IEC 60793-1-49:2003/COR1:2005
(Corrigendum)Corrigendum 1 - Optical fibres - Part 1-49: Measurement methods and test procedures - Differential mode delay
Corrigendum 1 - Optical fibres - Part 1-49: Measurement methods and test procedures - Differential mode delay
Corrigendum 1 - Fibres optiques - Partie 1-49: Méthodes de mesure et procédures d'essai - Retard différentiel de mode
General Information
Relations
Standards Content (Sample)
CEI 60793-1-49 IEC 60793-1-49
(Première édition – 2003-03) (First edition – 2003-03)
Fibres optiques – Optical fibres –
Partie 1-49: Méthodes de mesure et procédures Part 1-49: Measurement methods and test
d'essai – Retard différentiel de mode procedures – Differential mode delay
CORRIGENDUM 1
Page 6 Page 7
AVANT-PROPOS FOREWORD
Dans le paragraphe concernant le cycle de In the paragraph concerning the mainte
...
This May Also Interest You
IEC 60794-1-307:2025 describes test procedures used in establishing uniform requirements of tubes for the mechanical property kinking. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This first edition partially cancels and replaces the second edition of IEC 60794‑1-23 published in 2019. This edition constitutes a technical revision.This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019:
a) renumbering of the existing test method G7 as G7A;
b) addition of test parameter L and calculated loop diameter D in Table 1 for method G7A;
c) addition of a new test procedure for tubes routed within installation devices and numbering it as G7B.
- Standard24 pagesEnglish and French languagesale 15% off
IEC 60793-1-40:2024 establishes uniform requirements for measuring the attenuation of optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. Four methods are described for measuring attenuation, one being that for modelling spectral attenuation:
-method A: cut-back;
-method B: insertion loss;
-method C: backscattering;
-method D: modelling spectral attenuation.
Methods A to C apply to the measurement of attenuation for all categories of the following fibres:
-class A multimode fibres;
-class B single-mode fibres.
Method C, backscattering, also covers the location, losses and characterization of point discontinuities.
Method D is applicable only to class B fibres.
Information common to all four methods appears in Clause 1 to Clause 11, and information pertaining to each individual method appears in Annex A, Annex B, Annex C, and Annex D, respectively.
This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) modifying the definition of attenuation to be compatible with the definition in electropedia.org
- Standard102 pagesEnglish languagesale 15% off
IEC TR 63484:2024 information about fungal growth on the outer sheath of optical fibre cables and on the inner components of the cable. It also provides guidance for specifying fungus resistance performance of optical cable outer sheath and internal cable components, including recommendations for fungus resistance test method as well as evaluation after test.
This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to hybrid telecommunication cables having a combination of both optical fibres and electrical conductors.
Since conditions suitable for fungal growth include high relative humidity and a warm atmosphere, the document is applicable to optical cables intended for transportation, storage and use under such environment over certain period, for instance, some days at least.
- Technical report15 pagesEnglish languagesale 15% off
IEC 60793-1-22:2024 establishes uniform requirements for measuring the length and elongation of optical fibre (typically within cable). The length of an optical fibre is a fundamental value for the evaluation of transmission characteristics such as losses and bandwidths.
- Standard123 pagesEnglish languagesale 15% off
- Standard81 pagesEnglish and French languagesale 15% off
IEC 60793-1-46:2024 establishes uniform requirements for the monitoring of changes in attenuation, thereby assisting in the inspection of fibres and cables for commercial purposes. This document gives two methods for monitoring the changes in attenuation of optical fibres and cables that occur during mechanical or environmental testing, or both. It provides a monitor in the change of attenuation characteristics arising from optical discontinuity, physical defects and modifications of the attenuation slope:
- method A: change in attenuation by transmitted power;
- method B: change in attenuation by backscattering.
Methods A and B apply to the monitoring of all categories of the following fibres:
- class A: multimode fibres;
- class B: single-mode fibres;
- class C: single-mode intraconnection fibres.
Information common to both measurements is contained in Clause 1 to Clause 10, and information pertaining to each individual method appears in Annex A, and Annex B respectively.
- Standard39 pagesEnglish languagesale 15% off
- Standard24 pagesEnglish and French languagesale 15% off
IEC 60794-1-209:2024 defines test procedures to be used in establishing uniform requirements for the environmental performance of:
- optical fibre cables for use with telecommunication equipment and devices employing similar techniques; and
- cables having a combination of both optical fibres and electrical conductors.
Throughout this document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document defines a test standard to determine cable aging performance by high temperature exposure and temperature cycling in order to simulate lifetime behaviour of the attenuation of cables, or physical attributes. See IEC 60794‑1‑2 for a reference guide to test methods of all types and for general requirements and definitions.
This document partially cancels and replaces IEC 60794‑1‑22:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794‑1‑22:2017:
a) the ambient temperature test condition has been defined as per IEC 60794‑1‑2;
b) all the maximum allowable attenuation increase values for single-mode and multimode fibres have been deleted, and have been included in the list of details to be specified.
- Standard17 pagesEnglish and French languagesale 15% off
IEC 60794-1-201: 2024 defines test procedures to be used in establishing uniform requirements for the environmental performance of:
- optical fibre cables for use with telecommunication equipment and devices employing similar techniques; and
- cables having a combination of both optical fibres and electrical conductors.
Throughout this document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document defines a test standard to determine the ability of a cable to withstand the effects of temperature cycling by observing changes in attenuation. See IEC 60794-1-2 for a reference guide to test methods of all types and for general requirements and definitions.
This document partially replaces IEC 60794-1-22:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794-1-22:2017:
a) all references to the temperature sensing device have been removed and replaced with a note "for further study";
b) the conditioning procedure has been separated into Procedure 1 and Procedure 2 to avoid confusion;
c) the ambient temperature test condition has been defined as per IEC 60794-1-2;
d) the minimum soak time has been decreased for sample mass >16 kg in Table 1.
- Standard25 pagesEnglish and French languagesale 15% off
IEC 60794-1-101:2024 applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors.
This document defines test procedures to be used in establishing uniform requirements for tensile performance.
Throughout this document the wording "optical cable" includes optical fibre units, microduct fibre units, etc.
See IEC 60794-1-2 for general requirements and definitions and for a complete reference guide to test methods of all types.
- Standard18 pagesEnglish and French languagesale 15% off
IEC 60794-1-213:2024 defines test procedures to be used in establishing uniform requirements for the environmental performance of microduct. The test determines the capability of the microduct to withstand internal pressure without leakage and visible damage. This document applies to microduct used for installation of microduct cable or fibre unit by blowing. Throughout this document, the wording "microduct" can also include protected microduct(s). See IEC 60794-1-2 for a reference guide to test methods of all types and for general requirements and definitions.This document partially cancels and replaces IEC 60794-1-22:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794-1-22:2017:
a) pressure gauge used to monitor internal pressure of microduct added as part of the test apparatus;
b) "test temperature" added to the details to be specified;
c) added a new subclause “4.7 Details to be reported”.
- Standard16 pagesEnglish and French languagesale 15% off
IEC 60794-1-104:2024 applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. This document defines test procedures to be used in establishing uniform requirements for impact performance. Throughout this document the wording “optical cable” includes optical fibre units, microduct fibre units, etc. See IEC 60794-1-2 for general requirements and definitions and for a complete reference guide to test methods of all types.
This document partially cancels and replaces IEC 60794-1-21:2015, which will be withdrawn. In the context of the revision of IEC 60794-1-21:2015, its contents were split into separate test methods. It includes an editorial revision, based on the new structure and numbering system for optical fibre cable test methods.
- Standard20 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.