ETSI EN 300 113 V3.1.1 (2020-06)
Land Mobile Service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector
Land Mobile Service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector
REN/ERM-TGDMR-377
Storitev kopenskih mobilnih komunikacij - Radijska oprema za prenos podatkov (oziroma govora), ki uporablja modulacijo s konstantno ali nekonstantno ovojnico in ima antenski priključek
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 300 113 V3.1.1:2020
01-september-2020
Storitev kopenskih mobilnih komunikacij - Radijska oprema za prenos podatkov
(oziroma govora), ki uporablja modulacijo s konstantno ali nekonstantno ovojnico
in ima antenski priključek
Land Mobile Service - Radio equipment intended for the transmission of data (and/or
speech) using constant or non-constant envelope modulation and having an antenna
connector
Ta slovenski standard je istoveten z: ETSI EN 300 113 V3.1.1 (2020-06)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
SIST EN 300 113 V3.1.1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 113 V3.1.1:2020
---------------------- Page: 2 ----------------------
SIST EN 300 113 V3.1.1:2020
ETSI EN 300 113 V3.1.1 (2020-06)
EUROPEAN STANDARD
Land Mobile Service;
Radio equipment intended for the transmission of data
(and/or speech) using constant or non-constant
envelope modulation and having an antenna connector
---------------------- Page: 3 ----------------------
SIST EN 300 113 V3.1.1:2020
2 ETSI EN 300 113 V3.1.1 (2020-06)
Reference
REN/ERM-TGDMR-377
Keywords
antenna, data, mobile, PMR, radio, regulation,
speech, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 113 V3.1.1:2020
3 ETSI EN 300 113 V3.1.1 (2020-06)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 10
3.1 Terms . 10
3.2 Symbols . 12
3.3 Abbreviations . 12
4 General and operational requirements . 13
4.1 General . 13
4.1.1 Environmental profile . 13
4.1.2 Choice of model for testing . 13
4.2 Mechanical and electrical design . 13
4.2.1 General . 13
4.2.2 Controls . 13
4.2.3 Transmitter shut-off facility . 14
4.3 Testing using bit streams or messages . 14
4.4 Measuring continuous mode equipment . 14
4.5 Measuring discontinuous mode equipment . 14
4.6 Constant and non-constant envelope modulation . 14
4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 14
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 15
5.3 Normal test conditions . 16
5.3.1 Normal temperature and humidity . 16
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 16
5.4.1 Extreme temperatures . 16
5.4.2 Extreme test source voltages . 17
5.4.2.1 Mains voltage . 17
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 17
5.4.2.3 Power sources using other types of batteries . 17
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 17
5.5.0 Thermal balance . 17
5.5.1 Procedure for equipment designed for continuous transmission. 17
5.5.2 Procedure for equipment designed for intermittent transmission . 18
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 18
6 General conditions of measurement . 18
6.1 Arrangements for test signals applied to the receiver input . 18
6.2 Receiver mute or squelch facility . 18
6.3 Normal test signals (wanted and unwanted signals) . 18
6.3.1 Equipment measured as constant envelope angle modulation equipment . 18
6.3.2 Equipment measured as non-constant envelope modulation equipment . 19
6.4 Encoder for receiver measurements . 20
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 113 V3.1.1:2020
4 ETSI EN 300 113 V3.1.1 (2020-06)
6.5 Transceiver data interface. 20
6.6 Impedance . 20
6.7 Artificial antenna . 20
6.8 Tests of equipment with a duplex filter . 20
6.9 Facilities for access . 21
6.9.1 Analogue access . 21
6.9.2 Test points for bit stream measurements. 21
6.9.3 Coupling arrangements . 21
6.9.3.0 General . 21
6.9.3.1 Arrangements for measurements with continuous bit streams . 21
6.9.3.2 Arrangements for measurements with messages . 21
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 22
6.11 Modes of operation of the transmitter for constant envelope equipment . 22
6.12 Multi-rate equipment . 22
7 Technical characteristics of the transmitter . 22
7.1 Frequency error . 22
7.1.0 General . 22
7.1.1 Definition . 22
7.1.2 Method of measurement . 22
7.1.3 Limits . 23
7.2 Transmitter power (conducted) . 23
7.2.1 Definitions . 23
7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 23
7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 23
7.2.2 Method of measurement . 24
7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 24
7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 24
7.2.3 Limits . 24
7.3 Maximum Effective radiated power . 25
7.3.1 Definition . 25
7.3.1.0 General . 25
7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 25
7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 25
7.3.2 Methods of measurement . 25
7.3.2.0 General . 25
7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 27
7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 28
7.3.3 Limits . 29
7.4 Adjacent and alternate channel power . 30
7.4.1 Definition . 30
7.4.2 Method of measurement . 30
7.4.3 Limits . 31
7.5 Unwanted emissions in the spurious domain. 32
7.5.1 Definition . 32
7.5.2 Method of measuring the power level . 32
7.5.2.0 General . 32
7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 33
7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 33
7.5.3 Method of measuring the effective radiated power . 33
7.5.3.0 General . 33
7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 34
7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 34
7.5.4 Limits . 36
7.6 Intermodulation attenuation. 37
7.6.1 Definition . 37
7.6.2 Method of measurement . 37
7.6.3 Limits . 38
7.7 Transmitter attack time . 38
7.7.1 Definition . 38
7.7.2 Method of measurement . 39
7.7.3 Limit . 39
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 113 V3.1.1:2020
5 ETSI EN 300 113 V3.1.1 (2020-06)
7.8 Transmitter release time . 39
7.8.1 Definition . 39
7.8.2 Method of measurement . 40
7.8.3 Limits . 40
7.9 Transient behaviour of the transmitter . 40
7.9.1 Definitions . 40
7.9.2 Timings, frequencies and powers . 41
7.9.3 Methods of measurement . 45
7.9.3.0 General . 45
7.9.3.1 Time domain measurements of power and frequency . 45
7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 46
7.9.3.3 Adjacent channel transient power measurements . 46
7.9.3.3.1 Definition. 46
7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 46
7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 47
7.9.3.3.4 Alternative measurement method using a spectrum analyser . 48
7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 49
7.9.4 Limits . 49
7.9.4.0 General . 49
7.9.4.1 Time domain analysis of power and frequency for constant envelope transmissions . 50
7.9.4.2 Adjacent and alternate channel transient power . 50
7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 50
7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 50
8 Technical characteristics of the receiver . 51
8.1 Maximum usable sensitivity (conducted) . 51
8.1.1 Definition . 51
8.1.2 Method of measurement . 51
8.1.2.1 Method of measurement with continuous bit streams . 51
8.1.2.2 Method of measurement with messages . 52
8.1.2.3 Method of measurement with packets . 52
8.1.3 Limits . 53
8.2 Average usable sensitivity (field strength) . 53
8.2.1 Definition . 53
8.2.2 Method of measurement . 53
8.2.3 Limits . 54
8.3 Level of the wanted signal for the degradation measurements . 55
8.4 Error behaviour at high input levels . 55
8.4.1 Definition . 55
8.4.2 Method of measurement . 56
8.4.2.1 Method of measurement with continuous bit streams . 56
8.4.2.2 Method of measurement with messages . 56
8.4.2.3 Method of measurement with packets . 57
8.4.3 Limits . 57
8.5 Co-channel rejection. 57
8.5.1 Definition . 57
8.5.2 Method of measurement . 57
8.5.2.1 Method of measurement with continuous bit streams . 57
8.5.2.2 Method of measurement with messages . 58
8.5.2.3 Method of measurement with packets . 59
8.5.3 Limits . 60
8.6 Adjacent channel selectivity . 60
8.6.1 Definition . 60
8.6.2 Method of measurement . 61
8.6.2.1 Method of measurement with continuous bit streams . 61
8.6.2.2 Method of measurement with messages . 62
8.6.2.3 Method of measurement with packets .
...
ETSI EN 300 113 V3.1.1 (2020-06)
EUROPEAN STANDARD
Land Mobile Service;
Radio equipment intended for the transmission of data
(and/or speech) using constant or non-constant
envelope modulation and having an antenna connector
---------------------- Page: 1 ----------------------
2 ETSI EN 300 113 V3.1.1 (2020-06)
Reference
REN/ERM-TGDMR-377
Keywords
antenna, data, mobile, PMR, radio, regulation,
speech, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 113 V3.1.1 (2020-06)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 10
3.1 Terms . 10
3.2 Symbols . 12
3.3 Abbreviations . 12
4 General and operational requirements . 13
4.1 General . 13
4.1.1 Environmental profile . 13
4.1.2 Choice of model for testing . 13
4.2 Mechanical and electrical design . 13
4.2.1 General . 13
4.2.2 Controls . 13
4.2.3 Transmitter shut-off facility . 14
4.3 Testing using bit streams or messages . 14
4.4 Measuring continuous mode equipment . 14
4.5 Measuring discontinuous mode equipment . 14
4.6 Constant and non-constant envelope modulation . 14
4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 14
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 15
5.3 Normal test conditions . 16
5.3.1 Normal temperature and humidity . 16
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 16
5.4.1 Extreme temperatures . 16
5.4.2 Extreme test source voltages . 17
5.4.2.1 Mains voltage . 17
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 17
5.4.2.3 Power sources using other types of batteries . 17
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 17
5.5.0 Thermal balance . 17
5.5.1 Procedure for equipment designed for continuous transmission. 17
5.5.2 Procedure for equipment designed for intermittent transmission . 18
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 18
6 General conditions of measurement . 18
6.1 Arrangements for test signals applied to the receiver input . 18
6.2 Receiver mute or squelch facility . 18
6.3 Normal test signals (wanted and unwanted signals) . 18
6.3.1 Equipment measured as constant envelope angle modulation equipment . 18
6.3.2 Equipment measured as non-constant envelope modulation equipment . 19
6.4 Encoder for receiver measurements . 20
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 113 V3.1.1 (2020-06)
6.5 Transceiver data interface. 20
6.6 Impedance . 20
6.7 Artificial antenna . 20
6.8 Tests of equipment with a duplex filter . 20
6.9 Facilities for access . 21
6.9.1 Analogue access . 21
6.9.2 Test points for bit stream measurements. 21
6.9.3 Coupling arrangements . 21
6.9.3.0 General . 21
6.9.3.1 Arrangements for measurements with continuous bit streams . 21
6.9.3.2 Arrangements for measurements with messages . 21
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 22
6.11 Modes of operation of the transmitter for constant envelope equipment . 22
6.12 Multi-rate equipment . 22
7 Technical characteristics of the transmitter . 22
7.1 Frequency error . 22
7.1.0 General . 22
7.1.1 Definition . 22
7.1.2 Method of measurement . 22
7.1.3 Limits . 23
7.2 Transmitter power (conducted) . 23
7.2.1 Definitions . 23
7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 23
7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 23
7.2.2 Method of measurement . 24
7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 24
7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 24
7.2.3 Limits . 24
7.3 Maximum Effective radiated power . 25
7.3.1 Definition . 25
7.3.1.0 General . 25
7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 25
7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 25
7.3.2 Methods of measurement . 25
7.3.2.0 General . 25
7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 27
7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 28
7.3.3 Limits . 29
7.4 Adjacent and alternate channel power . 30
7.4.1 Definition . 30
7.4.2 Method of measurement . 30
7.4.3 Limits . 31
7.5 Unwanted emissions in the spurious domain. 32
7.5.1 Definition . 32
7.5.2 Method of measuring the power level . 32
7.5.2.0 General . 32
7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 33
7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 33
7.5.3 Method of measuring the effective radiated power . 33
7.5.3.0 General . 33
7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 34
7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 34
7.5.4 Limits . 36
7.6 Intermodulation attenuation. 37
7.6.1 Definition . 37
7.6.2 Method of measurement . 37
7.6.3 Limits . 38
7.7 Transmitter attack time . 38
7.7.1 Definition . 38
7.7.2 Method of measurement . 39
7.7.3 Limit . 39
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 113 V3.1.1 (2020-06)
7.8 Transmitter release time . 39
7.8.1 Definition . 39
7.8.2 Method of measurement . 40
7.8.3 Limits . 40
7.9 Transient behaviour of the transmitter . 40
7.9.1 Definitions . 40
7.9.2 Timings, frequencies and powers . 41
7.9.3 Methods of measurement . 45
7.9.3.0 General . 45
7.9.3.1 Time domain measurements of power and frequency . 45
7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 46
7.9.3.3 Adjacent channel transient power measurements . 46
7.9.3.3.1 Definition. 46
7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 46
7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 47
7.9.3.3.4 Alternative measurement method using a spectrum analyser . 48
7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 49
7.9.4 Limits . 49
7.9.4.0 General . 49
7.9.4.1 Time domain analysis of power and frequency for constant envelope transmissions . 50
7.9.4.2 Adjacent and alternate channel transient power . 50
7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 50
7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 50
8 Technical characteristics of the receiver . 51
8.1 Maximum usable sensitivity (conducted) . 51
8.1.1 Definition . 51
8.1.2 Method of measurement . 51
8.1.2.1 Method of measurement with continuous bit streams . 51
8.1.2.2 Method of measurement with messages . 52
8.1.2.3 Method of measurement with packets . 52
8.1.3 Limits . 53
8.2 Average usable sensitivity (field strength) . 53
8.2.1 Definition . 53
8.2.2 Method of measurement . 53
8.2.3 Limits . 54
8.3 Level of the wanted signal for the degradation measurements . 55
8.4 Error behaviour at high input levels . 55
8.4.1 Definition . 55
8.4.2 Method of measurement . 56
8.4.2.1 Method of measurement with continuous bit streams . 56
8.4.2.2 Method of measurement with messages . 56
8.4.2.3 Method of measurement with packets . 57
8.4.3 Limits . 57
8.5 Co-channel rejection. 57
8.5.1 Definition . 57
8.5.2 Method of measurement . 57
8.5.2.1 Method of measurement with continuous bit streams . 57
8.5.2.2 Method of measurement with messages . 58
8.5.2.3 Method of measurement with packets . 59
8.5.3 Limits . 60
8.6 Adjacent channel selectivity . 60
8.6.1 Definition . 60
8.6.2 Method of measurement . 61
8.6.2.1 Method of measurement with continuous bit streams . 61
8.6.2.2 Method of measurement with messages . 62
8.6.2.3 Method of measurement with packets . 63
8.6.3 Limits . 64
8.7 Spurious response rejection . 64
8.7.1 Definition . 64
8.7.2 Introduction to the method of measurement . 64
8.7.3 Method of search over the "limited frequency range" . 65
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 113 V3.1.1 (2020-06)
8.7.4 Method of measurement with continuous bit streams . 66
...
Draft ETSI EN 300 113 V2.3.0 (2020-03)
EUROPEAN STANDARD
Land Mobile Service;
Radio equipment intended for the transmission of data
(and/or speech) using constant or non-constant
envelope modulation and having an antenna connector
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 113 V2.3.0 (2020-03)
Reference
REN/ERM-TGDMR-377
Keywords
antenna, data, mobile, PMR, radio, regulation,
speech, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 113 V2.3.0 (2020-03)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 10
3.1 Terms . 10
3.2 Symbols . 12
3.3 Abbreviations . 12
4 General and operational requirements . 13
4.1 General . 13
4.1.1 Environmental profile . 13
4.1.2 Choice of model for testing . 13
4.2 Mechanical and electrical design . 13
4.2.1 General . 13
4.2.2 Controls . 13
4.2.3 Transmitter shut-off facility . 14
4.3 Testing using bit streams or messages . 14
4.4 Measuring continuous mode equipment . 14
4.5 Measuring discontinuous mode equipment . 14
4.6 Constant and non-constant envelope modulation . 14
4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 14
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 15
5.3 Normal test conditions . 16
5.3.1 Normal temperature and humidity . 16
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 16
5.4.1 Extreme temperatures . 16
5.4.2 Extreme test source voltages . 17
5.4.2.1 Mains voltage . 17
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 17
5.4.2.3 Power sources using other types of batteries . 17
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 17
5.5.0 Thermal balance . 17
5.5.1 Procedure for equipment designed for continuous transmission. 17
5.5.2 Procedure for equipment designed for intermittent transmission . 18
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 18
6 General conditions of measurement . 18
6.1 Arrangements for test signals applied to the receiver input . 18
6.2 Receiver mute or squelch facility . 18
6.3 Normal test signals (wanted and unwanted signals) . 18
6.3.1 Equipment measured as constant envelope angle modulation equipment . 18
6.3.2 Equipment measured as non-constant envelope modulation equipment . 19
6.4 Encoder for receiver measurements . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 113 V2.3.0 (2020-03)
6.5 Transceiver data interface. 20
6.6 Impedance . 20
6.7 Artificial antenna . 20
6.8 Tests of equipment with a duplex filter . 20
6.9 Facilities for access . 21
6.9.1 Analogue access . 21
6.9.2 Test points for bit stream measurements. 21
6.9.3 Coupling arrangements . 21
6.9.3.0 General . 21
6.9.3.1 Arrangements for measurements with continuous bit streams . 21
6.9.3.2 Arrangements for measurements with messages . 21
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 22
6.11 Modes of operation of the transmitter for constant envelope equipment . 22
6.12 Multi-rate equipment . 22
7 Technical characteristics of the transmitter . 22
7.1 Frequency error . 22
7.1.0 General . 22
7.1.1 Definition . 22
7.1.2 Method of measurement . 22
7.1.3 Limits . 23
7.2 Transmitter power (conducted) . 23
7.2.1 Definitions . 23
7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 23
7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 23
7.2.2 Method of measurement . 24
7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 24
7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 24
7.2.3 Limits . 24
7.3 Maximum Effective radiated power . 25
7.3.1 Definition . 25
7.3.1.0 General . 25
7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 25
7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 25
7.3.2 Methods of measurement . 25
7.3.2.0 General . 25
7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 27
7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 28
7.3.3 Limits . 29
7.4 Adjacent and alternate channel power . 30
7.4.1 Definition . 30
7.4.2 Method of measurement . 30
7.4.3 Limits . 31
7.5 Unwanted emissions in the spurious domain. 32
7.5.1 Definition . 32
7.5.2 Method of measuring the power level . 32
7.5.2.0 General . 32
7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 33
7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 33
7.5.3 Method of measuring the effective radiated power . 33
7.5.3.0 General . 33
7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 34
7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 34
7.5.4 Limits . 36
7.6 Intermodulation attenuation. 37
7.6.1 Definition . 37
7.6.2 Method of measurement . 37
7.6.3 Limits . 38
7.7 Transmitter attack time . 38
7.7.1 Definition . 38
7.7.2 Method of measurement . 39
7.7.3 Limit . 39
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 113 V2.3.0 (2020-03)
7.8 Transmitter release time . 39
7.8.1 Definition . 39
7.8.2 Method of measurement . 40
7.8.3 Limits . 40
7.9 Transient behaviour of the transmitter . 40
7.9.1 Definitions . 40
7.9.2 Timings, frequencies and powers . 41
7.9.3 Methods of measurement . 45
7.9.3.0 General . 45
7.9.3.1 Time domain measurements of power and frequency . 45
7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 46
7.9.3.3 Adjacent channel transient power measurements . 46
7.9.3.3.1 Definition. 46
7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 46
7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 47
7.9.3.3.4 Alternative measurement method using a spectrum analyser . 48
7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 49
7.9.4 Limits . 49
7.9.4.0 General . 49
7.9.4.1 Time domain analysis of power and frequency for constant envelope transmissions . 50
7.9.4.2 Adjacent and alternate channel transient power . 50
7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 50
7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 50
8 Technical characteristics of the receiver . 51
8.1 Maximum usable sensitivity (conducted) . 51
8.1.1 Definition . 51
8.1.2 Method of measurement . 51
8.1.2.1 Method of measurement with continuous bit streams . 51
8.1.2.2 Method of measurement with messages . 52
8.1.2.3 Method of measurement with packets . 52
8.1.3 Limits . 53
8.2 Average usable sensitivity (field strength) . 53
8.2.1 Definition . 53
8.2.2 Method of measurement . 53
8.2.3 Limits . 54
8.3 Level of the wanted signal for the degradation measurements . 55
8.4 Error behaviour at high input levels . 55
8.4.1 Definition . 55
8.4.2 Method of measurement . 56
8.4.2.1 Method of measurement with continuous bit streams . 56
8.4.2.2 Method of measurement with messages . 56
8.4.2.3 Method of measurement with packets . 57
8.4.3 Limits . 57
8.5 Co-channel rejection. 57
8.5.1 Definition . 57
8.5.2 Method of measurement . 57
8.5.2.1 Method of measurement with continuous bit streams . 57
8.5.2.2 Method of measurement with messages . 58
8.5.2.3 Method of measurement with packets . 59
8.5.3 Limits . 60
8.6 Adjacent channel selectivity . 60
8.6.1 Definition . 60
8.6.2 Method of measurement . 61
8.6.2.1 Method of measurement with continuous bit streams . 61
8.6.2.2 Method of measurement with messages . 62
8.6.2.3 Method of measurement with packets . 63
8.6.3 Limits . 64
8.7 Spurious response rejection . 64
8.7.1 Definition . 64
8.7.2 Introduction to the method of measurement . 64
8.7.3 Method of search over the "limited frequency range" . 65
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 113 V2.3.0 (2020-03)
8.7.4 Method of measurement with continuous bit streams .
...
SLOVENSKI STANDARD
oSIST prEN 300 113 V2.3.0:2020
01-junij-2020
Storitev kopenskih mobilnih komunikacij - Radijska oprema za prenos podatkov
(oziroma govora), ki uporablja modulacijo s konstantno ali nekonstantno ovojnico
in ima antenski priključek
Land Mobile Service - Radio equipment intended for the transmission of data (and/or
speech) using constant or non-constant envelope modulation and having an antenna
connector
Ta slovenski standard je istoveten z: ETSI EN 300 113 V2.3.0 (2020-03)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
oSIST prEN 300 113 V2.3.0:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 300 113 V2.3.0:2020
---------------------- Page: 2 ----------------------
oSIST prEN 300 113 V2.3.0:2020
Draft ETSI EN 300 113 V2.3.0 (2020-03)
EUROPEAN STANDARD
Land Mobile Service;
Radio equipment intended for the transmission of data
(and/or speech) using constant or non-constant
envelope modulation and having an antenna connector
---------------------- Page: 3 ----------------------
oSIST prEN 300 113 V2.3.0:2020
2 Draft ETSI EN 300 113 V2.3.0 (2020-03)
Reference
REN/ERM-TGDMR-377
Keywords
antenna, data, mobile, PMR, radio, regulation,
speech, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 113 V2.3.0:2020
3 Draft ETSI EN 300 113 V2.3.0 (2020-03)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 10
3.1 Terms . 10
3.2 Symbols . 12
3.3 Abbreviations . 12
4 General and operational requirements . 13
4.1 General . 13
4.1.1 Environmental profile . 13
4.1.2 Choice of model for testing . 13
4.2 Mechanical and electrical design . 13
4.2.1 General . 13
4.2.2 Controls . 13
4.2.3 Transmitter shut-off facility . 14
4.3 Testing using bit streams or messages . 14
4.4 Measuring continuous mode equipment . 14
4.5 Measuring discontinuous mode equipment . 14
4.6 Constant and non-constant envelope modulation . 14
4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 14
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 15
5.3 Normal test conditions . 16
5.3.1 Normal temperature and humidity . 16
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 16
5.4.1 Extreme temperatures . 16
5.4.2 Extreme test source voltages . 17
5.4.2.1 Mains voltage . 17
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 17
5.4.2.3 Power sources using other types of batteries . 17
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 17
5.5.0 Thermal balance . 17
5.5.1 Procedure for equipment designed for continuous transmission. 17
5.5.2 Procedure for equipment designed for intermittent transmission . 18
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 18
6 General conditions of measurement . 18
6.1 Arrangements for test signals applied to the receiver input . 18
6.2 Receiver mute or squelch facility . 18
6.3 Normal test signals (wanted and unwanted signals) . 18
6.3.1 Equipment measured as constant envelope angle modulation equipment . 18
6.3.2 Equipment measured as non-constant envelope modulation equipment . 19
6.4 Encoder for receiver measurements . 20
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 113 V2.3.0:2020
4 Draft ETSI EN 300 113 V2.3.0 (2020-03)
6.5 Transceiver data interface. 20
6.6 Impedance . 20
6.7 Artificial antenna . 20
6.8 Tests of equipment with a duplex filter . 20
6.9 Facilities for access . 21
6.9.1 Analogue access . 21
6.9.2 Test points for bit stream measurements. 21
6.9.3 Coupling arrangements . 21
6.9.3.0 General . 21
6.9.3.1 Arrangements for measurements with continuous bit streams . 21
6.9.3.2 Arrangements for measurements with messages . 21
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 22
6.11 Modes of operation of the transmitter for constant envelope equipment . 22
6.12 Multi-rate equipment . 22
7 Technical characteristics of the transmitter . 22
7.1 Frequency error . 22
7.1.0 General . 22
7.1.1 Definition . 22
7.1.2 Method of measurement . 22
7.1.3 Limits . 23
7.2 Transmitter power (conducted) . 23
7.2.1 Definitions . 23
7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 23
7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 23
7.2.2 Method of measurement . 24
7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 24
7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 24
7.2.3 Limits . 24
7.3 Maximum Effective radiated power . 25
7.3.1 Definition . 25
7.3.1.0 General . 25
7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 25
7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 25
7.3.2 Methods of measurement . 25
7.3.2.0 General . 25
7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 27
7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 28
7.3.3 Limits . 29
7.4 Adjacent and alternate channel power . 30
7.4.1 Definition . 30
7.4.2 Method of measurement . 30
7.4.3 Limits . 31
7.5 Unwanted emissions in the spurious domain. 32
7.5.1 Definition . 32
7.5.2 Method of measuring the power level . 32
7.5.2.0 General . 32
7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 33
7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 33
7.5.3 Method of measuring the effective radiated power . 33
7.5.3.0 General . 33
7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 34
7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 34
7.5.4 Limits . 36
7.6 Intermodulation attenuation. 37
7.6.1 Definition . 37
7.6.2 Method of measurement . 37
7.6.3 Limits . 38
7.7 Transmitter attack time . 38
7.7.1 Definition . 38
7.7.2 Method of measurement . 39
7.7.3 Limit . 39
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 113 V2.3.0:2020
5 Draft ETSI EN 300 113 V2.3.0 (2020-03)
7.8 Transmitter release time . 39
7.8.1 Definition . 39
7.8.2 Method of measurement . 40
7.8.3 Limits . 40
7.9 Transient behaviour of the transmitter . 40
7.9.1 Definitions . 40
7.9.2 Timings, frequencies and powers . 41
7.9.3 Methods of measurement . 45
7.9.3.0 General . 45
7.9.3.1 Time domain measurements of power and frequency . 45
7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 46
7.9.3.3 Adjacent channel transient power measurements . 46
7.9.3.3.1 Definition. 46
7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 46
7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 47
7.9.3.3.4 Alternative measurement method using a spectrum analyser . 48
7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 49
7.9.4 Limits . 49
7.9.4.0 General . 49
7.9.4.1 Time domain analysis of power and frequency for constant envelope transmissions . 50
7.9.4.2 Adjacent and alternate channel transient power . 50
7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 50
7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 50
8 Technical characteristics of the receiver . 51
8.1 Maximum usable sensitivity (conducted) . 51
8.1.1 Definition . 51
8.1.2 Method of measurement . 51
8.1.2.1 Method of measurement with continuous bit streams . 51
8.1.2.2 Method of measurement with messages . 52
8.1.2.3 Method of measurement with packets . 52
8.1.3 Limits . 53
8.2 Average usable sensitivity (field strength) . 53
8.2.1 Definition . 53
8.2.2 Method of measurement . 53
8.2.3 Limits . 54
8.3 Level of the wanted signal for the degradation measurements . 55
8.4 Error behaviour at high input levels . 55
8.4.1 Definition . 55
8.4.2 Method of measurement . 56
8.4.2.1 Method of measurement with continuous bit streams . 56
8.4.2.2 Method of measurement with messages . 56
8.4.2.3 Method of measurement with packets . 57
8.4.3 Limits . 57
8.5 Co-channel rejection. 57
8.5.1 Definition . 57
8.5.2 Method of measurement . 57
8.5.2.1 Method of measurement with continuous bit streams . 57
8.5.2.2 Method of measurement with messages . 58
8.5.2.3 Method of measurement with packets . 59
8.5.3 Limits . 60
8.6 Adjacent channel selectivity . 60
8.6.1 Definition . 60
8.6.2 Method of measurement . 61
8.6.2.1 Method of measurement with continuous bit streams . 61
8.6.2.2 Method of measurement with messages . 62
8.6.2.3 Method of measurement with packe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.