ISO/TS 16774-6:2024
(Main)Test methods for repair materials for water-leakage cracks in underground concrete structures — Part 6: Test method for response to the substrate movement
Test methods for repair materials for water-leakage cracks in underground concrete structures — Part 6: Test method for response to the substrate movement
This document specifies a laboratory test method for evaluating the substrate (crack) movement response of water-leakage crack repair materials through permeability testing. This document outlines general principles and procedures for the test method. Specific variables that control the quantifiable parameters of the testing are filled in using relevant national standards or testing parameters, or both.
Méthodes d'essai pour matériaux de réparation pour fissures dues à l'eau dans les structures en béton — Partie 6: Méthode d'essai de la réponse aux mouvements du substrat
General Information
Relations
Buy Standard
Standards Content (Sample)
Technical
Specification
ISO/TS 16774-6
Second edition
Test methods for repair materials
2024-08
for water-leakage cracks in
underground concrete structures —
Part 6:
Test method for response to the
substrate movement
Méthodes d'essai pour matériaux de réparation pour fissures
dues à l'eau dans les structures en béton —
Partie 6: Méthode d'essai de la réponse aux mouvements du
substrat
Reference number
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative reference . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Preparation . 2
6.1 Test specimen and artificial crack conditions .2
6.2 Ambient conditions.3
7 Procedure . 3
7.1 Substrate behaviour stress test .3
7.2 Permeability test .3
8 Presentation of results . 3
9 Test report . 4
9.1 Information on the repair material of the test target .4
9.1.1 General .4
9.1.2 Other information .4
9.2 Information on the test .4
Annex A (informative) Example test method . 6
Bibliography .16
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 71, Concrete, reinforced concrete and pre-
stressed concrete, Subcommittee SC 7, Maintenance and repair of concrete structures.
This second edition cancels and replaces the first edition (ISO/TS 16774-6:2017), which has been technically
revised.
The main changes are as follows:
— in 6.1 a), a recommendation regarding the specification of the fine aggregate, as well as the necessary
reference to the relevant standard, has been added;
— in 6.1 d), the text has been revised to provide clearer context.
A list of all parts in the ISO/TS 16774 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
This document is linked to ISO/TR 16475. ISO/TR 16475 outlines six basic properties and the required
performance levels of water-leakage repair materials; The ISO/TS 16774 series proposes sample testing
methods for evaluating the respective properties of the repair materials.
The test methods in this document are intended to serve as reference for nations that have not yet
developed a test method for the six required performance properties of water-leakage repair materials.
Many of the dependent variables outlined in the reference test methods of this document are subject to
change in accordance with the environmental conditions (temperature and humidity, chemical solution
and concentration, width of movement activity, water pressure or water flow velocity, etc.) outlined in the
standards used in respective countries.
In this document, ISO/TS 16774-1 and ISO/TS 16774-5, for the purpose of objectively comparing the
performance of injected repair materials, artificial cracks of same width, height, and volume are used to
control the usage of repair materials for each testing cycle and enable repetition of the same test methods
under the same conditions.
The repair material injected into a test specimen with an artificial crack undergoes simulated movements
normally caused by thermal expansion, settlement and vibrations in leakage cracks found in concrete
structures outlined in different national testing parameters that reflect different environmental
conditions. As such, the results are only intended to provide a comparative performance evaluation of the
waterproofing repair materials between different products of the same type of repair material under the
same environmental conditions.
NOTE 1 The test method in this document classifies and categorizes materials that are tested into families of
similar properties for the purpose of making relative comparisons with the data results.
NOTE 2 Each individual repair material can be further tested in an actual construction site application for a
complete assessment.
v
Technical Specification ISO/TS 16774-6:2024(en)
Test methods for repair materials for water-leakage cracks in
underground concrete structures —
Part 6:
Test method for response to the substrate movement
1 Scope
This document specifies a laboratory test method for evaluating the substrate (crack) movement response
of water-leakage crack repair materials through permeability testing.
This document outlines general principles and procedures for the test method. Specific variables that
control the quantifiable parameters of the testing are filled in using relevant national standards or testing
parameters, or both.
2 Normative reference
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO/TR 16475, General practices for the repair of water-leakage cracks in concrete structures
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/TR 16475 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— IEC Electropedia: available at https:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org .obp
3.1
repair material
material used for preventing the escape of water at cracks in concrete
EXAMPLE Injection type grouts, such as synthetic rubberized asphalt, mastic, urethane, poly-urea.
Note 1 to entry: In this document, target ingredients are limited to injection materials outlined in ISO/TR 16475.
4 Principle
Response to loss, deterioration and other physical changes by the behavioral movement of leakage crack
(such as crack movements caused by thermal shrinkage and expansions, differential settlement, and/or
vibrations) is one of the fundamental properties that water leakage repair materials should possess. To
evaluate the repair material’s responsiveness to substrate movement, this test method uses two separate
procedures:
a) a substrate movement test method;
a) a permeability test method.
The test specimen with an artificial crack is injected with repair material, and the specimen goes through
an induced tensile/compressive stress test for a specified number of cycles using a substrate movement
simulating apparatus, such as a universal testing machine (UTM). To evaluate whether the repair material
loses its waterproofing property due to tensile/compressive stress (substrate/crack movement), the
specimen goes through a water permeability test for the last stage of the test method.
5 Apparatus
5.1 Substrate movement apparatus, which must be able to exert a cycle of predetermined width of
compressive and tensile force per one minute. A universal testing machine (UTM) should be used for this
test method.
5.2 Air compressor, which should be able to handle a minimum air pressure value of 0,1 N/mm to
0,3 N/mm .
5.3 Permeability test chamber, which should be able to handle a minimum water pressure value of
2 2
0,1 N/mm to 0,3 N/mm (output method).
NOTE Conditions outlined in 5.2 and 5.3 are subject to change in accordance to different national testing
parameters and requirements.
6 Preparation
6.1 Test specimen and artificial crack conditions
a) Two separate concrete or mortar substrate parts should be cured to form a water-leakage crack test
specimen. The parts consist of upper and bottom parts,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.