ETSI I-ETS 300 225 ed.1 (1994-05)
Radio Equipment and Systems (RES); Technical characteristics and methods of measurement for survival craft portable VHF radiotelephone apparatus
Radio Equipment and Systems (RES); Technical characteristics and methods of measurement for survival craft portable VHF radiotelephone apparatus
DI/RES-01-01
Radijska oprema in sistemi (RES) – Tehnične karakteristike in merilne metode za prenosne radiotelefonske aparate VHF za rešilne čolne
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST I-ETS 300 225 E1:2003
01-december-2003
5DGLMVNDRSUHPDLQVLVWHPL5(6±7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH]D
SUHQRVQHUDGLRWHOHIRQVNHDSDUDWH9+)]DUHãLOQHþROQH
Radio Equipment and Systems (RES); Technical characteristics and methods of
measurement for survival craft portable VHF radiotelephone apparatus
Ta slovenski standard je istoveten z: I-ETS 300 225 Edition 1
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
SIST I-ETS 300 225 E1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST I-ETS 300 225 E1:2003
---------------------- Page: 2 ----------------------
SIST I-ETS 300 225 E1:2003
INTERIM
EUROPEAN I-ETS 300 225
TELECOMMUNICATION May 1994
STANDARD
Source: ETSI TC-RES Reference: DI/RES-01-01
ICS: 33.060.50
Maritime, radiotelephone
Key words:
Radio Equipment and Systems (RES);
Technical characteristics and methods of
measurement for survival craft portable VHF
radiotelephone apparatus
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
F-06921 Sophia Antipolis CEDEX - FRANCE
Postal address:
650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Office address:
c=fr, a=atlas, p=etsi, s=secretariat - secretariat@etsi.fr
X.400: Internet:
Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1994. All rights reserved.
New presentation - see History box
---------------------- Page: 3 ----------------------
SIST I-ETS 300 225 E1:2003
Page 2
I-ETS 300 225: May 1994
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.
---------------------- Page: 4 ----------------------
SIST I-ETS 300 225 E1:2003
Page 3
I-ETS 300 225: May 1994
Contents
Foreword .7
1 Scope .9
2 Normative references.9
3 Abbreviations.9
4 General requirements .10
4.1 Construction.10
4.2 Frequencies and power .10
4.3 Controls.10
4.4 Switching time.11
4.5 Safety precautions .11
4.6 Class of emission and modulation characteristics.11
4.7 Battery.11
4.8 Labelling.12
5 Test conditions, power sources and ambient temperatures .12
5.1 Normal and extreme test conditions .12
5.2 Test power source .12
5.3 Normal test conditions .12
5.3.1 Normal temperature and humidity.12
5.3.2 Normal power source .13
5.4 Extreme test conditions .13
5.4.1 Extreme temperatures.13
5.4.1.1 Upper extreme temperature .13
5.4.1.2 Lower extreme temperature .13
5.4.2 Extreme test power supply values.13
5.4.2.1 Upper extreme test voltage .13
5.4.2.2 Lower extreme test voltage .13
5.5 Procedure for tests at extreme temperatures.13
6 General conditions of measurement .13
6.1 Test connections.13
6.2 Arrangements for test signals applied to the receiver input.14
6.3 Receiver mute or squelch facility .14
6.4 Normal test modulation.14
6.5 Artificial antenna .14
6.6 Test channels .14
6.7 Measurement uncertainty and interpretation of the measuring results.14
6.7.1 Measurement uncertainty.14
6.7.2 Interpretation of the measurement results .15
7 Environmental tests.15
7.1 Introduction .15
7.2 Procedure .15
7.3 Performance check.15
7.4 Drop test on hard surface .16
7.4.1 Definition .16
7.4.2 Method of measurement .16
7.4.3 Requirement.16
7.5 Vibration test.16
7.5.1 Method of measurement .16
7.5.2 Requirement.17
7.6 Temperature tests.17
7.6.1 General.17
---------------------- Page: 5 ----------------------
SIST I-ETS 300 225 E1:2003
Page 4
I-ETS 300 225: May 1994
7.6.2 Dry heat cycle . 17
7.6.2.1 Method of measurement. 17
7.6.2.2 Requirement . 17
7.6.3 Damp heat cycle . 17
7.6.3.1 Method of measurement. 17
7.6.3.2 Requirement . 18
7.6.4 Low temperature cycle. 18
7.6.4.1 Method of measurement. 18
7.6.4.2 Requirement . 18
7.7 Corrosion test (sea water test) . 18
7.7.1 General . 18
7.7.2 Method of measurement. 18
7.7.3 Requirements . 19
7.8 Immersion test. 19
7.8.1 Method of measurement. 19
7.8.2 Requirements . 19
7.9 Thermal shock. 20
7.9.1 Method of measurement. 20
7.9.2 Requirements . 20
7.10 Solar radiation . 20
7.10.1 Method of measurement. 20
7.10.2 Requirements . 20
7.11 Oil resistance test. 20
7.11.1 Method of measurement. 20
7.11.2 Requirement . 20
8 Field measurement. 21
8.1 Transmitter Effective Radiated Power (ERP). 21
8.1.1 Definition. 21
8.1.2 Method of measurement. 21
8.1.3 Limit . 21
8.2 Spurious emissions from the transmitter. 22
8.2.1 Definition. 22
8.2.2 Method of measurement. 22
8.2.3 Limit . 22
8.3 Spurious emissions from the receiver. 22
8.3.1 Definition. 22
8.3.2 Method of measurement. 22
8.3.3 Limit . 22
9 Transmitter . 22
9.1 Frequency error. 22
9.1.1 Definition. 22
9.1.2 Method of measurement. 23
9.1.3 Limit . 23
9.2 Carrier power referenced to ERP. 23
9.2.1 Definition. 23
9.2.2 Method of measurement. 23
9.2.3 Limits . 23
9.3 Frequency deviation .23
9.3.1 Definition. 23
9.3.2 Maximum permissible frequency deviation. 23
9.3.2.1 Method of measurement. 23
9.3.2.2 Limit. 24
9.3.3 Reduction of frequency deviation at modulation frequencies above 3 kHz . 24
9.3.3.1 Method of measurement. 24
9.3.3.2 Limits. 24
9.4 Limitation characteristics of the modulator. 24
9.4.1 Definition. 24
9.4.2 Method of measurement. 24
9.4.3 Limits . 25
9.5 Sensitivity of the modulator, including microphone . 25
9.5.1 Definition. 25
---------------------- Page: 6 ----------------------
SIST I-ETS 300 225 E1:2003
Page 5
I-ETS 300 225: May 1994
9.5.2 Method of measurement .25
9.5.3 Limit.25
9.6 Audio frequency response .25
9.6.1 Definition .25
9.6.2 Method of measurement .25
9.6.3 Limit.25
9.7 Audio frequency harmonic distortion of the emission .25
9.7.1 Definition .25
9.7.2 Method of measurement .25
9.7.2.1 Normal test conditions .25
9.7.2.2 Extreme test conditions .26
9.7.3 Limit.26
9.8 Adjacent channel power.26
9.8.1 Definition .26
9.8.2 Method of measurement .26
9.8.3 Limits.26
9.9 Residual modulation of the transmitter .26
9.9.1 Definition .26
9.9.2 Method of measurement .27
9.9.3 Limit.27
9.10 Transient frequency behaviour of the transmitter .27
9.10.1 Definitions.27
9.10.2 Method of measurement .27
9.10.3 Limits.29
10 Receiver .30
10.1 Harmonic distortion and rated audio frequency output power .30
10.1.1 Definition .30
10.1.2 Methods of measurement .30
10.1.3 Limits.30
10.2 Audio frequency response .30
10.2.1 Definition .30
10.2.2 Method of measurement .30
10.2.3 Limits.31
10.3 Maximum usable sensitivity .31
10.3.1 Definition .31
10.3.2 Method of measurement .31
10.3.3 Limits.31
10.4 Co-channel rejection.31
10.4.1 Definition .31
10.4.2 Method of measurement .31
10.4.3 Limit.32
10.5 Adjacent channel selectivity.32
10.5.1 Definition .32
10.5.2 Method of measurement .32
10.5.3 Limits.32
10.6 Spurious response rejection .32
10.6.1 Definition .32
10.6.2 Method of measurement .32
10.6.3 Limit.33
10.7 Intermodulation response .33
10.7.1 Definition .33
10.7.2 Method of measurement .33
10.7.3 Limit.33
10.8 Blocking or desensitisation .33
10.8.1 Definition .33
10.8.2 Method of measurement .33
10.8.3 Limit.34
10.9 Amplitude response of the receiver limiter.34
10.9.1 Definition .34
10.9.2 Method of measurement .34
10.9.3 Limit.34
10.10 Receiver noise .34
---------------------- Page: 7 ----------------------
SIST I-ETS 300 225 E1:2003
Page 6
I-ETS 300 225: May 1994
10.10.1 Definition. 34
10.10.2 Method of measurement. 34
10.10.3 Limit . 34
11 Secondary battery charger. 35
11.1 General. 35
11.2 Environmental tests. 35
11.2.1 Introduction . 35
11.2.2 Vibration test. 35
11.2.2.1 Method of measurement. 35
11.2.2.2 Requirement . 36
11.2.3 Temperature tests . 36
11.2.3.1 General . 36
11.2.3.2 Dry heat cycle. 36
11.2.3.3 Damp heat cycle . 36
11.2.3.4 Low temperature cycle. 36
11.2.4 Corrosion test . 37
11.2.4.1 General . 37
11.2.4.2 Method of measurement. 37
11.2.4.3 Requirements. 38
11.3 Charging time. 38
Annex A (normative): Measuring receiver for adjacent channel power measurement. 39
A.1 Power measuring receiver specification . 39
A.1.1 IF filter . 39
A 1.2 Attenuation indicator. 40
A.1.3 rms value indicator . 40
A.1.4 Oscillator and amplifier. 40
Annex B (normative): Solar radiation test source .41
B.1 Simulated solar radiation source . 41
History. 42
---------------------- Page: 8 ----------------------
SIST I-ETS 300 225 E1:2003
Page 7
I-ETS 300 225: May 1994
Foreword
This Interim European Telecommunication Standard (I-ETS) has been produced by the Radio Equipment
and Systems (RES) Technical Committee of the European Telecommunications Standards Institute
(ETSI).
This I-ETS defines the minimum technical characteristics required for portable VHF radio telephones
operating in survival craft, and optionally on board ships at sea, in certain frequency bands allocated to the
Maritime Mobile Service (MMS). It also incorporates the requirements detailed in the Radio Regulations,
SOLAS 1974 (as amended in 1988) [3] and the relevant recommendations of the International Maritime
Organization.
Every I-ETS prepared by ETSI is a voluntary standard. This I-ETS contains text concerning type approval
of the equipment to which it relates. This text does not make this I-ETS mandatory in its status as a
standard. However, this I-ETS can be referenced, wholly or in part, for mandatory application by decisions
of regulatory bodies.
---------------------- Page: 9 ----------------------
SIST I-ETS 300 225 E1:2003
Page 8
I-ETS 300 225: May 1994
Blank page
---------------------- Page: 10 ----------------------
SIST I-ETS 300 225 E1:2003
Page 9
I-ETS 300 225: May 1994
1 Scope
This I-ETS states the minimum technical characteristics required for portable VHF radiotelephones
operating in the bands between 156 and 174 MHz allocated to the Maritime Mobile Services by the ITU
Radio Regulations (see Radio Regulations, Appendices 18 [1] and 19 [2]) and suitable for use in survival
craft and, optionally, on board ships at sea. The requirements detailed in the Radio Regulations, in
SOLAS 1974 [3], as amended 1988, and the International Maritime Organisation Resolutions A.694(17)
[5] and A.762(18) [4] are incorporated in this I-ETS.
2 Normative references
This I-ETS incorporates by dated or undated reference provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent references to or revisions of any of these publication apply to
this I-ETS only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies.
[1] International Radio Regulations, Appendix 18: "Table of Transmitting
Frequencies in the Band 156 - 174 MHz for Stations in the Maritime Mobile
Service".
[2] International Radio Regulations, Appendix 19: "Technical Characteristics for
Transmitters and Receivers used in the Maritime Mobile Service in the band 156
- 174 MHz".
[3] International Convention for the Safety of Life at Sea (SOLAS) 1974 as
amended.
[4] International Maritime Organization Resolution A.762(18): "Performance
standards for survival craft two way VHF radiotelephone apparatus".
[5
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.