ISO 7010:2011/Amd 6:2014
(Amendment)Graphical symbols — Safety colours and safety signs — Registered safety signs — Amendment 6
Graphical symbols — Safety colours and safety signs — Registered safety signs — Amendment 6
Symboles graphiques — Couleurs de sécurité et signaux de sécurité — Signaux de sécurité enregistrés — Amendement 6
General Information
RELATIONS
Standards Content (sample)
INTERNATIONAL ISO
STANDARD 7010
Second edition
2011-06-01
AMENDMENT 6
2014-12-15
Graphical symbols — Safety colours
and safety signs — Registered safety
signs
AMENDMENT 6
Symboles graphiques — Couleurs de sécurité et signaux de sécurité —
Signaux de sécurité enregistrés
AMENDEMENT 6
Reference number
ISO 7010:2011/Amd.6:2014(E)
ISO 2014
---------------------- Page: 1 ----------------------
ISO 7010:2011/Amd.6:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7010:2011/Amd.6:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 145, Graphical symbols, Subcommittee SC 2,
Safety identification, signs, shapes, symbols and colours.© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 7010:2011/Amd.6:2014(E)
Graphical symbols — Safety colours and safety signs —
Registered safety signs
AMENDMENT 6
IMPORTANT — The colours represented in the electronic file of this International Standard can
be neither viewed on screen nor printed as true representations. Al...
NORME ISO
INTERNATIONALE 7010
Deuxième édition
2011-06-01
AMENDEMENT 6
2014-12-15
Symboles graphiques — Couleurs
de sécurité et signaux de sécurité —
Signaux de sécurité enregistrés
AMENDEMENT 6
Graphical symbols — Safety colours and safety signs — Registered
safety signs
AMENDMENT 6
Numéro de référence
ISO 7010:2011/Amd.6:2014(F)
ISO 2014
---------------------- Page: 1 ----------------------
ISO 7010:2011/Amd.6:2014(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2014
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2014 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO FDIS 7010:2011 Amd 6:2014
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le
droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails
concernant les références aux droits de propriété intellectuelle ou autres droits analogues identifiés
lors de l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations
de brevets reçues par l'ISO (voir www.iso.org/brevets).Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.Pour une explication de la signification des termes et expressions spécifiques de l'ISO liés à l'évaluation
de la conformité, ou pour toute information au sujet de l'adhésion de l'ISO aux principes de l'OMC
concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant‐propos —
Informations supplémentaires.Le comité chargé de l'élaboration du présent document est l'ISO/TC 145, Symboles graphiques et
pictogrammes, Sous-comité 2, Identification de sécurité, signaux, formes, symboles et couleurs.
iii© ISO 2014 – Tous droits réservés
---------------------- Page: 3 ----------------------
Projet de norme internationale ISO FDIS 7010:2011 Amd 6:2014
Symboles graphiques — Couleurs de sécurité et signaux de
sécurité — Signaux de sécurité enregistrés — Amendement 6
IMPORTANT — Les couleurs représentées dans le fichier électronique de la présente Norme
internationale ne peuvent être considérées comme rep...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.