ETSI EN 301 842-3 V1.4.1 (2015-04)
VHF air-ground Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of measurement for ground-based equipment; Part 3: Additional broadcast aspects
VHF air-ground Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of measurement for ground-based equipment; Part 3: Additional broadcast aspects
REN/AERO-00020-3
Radijska oprema za digitalno povezavo VHF zrak-tla, 4. način - Tehnične karakteristike in merilne metode za talno opremo - 3. del: Dodatni vidiki v zvezi z radiodifuzijo
Ta dokument se uporablja za radijsko opremo naslednjih vrst:
• talne radijske oddajnike in sprejemnike za zelo visokofrekvenčno (VHF) digitalno povezavo (VDL) za komunikacije zrak-tla, 4. način, ki delujejo v pasu VHF z uporabo modulacije frekvenčnega premičnega kodiranja prek filtra Gaussian (GFSK) z razmikom 25 kHz med kanali in so zmožni uravnavati na katerem koli izmed kanalov 25 kHz od 112.000 MHz do 136.975 MHz, kot je opredeljeno v standardih in priporočenih praksah (SARP) [1] za digitalne povezave ICAO VHF (VDL).
Ta dokument vsebuje 3. del tehničnih specifikacij.
Ta dokument zagotavlja, da bo oprema, ki bo certificirana v skladu z njim, združljiva z ustreznimi standardi in priporočenimi praksami (SARP) [1] za digitalne povezave ICAO VHF (VDL) in tehničnim priročnikom ICAO za digitalno povezavo VDL, 4. način (TM) [i.1].
Proizvajalci naj bodo pozorni, da razpon uravnavanja za talne oddajnike-sprejemnike lahko v prihodnje zajema tudi kateri koli kanal 25 kHz od 108,000 MHz do 111,975 MHz.
Področje uporabe tega dokumenta je omejeno na zemeljske postaje. Enakovredna specifikacija za letalske postaje je ETSI EN 302 842 [i.4].
Opis področja uporabe sistema VDL, 4. način, je naveden v standardu ETSI EN 301 842-2 [3], 1. točka.
ETSI EN 301 842-1 [2] obravnava preskuse fizične plasti. Standard ETSI EN 301 842-2 [3] zajema preskuse plasti povezav, ki zadostujejo za podporo radiodifuzijskih funkcij, vključno z zahtevami in preskusi, ki zadostujejo za prepoznavanje in odgovarjanje na prenose, povezane s komunikacijo točka-točka. Ta dokument vsebuje tehnične specifikacije za talni oddajnik-sprejemnik VDL, 4. način, ki podpira polni avtomatski odvisni nadzor – difuzija (ADS-B) in izbirno dodatne funkcije ene storitve ali kombinacije naslednjih storitev:
• difuzija nadzornih podatkov (TIS-B);
• difuzija informacij za letalstvo (FIS-B);
• storitev izboljšave GNSS – difuzija (GNS-B).
Pričakuje se, da funkcije storitev TIS-B, FIS-B ali GNS-B v talni opremi omogoča procesor TIS-B, FIS B ali GNS-B, ki je lahko znotraj sprejemnika-oddajnika VDL, 4. način, lahko pa se nahaja tudi v ločeni enoti. Za podporo storitev TIS-B, FIS-B ali GNS-B je tako minimalna funkcionalnost, ki se zahteva od osnovne talne oddajno-sprejemne enote VDL, 4. način (tj. enote, ki ne vsebuje procesorja TIS-B, FIS-B ali GNS-B), sprejemanje vseh sporočil procesorja TIS-B, FIS-B ali GNS-B, ki so namenjena oddajanju, in jih oddajati. V primeru storitve FIS-B je dodatna zahteva sprejemanje sporočil z zahtevami za poročila od drugih postaj VDL4 in posredovati ta sporočila procesorju FIS-B.
Poudariti je treba, da specifikacije za storitve TIS-B, FIS-B in GNS-B v tem dokumentu predstavljajo prvi korak do njihove opredelitve, osnovane na delu, ki je bilo izvedeno v okviru programov NUP in MEDUP, zato se lahko specifikacije za te storitve v prihodnosti spremenijo.
Ta dokument je organiziran na naslednji način:
• točka 2 vsebuje sklice do ustreznih dokumentov;
• točka 3 vsebuje splošne opredelitve, kratice in simbole, ki se uporabljajo;
• točka 4 opisuje funkcionalnost zemeljskih postaj VDL, 4. način, za podporo storitev ADS-B, TIS-B, FIS-B in GNS B;
• točka 5 vsebuje specifikacije lastnosti zemeljskih postaj VDL, 4. način, ki podpirajo storitve ADS-B, TIS-B, FIS-B in GNS-B;
• točka 6 vsebuje splošne zahteve projekta;
• točka 7 vsebuje preskuse protokolov s poudarkom na funkcijah ADS-B, TIS-B, FIS-B in GNS-B sistema;
• dodatek A vsebuje podrobne sklice do ustreznih zahtev, ki so vključene v [i.1].
Upoštevati je treba, da lahko sistem podpira zelo širok nabor funkcij. Podajanje določenih preskusov za celoten nabor funkcij ni praktično. Tako so podani podrobni preskusi za osrednje funkcije za podporo storitev ADS-B, FIS B, TIS-B in GNS-B, ki se osredotočajo na zahteve sistema, ki lahko v primeru nepravilnega izvajanja povzročijo poslabšanje storitve, ki jo zagotavljajo druge postaje VDL, 4. način.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 301 842-3 V1.4.1:2015
01-oktober-2015
5DGLMVNDRSUHPD]DGLJLWDOQRSRYH]DYR9+)]UDNWODQDþLQ7HKQLþQH
NDUDNWHULVWLNHLQPHULOQHPHWRGH]DWDOQRRSUHPRGHO'RGDWQLYLGLNLY]YH]L]
UDGLRGLIX]LMR
9+)DLUJURXQG'LJLWDO/LQN9'/0RGHUDGLRHTXLSPHQW7HFKQLFDOFKDUDFWHULVWLFVDQG
PHWKRGVRIPHDVXUHPHQWIRUJURXQGEDVHGHTXLSPHQW
3DUW$GGLWLRQDOEURDGFDVWDVSHFWV
Ta slovenski standard je istoveten z: EN 301 842-3 V1.4.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
49.090 2SUHPDLQLQVWUXPHQWLY On-board equipment and
]UDþQLKLQYHVROMVNLKSORYLOLK instruments
SIST EN 301 842-3 V1.4.1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 301 842-3 V1.4.1:2015
---------------------- Page: 2 ----------------------
SIST EN 301 842-3 V1.4.1:2015
ETSI EN 301 842-3 V1.4.1 (2015-04)
EUROPEAN STANDARD
VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement
for ground-based equipment;
Part 3: Additional broadcast aspects
---------------------- Page: 3 ----------------------
SIST EN 301 842-3 V1.4.1:2015
2 ETSI EN 301 842-3 V1.4.1 (2015-04)
Reference
REN/AERO-00020-3
Keywords
aeronautical, digital, radio, testing, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 842-3 V1.4.1:2015
3 ETSI EN 301 842-3 V1.4.1 (2015-04)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.1.1 Basic reference model definitions . 9
3.1.2 Service conventions definitions . 9
3.1.3 General definitio ns . 9
3.2 Abbreviations . 10
4 General description of VDL Mode 4 ground station link layer . 11
4.1 General . 11
4.2 Automatic Dependant Surveillance-Broadcast . 12
4.3 Traffic Information Service-Broadcast . 12
4.4 Flight Information Service-Broadcast . 13
4.5 GNSS Augmentation Service-Broadcast (GNS-B) . 14
4.6 Ground Station Coordination . 15
5 Minimum performance specification under standard test conditions . 16
5.1 Requirements for ADS-B . 16
5.1.1 Information Field Formats . 16
5.1.2 ADS-B Request . 26
5.1.2.1 ADS-B request format. 26
5.1.2.2 Sleep Mode . 26
5.1.2.3 Automatic Selection of Variable Information Fields . 26
5.1.3 Default ADS-B Reporting . 29
5.1.4 ADS-B Procedures . 29
5.1.5 CTRL Parameters . 30
5.1.5.1 Directory of Service (DOS) message . 30
5.1.5.2 Channel Management Parameter . 30
5.1.6 Definitions for Compact Position Reporting . 39
5.1.6.1 Information Field Offset Encoding . 39
5.1.6.2 Information Field Offset Decoding . 41
5.1.6.3 Patch ID Encoding . 42
5.1.6.4 Patch ID Decoding . 42
5.1.7 Encoding of UDATA (udid) . 43
5.2 Requirements for TIS-B . 43
5.2.1 Traffic Information Volume (TIV) . 43
5.2.2 Message transmission . 44
5.2.2.1 Management messages . 44
5.2.2.2 Target messages . 44
5.2.2.3 Airport operation . 44
5.2.3 Message format . 45
5.2.4 Management message . 46
5.2.5 Aircraft target messages (airborne TIV) . 48
5.2.6 Aircraft target messages (ground TIV) . 50
5.2.7 Ground vehicle target messages (ground TIV) . 51
5.2.8 TIS-B offset encoding . 52
5.3 Requirements for FIS-B . 56
5.3.1 Message format . 56
5.3.2 Meteorological Aerodrome Report (METAR) message . 57
ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 842-3 V1.4.1:2015
4 ETSI EN 301 842-3 V1.4.1 (2015-04)
5.3.3 Special Observations and Reports (SPECI) message . 64
5.3.4 Automatic Terminal Information Service (ATIS) message . 65
5.3.5 Runway Condition (RCN) message . 68
5.3.6 SIGnificant METeorological Information (SIGMET) message . 72
5.3.7 Temporary Segregated Areas (TSA) message . 73
5.3.8 FIS-B report request message . 76
5.3.9 Ground system functions . 77
5.4 Requirements for GNSS Augmentation Service Broadcast (GNS-B) message . 78
5.4.1 Message format . 78
5.4.2 Message Type 1 . 78
5.4.3 Message Type 2 . 82
5.4.4 Message Type 4 . 86
5.4.5 CRC Calculation . 92
5.4.5.1 GNS-B CRC . 92
5.4.5.2 FAS CRC . 92
5.4.5.3 Ephemeris CRC . 93
6 General design requirements . 93
7 Protocol test procedures . 93
7.1 General . 93
7.2 Required test rig . 93
7.3 Protocol test-suite description methodology . 96
7.4 Detailed protocol test procedures . 96
7.4.1 Test-suite overview . 96
7.4.2 Declarations . 98
7.4.3 Constraints . 98
7.4.3.1 Abbreviations . 98
7.4.3.1.1 Subfield mnemonics . 98
7.4.3.1.2 Station addresses and positions . 102
7.4.3.1.3 Tables of values for use in CPR test cases . 103
7.4.3.1.4 Tables of values for use in content checking test cases . 115
7.4.3.1.5 VDL4 Burst formats . 149
7.4.3.2 Test cases . 185
7.4.3.2.1 Test case macros . 186
7.4.3.2.2 Test case descriptions . 187
Annex A (informative): Cross reference matrix . 259
History . 274
ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 842-3 V1.4.1:2015
5 ETSI EN 301 842-3 V1.4.1 (2015-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Aeronautics (AERO).
The present document is part 3 of a multi-part deliverable covering the VHF air-ground Digital Link (VDL) Mode 4
radio equipment; Technical characteristics and methods of measurement for ground-based equipment, as identified
below:
Part 1: "EN for ground equipment";
Part 2: "General description and data link layer";
Part 3: "Additional broadcast aspects";
Part 4: "Point-to-point functions";
Part 5: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
The present document is accompanied by an equivalent airborne standard, ETSI EN 302 842 parts 1-4 [i.4], covering
the VHF air-ground Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of
measurement for airborne equipment.
National transposition dates
Date of adoption of this EN: 6 April 2015
Date of latest announcement of this EN (doa): 31 July 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2016
Date of withdrawal of any conflicting National Standard (dow): 31 January 2017
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 842-3 V1.4.1:2015
6 ETSI EN 301 842-3 V1.4.1 (2015-04)
Introduction
The present document states the technical specifications for Very High Frequency (VHF) Digital Link (VDL) Mode 4
ground-based radio transmitters, transceivers and receivers for air-ground communications operating in the VHF band,
using Gaussian-filtered Frequency Shift Keying (GFSK) Modulation with 25 kHz channel spacing and capable of
tuning to any of the 25 kHz channels from 112,000 MHz to 136,975 MHz as defined in ICAO VHF Digital Link (VDL)
Standards and Recommended Practices (SARPs) [1].
The present document considers the additional broadcast functionality required to support ADS-B, TIS-B, FIS-B, and
GNS-B services.
The present document may be used to produce tests for the assessment of the performance of the equipment.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 842-3 V1.4.1:2015
7 ETSI EN 301 842-3 V1.4.1 (2015-04)
1 Scope
The present document applies to the following radio equipment types:
• Very High Frequency (VHF) Digital Link (VDL) Mode 4 ground-based radio transmitters and receivers for
air-ground communications operating in the VHF band, using Gaussian-filtered Frequency Shift Keying
(GFSK) Modulation with 25 kHz channel spacing and capable of tuning to any of the 25 kHz channels from
112,000 MHz to 136,975 MHz as defined in ICAO VHF Digital Link (VDL) Standards and Recommended
Practices (SARPs) [1].
The present document provides part 3 of the technical specifications.
The present document is designed to ensure that equipment certified to it will be compatible with the relevant ICAO
VHF Digital Link (VDL) Standards and Recommended Practices (SARPs) [1] and VDL Mode 4 Technical
Manual (TM) [i.1].
Manufacturers should note that in future the tuning range for the ground transceivers may also cover any 25 kHz
channel from 108,000 MHz to 111,975 MHz.
The scope of the present document is limited to ground stations. The equivalent specification for airborne stations is
ETSI EN 302 842 [i.4].
A description of the scope of the VDL Mode 4 system is provided in ETSI EN 301 842-2 [3], clause 1.
ETSI EN 301 842-1 [2] deals with tests of the physical layer. ETSI EN 301 842-2 [3] deals with tests of the link layer
sufficient to support broadcast functionality including requirements and tests sufficient to recognize and respond to
transmissions associated with point-to-point communication. The present document provides technical specifications
for a VDL Mode 4 ground-based transceiver supporting a full Automatic Dependent Surveillance-Broadcast (ADS-B)
capability and, optionally, the additional functionality of either, or a combination of, the following services:
• Traffic Information Service-Broadcast (TIS-B);
• Flight Information Service-Broadcast (FIS-B);
• GNSS Augmentation Service-Broadcast (GNS-B).
The TIS-B, FIS-B or GNS-B functionality in the ground-based equipment is expected to be provided by a TIS-B, FIS B
or GNS-B processor, which could be contained within the VDL Mode 4 transceiver, but could also be housed in a
separate physical unit. Therefore to support TIS-B, FIS-B or GNS-B, the minimum functionality demanded of a basic
VDL Mode 4 ground-based transceiver unit (i.e. one that does not have a TIS-B, FIS-B or GNS-B processor housed
within it) is to receive, from the TIS-B, FIS-B or GNS-B processor, all messages to be transmitted, and to transmit
them. In the case of FIS-B there is an additional requirement to receive report request messages (from other VDL4
stations) and to pass those messages to the FIS-B processor.
It should be noted that the specifications for TIS-B, FIS-B and GNS-B in the present document represent a first step
towards defining these applications, based on the work carried out as part of the NUP and MEDUP Programmes, and
changes to the specifications for these services may therefore occur in the future.
The present document is organized as follows:
• clause 2 provides references to relevant documents;
• clause 3 provides general definitions, abbreviations and symbols used;
• clause 4 describes the VDL Mode 4 ground station functionality to support ADS-B, TIS-B, FIS-B and GNS B;
• clause 5 provides performance specifications for the VDL Mode 4 ground station supporting ADS-B, TIS-B,
FIS-B and GNS-B Services;
• clause 6 provides general design requirements;
• clause 7 provides protocol tests which emphasis the ADS-B, TIS-B, FIS-B and GNS-B functions of the
system;
ETSI
---------------------- Page: 9 ----------------------
SIST EN 301 842-3 V1.4.1:2015
8 ETSI EN 301 842-3 V1.4.1 (2015-04)
• annex A provides a detailed cross-reference to the relevant requirements contained in [i.1].
Note that the system can support a very wide range of functions. It is not practical to provide specific tests for all
aspects of functionality. The approach used is to provide detailed tests for the core functionality to support ADS-B, FIS
B, TIS-B and GNS-B focusing on the system requirements which, if wrongly implemented, could cause a deterioration
in the service offered by other VDL Mode 4 stations.
Mandating and Recommendation Phrases
a) "Shall":
the use of the word "Shall" indicates a mandated criterion; i.e. compliance with the particular procedure or
specification is mandatory and no alternative may be applied.
b) "Should":
the use of the word "Should" (and phrases such as "It is recommended that.", etc.) indicates that though the
procedure or criterion is regarded as the preferred option, alternative procedures, specifications or criteria may
be applied, provided that the manufacturer, installer or tester can provide information or data to adequately
support and justify the alternative.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ICAO Annex 10 to the Convention on International Civil Aviation: "Aeronautical
Telecommunications, Volume III: Communication Systems, Part I: Digital Data Communication
Systems, chapter 6", including Amendment 88 (applicable 14/11/13).
[2] ETSI EN 301 842-1 (V1.4.1): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 1: EN for
ground equipment".
[3] ETSI EN 301 842-2 (V1.7.1): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 2:
General description and data link layer".
[4] ETSI EN 301 842-4 (V1.3.1): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 4: Point-
to-point functions".
[5] EUROCAE ED-114A (March 2013): "MOPS for Global Navigation Satellite Ground Based
Augmentation System Ground Equipment to Support Category I Operations".
[6] Amendments 76 and 77 to Volume I of Annex 10 to the Convention on International Civil
Aviation, International Civil Aviation Organization: appendix B-B2, 3.6 Ground-Based
Augmentation System (GBAS).
ETSI
---------------------- Page: 10 ----------------------
SIST EN 301 842-3 V1.4.1:2015
9 ETSI EN 301 842-3 V1.4.1 (2015-04)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ICAO Doc 9816 AN/448 (First Edition 2004): "Manual on VHF Digital Link (VDL) Mode 4,
Part 2: Detailed Technical Specifications".
[i.2] RTCA DO-242A: "Minimum Aviation System Performance Standards for Automatic Dependent
Surveillance Broadcast (ADS-B)".
[i.3] WMO Publication No. 306: "Manual on Codes Vol 1.1, Part A".
[i.4] ETSI EN 302 842 (all parts): "VHF air-ground and air-air Digital Link (VDL) Mode 4 radio
equipment; Technical characteristics and methods of measurement for aeronautical mobile
(airborne) equipment".
[i.5] North European ADS-B Network Update Programme: "FIS-B Service Description" V1.5.1,
th
10 October 2003.
[i.6] North European ADS-B Network Update Programme: "TIS-B Service Description" V1.33,
th
11 February 2003.
[i.7] North European ADS-B Network Update Programme: "GRAS Service Description" V1.2,
th
19 November 2003.
[i.8] EUROCAE ED-108A: "MOPS for VDL Mode 4 Aircraft Transceiver for ADS-B".
3 Definitions and abbreviations
3.1 Defini
...
ETSI EN 301 842-3 V1.4.1 (2015-04)
EUROPEAN STANDARD
VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement
for ground-based equipment;
Part 3: Additional broadcast aspects
---------------------- Page: 1 ----------------------
2 ETSI EN 301 842-3 V1.4.1 (2015-04)
Reference
REN/AERO-00020-3
Keywords
aeronautical, digital, radio, testing, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 842-3 V1.4.1 (2015-04)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.1.1 Basic reference model definitions . 9
3.1.2 Service conventions definitions . 9
3.1.3 General definitio ns . 9
3.2 Abbreviations . 10
4 General description of VDL Mode 4 ground station link layer . 11
4.1 General . 11
4.2 Automatic Dependant Surveillance-Broadcast . 12
4.3 Traffic Information Service-Broadcast . 12
4.4 Flight Information Service-Broadcast . 13
4.5 GNSS Augmentation Service-Broadcast (GNS-B) . 14
4.6 Ground Station Coordination . 15
5 Minimum performance specification under standard test conditions . 16
5.1 Requirements for ADS-B . 16
5.1.1 Information Field Formats . 16
5.1.2 ADS-B Request . 26
5.1.2.1 ADS-B request format. 26
5.1.2.2 Sleep Mode . 26
5.1.2.3 Automatic Selection of Variable Information Fields . 26
5.1.3 Default ADS-B Reporting . 29
5.1.4 ADS-B Procedures . 29
5.1.5 CTRL Parameters . 30
5.1.5.1 Directory of Service (DOS) message . 30
5.1.5.2 Channel Management Parameter . 30
5.1.6 Definitions for Compact Position Reporting . 39
5.1.6.1 Information Field Offset Encoding . 39
5.1.6.2 Information Field Offset Decoding . 41
5.1.6.3 Patch ID Encoding . 42
5.1.6.4 Patch ID Decoding . 42
5.1.7 Encoding of UDATA (udid) . 43
5.2 Requirements for TIS-B . 43
5.2.1 Traffic Information Volume (TIV) . 43
5.2.2 Message transmission . 44
5.2.2.1 Management messages . 44
5.2.2.2 Target messages . 44
5.2.2.3 Airport operation . 44
5.2.3 Message format . 45
5.2.4 Management message . 46
5.2.5 Aircraft target messages (airborne TIV) . 48
5.2.6 Aircraft target messages (ground TIV) . 50
5.2.7 Ground vehicle target messages (ground TIV) . 51
5.2.8 TIS-B offset encoding . 52
5.3 Requirements for FIS-B . 56
5.3.1 Message format . 56
5.3.2 Meteorological Aerodrome Report (METAR) message . 57
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 842-3 V1.4.1 (2015-04)
5.3.3 Special Observations and Reports (SPECI) message . 64
5.3.4 Automatic Terminal Information Service (ATIS) message . 65
5.3.5 Runway Condition (RCN) message . 68
5.3.6 SIGnificant METeorological Information (SIGMET) message . 72
5.3.7 Temporary Segregated Areas (TSA) message . 73
5.3.8 FIS-B report request message . 76
5.3.9 Ground system functions . 77
5.4 Requirements for GNSS Augmentation Service Broadcast (GNS-B) message . 78
5.4.1 Message format . 78
5.4.2 Message Type 1 . 78
5.4.3 Message Type 2 . 82
5.4.4 Message Type 4 . 86
5.4.5 CRC Calculation . 92
5.4.5.1 GNS-B CRC . 92
5.4.5.2 FAS CRC . 92
5.4.5.3 Ephemeris CRC . 93
6 General design requirements . 93
7 Protocol test procedures . 93
7.1 General . 93
7.2 Required test rig . 93
7.3 Protocol test-suite description methodology . 96
7.4 Detailed protocol test procedures . 96
7.4.1 Test-suite overview . 96
7.4.2 Declarations . 98
7.4.3 Constraints . 98
7.4.3.1 Abbreviations . 98
7.4.3.1.1 Subfield mnemonics . 98
7.4.3.1.2 Station addresses and positions . 102
7.4.3.1.3 Tables of values for use in CPR test cases . 103
7.4.3.1.4 Tables of values for use in content checking test cases . 115
7.4.3.1.5 VDL4 Burst formats . 149
7.4.3.2 Test cases . 185
7.4.3.2.1 Test case macros . 186
7.4.3.2.2 Test case descriptions . 187
Annex A (informative): Cross reference matrix . 259
History . 274
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 842-3 V1.4.1 (2015-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Aeronautics (AERO).
The present document is part 3 of a multi-part deliverable covering the VHF air-ground Digital Link (VDL) Mode 4
radio equipment; Technical characteristics and methods of measurement for ground-based equipment, as identified
below:
Part 1: "EN for ground equipment";
Part 2: "General description and data link layer";
Part 3: "Additional broadcast aspects";
Part 4: "Point-to-point functions";
Part 5: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
The present document is accompanied by an equivalent airborne standard, ETSI EN 302 842 parts 1-4 [i.4], covering
the VHF air-ground Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of
measurement for airborne equipment.
National transposition dates
Date of adoption of this EN: 6 April 2015
Date of latest announcement of this EN (doa): 31 July 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2016
Date of withdrawal of any conflicting National Standard (dow): 31 January 2017
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 842-3 V1.4.1 (2015-04)
Introduction
The present document states the technical specifications for Very High Frequency (VHF) Digital Link (VDL) Mode 4
ground-based radio transmitters, transceivers and receivers for air-ground communications operating in the VHF band,
using Gaussian-filtered Frequency Shift Keying (GFSK) Modulation with 25 kHz channel spacing and capable of
tuning to any of the 25 kHz channels from 112,000 MHz to 136,975 MHz as defined in ICAO VHF Digital Link (VDL)
Standards and Recommended Practices (SARPs) [1].
The present document considers the additional broadcast functionality required to support ADS-B, TIS-B, FIS-B, and
GNS-B services.
The present document may be used to produce tests for the assessment of the performance of the equipment.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 842-3 V1.4.1 (2015-04)
1 Scope
The present document applies to the following radio equipment types:
• Very High Frequency (VHF) Digital Link (VDL) Mode 4 ground-based radio transmitters and receivers for
air-ground communications operating in the VHF band, using Gaussian-filtered Frequency Shift Keying
(GFSK) Modulation with 25 kHz channel spacing and capable of tuning to any of the 25 kHz channels from
112,000 MHz to 136,975 MHz as defined in ICAO VHF Digital Link (VDL) Standards and Recommended
Practices (SARPs) [1].
The present document provides part 3 of the technical specifications.
The present document is designed to ensure that equipment certified to it will be compatible with the relevant ICAO
VHF Digital Link (VDL) Standards and Recommended Practices (SARPs) [1] and VDL Mode 4 Technical
Manual (TM) [i.1].
Manufacturers should note that in future the tuning range for the ground transceivers may also cover any 25 kHz
channel from 108,000 MHz to 111,975 MHz.
The scope of the present document is limited to ground stations. The equivalent specification for airborne stations is
ETSI EN 302 842 [i.4].
A description of the scope of the VDL Mode 4 system is provided in ETSI EN 301 842-2 [3], clause 1.
ETSI EN 301 842-1 [2] deals with tests of the physical layer. ETSI EN 301 842-2 [3] deals with tests of the link layer
sufficient to support broadcast functionality including requirements and tests sufficient to recognize and respond to
transmissions associated with point-to-point communication. The present document provides technical specifications
for a VDL Mode 4 ground-based transceiver supporting a full Automatic Dependent Surveillance-Broadcast (ADS-B)
capability and, optionally, the additional functionality of either, or a combination of, the following services:
• Traffic Information Service-Broadcast (TIS-B);
• Flight Information Service-Broadcast (FIS-B);
• GNSS Augmentation Service-Broadcast (GNS-B).
The TIS-B, FIS-B or GNS-B functionality in the ground-based equipment is expected to be provided by a TIS-B, FIS B
or GNS-B processor, which could be contained within the VDL Mode 4 transceiver, but could also be housed in a
separate physical unit. Therefore to support TIS-B, FIS-B or GNS-B, the minimum functionality demanded of a basic
VDL Mode 4 ground-based transceiver unit (i.e. one that does not have a TIS-B, FIS-B or GNS-B processor housed
within it) is to receive, from the TIS-B, FIS-B or GNS-B processor, all messages to be transmitted, and to transmit
them. In the case of FIS-B there is an additional requirement to receive report request messages (from other VDL4
stations) and to pass those messages to the FIS-B processor.
It should be noted that the specifications for TIS-B, FIS-B and GNS-B in the present document represent a first step
towards defining these applications, based on the work carried out as part of the NUP and MEDUP Programmes, and
changes to the specifications for these services may therefore occur in the future.
The present document is organized as follows:
• clause 2 provides references to relevant documents;
• clause 3 provides general definitions, abbreviations and symbols used;
• clause 4 describes the VDL Mode 4 ground station functionality to support ADS-B, TIS-B, FIS-B and GNS B;
• clause 5 provides performance specifications for the VDL Mode 4 ground station supporting ADS-B, TIS-B,
FIS-B and GNS-B Services;
• clause 6 provides general design requirements;
• clause 7 provides protocol tests which emphasis the ADS-B, TIS-B, FIS-B and GNS-B functions of the
system;
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 842-3 V1.4.1 (2015-04)
• annex A provides a detailed cross-reference to the relevant requirements contained in [i.1].
Note that the system can support a very wide range of functions. It is not practical to provide specific tests for all
aspects of functionality. The approach used is to provide detailed tests for the core functionality to support ADS-B, FIS
B, TIS-B and GNS-B focusing on the system requirements which, if wrongly implemented, could cause a deterioration
in the service offered by other VDL Mode 4 stations.
Mandating and Recommendation Phrases
a) "Shall":
the use of the word "Shall" indicates a mandated criterion; i.e. compliance with the particular procedure or
specification is mandatory and no alternative may be applied.
b) "Should":
the use of the word "Should" (and phrases such as "It is recommended that.", etc.) indicates that though the
procedure or criterion is regarded as the preferred option, alternative procedures, specifications or criteria may
be applied, provided that the manufacturer, installer or tester can provide information or data to adequately
support and justify the alternative.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ICAO Annex 10 to the Convention on International Civil Aviation: "Aeronautical
Telecommunications, Volume III: Communication Systems, Part I: Digital Data Communication
Systems, chapter 6", including Amendment 88 (applicable 14/11/13).
[2] ETSI EN 301 842-1 (V1.4.1): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 1: EN for
ground equipment".
[3] ETSI EN 301 842-2 (V1.7.1): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 2:
General description and data link layer".
[4] ETSI EN 301 842-4 (V1.3.1): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 4: Point-
to-point functions".
[5] EUROCAE ED-114A (March 2013): "MOPS for Global Navigation Satellite Ground Based
Augmentation System Ground Equipment to Support Category I Operations".
[6] Amendments 76 and 77 to Volume I of Annex 10 to the Convention on International Civil
Aviation, International Civil Aviation Organization: appendix B-B2, 3.6 Ground-Based
Augmentation System (GBAS).
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 842-3 V1.4.1 (2015-04)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ICAO Doc 9816 AN/448 (First Edition 2004): "Manual on VHF Digital Link (VDL) Mode 4,
Part 2: Detailed Technical Specifications".
[i.2] RTCA DO-242A: "Minimum Aviation System Performance Standards for Automatic Dependent
Surveillance Broadcast (ADS-B)".
[i.3] WMO Publication No. 306: "Manual on Codes Vol 1.1, Part A".
[i.4] ETSI EN 302 842 (all parts): "VHF air-ground and air-air Digital Link (VDL) Mode 4 radio
equipment; Technical characteristics and methods of measurement for aeronautical mobile
(airborne) equipment".
[i.5] North European ADS-B Network Update Programme: "FIS-B Service Description" V1.5.1,
th
10 October 2003.
[i.6] North European ADS-B Network Update Programme: "TIS-B Service Description" V1.33,
th
11 February 2003.
[i.7] North European ADS-B Network Update Programme: "GRAS Service Description" V1.2,
th
19 November 2003.
[i.8] EUROCAE ED-108A: "MOPS for VDL Mode 4 Aircraft Transceiver for ADS-B".
3 Definitions and abbreviations
3.1 Definitions
3.1.1 Basic reference model definitions
See ETSI EN 301 842-2 [3], clause 3.1.1.
3.1.2 Service conventions definitions
See ETSI EN 301 842-2 [3], clause 3.1.2.
3.1.3 General definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 842-1 [2], clause 3.1.3,
ETSI EN 301 842-2 [3], clause 3.1.3 and the following apply:
Automatic Dependent Surveillance-Broadcast (ADS-B): surveillance application transmitting parameters, such as
position, track, ground speed and time via a broadcast mode data link for use by any air and ground users requiring it
NOTE: ADS-B is a surveillance service based on aircraft self-determination of position/velocity/time and
automatic, periodic, broadcast of this information along with auxiliary data such as aircraft identity (ID),
intent information and communications control parameters, etc. ADS-B is intended to support multiple
high-level applications and associated services such as cockpit display of traffic information, traffic alert
and collision avoidance functionality, enhanced traffic management in the air and on the ground, search
and rescue support and others.
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 301 842-3 V1.4
...
Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
EUROPEAN STANDARD
VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement
for ground-based equipment;
Part 3: Additional broadcast aspects
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
Reference
REN/AERO-00020-3
Keywords
aeronautical, digital, radio, testing, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.1.1 Basic reference model definitions . 9
3.1.2 Service conventions definitions . 9
3.1.3 General definitio ns . 9
3.2 Abbreviations . 10
4 General description of VDL Mode 4 ground station link layer . 11
4.1 General . 11
4.2 Automatic Dependant Surveillance-Broadcast . 12
4.3 Traffic Information Service-Broadcast . 12
4.4 Flight Information Service-Broadcast . 13
4.5 GNSS Augmentation Service-Broadcast (GNS-B) . 14
4.6 Ground Station Coordination . 15
5 Minimum performance specification under standard test conditions . 16
5.1 Requirements for ADS-B . 16
5.1.1 Information Field Formats . 16
5.1.2 ADS-B Request . 26
5.1.2.1 ADS-B request format. 26
5.1.2.2 Sleep Mode . 26
5.1.2.3 Automatic Selection of Variable Information Fields . 26
5.1.3 Default ADS-B Reporting . 29
5.1.4 ADS-B Procedures . 29
5.1.5 CTRL Parameters . 29
5.1.5.1 Directory of Service (DOS) message . 29
5.1.5.2 Channel Management Parameter . 30
5.1.6 Definitions for Compact Position Reporting . 39
5.1.6.1 Information Field Offset Encoding . 39
5.1.6.2 Information Field Offset Decoding . 41
5.1.6.3 Patch ID Encoding . 42
5.1.6.4 Patch ID Decoding . 42
5.1.7 Encoding of UDATA (udid) . 43
5.2 Requirements for TIS-B . 43
5.2.1 Traffic Information Volume (TIV) . 43
5.2.2 Message transmission . 44
5.2.2.1 Management messages . 44
5.2.2.2 Target messages . 44
5.2.2.3 Airport operation . 44
5.2.3 Message format . 45
5.2.4 Management message . 46
5.2.5 Aircraft target messages (airborne TIV) . 48
5.2.6 Aircraft target messages (ground TIV) . 50
5.2.7 Ground vehicle target messages (ground TIV) . 51
5.2.8 TIS-B offset encoding . 52
5.3 Requirements for FIS-B . 56
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
5.3.1 Message format . 56
5.3.2 Meteorological Aerodrome Report (METAR) message . 57
5.3.3 Special Observations and Reports (SPECI) message . 64
5.3.4 Automatic Terminal Information Service (ATIS) message . 65
5.3.5 Runway Condition (RCN) message . 68
5.3.6 SIGnificant METeorological Information (SIGMET) message . 72
5.3.7 Temporary Segregated Areas (TSA) message . 73
5.3.8 FIS-B report request message . 76
5.3.9 Ground system functions . 77
5.4 Requirements for GNSS Augmentation Service Broadcast (GNS-B) message . 78
5.4.1 Message format . 78
5.4.2 Message Type 1 . 79
5.4.3 Message Type 2 . 82
5.4.4 Message Type 4 . 86
5.4.5 CRC Calculation . 92
5.4.5.1 GNS-B CRC . 92
5.4.5.2 FAS CRC . 92
5.4.5.3 Ephemeris CRC . 93
6 General design requirements . 93
7 Protocol test procedures . 93
7.1 General . 93
7.2 Required test rig . 94
7.3 Protocol test-suite description methodology . 96
7.4 Detailed protocol test procedures . 96
7.4.1 Test-suite overview . 96
7.4.2 Declarations . 98
7.4.3 Constraints . 98
7.4.3.1 Abbreviations . 98
7.4.3.1.1 Subfield mnemonics . 99
7.4.3.1.2 Station addresses and positions . 102
7.4.3.1.3 Tables of values for use in CPR test cases . 103
7.4.3.1.4 Tables of values for use in content checking test cases . 113
7.4.3.1.5 VDL4 Burst formats . 147
7.4.3.2 Test cases . 183
7.4.3.2.1 Test case macros . 184
7.4.3.2.2 Test case descriptions . 185
Annex A (informative): Cross reference matrix . 257
History . 272
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Aeronautics (AERO), and is now
submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN Approval Procedure.
The present document is part 3 of a multi-part deliverable covering the VHF air-ground Digital Link (VDL) Mode 4
radio equipment; Technical characteristics and methods of measurement for ground-based equipment, as identified
below:
Part 1: "EN for ground equipment";
Part 2: "General description and data link layer";
Part 3: "Additional broadcast aspects";
Part 4: "Point-to-point functions";
Part 5: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
The present document is accompanied by an equivalent airborne standard, ETSI EN 302 842 parts 1-4 [i.4], covering
the VHF air-ground Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of
measurement for airborne equipment.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
Introduction
The present document states the technical specifications for Very High Frequency (VHF) Digital Link (VDL) Mode 4
ground-based radio transmitters, transceivers and receivers for air-ground communications operating in the VHF band,
using Gaussian-filtered Frequency Shift Keying (GFSK) Modulation with 25 kHz channel spacing and capable of
tuning to any of the 25 kHz channels from 112,000 MHz to 136,975 MHz as defined in ICAO VHF Digital Link (VDL)
Standards and Recommended Practices (SARPs) [1].
The present document considers the additional broadcast functionality required to support ADS-B, TIS-B, FIS-B, and
GNS-B services.
The present document may be used to produce tests for the assessment of the performance of the equipment.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
1 Scope
The present document applies to the following radio equipment types:
• Very High Frequency (VHF) Digital Link (VDL) Mode 4 ground-based radio transmitters and receivers for
air-ground communications operating in the VHF band, using Gaussian-filtered Frequency Shift Keying
(GFSK) Modulation with 25 kHz channel spacing and capable of tuning to any of the 25 kHz channels from
112,000 MHz to 136,975 MHz as defined in ICAO VHF Digital Link (VDL) Standards and Recommended
Practices (SARPs) [1].
The present document provides part 3 of the technical specifications.
The present document is designed to ensure that equipment certified to it will be compatible with the relevant ICAO
VHF Digital Link (VDL) Standards and Recommended Practices (SARPs) [1] and VDL Mode 4 Technical
Manual (TM) [i.1].
Manufacturers should note that in future the tuning range for the ground transceivers may also cover any 25 kHz
channel from 108,000 MHz to 111,975 MHz.
The scope of the present document is limited to ground stations. The equivalent specification for airborne stations is
ETSI EN 302 842 [i.4].
A description of the scope of the VDL Mode 4 system is provided in ETSI EN 301 842-2 [3], clause 1.
ETSI EN 301 842-1 [2] deals with tests of the physical layer. ETSI EN 301 842-2 [3] deals with tests of the link layer
sufficient to support broadcast functionality including requirements and tests sufficient to recognize and respond to
transmissions associated with point-to-point communication. The present document provides technical specifications
for a VDL Mode 4 ground-based transceiver supporting a full Automatic Dependent Surveillance-Broadcast (ADS-B)
capability and, optionally, the additional functionality of either, or a combination of, the following services:
• Traffic Information Service-Broadcast (TIS-B);
• Flight Information Service-Broadcast (FIS-B);
• GNSS Augmentation Service-Broadcast (GNS-B).
The TIS-B, FIS-B or GNS-B functionality in the ground-based equipment is expected to be provided by a TIS-B, FIS B
or GNS-B processor, which could be contained within the VDL Mode 4 transceiver, but could also be housed in a
separate physical unit. Therefore to support TIS-B, FIS-B or GNS-B, the minimum functionality demanded of a basic
VDL Mode 4 ground-based transceiver unit (i.e. one that does not have a TIS-B, FIS-B or GNS-B processor housed
within it) is to receive, from the TIS-B, FIS-B or GNS-B processor, all messages to be transmitted, and to transmit
them. In the case of FIS-B there is an additional requirement to receive report request messages (from other VDL4
stations) and to pass those messages to the FIS-B processor.
It should be noted that the specifications for TIS-B, FIS-B and GNS-B in the present document represent a first step
towards defining these applications, based on the work carried out as part of the NUP and MEDUP Programmes, and
changes to the specifications for these services may therefore occur in the future.
The present document is organized as follows:
• clause 2 provides references to relevant documents;
• clause 3 provides general definitions, abbreviations and symbols used;
• clause 4 describes the VDL Mode 4 ground station functionality to support ADS-B, TIS-B, FIS-B and GNS B;
• clause 5 provides performance specifications for the VDL Mode 4 ground station supporting ADS-B, TIS-B,
FIS-B and GNS-B Services;
• clause 6 provides general design requirements;
• clause 7 provides protocol tests which emphasis the ADS-B, TIS-B, FIS-B and GNS-B functions of the
system;
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
• annex A provides a detailed cross-reference to the relevant requirements contained in [i.1].
Note that the system can support a very wide range of functions. It is not practical to provide specific tests for all
aspects of functionality. The approach used is to provide detailed tests for the core functionality to support ADS-B, FIS
B, TIS-B and GNS-B focusing on the system requirements which, if wrongly implemented, could cause a deterioration
in the service offered by other VDL Mode 4 stations.
Mandating and Recommendation Phrases
a) "Shall":
the use of the word "Shall" indicates a mandated criterion; i.e. compliance with the particular procedure or
specification is mandatory and no alternative may be applied.
b) "Should":
the use of the word "Should" (and phrases such as "It is recommended that.", etc.) indicates that though the
procedure or criterion is regarded as the preferred option, alternative procedures, specifications or criteria may
be applied, provided that the manufacturer, installer or tester can provide information or data to adequately
support and justify the alternative.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ICAO Annex 10 to the Convention on International Civil Aviation: "Aeronautical
Telecommunications, Volume III: Communication Systems, Part I: Digital Data Communication
Systems, chapter 6", including Amendment 88 (applicable 14/11/13).
[2] ETSI EN 301 842-1 (V1.4.0): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 1: EN for
ground equipment".
[3] ETSI EN 301 842-2 (V1.7.0): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 2:
General description and data link layer".
[4] ETSI EN 301 842-4 (V1.3.0): "VHF air-ground Digital Link (VDL) Mode 4 radio equipment;
Technical characteristics and methods of measurement for ground-based equipment; Part 4: Point-
to-point functions".
[5] EUROCAE ED-114A (March 2013): "MOPS for Global Navigation Satellite Ground Based
Augmentation System Ground Equipment to Support Category I Operations".
[6] Amendments 76 and 77 to Volume I of Annex 10 to the Convention on International Civil
Aviation, International Civil Aviation Organization: appendix B-B2, 3.6 Ground-Based
Augmentation System (GBAS).
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ICAO Doc 9816 AN/448 (First Edition 2004): "Manual on VHF Digital Link (VDL) Mode 4,
Part 2: Detailed Technical Specifications".
[i.2] RTCA DO-242A: "Minimum Aviation System Performance Standards for Automatic Dependent
Surveillance Broadcast (ADS-B)".
[i.3] WMO Publication No. 306: "Manual on Codes Vol 1.1, Part A".
[i.4] ETSI EN 302 842 (all parts): "VHF air-ground and air-air Digital Link (VDL) Mode 4 radio
equipment; Technical characteristics and methods of measurement for aeronautical mobile
(airborne) equipment".
th
[i.5] North European ADS-B Network Update Programme: "FIS-B Service Description" V1.5.1, 10
October 2003.
[i.6] North European ADS-B Network Update Programme: "TIS-B Service Description" V1.33,
th
11 February 2003.
[i.7] North European ADS-B Network Update Programme: "GRAS Service Description" V1.2,
th
19 November 2003.
[i.8] EUROCAE ED-108A: "MOPS for VDL Mode 4 Aircraft Transceiver for ADS-B".
3 Definitions and abbreviations
3.1 Definitions
3.1.1 Basic reference model definitions
See ETSI EN 301 842-2 [3], clause 3.1.1.
3.1.2 Service conventions definitions
See ETSI EN 301 842-2 [3], clause 3.1.2.
3.1.3 General definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 842-1 [2], clause 3.1.3,
ETSI EN 301 842-2 [3], clause 3.1.3 and the following apply:
Automatic Dependent Surveillance-Broadcast (ADS-B): surveillance application transmitting parameters, such as
position, track, ground speed and time via a broadcast mode data link for use by any air and ground users requiring it
NOTE: ADS-B is a surveillance service based on aircraft self-determination of position/velocity/time and
automatic, periodic, broadcast of this information along with auxiliary data such as aircraft identity (ID),
intent information and communications control parameters, etc. ADS-B is intended to support multiple
high-level applications and associated services such as cockpit display of traffic information, traffic alert
and collision avoidance functionality, enhanced traffic management in the air and on the ground, search
and rescue support and others.
Automatic Terminal Information Service (ATIS): report generated by a ground station that includes weather
conditions, operating procedures, runways and approaches in use, and any other information that may affect the
departure, runway, and landing phase of flight
ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 301 842-3 V1.4.0 (2014-12)
Fl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.