ETSI EN 301 489-4 V3.3.1 (2021-02)
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary equipment; Harmonised Standard for ElectroMagnetic Compatibility
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary equipment; Harmonised Standard for ElectroMagnetic Compatibility
REN/ERM-EMC-403
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 4. del: Posebni pogoji za fiksne radijske povezave in pomožno opremo - Harmonizirani standard za elektromagnetno združljivost
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 301 489-4 V3.3.1 (2021-02)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 4: Specific conditions for fixed radio links
and ancillary equipment;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-4 V3.3.1 (2021-02)
Reference
REN/ERM-EMC-403
Keywords
EMC, FWA, harmonised standard, point-to-point,
radio, regulation, RLL, WLL
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-4 V3.3.1 (2021-02)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Test conditions . 8
4.1 General . 8
4.1.1 Introduction. 8
4.1.2 Test conditions and configurations . 8
4.1.3 Emission tests . 9
4.1.4 Immunity tests . 10
4.2 Arrangements for test signals . 11
4.2.1 Arrangements for test signals at the input of the transmitter . 11
4.2.2 Arrangements for test signals at the output of the transmitter . 11
4.2.3 Arrangements for test signals at the input of the receiver . 11
4.2.4 Arrangements for test signals at the output of the receiver . 12
4.3 Exclusion bands . 12
4.3.1 Exclusion bands for receivers . 12
4.3.2 Exclusion bands for transmitters . 12
5 Performance assessment . 12
5.1 Equipment which can provide a communications link . 12
5.2 Ancillary equipment . 12
5.3 Equipment classification . 12
6 Performance criteria . 12
6.0 Introduction . 12
6.1 Performance criterion for Continuous phenomena . 13
6.2 Performance criterion for Transient phenomena . 13
6.3 Specific performance criteria . 13
6.3.1 Digital signal ports . 13
6.3.1.0 General performance criteria . 13
6.3.1.1 Performance criterion for continuous phenomena . 13
6.3.1.2 Performance criterion for transient phenomena . 13
6.3.2 Analogue voice frequency signal ports . 13
6.3.2.1 Performance criterion for continuous phenomena . 13
6.3.2.2 Performance criterion for transient phenomena . 14
6.3.3 Ethernet and packet-data interfaces . 14
6.3.3.0 Introduction . 14
6.3.3.1 Performance criterion for continuous phenomena . 14
6.3.3.2 Performance criterion for transient phenomena . 14
6.3.4 Service and maintenance interfaces . 14
6.3.5 Synchronization interfaces . 14
6.3.5.0 Introduction . 14
6.3.5.1 Performance criterion for continuous phenomena . 14
6.3.5.2 Performance criteria for transient phenomena . 14
6.3.6 Remote alarm interfaces . 14
6.3.6.1 Performance criterion for continuous phenomena . 14
6.3.6.2 Performance criterion for transient phenomena . 15
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-4 V3.3.1 (2021-02)
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 15
7 Applicability overview tables . 15
7.1 Emission . 15
7.1.1 General . 15
7.1.2 Special conditions . 15
7.2 Immunity . 15
7.2.1 General . 15
7.2.2 Special conditions . 16
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 17
Annex B (informative): Change history . 19
History . 20
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-4 V3.3.1 (2021-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
National transposition dates
Date of adoption of this EN: 8 February 2021
Date of latest announcement of this EN (doa): 31 May 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2021
Date of withdrawal of any conflicting National Standard (dow): 30 November 2022
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-4 V3.3.1 (2021-02)
1 Scope
The present document specifies technical characteristics and methods of measurement for Analogue and Digital Fixed
Radio Links operating as fixed Point-to-Point, and Point-to-Multipoint systems as defined in table 1, including the
associated ancillary equipment, in respect of electromagnetic compatibility.
Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum, see
table 1.
Table 1: Radio Technologies in scope of the present document
Technology ETSI Standard
Point-to-Point equipment; intended for operation in the frequency bands from
ETSI EN 302 217-2 [i.5]
1,3 GHz to 86 GHz
Point-to-Multipoint equipment; intended for operation in the frequency band below
ETSI EN 302 326-2 [i.7]
1 GHz and in frequency bands from 1 GHz to 40 GHz
The processing and protection switch, (de)modulator, transmitter, receiver, RF filters, branching networks and feeders
are covered by the present document. The multiplexing and/or de-multiplexing elements are covered if they form part of
the transmitter, receiver and/or transceiver.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
[2] EN 61000-3-3:2013/A1:2019: "Electromagnetic compatibility (EMC) - Part 3-3: Limits -
Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply
systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional
connection", (produced by CENELEC).
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-4 V3.3.1 (2021-02)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] Void.
[i.4] Void.
[i.5] ETSI EN 302 217-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to
86 GHz; Harmonised Standard for access to radio spectrum".
[i.6] Void.
[i.7] ETSI EN 302 326-2: "Fixed Radio Systems; Multipoint Equipment and Antennas; Part 2:
Harmonised Standard for access to radio spectrum".
[i.8] Void.
[i.9] Void.
[i.10] Void.
[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 301 489-1 [1] and the following apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
Base Station (BS): alternative name for Central Station
Central Station (CS): two units comprising of:
• the exchange unit, also called Central Controller Station (CCS) - (interface to the local switch); and
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-4 V3.3.1 (2021-02)
• the radio unit, also called Central Radio Station (CRS) - (central base band/radio transceiver).
NOTE: In some deployments the term Base Station is also used in place of Central Station. For the purposes of
the present document either terms are assumed and are completely interchangeable.
operating frequency range: range(s) of radio frequencies covered by the Equipment Under Test (EUT) without any
change of units
Repeater Station (RS): radio repeater outstations with or without subscriber interfaces
Terminal station (TS): outstations with subscriber interfaces
vehicular equipment: radio equipment intended for installation and use in a vehicle, and powered by the main battery
of the vehicle
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1 [1] and the following apply:
BER Bit Error Ratio
BS Base Station
CCS Central Controller Station
CRS Central Radio Station
CS Central Station
RS Repeater Station
TS Terminal Station
4 Test conditions
4.1 General
4.1.1 Introduction
The test configuration and mode of operation shall represent the intended use and shall be recorded in the test report.
4.1.2 Test conditions and configurations
This clause defines the test conditions and configurations for the emission and immunity tests as follows:
• a transmitter shall, as a minimum, comprise the element between E' and A' of figure 1. Additionally the
transmitter may comprise any of the other elements from the transmitter chain shown in figure 1. If these
additional elements are part of the transmitter or system they shall also meet the requirements of the present
document;
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 489-4 V3.3.1 (2021-02)
Processing
Z'
G' F' E' A' B' C' D'
Tx RF
Branching
Multiplexing & Protection Modulator Transmitter Feeder
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B' to C') does not include a
hybrid.
NOTE 2: Points B' and C' may coincide, dependent on the equipment configuration.
Figure 1: Elements of a transmitter
• a receiver shall, as a minimum, comprise the element between A and E of figure 2. Additionally the receiver
may comprise any of the other elements from the receiver chain shown in figure 2. If these additional elements
are part of the receiver or system they shall also meet the requirements of the present document;
Processing
D C B A E F G Z
Rx RF
Branching
Feeder Receiver Demodulator & Protection Demux
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B to C) does not include a
hybrid.
NOTE 2: Points B and C may coincide, dependent on the equipment configuration.
Figure 2: Elements of a receiver
• a transceiver shall comprise as a minimum the elements E' to A' and A to E shown in figures 1 and 2, and
additionally it may comprise any combinations of the other elements. If these additional elements are part of
the transceiver they shall also meet the requirements of the present document;
• the equipment shall be tested under conditions which are within the manufacturer's declared range of humidity,
temperature and supply voltage;
• the test configuration shall be as close to normal intended use as possible;
• if the equipment is part of a system, or can be connected to ancillary equipment, then it shall be acceptable to
test the equipment while connected to the minimum configuration of ancillary equipment necessary to exercise
the ports;
• ports which in normal operation are connected to ancillary or other equipment shall be either connected to
such equipment, or to a representative termination to simulate the input/output characteristics of the ancillary
or other equipment. Radio Frequency (RF) input/output ports shall be correctly terminated;
• if the equipment has a large number of ports, then a sufficient number shall be selected to simulate actual
operation conditions and to ensure that all the different types of termination are tested;
• ports which are not connected to cables during normal intended operation, e.g. service connectors,
programming connectors, temporary connectors, etc. shall not be connected to any cables for the purpose of
ElectroMagnetic Compatibility (EMC) testing. Where cables have to be connected to these ports, or
interconnecting cables have to be extended in length in order to exercise the EUT, precautions shall be taken to
ensure that the evaluation of the EUT is not affected by the addition or extension of these cables;
• the test conditions, test configuration and mode of operation shall be recorded in the test report.
4.1.3 Emission tests
For Point-to-Multipoint systems a communications link shall be established, which shall comprise of the Central Station
and a minimum of one Terminal Station. These stations are tested separately.
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 301 489-4 V3.3.1 (2021-02)
4.1.4 Immunity tests
The test configuration shall for transmitters be in accordance with the principle of figure 3, and for receivers it shall be
in accordance with the principle of figure 4, and for transceiver shall be in accordance with the principle of figure 5.
The monitoring equipment shall be located outside the test environment. Adequate measures shall be taken to avoid any
effects of the test signals on the monitoring equipment.
Figure 3: Test configuration for transmitters
During immunity tests the transmitter shall be operated at its rated output power. The input to the transmitter shall be in
accordance with clause 4.2.1 (see figure 3). A communication link shall be established at the start of the test and be
maintained during the test.
Outside test environment
Inside test environment
RF input
Output
Signal
Attenuator Transmitter
Receiver
source
Monitoring
equipment
Figure 4: Test configuration for receivers
During immunity tests for receivers, the wanted RF input signal, coupled to the receiver, shall be in accordance with
clause 4.2.3 (see figure 4). A communication link shall be established at the start of the test and be maintained during
the test.
Inside test environment Outside test environment
RF output
Input
Receiver Monitoring
Transmitter Attenuator
equipment
RF input
Output
Signal
Receiver Attenuator Transmitter
source
Figure 5: Test configuration of transceivers
ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 301 489-4 V3.3.1 (2021-02)
In the case of duplex transceivers where the transmitter and receiver cannot operate at the same radio frequency, the
wanted input signal, coupled to the receiver, shall be in accordance with clause 4.2.3. The transmitter shall be operated
at its rated output power, and with its input coupled to the output of the receiver (repeater mode) (see figure 5).
The same test configuration also applies where the transmitters and receivers operate at the same radio frequency.
The measurement shall be made in the mode of operation as required in this clause.
A communication link shall be established at the start of the test and be maintained during the test.
For the immunity tests of ancillary equipment without a separate pass/fail criteria, the receiver, transmitter or
transceiver coupled to the ancillary equipment, shall be used to judge whether the ancillary equipment passes or fails.
For Point-to-Multipoint systems the minimum configuration shall comprise of one Central Station and one terminal
station, unless more terminal stations are required to establish a representative test configuration.
A communication link shall be established at the start of the test and maintained during the test, between the Central
Station and the Terminal Station.
These stations are tested separately.
4.2 A
...
SLOVENSKI STANDARD
SIST EN 301 489-4 V3.3.1:2021
01-april-2021
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 4.
del: Posebni pogoji za fiksne radijske povezave in pomožno opremo -
Harmonizirani standard za elektromagnetno združljivost
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 4:
Specific conditions for fixed radio links and ancillary equipment - Harmonised Standard
for electromagnetic compatibility
Ta slovenski standard je istoveten z: ETSI EN 301 489-4 V3.3.1 (2021-02)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 301 489-4 V3.3.1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 301 489-4 V3.3.1:2021
---------------------- Page: 2 ----------------------
SIST EN 301 489-4 V3.3.1:2021
ETSI EN 301 489-4 V3.3.1 (2021-02)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 4: Specific conditions for fixed radio links
and ancillary equipment;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 3 ----------------------
SIST EN 301 489-4 V3.3.1:2021
2 ETSI EN 301 489-4 V3.3.1 (2021-02)
Reference
REN/ERM-EMC-403
Keywords
EMC, FWA, harmonised standard, point-to-point,
radio, regulation, RLL, WLL
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 489-4 V3.3.1:2021
3 ETSI EN 301 489-4 V3.3.1 (2021-02)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Test conditions . 8
4.1 General . 8
4.1.1 Introduction. 8
4.1.2 Test conditions and configurations . 8
4.1.3 Emission tests . 9
4.1.4 Immunity tests . 10
4.2 Arrangements for test signals . 11
4.2.1 Arrangements for test signals at the input of the transmitter . 11
4.2.2 Arrangements for test signals at the output of the transmitter . 11
4.2.3 Arrangements for test signals at the input of the receiver . 11
4.2.4 Arrangements for test signals at the output of the receiver . 12
4.3 Exclusion bands . 12
4.3.1 Exclusion bands for receivers . 12
4.3.2 Exclusion bands for transmitters . 12
5 Performance assessment . 12
5.1 Equipment which can provide a communications link . 12
5.2 Ancillary equipment . 12
5.3 Equipment classification . 12
6 Performance criteria . 12
6.0 Introduction . 12
6.1 Performance criterion for Continuous phenomena . 13
6.2 Performance criterion for Transient phenomena . 13
6.3 Specific performance criteria . 13
6.3.1 Digital signal ports . 13
6.3.1.0 General performance criteria . 13
6.3.1.1 Performance criterion for continuous phenomena . 13
6.3.1.2 Performance criterion for transient phenomena . 13
6.3.2 Analogue voice frequency signal ports . 13
6.3.2.1 Performance criterion for continuous phenomena . 13
6.3.2.2 Performance criterion for transient phenomena . 14
6.3.3 Ethernet and packet-data interfaces . 14
6.3.3.0 Introduction . 14
6.3.3.1 Performance criterion for continuous phenomena . 14
6.3.3.2 Performance criterion for transient phenomena . 14
6.3.4 Service and maintenance interfaces . 14
6.3.5 Synchronization interfaces . 14
6.3.5.0 Introduction . 14
6.3.5.1 Performance criterion for continuous phenomena . 14
6.3.5.2 Performance criteria for transient phenomena . 14
6.3.6 Remote alarm interfaces . 14
6.3.6.1 Performance criterion for continuous phenomena . 14
6.3.6.2 Performance criterion for transient phenomena . 15
ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 489-4 V3.3.1:2021
4 ETSI EN 301 489-4 V3.3.1 (2021-02)
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 15
7 Applicability overview tables . 15
7.1 Emission . 15
7.1.1 General . 15
7.1.2 Special conditions . 15
7.2 Immunity . 15
7.2.1 General . 15
7.2.2 Special conditions . 16
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 17
Annex B (informative): Change history . 19
History . 20
ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 489-4 V3.3.1:2021
5 ETSI EN 301 489-4 V3.3.1 (2021-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
National transposition dates
Date of adoption of this EN: 8 February 2021
Date of latest announcement of this EN (doa): 31 May 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2021
Date of withdrawal of any conflicting National Standard (dow): 30 November 2022
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 489-4 V3.3.1:2021
6 ETSI EN 301 489-4 V3.3.1 (2021-02)
1 Scope
The present document specifies technical characteristics and methods of measurement for Analogue and Digital Fixed
Radio Links operating as fixed Point-to-Point, and Point-to-Multipoint systems as defined in table 1, including the
associated ancillary equipment, in respect of electromagnetic compatibility.
Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum, see
table 1.
Table 1: Radio Technologies in scope of the present document
Technology ETSI Standard
Point-to-Point equipment; intended for operation in the frequency bands from
ETSI EN 302 217-2 [i.5]
1,3 GHz to 86 GHz
Point-to-Multipoint equipment; intended for operation in the frequency band below
ETSI EN 302 326-2 [i.7]
1 GHz and in frequency bands from 1 GHz to 40 GHz
The processing and protection switch, (de)modulator, transmitter, receiver, RF filters, branching networks and feeders
are covered by the present document. The multiplexing and/or de-multiplexing elements are covered if they form part of
the transmitter, receiver and/or transceiver.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
[2] EN 61000-3-3:2013/A1:2019: "Electromagnetic compatibility (EMC) - Part 3-3: Limits -
Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply
systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional
connection", (produced by CENELEC).
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 489-4 V3.3.1:2021
7 ETSI EN 301 489-4 V3.3.1 (2021-02)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] Void.
[i.4] Void.
[i.5] ETSI EN 302 217-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to
86 GHz; Harmonised Standard for access to radio spectrum".
[i.6] Void.
[i.7] ETSI EN 302 326-2: "Fixed Radio Systems; Multipoint Equipment and Antennas; Part 2:
Harmonised Standard for access to radio spectrum".
[i.8] Void.
[i.9] Void.
[i.10] Void.
[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 301 489-1 [1] and the following apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
Base Station (BS): alternative name for Central Station
Central Station (CS): two units comprising of:
• the exchange unit, also called Central Controller Station (CCS) - (interface to the local switch); and
ETSI
---------------------- Page: 9 ----------------------
SIST EN 301 489-4 V3.3.1:2021
8 ETSI EN 301 489-4 V3.3.1 (2021-02)
• the radio unit, also called Central Radio Station (CRS) - (central base band/radio transceiver).
NOTE: In some deployments the term Base Station is also used in place of Central Station. For the purposes of
the present document either terms are assumed and are completely interchangeable.
operating frequency range: range(s) of radio frequencies covered by the Equipment Under Test (EUT) without any
change of units
Repeater Station (RS): radio repeater outstations with or without subscriber interfaces
Terminal station (TS): outstations with subscriber interfaces
vehicular equipment: radio equipment intended for installation and use in a vehicle, and powered by the main battery
of the vehicle
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1 [1] and the following apply:
BER Bit Error Ratio
BS Base Station
CCS Central Controller Station
CRS Central Radio Station
CS Central Station
RS Repeater Station
TS Terminal Station
4 Test conditions
4.1 General
4.1.1 Introduction
The test configuration and mode of operation shall represent the intended use and shall be recorded in the test report.
4.1.2 Test conditions and configurations
This clause defines the test conditions and configurations for the emission and immunity tests as follows:
• a transmitter shall, as a minimum, comprise the element between E' and A' of figure 1. Additionally the
transmitter may comprise any of the other elements from the transmitter chain shown in figure 1. If these
additional elements are part of the transmitter or system they shall also meet the requirements of the present
document;
ETSI
---------------------- Page: 10 ----------------------
SIST EN 301 489-4 V3.3.1:2021
9 ETSI EN 301 489-4 V3.3.1 (2021-02)
Processing
Z'
G' F' E' A' B' C' D'
Tx RF
Branching
Multiplexing & Protection Modulator Transmitter Feeder
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B' to C') does not include a
hybrid.
NOTE 2: Points B' and C' may coincide, dependent on the equipment configuration.
Figure 1: Elements of a transmitter
• a receiver shall, as a minimum, comprise the element between A and E of figure 2. Additionally the receiver
may comprise any of the other elements from the receiver chain shown in figure 2. If these additional elements
are part of the receiver or system they shall also meet the requirements of the present document;
Processing
D C B A E F G Z
Rx RF
Branching
Feeder Receiver Demodulator & Protection Demux
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B to C) does not include a
hybrid.
NOTE 2: Points B and C may coincide, dependent on the equipment configuration.
Figure 2: Elements of a receiver
• a transceiver shall comprise as a minimum the elements E' to A' and A to E shown in figures 1 and 2, and
additionally it may comprise any combinations of the other elements. If these additional elements are part of
the transceiver they shall also meet the requirements of the present document;
• the equipment shall be tested under conditions which are within the manufacturer's declared range of humidity,
temperature and supply voltage;
• the test configuration shall be as close to normal intended use as possible;
• if the equipment is part of a system, or can be connected to ancillary equipment, then it shall be acceptable to
test the equipment while connected to the minimum configuration of ancillary equipment necessary to exercise
the ports;
• ports which in normal operation are connected to ancillary or other equipment shall be either connected to
such equipment, or to a representative termination to simulate the input/output characteristics of the ancillary
or other equipment. Radio Frequency (RF) input/output ports shall be correctly terminated;
• if the equipment has a large number of ports, then a sufficient number shall be selected to simulate actual
operation conditions and to ensure that all the different types of termination are tested;
• ports which are not connected to cables during normal intended operation, e.g. service connectors,
programming connectors, temporary connectors, etc. shall not be connected to any cables for the purpose of
ElectroMagnetic Compatibility (EMC) testing. Where cables have to be connected to these ports, or
interconnecting cables have to be extended in length in order to exercise the EUT, precautions shall be taken to
ensure that the evaluation of the EUT is not affected by the addition or extension of these cables;
• the test conditions, test configuration and mode of operation shall be recorded in the test report.
4.1.3 Emission tests
For Point-to-Multipoint systems a communications link shall be established, which shall comprise of the Central Station
and a minimum of one Terminal Station. These stations are tested separately.
ETSI
---------------------- Page: 11 ----------------------
SIST EN 301 489-4 V3.3.1:2021
10 ETSI EN 301 489-4 V3.3.1 (2021-02)
4.1.4 Immunity tests
The test configuration shall for transmitters be in accordance with the principle of figure 3, and for receivers it shall be
in accordance with the principle of figure 4, and for transceiver shall be in accordance with the principle of figure 5.
The monitoring equipment shall be located outside the test environment. Adequate measures shall be taken to avoid any
effects of the test signals on the monitoring equipment.
Figure 3: Test configuration for transmitters
During immunity tests the transmitter shall be operated at its rated output power. The input to the transmitter shall be in
accordance with clause 4.2.1 (see figure 3). A communication link shall be established at the start of the test and be
maintained during the test.
Outside test environment
Inside test environment
RF input
Output
Signal
Attenuator Transmitter
Receiver
source
Monitoring
equipment
Figure 4: Test configuration for receivers
During immunity tests for receivers, the wanted RF input signal, coupled to the receiver, shall be in accordance with
clause 4.2.3 (see figure 4). A communication link shall be established at the start of the test and be maintained during
the test.
Inside test environment Outside test environment
RF output
Input
Receiver Monitoring
Transmitter Attenuator
equipment
RF input
Output
Signal
Receiver Attenuator Transmitter
source
Figure 5: Test configuration of transceivers
ETSI
---------------------- Page: 12 ----------------------
SIST EN 3
...
Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 4: Specific conditions for fixed radio links
and ancillary equipment;
Harmonised Standard for ElectroMagnetic Compatibility
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
Reference
REN/ERM-EMC-403
Keywords
EMC, FWA, harmonised standard, point-to-point,
radio, regulation, RLL, WLL
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Test conditions . 8
4.1 General . 8
4.1.1 Introduction. 8
4.1.2 Test conditions and configurations . 8
4.1.3 Emission tests . 9
4.1.4 Immunity tests . 10
4.2 Arrangements for test signals . 11
4.2.1 Arrangements for test signals at the input of the transmitter . 11
4.2.2 Arrangements for test signals at the output of the transmitter . 11
4.2.3 Arrangements for test signals at the input of the receiver . 11
4.2.4 Arrangements for test signals at the output of the receiver . 12
4.3 Exclusion bands . 12
4.3.1 Exclusion bands for receivers . 12
4.3.2 Exclusion bands for transmitters . 12
5 Performance assessment . 12
5.1 Equipment which can provide a communications link . 12
5.2 Ancillary equipment . 12
5.3 Equipment classification . 12
6 Performance criteria . 12
6.0 Introduction . 12
6.1 Performance criterion for Continuous phenomena . 13
6.2 Performance criterion for Transient phenomena . 13
6.3 Specific performance criteria . 13
6.3.1 Digital signal ports . 13
6.3.1.0 General performance criteria . 13
6.3.1.1 Performance criterion for continuous phenomena . 13
6.3.1.2 Performance criterion for transient phenomena . 13
6.3.2 Analogue voice frequency signal ports . 13
6.3.2.1 Performance criterion for continuous phenomena . 13
6.3.2.2 Performance criterion for transient phenomena . 14
6.3.3 Ethernet and packet-data interfaces . 14
6.3.3.0 Introduction . 14
6.3.3.1 Performance criterion for continuous phenomena . 14
6.3.3.2 Performance criterion for transient phenomena . 14
6.3.4 Service and maintenance interfaces . 14
6.3.5 Synchronization interfaces . 14
6.3.5.0 Introduction . 14
6.3.5.1 Performance criterion for continuous phenomena . 14
6.3.5.2 Performance criteria for transient phenomena . 14
6.3.6 Remote alarm interfaces . 14
6.3.6.1 Performance criterion for continuous phenomena . 14
6.3.6.2 Performance criterion for transient phenomena . 15
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 15
7 Applicability overview tables . 15
7.1 Emission . 15
7.1.1 General . 15
7.1.2 Special conditions . 15
7.2 Immunity . 15
7.2.1 General . 15
7.2.2 Special conditions . 16
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 17
Annex B (informative): Change history . 19
History . 20
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
1 Scope
The present document specifies technical characteristics and methods of measurement for Analogue and Digital Fixed
Radio Links operating as fixed Point-to-Point, and Point-to-Multipoint systems as defined in table 1, including the
associated ancillary equipment, in respect of electromagnetic compatibility.
Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum, see
table 1.
Table 1: Radio Technologies in scope of the present document
Technology ETSI Standard
Point-to-Point equipment; intended for operation in the frequency bands from
ETSI EN 302 217-2 [i.5]
1,3 GHz to 86 GHz
Point-to-Multipoint equipment; intended for operation in the frequency band below
ETSI EN 302 326-2 [i.7]
1 GHz and in frequency bands from 1 GHz to 40 GHz
The processing and protection switch, (de)modulator, transmitter, receiver, RF filters, branching networks and feeders
are covered by the present document. The multiplexing and/or de-multiplexing elements are covered if they form part of
the transmitter, receiver and/or transceiver.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
[2] EN 61000-3-3:2013/A1:2019: "Electromagnetic compatibility (EMC) - Part 3-3: Limits -
Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply
systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional
connection", (produced by CENELEC).
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] Void.
[i.4] Void.
[i.5] ETSI EN 302 217-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to
86 GHz; Harmonised Standard for access to radio spectrum".
[i.6] Void.
[i.7] ETSI EN 302 326-2: "Fixed Radio Systems; Multipoint Equipment and Antennas; Part 2:
Harmonised Standard for access to radio spectrum".
[i.8] Void.
[i.9] Void.
[i.10] Void.
[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 301 489-1 [1] and the following apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
Base Station (BS): alternative name for Central Station
Central Station (CS): two units comprising of:
• the exchange unit, also called Central Controller Station (CCS) - (interface to the local switch); and
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
• the radio unit, also called Central Radio Station (CRS) - (central base band/radio transceiver).
NOTE: In some deployments the term Base Station is also used in place of Central Station. For the purposes of
the present document either terms are assumed and are completely interchangeable.
operating frequency range: range(s) of radio frequencies covered by the Equipment Under Test (EUT) without any
change of units
Repeater Station (RS): radio repeater outstations with or without subscriber interfaces
Terminal station (TS): outstations with subscriber interfaces
vehicular equipment: radio equipment intended for installation and use in a vehicle, and powered by the main battery
of the vehicle
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1 [1] and the following apply:
BER Bit Error Ratio
BS Base Station
CCS Central Controller Station
CRS Central Radio Station
CS Central Station
RS Repeater Station
TS Terminal Station
4 Test conditions
4.1 General
4.1.1 Introduction
The test configuration and mode of operation shall represent the intended use and shall be recorded in the test report.
4.1.2 Test conditions and configurations
This clause defines the test conditions and configurations for the emission and immunity tests as follows:
• a transmitter shall, as a minimum, comprise the element between E' and A' of figure 1. Additionally the
transmitter may comprise any of the other elements from the transmitter chain shown in figure 1. If these
additional elements are part of the transmitter or system they shall also meet the requirements of the present
document;
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
Processing
Z'
G' F' E' A' B' C' D'
Tx RF
Branching
Multiplexing & Protection Modulator Transmitter Feeder
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B' to C') does not include a
hybrid.
NOTE 2: Points B' and C' may coincide, dependent on the equipment configuration.
Figure 1: Elements of a transmitter
• a receiver shall, as a minimum, comprise the element between A and E of figure 2. Additionally the receiver
may comprise any of the other elements from the receiver chain shown in figure 2. If these additional elements
are part of the receiver or system they shall also meet the requirements of the present document;
Processing
D C B A E F G Z
Rx RF
Branching
Feeder Receiver Demodulator & Protection Demux
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B to C) does not include a
hybrid.
NOTE 2: Points B and C may coincide, dependent on the equipment configuration.
Figure 2: Elements of a receiver
• a transceiver shall comprise as a minimum the elements E' to A' and A to E shown in figures 1 and 2, and
additionally it may comprise any combinations of the other elements. If these additional elements are part of
the transceiver they shall also meet the requirements of the present document;
• the equipment shall be tested under conditions which are within the manufacturer's declared range of humidity,
temperature and supply voltage;
• the test configuration shall be as close to normal intended use as possible;
• if the equipment is part of a system, or can be connected to ancillary equipment, then it shall be acceptable to
test the equipment while connected to the minimum configuration of ancillary equipment necessary to exercise
the ports;
• ports which in normal operation are connected to ancillary or other equipment shall be either connected to
such equipment, or to a representative termination to simulate the input/output characteristics of the ancillary
or other equipment. Radio Frequency (RF) input/output ports shall be correctly terminated;
• if the equipment has a large number of ports, then a sufficient number shall be selected to simulate actual
operation conditions and to ensure that all the different types of termination are tested;
• ports which are not connected to cables during normal intended operation, e.g. service connectors,
programming connectors, temporary connectors, etc. shall not be connected to any cables for the purpose of
ElectroMagnetic Compatibility (EMC) testing. Where cables have to be connected to these ports, or
interconnecting cables have to be extended in length in order to exercise the EUT, precautions shall be taken to
ensure that the evaluation of the EUT is not affected by the addition or extension of these cables;
• the test conditions, test configuration and mode of operation shall be recorded in the test report.
4.1.3 Emission tests
For Point-to-Multipoint systems a communications link shall be established, which shall comprise of the Central Station
and a minimum of one Terminal Station. These stations are tested separately.
ETSI
---------------------- Page: 9 ----------------------
10 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
4.1.4 Immunity tests
The test configuration shall for transmitters be in accordance with the principle of figure 3, and for receivers it shall be
in accordance with the principle of figure 4, and for transceiver shall be in accordance with the principle of figure 5.
The monitoring equipment shall be located outside the test environment. Adequate measures shall be taken to avoid any
effects of the test signals on the monitoring equipment.
Figure 3: Test configuration for transmitters
During immunity tests the transmitter shall be operated at its rated output power. The input to the transmitter shall be in
accordance with clause 4.2.1 (see figure 3). A communication link shall be established at the start of the test and be
maintained during the test.
Outside test environment
Inside test environment
RF input
Output
Signal
Attenuator Transmitter
Receiver
source
Monitoring
equipment
Figure 4: Test configuration for receivers
During immunity tests for receivers, the wanted RF input signal, coupled to the receiver, shall be in accordance with
clause 4.2.3 (see figure 4). A communication link shall be established at the start of the test and be maintained during
the test.
Inside test environment Outside test environment
RF output
Input
Receiver Monitoring
Transmitter Attenuator
equipment
RF input
Output
Signal
Receiver Attenuator Transmitter
source
Figure 5: Test configuration of transceivers
ETSI
---------------------- Page: 10 ----------------------
11 Final draft ETSI EN 301 489-4 V3.3.1 (2020-12)
In the case of duplex transceivers where the transmitter and receiver cannot operate at the same radio frequency, the
wanted input signal, coupled to the receiver, shall be in accordance with clause 4.2.3. The transmitter shall be operated
at its rated output power, and with its input coupled to the output of the receiver (repeater mode) (see figure 5).
The same test configuration also applies where the transmitters and receivers operate at the same radio frequency.
The measurement shall be made in the mode of operation as required in this clause.
A communication link shall be established at the start of the test and be maintained during the test.
For the immunity tests of ancillary equipment without a separate pass/fail criteria, the receiver, transmitter or
transceiver coupled to the ancillary equipment, shall be used to judge whether the ancillary equipment passes or fails.
For Point-to-Multipoint systems the minimum configuration shall comprise of one Central Station and one terminal
station, unless more terminal stations are required to establish a representative t
...
Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 4: Specific conditions for fixed radio links
and ancillary equipment;
Harmonised Standard for electromagnetic compatibility
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Reference
REN/ERM-EMC-403
Keywords
EMC, FWA, harmonised standard, point-to-point,
radio, regulation, RLL, WLL
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Test conditions . 9
4.1 General . 9
4.1.1 Introduction. 9
4.1.2 Test conditions and configurations . 9
4.1.3 Emission tests . 10
4.1.4 Immunity tests . 10
4.2 Arrangements for test signals . 11
4.2.1 Arrangements for test signals at the input of the transmitter . 11
4.2.2 Arrangements for test signals at the output of the transmitter . 12
4.2.3 Arrangements for test signals at the input of the receiver . 12
4.2.4 Arrangements for test signals at the output of the receiver . 12
4.3 Exclusion bands . 12
4.3.1 Exclusion bands for receivers . 12
4.3.2 Exclusion bands for transmitters . 12
5 Performance assessment . 13
5.1 Equipment which can provide a communications link . 13
5.2 Ancillary equipment . 13
5.3 Equipment classification . 13
6 Performance criteria . 13
6.0 Introduction . 13
6.1 Performance criterion for Continuous phenomena applied to Transmitters (CT) and Receivers (CR) . 13
6.2 Performance criterion for Transient phenomena applied to Transmitters (TT) and Receivers (TR) . 13
6.3 Specific performance criteria . 13
6.3.1 Digital signal ports . 13
6.3.1.0 General performance criteria . 13
6.3.1.1 Performance criterion for continuous phenomena . 14
6.3.1.2 Performance criterion for transient phenomena . 14
6.3.2 Analogue voice frequency signal ports . 14
6.3.2.1 Performance criterion for continuous phenomena . 14
6.3.2.2 Performance criterion for transient phenomena . 14
6.3.3 Ethernet and packet-data interfaces . 14
6.3.3.0 Introduction . 14
6.3.3.1 Performance criterion for continuous phenomena . 14
6.3.3.2 Performance criterion for transient phenomena . 15
6.3.4 Service and maintenance interfaces . 15
6.3.5 Synchronization interfaces . 15
6.3.5.0 Introduction . 15
6.3.5.1 Performance criterion for continuous phenomena . 15
6.3.5.2 Performance criteria for transient phenomena . 15
6.3.6 Remote alarm interfaces . 15
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
6.3.6.1 Performance criterion for continuous phenomena . 15
6.3.6.2 Performance criterion for transient phenomena . 15
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 15
7 Applicability overview tables . 15
7.1 Emission . 15
7.1.1 General . 15
7.1.2 Special conditions . 16
7.2 Immunity . 16
7.2.1 General . 16
7.2.2 Special conditions . 17
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 18
Annex B (informative): Examples of Fixed Radio Link equipment within the scope of the
present document . 20
B.1 Fixed Radio Systems; Point-to-Point equipment; intended for operation in the frequency bands
from 1,3 GHz to 86 GHz . 20
B.2 Fixed Radio Systems; Point-to-Multipoint equipment; intended for operation in the frequency
band below 1 GHz and in frequency bands from 1 GHz to 40 GHz . 20
Annex C (informative): Change history . 21
History . 22
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Introduction
The structure of the ETSI EN 301 489 series has been changed for use under the RED from that used under the
R&TTED. The following text briefly explains this new format:
• The product specific part would contain in clause 7 two new tables similar to that currently in ETSI
EN 301 489-1 [1] clause 7.1 for emissions and clause 7.2 for immunity. These would inform the reader
whether the requirements, etc. are to be found in ETSI EN 301 489-1 [1] or further in the product specific part.
As an example; the assessment of a Wi-Fi router would use ETSI EN 301 489-17 [i.12] which would normatively
reference ETSI EN 301 489-1 [1] for certain aspects. Consequently:
• Changes to ETSI EN 301 489-1:
No references to product specific parts.
• Changes to product specific parts, e.g. the present document:
Two new tables, one for emissions in clause 7.1, and one for immunity in clause 7.2 that will point the reader
to the location of the requirements, i.e. ETSI EN 301 489-1 [1] or the present document.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
1 Scope
The present document specifies technical characteristics and methods of measurement for Analogue and Digital Fixed
Radio Links operating as fixed Point-to-Point, and Point-to-Multipoint systems as defined in annex B, including the
associated ancillary equipment.
NOTE 1: Technical specifications related to the antenna port of the radio equipment are not included in the present
document. Such technical specifications are found in the relevant product standards for the effective use
of the radio spectrum.
The processing and protection switch, (de)modulator, transmitter, receiver, RF filters, branching networks and feeders
are covered by the present document. The multiplexing and/or de-multiplexing elements are covered if they form part of
the transmitter, receiver and/or transceiver.
NOTE 2: The relationship between the present document and essential requirements of article 3.1b of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] Void.
[i.4] Void.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
[i.5] ETSI EN 302 217-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to
86 GHz; Harmonised Standard for access to radio spectrum".
[i.6] Void.
[i.7] ETSI EN 302 326-2: "Fixed Radio Systems; Multipoint Equipment and Antennas; Part 2:
Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive for
Digital Multipoint Radio Equipment".
[i.8] Void.
[i.9] Void.
[i.10] Void.
[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.12] ETSI EN 301 489-17: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised
Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 301 489-1 [1] and the following apply:
Base Station (BS): alternative name for Central Station
Central Station (CS): two units comprising of:
• the exchange unit, also called Central Controller Station (CCS) - (interface to the local switch); and
• the radio unit, also called Central Radio Station (CRS) - (central base band/radio transceiver)
NOTE: In some deployments the term Base Station is also used in place of Central Station. For the purposes of
the present standard either terms are assumed and are completely interchangeable.
operating frequency range: range(s) of radio frequencies covered by the Equipment Under Test (EUT) without any
change of units
Repeater Station (RS): radio repeater outstations with or without subscriber interfaces
Terminal station (TS): outstations with subscriber interfaces
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1 [1] and the following apply:
BER Bit Error Ratio
BS Base Station
CCS Central Controller Station
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
CR Continuous phenomena applied to Receivers
CRS Central Radio Station
CS Central Station
CT Continuous phenomena applied to Transmitters
RS Repeater Station
TR Transient phenomena applied to Receivers
TS Terminal Station
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General
4.1.1 Introduction
The test configuration and mode of operation shall represent the intended use and shall be recorded in the test report.
4.1.2 Test conditions and configurations
This clause defines the test conditions and configurations for the emission and immunity tests as follows:
• a transmitter shall, as a minimum, comprise the element between E' and A' of figure 1. Additionally the
transmitter may comprise any of the other elements from the transmitter chain shown in figure 1. If these
additional elements are part of the transmitter or system they shall also meet the requirements of the present
document;
Processing
Z'
G' F' E' A' B' C' D'
Tx RF
Branching
Multiplexing & Protection Modulator Transmitter Feeder
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B' to C') does not include a
hybrid.
NOTE 2: Points B' and C' may coincide, dependent on the equipment configuration.
Figure 1: Elements of a transmitter
• a receiver shall, as a minimum, comprise the element between A and E of figure 2. Additionally the receiver
may comprise any of the other elements from the receiver chain shown in figure 2. If these additional elements
are part of the receiver or system they shall also meet the requirements of the present document;
Processing
D C B Rx RF A E F G Z
Branching
Feeder Receiver Demodulator & Protection Demux
Network Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B to C) does not include a
hybrid.
NOTE 2: Points B and C may coincide, dependent on the equipment configuration.
Figure 2: Elements of a receiver
• a transceiver shall comprise as a minimum the elements E' to A' and A to E shown in figures 1 and 2, and
additionally it may comprise any combinations of the other elements. If these additional elements are part of
the transceiver they shall also meet the requirements of the present document;
ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
• the equipment shall be tested under conditions which are within the manufacturer's declared range of humidity,
temperature and supply voltage;
• the test configuration shall be as close to normal intended use as possible;
• if the equipment is part of a system, or can be connected to ancillary equipment, then it shall be acceptable to
test the equipment while connected to the minimum configuration of ancillary equipment necessary to exercise
the ports;
• ports which in normal operation are connected to ancillary or other equipment shall be either connected to
such equipment, or to a representative termination to simulate the input/output characteristics of the ancillary
or other equipment. Radio Frequency (RF) input/output ports shall be correctly terminated;
• if the equipment has a large number of ports, then a sufficient number shall be selected to simulate actual
operation conditions and to ensure that all the different types of termination are tested;
• ports which are not connected to cables during normal intended operation, e.g. service connectors,
programming connectors, temporary connectors, etc. shall not be connected to any cables for the purpose of
ElectroMagnetic Compatibility (EMC) testing. Where cables have to be connected to these ports, or
interconnecting cables have to be extended in length in order to exercise the EUT, precautions shall be taken to
ensure that the evaluation of the EUT is not affected by the addition or extension of these cables;
• the test conditions, test configuration and mode of operation shall be recorded in the test report.
4.1.3 Emission tests
For Point-to-Multipoint systems a communications link shall be established, which shall comprise of the Central Station
and a minimum of one Terminal Station. These stations are tested separately.
4.1.4 Immunity tests
The test configuration shall for transmitters be in accordance with the principle of figure 3, and for receivers it shall be
in accordance with the principle of figure 4, and for transceiver shall be in accordance with the principle of figure 5.
The measuring equipment shall be located outside the test environment. Adequate measures shall be taken to avoid any
effects of the unwanted signals on the measuring equipment.
Inside test environment Outside test environment
Input RF output
Monitoring
Transmitter
Receiver
Attenuator
equipment
Signal
source
Figure 3: Test configuration for transmitters
During immunity tests the transmitter shall be operated at its rated output power. The input to the transmitter shall be in
accordance with clause 4.2.1 (see figure 3). A communication link shall be established at the start of the test and be
maintained during the test.
ETSI
---------------------- Page: 10 ----------------------
11 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Inside test environment Outside test environment
Output
RF input
Signal
Receiver Attenuator
Transmitter
source
Monitoring
equipment
Figure 4: Test configuration for receivers
During immunity tests for receivers, the wanted RF input signal, coupled to the receiver, shall be in accordance with
clause 4.2.3 (see figure 4). A communication link shall be established at the start of the test and be maintained during
the test.
Inside test environment Outside test environment
RF output
Input
Monitoring
Receiver
Attenuator
Transmitter
equipment
RF input
Output
Signal
Receiver Attenuator Transmitter
source
Figure 5: Test configuration of transceivers
In the case of duplex transceivers where the transmitter and receiver cannot operate at the same radio frequency, the
wanted input signal, coupled to the receiver, shall be in accordance with clause 4.2.3. The transmitter shall be operated
at its rated output power, and with its input coupled to the output of the receiver (repeater mode) (see figure 5).
The same test configuration also applies where the transmitters and receivers operate at the same radio frequency.
The measurement shall be made in the mode of operation as required in this clause.
A communication link shall be established at the start of the test and be maintained during the test.
For the immunity test
...
SLOVENSKI STANDARD
oSIST prEN 301 489-4 V3.3.0:2020
01-junij-2020
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 4.
del: Posebni pogoji za fiksne radijske povezave in pomožno opremo -
Harmonizirani standard za elektromagnetno združljivost
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 4:
Specific conditions for fixed radio links and ancillary equipment - Harmonised Standard
for electromagnetic compatibility
Ta slovenski standard je istoveten z: ETSI EN 301 489-4 V3.3.0 (2020-03)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 301 489-4 V3.3.0:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
---------------------- Page: 2 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 4: Specific conditions for fixed radio links
and ancillary equipment;
Harmonised Standard for electromagnetic compatibility
---------------------- Page: 3 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
2 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Reference
REN/ERM-EMC-403
Keywords
EMC, FWA, harmonised standard, point-to-point,
radio, regulation, RLL, WLL
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
3 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Test conditions . 9
4.1 General . 9
4.1.1 Introduction. 9
4.1.2 Test conditions and configurations . 9
4.1.3 Emission tests . 10
4.1.4 Immunity tests . 10
4.2 Arrangements for test signals . 11
4.2.1 Arrangements for test signals at the input of the transmitter . 11
4.2.2 Arrangements for test signals at the output of the transmitter . 12
4.2.3 Arrangements for test signals at the input of the receiver . 12
4.2.4 Arrangements for test signals at the output of the receiver . 12
4.3 Exclusion bands . 12
4.3.1 Exclusion bands for receivers . 12
4.3.2 Exclusion bands for transmitters . 12
5 Performance assessment . 13
5.1 Equipment which can provide a communications link . 13
5.2 Ancillary equipment . 13
5.3 Equipment classification . 13
6 Performance criteria . 13
6.0 Introduction . 13
6.1 Performance criterion for Continuous phenomena applied to Transmitters (CT) and Receivers (CR) . 13
6.2 Performance criterion for Transient phenomena applied to Transmitters (TT) and Receivers (TR) . 13
6.3 Specific performance criteria . 13
6.3.1 Digital signal ports . 13
6.3.1.0 General performance criteria . 13
6.3.1.1 Performance criterion for continuous phenomena . 14
6.3.1.2 Performance criterion for transient phenomena . 14
6.3.2 Analogue voice frequency signal ports . 14
6.3.2.1 Performance criterion for continuous phenomena . 14
6.3.2.2 Performance criterion for transient phenomena . 14
6.3.3 Ethernet and packet-data interfaces . 14
6.3.3.0 Introduction . 14
6.3.3.1 Performance criterion for continuous phenomena . 14
6.3.3.2 Performance criterion for transient phenomena . 15
6.3.4 Service and maintenance interfaces . 15
6.3.5 Synchronization interfaces . 15
6.3.5.0 Introduction . 15
6.3.5.1 Performance criterion for continuous phenomena . 15
6.3.5.2 Performance criteria for transient phenomena . 15
6.3.6 Remote alarm interfaces . 15
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
4 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
6.3.6.1 Performance criterion for continuous phenomena . 15
6.3.6.2 Performance criterion for transient phenomena . 15
6.4 Performance criteria for ancillary equipment tested on a stand alone basis . 15
7 Applicability overview tables . 15
7.1 Emission . 15
7.1.1 General . 15
7.1.2 Special conditions . 16
7.2 Immunity . 16
7.2.1 General . 16
7.2.2 Special conditions . 17
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 18
Annex B (informative): Examples of Fixed Radio Link equipment within the scope of the
present document . 20
B.1 Fixed Radio Systems; Point-to-Point equipment; intended for operation in the frequency bands
from 1,3 GHz to 86 GHz . 20
B.2 Fixed Radio Systems; Point-to-Multipoint equipment; intended for operation in the frequency
band below 1 GHz and in frequency bands from 1 GHz to 40 GHz . 20
Annex C (informative): Change history . 21
History . 22
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
5 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
6 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
Introduction
The structure of the ETSI EN 301 489 series has been changed for use under the RED from that used under the
R&TTED. The following text briefly explains this new format:
• The product specific part would contain in clause 7 two new tables similar to that currently in ETSI
EN 301 489-1 [1] clause 7.1 for emissions and clause 7.2 for immunity. These would inform the reader
whether the requirements, etc. are to be found in ETSI EN 301 489-1 [1] or further in the product specific part.
As an example; the assessment of a Wi-Fi router would use ETSI EN 301 489-17 [i.12] which would normatively
reference ETSI EN 301 489-1 [1] for certain aspects. Consequently:
• Changes to ETSI EN 301 489-1:
No references to product specific parts.
• Changes to product specific parts, e.g. the present document:
Two new tables, one for emissions in clause 7.1, and one for immunity in clause 7.2 that will point the reader
to the location of the requirements, i.e. ETSI EN 301 489-1 [1] or the present document.
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
7 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
1 Scope
The present document specifies technical characteristics and methods of measurement for Analogue and Digital Fixed
Radio Links operating as fixed Point-to-Point, and Point-to-Multipoint systems as defined in annex B, including the
associated ancillary equipment.
NOTE 1: Technical specifications related to the antenna port of the radio equipment are not included in the present
document. Such technical specifications are found in the relevant product standards for the effective use
of the radio spectrum.
The processing and protection switch, (de)modulator, transmitter, receiver, RF filters, branching networks and feeders
are covered by the present document. The multiplexing and/or de-multiplexing elements are covered if they form part of
the transmitter, receiver and/or transceiver.
NOTE 2: The relationship between the present document and essential requirements of article 3.1b of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] Void.
[i.4] Void.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
8 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
[i.5] ETSI EN 302 217-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to
86 GHz; Harmonised Standard for access to radio spectrum".
[i.6] Void.
[i.7] ETSI EN 302 326-2: "Fixed Radio Systems; Multipoint Equipment and Antennas; Part 2:
Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive for
Digital Multipoint Radio Equipment".
[i.8] Void.
[i.9] Void.
[i.10] Void.
[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.12] ETSI EN 301 489-17: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised
Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 301 489-1 [1] and the following apply:
Base Station (BS): alternative name for Central Station
Central Station (CS): two units comprising of:
• the exchange unit, also called Central Controller Station (CCS) - (interface to the local switch); and
• the radio unit, also called Central Radio Station (CRS) - (central base band/radio transceiver)
NOTE: In some deployments the term Base Station is also used in place of Central Station. For the purposes of
the present standard either terms are assumed and are completely interchangeable.
operating frequency range: range(s) of radio frequencies covered by the Equipment Under Test (EUT) without any
change of units
Repeater Station (RS): radio repeater outstations with or without subscriber interfaces
Terminal station (TS): outstations with subscriber interfaces
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1 [1] and the following apply:
BER Bit Error Ratio
BS Base Station
CCS Central Controller Station
ETSI
---------------------- Page: 10 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
9 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
CR Continuous phenomena applied to Receivers
CRS Central Radio Station
CS Central Station
CT Continuous phenomena applied to Transmitters
RS Repeater Station
TR Transient phenomena applied to Receivers
TS Terminal Station
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General
4.1.1 Introduction
The test configuration and mode of operation shall represent the intended use and shall be recorded in the test report.
4.1.2 Test conditions and configurations
This clause defines the test conditions and configurations for the emission and immunity tests as follows:
• a transmitter shall, as a minimum, comprise the element between E' and A' of figure 1. Additionally the
transmitter may comprise any of the other elements from the transmitter chain shown in figure 1. If these
additional elements are part of the transmitter or system they shall also meet the requirements of the present
document;
Processing
Z'
G' F' E' A' B' C' D'
Tx RF
Branching
Multiplexing & Protection Modulator Transmitter Feeder
Network
Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B' to C') does not include a
hybrid.
NOTE 2: Points B' and C' may coincide, dependent on the equipment configuration.
Figure 1: Elements of a transmitter
• a receiver shall, as a minimum, comprise the element between A and E of figure 2. Additionally the receiver
may comprise any of the other elements from the receiver chain shown in figure 2. If these additional elements
are part of the receiver or system they shall also meet the requirements of the present document;
Processing
D C B Rx RF A E F G Z
Branching
Feeder Receiver Demodulator & Protection Demux
Network Filter
Switch
NOTE 1: For the purposes of defining the reference points, the branching network (B to C) does not include a
hybrid.
NOTE 2: Points B and C may coincide, dependent on the equipment configuration.
Figure 2: Elements of a receiver
• a transceiver shall comprise as a minimum the elements E' to A' and A to E shown in figures 1 and 2, and
additionally it may comprise any combinations of the other elements. If these additional elements are part of
the transceiver they shall also meet the requirements of the present document;
ETSI
---------------------- Page: 11 ----------------------
oSIST prEN 301 489-4 V3.3.0:2020
10 Draft ETSI EN 301 489-4 V3.3.0 (2020-03)
• the equipment shall be tested under conditions which are within the manufacturer's declared range of humidity,
temperature and supply voltage;
• the test configuration shall be as close to normal intended use as possible;
• if the equipment is part of a system, or can be connected to ancillary equipment, then it shall be acceptable to
test the equipment while connected to the minimum configuration of ancillary equipment necessary to exercise
the ports;
• ports which in normal operation are connected to ancillary or other equipment shall be either connected to
such equipment, or to a representative termination to simulate the input/output characteristics of the ancillary
or other equipment. Radio Frequency (RF) input/output ports shall be correctly terminated;
• if the equipment has a large number of ports, then a sufficient number shall be selected to simulate actual
operation conditions and to ensure that all the different types of termination are tested;
• ports which are not connected to cables during normal intended operation, e.g. service connectors,
programming connectors, temporary connectors, etc. shall not be connected to any cables for the purpose of
ElectroMagnetic Compatibility (EMC) testing. Where cables have to be connected to these ports, or
interconnecting cables have to be extended in length in order to exercise the EUT, precautions shall be taken to
ensure that the evaluation of the EUT is not affected by the addition or extension of these cables;
• the test conditions, test configuration and mode of operation shall be recorded in the test report.
4.1.3 Emission tests
For Point-to-Multipoint systems a communications link shall be established, which shall comprise of the Central Station
and a minimum of one Terminal Station. These stations are tested separately.
4.1.4 Immunity tests
The test configuration shall for transmitters be in accordance with the principle of figure 3, and for receivers it shall be
in accordance with the principle of figure 4, and for transceiver shall be in accordance with the principle of figure 5.
The measuring equipment shall be located outside the test environment. Adequate measures shall be taken to avoid any
effects of the unwanted signals on the measuring equipment.
Inside test environment Outside test environment
Input RF output
Monitoring
Transmitter
Receiver
Attenuator
equipment
Signal
source
Figure 3: Test configuration for transmitters
During immunity tests the transmitter shall be operated at its rated output power. The input to the transmitter shall be in
accordance with clause 4.2.1 (see figure 3). A communication link shall be established at the start of the test and be
maintained during the test.
ETSI
---------------------- Page: 12 ----------------------
oSIST prEN 301 489-4 V3.3.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.