ISO/IEC 24787-2:2024
(Main)Information technology — On-card biometric comparison — Part 2: Work-sharing mechanism
Information technology — On-card biometric comparison — Part 2: Work-sharing mechanism
This document provides requirements for a biometric comparison methodology suitable for the on-card environment. In particular, it establishes the work-sharing on-card biometric comparison techniques that require an intensity exceeding the capabilities of integrated circuit cards (ICCs). This document does not establish — architectures of biometric comparison using an ICC, — on-card biometric comparison, both in sensor-off-card systems and as part of biometric system-on-card, — security policies for on-card biometric comparison, — requirements for off-card biometric comparison, — requirements for biometric system-on-card (defined in the ISO/IEC 17839 series), or — modality-specific requirements for storage and comparison.
Technologies de l'information — Comparaison biométrique sur cartes — Partie 2: Mécanisme de partage des tâches
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO/IEC 24787-2
First edition
Information technology — On-card
2024-06
biometric comparison —
Part 2:
Work-sharing mechanism
Technologies de l'information — Comparaison biométrique sur
cartes —
Partie 2: Mécanisme de partage des tâches
Reference number
ISO/IEC 24787-2:2024(en) © ISO/IEC 2024
---------------------- Page: 1 ----------------------
ISO/IEC 24787-2:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO/IEC 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/IEC 24787-2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 2
5 Conformance . 2
6 Work-sharing on-card biometric comparison procedure . 2
Bibliography . 4
© ISO/IEC 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO/IEC 24787-2:2024(en)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical activity.
ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations,
governmental and non-governmental, in liaison with ISO and IEC, also take part in the work.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/
IEC Directives, Part 2 (see www.iso.org/directives or www.iec.ch/members_experts/refdocs).
ISO and IEC draw attention to the possibility that the implementation of this document may involve the
use of (a) patent(s). ISO and IEC take no position concerning the evidence, validity or applicability of any
claimed patent rights in respect thereof. As of the date of publication of this document, ISO and IEC had not
received notice of (a) patent(s) which may be required to implement this document. However, implementers
are cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/pat
...
FINAL DRAFT
International
Standard
ISO/IEC
FDIS
24787-2
ISO/IEC JTC 1/SC 17
Information technology — On-card
Secretariat: BSI
biometric comparison —
Voting begins on:
2024-02-23
Part 2:
Work-sharing mechanism
Voting terminates on:
2024-04-19
Technologies de l'information — Comparaison biométrique sur
cartes —
Partie 2: Mécanisme de partage des tâches
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/IEC FDIS 247872:2024(en) © ISO/IEC 2024
---------------------- Page: 1 ----------------------
FINAL DRAFT
ISO/IEC FDIS 24787-2:2024(en)
International
Standard
ISO/IEC
FDIS
24787-2
ISO/IEC JTC 1/SC 17
Information technology — On-card
Secretariat: BSI
biometric comparison —
Voting begins on:
Part 2:
Work-sharing mechanism
Voting terminates on:
Technologies de l'information — Comparaison biométrique sur
cartes —
Partie 2: Mécanisme de partage des tâches
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO/IEC 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/IEC FDIS 247872:2024(en) © ISO/IEC 2024
© ISO/IEC 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/IEC FDIS 24787-2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 2
5 Conformance . 2
6 Work-sharing on-card biometric comparison procedure . 2
Bibliography . 4
© ISO/IEC 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO/IEC FDIS 24787-2:2024(en)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form t
...
DRAFT INTERNATIONAL STANDARD
ISO/IEC DISFDIS 24787-2
ISO/IEC JTC 1/SC 17/WG 11
Date: 2022-04-12
Secretariat: BSI
Date: 2024-01-24
Information technology —– On-card biometric comparison – —
Part 2 : :
Work-sharing mechanism
Technologies de l'information — Comparison — Comparaison biométrique sur cartes — —
Partie 2: Mécanisme de partage du travaildes tâches
FDIS stage
---------------------- Page: 1 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/IEC DIS 24787-2:2022(E)
© ISO/IEC 20222024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
© ISO/IEC 2022 – All rights reserved 2
---------------------- Page: 2 ----------------------
ISO/IEC DISFDIS 24787-2:2022(E2024(en)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members
of ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC
Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives or
www.iec.ch/members_experts/refdocs).
Field Code Changed
Attention is drawnISO and IEC draw attention to the possibility that some of the elementsimplementation of
this document may beinvolve the subjectuse of (a) patent(s). ISO and IEC take no position concerning the
evidence, validity or applicability of any claimed patent rights. in respect thereof. As of the date of publication
of this document, ISO and IEC had not received notice of (a) patent(s) which may be required to implement
this document. However, implementers are cautioned that this may not represent the latest information,
which may be obtained from the patent database available at www.iso.org/patents and https://patents.iec.ch.
ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents) or the IEC list of patent declarations received (see
https://patents.iec.ch).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html. In the IEC, see www.iec.ch/understanding-
standardswww.iec.ch/understanding-standards.
This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and security devices for personal identification.
This first edition cancels and replaces ISO/IEC 24787:2018, which has been technically revised. ISO/IEC
24787 has been split into two parts, ISO/IEC 24787-1 and ISO/IEC 24787-2.
The main changes are as follows:
— — Previous Clause 9 “Work-sharing on-card biometric comparison procedure” and other subclauses
related to work-sharing have been moved into this document.
A list of all parts in the ISO/IEC 24787 series can be found on the ISO and IEC websites.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html and www.iec.ch/national-
committeeswww.iso.org/members.html and www.iec.ch/national-committees.
© ISO/IEC 2022 – All rights reserved 3
© ISO/IEC 2024 – All rights reserved
iii
---------------------- Page: 3 --------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.