ISO/IEC 25045:2010

Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Evaluation module for recoverability

ISO/IEC 25045:2010 is one of the SQuaRE series of International Standards, which provides a framework for software products quality requirements and evaluation including the requirements for methods of software product measurement and evaluation. ISO/IEC 25045:2010 uses a methodology involving two types of evaluation for recoverability. One part of the method makes use of the disturbance injection methodology and a list of disturbances based on common categories of operational faults and events to evaluate the quality measure of resiliency. The second quality measure is based on a set of questions that is defined for each disturbance to evaluate the quality measure of autonomic recovery index by assessing how well the system detects, analyses, and resolves the disturbance without human intervention. ISO/IEC 25045:2010 is applicable to information systems executing transactions in a system supporting single or multiple concurrent users, where speedy recovery and ease of managing recovery is important to the acquirer, owner/operator, and the developer.

Ingénierie des systèmes et du logiciel — Exigences de qualité et évaluation des systèmes et du logiciel (SQuaRE) — Module d'évaluation pour la possibilité de récupération

General Information

• Status: Published
• Publication Date: 23-Aug-2010
• ICS: 35.080 - Software
• Technical Committee: ISO/IEC JTC 1/SC 7 - Software and systems engineering
• Drafting Committee: ISO/IEC JTC 1/SC 7/WG 6 - Software Product and System Quality
• Current Stage: 9020 - International Standard under periodical review
• Start Date: 15-Jan-2024
• Completion Date: 15-Jan-2024

Relations

• Consolidated By: ISO 6721-1:2011 - Plastics — Determination of dynamic mechanical properties — Part 1: General principles
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 25045
First edition
2010-09-01


Systems and software engineering —
Systems and software Quality
Requirements and Evaluation
(SQuaRE) — Evaluation module for
recoverability
Ingénierie des systèmes et du logiciel — Exigences de qualité et
évaluation des systèmes et du logiciel (SQuaRE) — Module
d'évaluation pour la possibilité de récupération




Reference number
ISO/IEC 25045:2010(E)
©
ISO/IEC 2010

---------------------- Page: 1 ----------------------
ISO/IEC 25045:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 25045:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
1.1 Characteristics.1
1.2 Level of evaluation .1
1.3 Technique.1
1.4 Applicability .2
2 Conformance .2
3 Normative references.2
4 Terms and definitions .3
5 Inputs and measures.3
5.1 Evaluation methodology.3
5.1.1 Practical considerations relating to the methodology .5
5.1.2 Disturbances.5
5.2 Input for the evaluation.8
5.2.1 The SUT description.8
5.2.2 The workload description.9
5.2.3 The fault load description.10
5.3 Data elements .
...