ISO 13414:1997

Aerospace — Airframe needle roller bearings, single-row, shielded — Inch series

Aéronautique et espace — Roulements à aiguilles, à une rangée, avec flasques, pour cellule d'aéronef — Série "inch"

General Information

• Status: Withdrawn
• Publication Date: 24-Dec-1997
• ICS: 49.035 - Components for aerospace construction
• Technical Committee: ISO/TC 20 - Aircraft and space vehicles
• Drafting Committee: ISO/TC 20 - Aircraft and space vehicles
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 12-Jul-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13414
First edition
1997-12-15
Aerospace — Airframe needle roller
bearings, single-row, shielded — Inch
series
Aéronautique et espace — Roulements à aiguilles, à une rangée, avec
flasques, pour cellule d'aéronef — Série «inch»
A
Reference number
ISO 13414:1997(E)

---------------------- Page: 1 ----------------------
ISO 13414:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 13414 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles,
Subcommittee SC 15, Airframe bearings.
Annex A of this International Standard is for information only.
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 2 ----------------------
©
ISO ISO 13414:1997(E)
Introduction
At the time this International Standard was developed, the Imperial units sizes of airframe needle roller bearings were
dominant in world application. The basis for this International Standard is the imperial units provided in annex A.
iii

---------------------- Page: 3 ----------------------
©
INTERNATIONAL STANDARD  ISO ISO 13414:1997(E)
Aerospace — Airframe needle roller bearings, single-row,
shielded— Inch series
1 Scope
This International Standard specifies the characteristics, boundary dimensions, tolerances, internal clearances and
permissible static radial loads of inch series, single-row, needle roller bearings used in airframe applications.
The airframe needle roller bearings covered by this International Standard are designed to operate in the temperature
range –54 °C to +121 °C.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility
of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of
currently valid International Standards.
1)
ISO 683-17:— , Heat-treated steels, alloy steels and free-cutting steels — Part 17: Ball and roller bearing steels.
ISO 1132:1980, Rolling bearings — Tolerances — Definitions.
ISO 2082:1986, Metallic coatings — Electroplated coatings of cadmium on iron or steel.
ISO 4520:1981, Chromate conversion coatings on electroplated zinc and cadmium coatings.
ISO 5593:1997, Rolling bearings — Vocabulary.
ISO 6158:1984, Metallic coatings — Electroplated coatings of chromium for engineering purposes.
ISO 13411:1997, Aerospace — Airframe needle roller, cylindrical roller and track roller bearings — Technical
specification.
2)
AMS 2417E:1993, Plating, zinc-nickel alloy.
3 Definitions
For the purposes of this International Standard, the definitions given in ISO 5593 apply.
4 Symbols
4.1  For the purposes of this International Standard, the symbols given in ISO 1132 apply. The symbols (except those
for tolerances) shown in the figures and the values given in the tables denote nominal dimensions unless specified
otherwise.

1)
 To be published. (Revision of ISO 683-17:1976)
2)
Available from: SAE International
400 Commonwealth Drive
Warrendale, PA 15096-0001
USA
1

---------------------- Page: 4 ----------------------
©
ISO 13414:1997(E) ISO
4.2  The following additional symbols for bearings covered by this International Standard also apply.
B overall width (over faces of end washers)

C permissible static radial load
s
d clamping face diameter
a
5 Required characteristics
5.1 Dimensions — Tolerances — Internal clearances — Loads
For values, see table 1. For configuration, see figure 1.
Table 1
Dimensions in millimetres,
tolerance and clearance values in micrometres
dD B C r d C
s a s
Tolerance values Internal clearance Mass
Diameter
code
0 0
D K D
Radial, G Axial, G
dmp ia Dmp
r a
- 127 - 127
kg
max. min. min. min. max. max. kN »
03 4,826 17,463 7,93 5,54 11,2 8 0,01
05 6,35 19,05 9,53 7,14 13,2 8 43 12,7 0,02
0,55
05 7,938 20,638 11,1 8,74 14,7 18,1 0,03
06 9,525 22,225 14,28 11,92 16,3 28,1 0,03
07 11,113 23,813 15,88 13,49 17,9 10 46 35,5 0,04
 0
08 12,7 28,575 19,05 16,67 21,5 51,5 0,08
- 13
09 14,288 30,163 22,23 19,84 22,7 66,7 0,09
10 15,875 31,75 25,4
...