.3 Transmitter output power and burst timing. 147
13.4 Output RF spectrum. 154
13.5 Intermodulation attenuation. 160
14 Receiver. 162
14.1 Bad frame indication. 168
14.1.1 Bad frame indication - TCH/FS. 168
14.1.1.1 Bad frame indication - TCH/FS - Random RF input. 168
14.1.1.2 Bad frame indication - TCH/FS - Frequency hopping and
downlink DTX . 169
14.1.2 Bad frame indication - TCH/HS . 170
14.1.2.1 Bad frame indication - TCH/HS - Random RF input . 170
14.1.2.2 Bad frame indication - TCH/HS - Frequency hopping and
downlink DTX . 171
14.1.3 Bad frame indication - TCH/FS - Frequency hopping and downlink DTX -
Phase 2 MS in a phase 1 network . 172
14.1.4 Bad frame indication - TCH/HS - Frequency hopping and downlink DTX -
Phase 2 MS in a phase 1 network . 174
14.2 Reference sensitivity . 176
14.2.1 Reference sensitivity - TCH/FS. 176
14.2.2 Reference sensitivity - TCH/HS (Speech frames) . 179
14.2.3 Reference sensitivity - FACCH/F . 181
14.2.4 Reference sensitivity - FACCH/H. 182
14.2.5 Reference sensitivity - full rate data channels . 183
14.2.6 Reference sensitivity - half rate data channels . 184
14.2.7 Reference sensitivity - TCH/EFS . 185
14.3 Usable receiver input level range . 188
14.4 Co-channel rejection. 189
14.4.1 Co-channel rejection - TCH/FS. 189

---------------------- Page: 7 ----------------------

SIST ETS 300 607-1 E9:2005
Page 6
ETS 300 607-1 (GSM 11.10-1 version 4.22.1): October 1998
14.4.2 Co-channel rejection - TCH/HS.191
14.4.3 Co-channel rejection - TCH/HS (SID frames) .193
14.4.4 Co-channel rejection - FACCH/F.195
14.4.5 Co-channel rejection - FACCH/H .196
14.4.6 Co-channel rejection - TCH/EFS.197
14.5 Adjacent channel rejection.198
14.5.1 Adjacent channel rejection - speech channels.198
14.5.2 Adjacent channel rejection - control channels.201
14.6 Intermodulation rejection .203
14.6.1 Intermodulation rejection - speech channels.203
14.6.2 Intermodulation rejection - control channels .204
14.7 Blocking and spurious response.206
14.7.1 Blocking and spurious response - speech channels.206
14.7.2 Blocking and spurious response - control channels.209
14.8 AM suppression .212
14.8.1 AM suppression - speech channels .212
14.8.2 AM suppression - control channels .214
14.9 Paging performance at high input levels.215
15 Timing advance and absolute delay.217
16 Reception time tracking speed.219
17 Access times during handover .221
17.1 Intra cell channel change.221
17.2 Inter cell handover .223
18 Temporary reception gaps .226
19 Channel release after unrecoverable errors.228
19.1 Channel release after unrecoverable errors -1.228
19.2 Channel release after unrecoverable errors - 2.229
19.3 Channel release after unrecoverable errors - 3.230
20 Cell selection and reselection.232
20.1 Cell selection.233
20.2 Cell selection with varying signal strength values.235
20.3 Basic cell reselection .237
20.4 Cell reselection using TEMPORARY_OFFSET, CELL_RESELECT_OFFSET,
POWER_OFFSET and PENALTY_TIME parameters .239
20.5 Cell reselection using parameters transmitted in the System Information type 2bis, type
2ter, type 7 and type 8 messages.241
20.6 Cell reselection timings.243
20.7 Priority of cells.245
20.8 Cell reselection when C1 (serving cell) < 0 for 5 seconds.246
20.9 Running average of the surrounding cell BCCH carrier signal levels .247
20.10 Running average of the serving cell BCCH carrier signal level .248
20.11 Updating the list of six strongest neighbour carriers and decoding the BCCH
information of a new carrier on the list.250
20.12 Decoding the BCCH information of the neighbour carriers on the list of six strongest
neighbour carriers.251
20.13 Decoding the BSIC of the neighbour carriers on the list of six strongest neighbour
carriers.252
20.14 Emergency calls.253
20.15 Cell reselection due to MS rejection "LA not allowed" .254
20.16 Downlink signalling failure.256
20.17 Cell selection if no suitable cell found in 10 s .257
20.18 Cell reselection due to MS rejection "Roaming not allowed in this LA" .258
20.19 Cell selection on release of SDCCH and TCH .259
20.20 Multiband cell selection and reselection .261
20.20.1 Multiband cell selection and reselection / Cell Selection.261
20.20.2 Multiband cell selection and reselection / Cell reselection .263

---------------------- Page: 8 ----------------------

SIST ETS 300 607-1 E9:2005
Page 7
ETS 300 607-1 (GSM 11.10-1 version 4.22.1): October 1998
21 Received signal measurements. 265
21.1 Signal strength. 265
21.2 Signal strength selectivity . 268
21.3 Signal quality under static conditions. 269
21.3.1 Signal quality under static conditions - TCH/FS. 269
21.3.2 Signal quality under static conditions - TCH/HS . 271
21.4 Signal quality under TU50 propagation conditions . 273
22 Transmit power control timing and confirmation. 276
23 Single frequency reference. 277
24 Tests of the layer 1 signalling functions. 278
25 Tests of the layer 2 signalling functions. 279
25.1 Introduction, objective and scope. 279
25.1.1 General . 279
25.1.2 Test configurations. 279
25.1.3 Pre-conditions . 279
25.1.4 Layer 2 test frames . 280
25.1.5 Establishment of the dedicated physical resource. 280
25.1.6 Release of the dedicated physical resource . 281
25.2 Test sequences . 281
25.2.1 Initialization . 282
25.2.1.1 Initialization when contention resolution required. 282
25.2.1.1.1 Normal initialization . 282
25.2.1.1.2 Initialization failure . 283
25.2.1.1.2.1 Loss of UA frame. 283
25.2.1.1.2.2 UA frame with different information
field. 284
25.2.1.1.2.3 Information frame and supervisory
frames in response to an SABM frame285
25.2.1.1.3 Initialization denial . 285
25.2.1.1.4 Total initialization failure . 286
25.2.1.2 Initialization, contention resolution not required . 287
25.2.1.2.1 Normal initialization without contention
resolution. 287
25.2.1.2.2 Initialization failure . 288
25.2.1.2.3 Initialization denial . 290
25.2.1.2.4 Total initialization failure . 290
25.2.2 Normal information transfer . 291
25.2.2.1 Sequence counting and I frame acknowledgements . 291
25.2.2.2 Receipt of an I frame in the timer recovery state . 294
25.2.2.3 Segmentation and concatenation. 296
25.2.3 Normal layer 2 disconnection. 299
25.2.4 Test of link failure. 299
25.2.4.1 I frame loss (MS to SS). 299
25.2.4.2 RR response frame loss (SS to MS). 300
25.2.4.3 RR response frame loss (MS to SS). 301
25.2.5 Test of frame transmission with incorrect C/R values . 302
25.2.5.1 I frame with C bit set
...