ISO/IEC 14443-1:2008/Amd 1:2012
(Amendment)Identification cards — Contactless integrated circuit cards — Proximity cards — Part 1: Physical characteristics — Amendment 1: Additional PICC classes
Identification cards — Contactless integrated circuit cards — Proximity cards — Part 1: Physical characteristics — Amendment 1: Additional PICC classes
Cartes d'identification — Cartes à circuit(s) intégré(s) sans contact — Cartes de proximité — Partie 1: Caractéristiques physiques — Amendement 1: Classes de PICC additionnelles
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 14443-1
Second edition
2008-06-15
AMENDMENT 1
2012-05-01
Identification cards — Contactless
integrated circuit cards — Proximity
cards —
Part 1:
Physical characteristics
AMENDMENT 1: Additional PICC classes
Cartes d'identification — Cartes à circuit(s) intégré(s) sans contact —
Cartes de proximité —
Partie 1: Caractéristiques physiques
AMENDEMENT 1: Classes de PICC additionnelles
Reference number
ISO/IEC 14443-1:2008/Amd.1:2012(E)
©
ISO/IEC 2012
---------------------- Page: 1 ----------------------
ISO/IEC 14443-1:2008/Amd.1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 14443-1:2008/Amd.1:2012(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO/IEC 14443-1:2008 was prepared by Joint Technical Committee ISO/IEC JTC 1,
Information technology, Subcommittee SC 17, Cards and personal identification.
© ISO/IEC 2012 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 14443-1:2008/Amd.1:2012(E)
Identification cards — Contactless integrated circuit cards —
Proximity cards —
Part 1:
Physical characteristics
AMENDMENT 1: Additional PICC classes
Page 1, Normative references
Replace “ISO/IEC 10373-6” with “ISO/IEC 10373-6:2011”.
Add the following normative reference:
“ISO/IEC 14443-2, Identification cards — Contactless integrated circuit cards — Proximity cards — Part 2:
Radio frequency power and signal interface”
Page 2, 4.4
Replace the paragraph with the following:
“If the PICC meets the requirements of one particular class as specified in Annex A, then the PICC, whichever
form the PICC has according to 4.1, shall continue to operate as intended after continuous exposure
to a magnetic field of an average level of 4/3 times H at 13,56 MHz as specified in
max
1)
ISO/IEC 14443-2:2010/Amd.2:— , 6.2 for this class. The averaging time is 30 seconds and the maximum
level of the magnetic field is limited to 8/5 times H .
max
If the PICC does not claim to meet the requirements of one particular class as specified in Annex A, then the
PICC, whichever form the PICC has according to 4.1, shall continue to operate as intended after continuous
exposure to a magnetic field of an average level of 10 A/m (rms) at 13,56 MHz. The averaging time is 30
seconds and the maximum level of the magnetic field is limited to 12 A/m (rms).”
Page 3, Annex A
Replace Annex A with the following:
1)
To be published.
© ISO/IEC 2012 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO/IEC 14443-1:2008/Amd.1:2012(E)
Annex A
(normative)
PICC class definitions
A.1 “Class 1”
A “Class 1” PICC shall fulfil the requirements in A.1.1 and A.1.2. The support of “Class 1” PICCs is mandatory
for PCDs.
A.1.1 Antenna location
The antenna of a “Class 1” PICC shall be located within a zone defined by two rectangles, as specified in
Figure A.1:
external rectangle: 81 mm 49 mm;
internal rectangle: 64 mm 34 mm, centered in the external rectangle, with 3 mm corner radii;
2
except for the connections to the ends of the antenna coil, with a maximum area of 300 mm .
81 mm
64 mm
PICC antenna zone R 3 mm
Figure A.1 — Location of the antenna of the “Class 1” PICC
The antenna of a PICC with ID-1 dimensions
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.