Ships and marine technology — Potable water supply on ships and marine structures — Part 2: Method of calculation

ISO 15748-2 applies to the planning, design and configuration of potable water supply systems on ships, stationary or floating marine structures and inland waterway crafts. It serves to determine the quantity of potable water to be carried on board, the capacity of the pressurized reservoirs and water heaters, the pumping capacity, etc.

Navires et techmologie maritime — Approvisionnement en eau potable sur navires et structures maritimes — Partie 2: Méthode de calcul

General Information

Status
Published
Publication Date
29-May-2002
Current Stage
9093 - International Standard confirmed
Completion Date
06-Jun-2024
Ref Project

Relations

Buy Standard

Standard
ISO 15748-2:2002 - Ships and marine technology -- Potable water supply on ships and marine structures
English language
40 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15748-2
First edition
2002-05-01

Ships and marine technology — Potable
water supply on ships and marine
structures —
Part 2:
Method of calculation
Navires et technologie maritime — Approvisionnement en eau potable sur
navires et structures maritimes —
Partie 2: Méthode de calcul




Reference number
ISO 15748-2:2002(E)
©
 ISO 2002

---------------------- Page: 1 ----------------------
ISO 15748-2:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 15748-2:2002(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references.1
3 Potable water consumption.2
4 Potable water storage .2
5 Determination and sizing of system components .2
6 Flow rates .3
7 Supply pressure.3
8 Generation and maintenance of pressure.3
9 Pipe diameters of distribution lines.4
10 Hot water requirements.5
11 Water heaters .5
12 Circulation lines and circulating pumps .6
13 Calculation example.6
Annex A (informative) Tables and figures with useful information .7
Annex B (informative) Form sheets for calculation.18
Annex C (informative) Calculation example .22
Annex D (informative) Information concerning the installation of sanitary facilities .38

© ISO 2002 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 15748-2:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of nationa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.