ISO 3185:2008

Aerospace — Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions

ISO 3185:2008 specifies the dimensions of normal bihexagonal head bolts, with close or large tolerance normal shank and short or medium length MJ threads, in metallic material, coated or uncoated, with strength classes less than or equal to 1 100 MPa. ISO 3185:2008 is applicable to the compilation of aerospace product standards.

Aéronautique et espace — Vis à tête bihexagonale normale, avec tige normale et filetages MJ courts ou de longueur moyenne, en matériau métallique, revêtues ou non revêtues, des classes de résistance inférieures ou égales à 1 100 MPa — Dimensions

General Information

• Status: Withdrawn
• Publication Date: 17-Aug-2008
• Withdrawal Date: 17-Aug-2008
• ICS: 49.030.20 - Bolts, screws, studs
• Technical Committee: ISO/TC 20/SC 4 - Aerospace fastener systems
• Drafting Committee: ISO/TC 20/SC 4 - Aerospace fastener systems
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 30-Mar-2021

Relations

• Revised: ISO 3185:2021 - Aerospace — Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions
• Effective Date: 23-Apr-2020
• Revises: ISO 3185:1993 - Aerospace — Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions
• Effective Date: 15-Apr-2008
• Consolidated By: ISO 17233:2017 - Leather — Physical and mechanical tests — Determination of cold crack temperature of surface coatings
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3185
Second edition
2008-08-15


Aerospace — Bolts, normal bihexagonal
head, normal shank, short or medium
length MJ threads, metallic material,
coated or uncoated, strength classes less
than or equal to 1 100 MPa — Dimensions
Aéronautique et espace — Vis à tête bihexagonale normale, avec tige
normale et filetages MJ courts ou de longueur moyenne, en matériau
métallique, revêtues ou non revêtues, des classes de résistance
inférieures ou égales à 1 100 MPa — Dimensions




Reference number
ISO 3185:2008(E)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 3185:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3185:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3185 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 4,
Aerospace fastener systems.
This second edition cancels and replaces the first edition (ISO 3185:1993), which has been technically revised.

© ISO 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 3185:2008(E)

Aerospace — Bolts, normal bihexagonal head, normal shank,
short or medium length MJ threads, metallic material, coated or
uncoated, strength classes less than or equal to 1 100 MPa —
Dimensions
1 Scope
This International Standard specifies the dimensions of normal bihex
...