ISO 2773
(Main)Test conditions for pillar type vertical drilling machines — Testing of accuracy
Test conditions for pillar type vertical drilling machines — Testing of accuracy
Conditions d'essais des machines à percer verticales à colonne — Contrôle de l’exactitude
General Information
Relations
Buy Standard
Standards Content (Sample)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 2773
ISO/TC 39/SC 2
Test conditions for pillar type vertical
Secretariat: ASI
drilling machines — Testing of the
Voting begins on:
2023-08-31 accuracy
Voting terminates on:
Conditions d'essais des machines à percer verticales à colonne —
2023-10-26
Contrôle de l’exactitude
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 2773:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 1 ----------------------
ISO/FDIS 2773:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 2773
ISO/TC 39/SC 2
Test conditions for pillar type vertical
Secretariat: ASI
drilling machines — Testing of the
Voting begins on:
accuracy
Voting terminates on:
Conditions d'essais des machines à percer verticales à colonne —
Contrôle de l’exactitude
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 2773:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 2 ----------------------
ISO/FDIS 2773:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Terminology, designation of axes and machine configurations. 1
5 Preliminary remarks . 2
5.1 Measurement units . 2
5.2 Reference to ISO 2301, ISO 2307 and ISO/TR 23011 . 3
5.3 Testing sequence . 3
5.4 Test to be performed . 3
5.5 Measuring instruments . 3
5.6 Minimum tolerance
...
ISO/FDIS 2773:2023(E)
ISO TC 39/SC 02
Secretariat: ASI
Test conditions for pillar type vertical drilling machines — Testing of the accuracy
Conditions d'essais des machines à percer verticales à colonne — Contrôle de la précision
First edition
Date: 20222023-08-0916
---------------------- Page: 1 ----------------------
ISO/FDIS 2773:2023(E)
© ISO 2022 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no
part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet, without
prior written permission. Permission can be requested from either ISO at the address below or
ISO's member body in the country of the requester.
ISO Copyright Office
CP 401 • CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland.
ii © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 2773:2023(E)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Terminology, designation of axes and machine configurations . 2
5 Preliminary remarks . 3
5.1 Measurement units . 3
5.2 Reference to ISO 230-1, ISO 230-7 and ISO/TR 230-11 . 3
5.3 Testing sequence . 3
5.4 Test to be performed . 3
5.5 Measuring instruments . 3
5.6 Minimum tolerance . 3
5.7 Levelling . 3
6 Test conditions and permissible deviations . 4
6.1 Table . 4
6.2 Spindle (Quill) . 6
6.3 Spindle head . 9
Annex A (informative) Terms in other languages . 10
Bibliography . 11
© ISO 2023 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/FDIS 2773:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In partic
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.