ISO/FDIS 182-3
(Main)Plastics — Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures — Part 3: Conductometric method
Plastics — Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures — Part 3: Conductometric method
This document specifies a method for the determination of the thermal stability at elevated temperature of compounds and products based on vinyl chloride homopolymers and copolymers (in the following text abbreviated as PVC) which undergo dehydrochlorination (the evolution of hydrogen chloride). This document is applicable to the characterization of PVC compounds and products, especially with regard to the effectiveness of their heat-stabilizing systems. It is applicable to coloured PVC compounds and products where a discolouration test under the action of heat may be unsatisfactory. This document is applicable to compounded PVC materials and products. It can be applicable to polymers in powder form under appropriate conditions, to be agreed upon between the interested parties. This document does not apply to PVC compounds in the form of dry blends, since such materials can be not sufficiently homogeneous. This document does not apply to PVC compounds and products which evolve other decomposition products, in addition to hydrogen chloride, at elevated temperatures that can affect the conductivity of water when they are absorbed into it. In this case, a method suitable for the determination of chloride ion (Cl−) in the absorbing solution shall be used (see ISO 182-4[2]). This document can also be applied to other plastics materials which can evolve hydrogen chloride or other hydrogen halides when heated under the conditions prescribed by the relevant specifications, or as agreed upon between the interested parties.
Plastiques — Détermination de la tendance des compositions et produits à base d’homopolymères et de copolymères du chlorure de vinyle à dégager du chlorure d’hydrogène et éventuellement d’autres produits acides à températures élevées — Partie 3: Méthode conductimétrique
Le présent document spécifie une méthode pour la détermination de la stabilité thermique à températures élevées des compositions et produits à base d’homopolymères et de copolymères du chlorure de vinyle (PVC dans le texte qui suit), qui sont sujets à une déhydrochloruration (dégagement de chlorure d’hydrogène). Le présent document s’applique à la caractérisation des compositions et produits à base de PVC, en particulier en ce qui concerne l’efficacité de leurs systèmes de stabilisation à la chaleur. Il est applicable aux compositions et produits à base de PVC colorés, lorsqu’un essai de décoloration sous l’action de la chaleur peut être insatisfaisant. Le présent document est applicable aux matériaux et produits composés de PVC. Il peut être applicable aux polymères sous forme de poudres dans des conditions appropriées devant faire l’objet d’un accord entre les parties intéressées. Le présent document ne s’applique pas aux compositions de PVC sous forme de mélanges secs, ces matériaux pouvant ne pas être suffisamment homogénéisés. Le présent document ne s’applique pas aux compositions et produits à base de PVC qui dégagent, à températures élevées, des produits de décomposition en plus du chlorure d’hydrogène pouvant avoir une incidence sur la conductivité de l’eau lorsqu’ils y sont absorbés. Dans ce cas, une méthode appropriée pour la détermination des ions chlorures (Cl−) dans la solution absorbante doit être employée (voir l’ISO 182-4[2]). Le présent document peut aussi être appliqué à d’autres matériaux plastiques pouvant dégager du chlorure d’hydrogène ou d’autres halogénures d’hydrogène lorsqu’ils sont chauffés dans des conditions particulières prescrites dans les spécifications appropriées ou convenues entre les parties intéressées.
General Information
Relations
Standards Content (Sample)
FINAL DRAFT
International
Standard
ISO/TC 61/SC 9
Plastics — Determination of
Secretariat: KATS
the tendency of compounds and
Voting begins on:
products based on vinyl chloride
homopolymers and copolymers to
Voting terminates on:
evolve hydrogen chloride and any
other acidic products at elevated
temperatures —
Part 3:
Conductometric method
Plastiques — Détermination de la tendance des compositions et
produits à base d’homopolymères et de copolymères du chlorure
de vinyle à dégager du chlorure d’hydrogène et éventuellement
d’autres produits acides à températures élevées —
Partie 3: Méthode conductimétrique
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
FINAL DRAFT
International
Standard
ISO/TC 61/SC 9
Plastics — Determination of
Secretariat: KATS
the tendency of compounds and
Voting begins on:
products based on vinyl chloride
homopolymers and copolymers to
Voting terminates on:
evolve hydrogen chloride and any
other acidic products at elevated
temperatures —
Part 3:
Conductometric method
Plastiques — Détermination de la tendance des compositions et
produits à base d’homopolymères et de copolymères du chlorure
de vinyle à dégager du chlorure d’hydrogène et éventuellement
d’autres produits acides à températures élevées —
Partie 3: Méthode conductimétrique
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Principle . 2
5 Reagents . 2
6 Apparatus . 2
7 Preparation of test samples . 7
7.1 General .7
7.2 PVC plastisols . .7
7.3 PVC pellets, extrudates, mouldings, thick sheet, etc. .7
7.4 PVC film and sheet .7
7.5 PVC coatings .7
7.6 Cable and conductor insulation or sheating .7
8 Number of tests . 7
9 Temperatures for dehydrochlorination . 7
10 Test procedure . 8
10.1 Preparation of test portion .8
10.2 Preliminary operations .8
10.3 Special precautions when using dehydrochlorination cell A .8
10.4 Preparation of the measurement cell .8
10.5 Decomposition of the test portion .8
11 Expression of results . 9
12 Test report . 9
13 Precision . 9
13.1 General .9
13.2 Repeatability .10
13.3 Reproducibility .10
13.4 Comparison with the pH-meter method (ISO 182-2) .10
13.5 Factors affecting the stability time .10
13.6 Conclusions . 12
Annex A (informative) Cleaning of the apparatus .13
Annex B (informative) Calculation of repeatability and reproducibility — Conductometric and
pH-meter methods . 14
Annex C (informative) Interlaboratory test.16
Bibliography .18
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials, in collaboration with the European Committee for Standardization (CEN) Technical Committee
CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 182-3:2023), which has been editorial revised.
The main changes are as follows:
— the reference to ISO 182-4 in the Scope has been placed in a Note;
— the unit min has been added to to m, r, and R in Clause 13;
— the code for stability time in Table 1 has been corrected to t ;
s
— the unit of t in Table 2 has been corrected to min.
s
A list of all parts in the ISO 182 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
FINAL DRAFT International Standard ISO/FDIS 182-3:2025(en)
Plastics — Determination of the tendency of compounds
and products based on vinyl chloride homopolymers and
copolymers to evolve hydrogen chloride and any other acidic
products at elevated temperatures —
Part 3:
Conductometric method
WARNING — The use of this document can involve hazardous materials, operations and equipment.
This document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and
determine the applicability of regulatory limitations prior to use.
1 Scope
1.1 This document specifies a method for the determination of the thermal stability at elevated
temperature of compounds and products based on vinyl chloride homopo
...
Second edition
2023-12
ISO/TC 61/SC 9
Secretariat: KATS
Date: 2025-07-03
Plastics — Determination of the tendency of compounds and
products based on vinyl chloride homopolymers and copolymers to
evolve hydrogen chloride and any other acidic products at elevated
temperatures —
Part 3:
Conductometric method
Plastiques — Détermination de la tendance des compositions et produits à base d’homopolymères et de
copolymères du chlorure de vinyle à dégager du chlorure d’hydrogène et éventuellement d’autres produits
acides à températures élevées —
Partie 3: Méthode conductimétrique
FDIS stage
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 20232025 – All rights reserved
ii
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Principle . 2
5 Reagents . 2
6 Apparatus . 2
7 Preparation of test samples . 7
7.1 General . 7
7.2 PVC plastisols . 7
7.3 PVC pellets, extrudates, mouldings, thick sheet, etc. . 7
7.4 PVC film and sheet . 7
7.5 PVC coatings . 7
7.6 Cable and conductor insulation or sheating . 7
8 Number of tests . 7
9 Temperatures for dehydrochlorination . 7
10 Test procedure . 8
10.1 Preparation of test portion . 8
10.2 Preliminary operations . 8
10.3 Special precautions when using dehydrochlorination cell A . 8
10.4 Preparation of the measurement cell . 8
10.5 Decomposition of the test portion . 8
11 Expression of results . 9
12 Test report . 9
13 Precision . 9
13.1 General . 9
13.2 Repeatability .10
13.3 Reproducibility .10
13.4 Comparison with the pH-meter method (ISO 182-2) .10
13.5 Factors affecting the stability time .10
13.6 Conclusions .12
Annex A (informative) Cleaning of the apparatus .13
Annex B (informative) Calculation of repeatability and reproducibility — Conductometric and
pH‑meter methods .14
Annex C (informative) Interlaboratory test .16
Bibliography .18
Foreword . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
iii
4 Principle . 2
5 Reagents . 2
6 Apparatus . 2
7 Preparation of test samples . 10
8 Number of tests . 11
9 Temperatures for dehydrochlorination . 11
10 Test procedure . 11
11 Expression of results . 12
12 Test report . 12
13 Precision . 13
Annex A (informative) Cleaning of the apparatus . 17
Annex B (informative) Calculation of repeatability and reproducibility — Conductometric and
pH‑meter methods . 18
Annex C (informative) Interlaboratory test . 20
Bibliography . 22
iv © ISO 20232025 – All rights reserved
iv
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials, in collaboration with the European Committee for Standardization (CEN) Technical Committee
CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 182-3:2023), which has been editorial revised.
The main changes are as follows:
— Adjust the reference to ISO 182-4 referenced in the Scope 1.4 to has been placed in a Note;
— Added the unit min has been added to to m, r, and R in Chapter 13.13;
— Correct the code for Stabilitystability time in Table 1Table 1 has been corrected to t .;
s
— Correct the unit of t in Table 2Table 2 has been corrected to min.
s
—
A list of all parts in the ISO 182 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
Plastics — Determination of the tendency of compounds and products
based on vinyl chloride homopolymers and copolymers to evolve
hydrogen chloride and any other acidic products at elevated
temperatures —
Part 3:
Conductometric method
WARNING — The use of this document can involve hazardous materials, operations and equipment.
This document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and
determine the applicability of regulatory limitations prior to use.
1 Scope
1.1 1.1 This document specifies a method for the determination of the thermal stability at elevated
temperature of compounds and products based on vinyl chloride homopolymers and copolymers (in the
following text abbreviated as PVC) which undergo dehydrochlorination (the evolution of hydrogen chloride).
1.2 1.2 This document is applicable to the characterization of PVC compounds and products, especially
with regard to the effectiveness of their he
...
PROJET FINAL
Norme
internationale
ISO/TC 61/SC 9
Plastiques — Détermination de
Secrétariat: KATS
la tendance des compositions et
Début de vote:
produits à base d’homopolymères
et de copolymères du chlorure
Vote clos le:
de vinyle à dégager du chlorure
d’hydrogène et éventuellement
d’autres produits acides à
températures élevées —
Partie 3:
Méthode conductimétrique
Plastics — Determination of the tendency of compounds and
products based on vinyl chloride homopolymers and copolymers
to evolve hydrogen chloride and any other acidic products at
elevated temperatures —
Part 3: Conductometric method
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
PROJET FINAL
Norme
internationale
ISO/TC 61/SC 9
Plastiques — Détermination de
Secrétariat: KATS
la tendance des compositions et
Début de vote:
produits à base d’homopolymères
et de copolymères du chlorure
Vote clos le:
de vinyle à dégager du chlorure
d’hydrogène et éventuellement
d’autres produits acides à
températures élevées —
Partie 3:
Méthode conductimétrique
Plastics — Determination of the tendency of compounds and
products based on vinyl chloride homopolymers and copolymers
to evolve hydrogen chloride and any other acidic products at
elevated temperatures —
Part 3: Conductometric method
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
© ISO 2025 INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
NORMES POUVANT
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse Numéro de référence
ii
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 2
3 Termes et définitions . 2
4 Principe. 2
5 Réactifs . 2
6 Appareillage . 2
7 Préparation des échantillons pour essai . 7
7.1 Généralités .7
7.2 Plastisols de PVC .7
7.3 Granulés de PVC, extrudats, pièces moulées, plaques épaisses, etc .7
7.4 Films et feuilles de PVC .7
7.5 Revêtements de PVC .7
7.6 Isolation et revêtements de câbles et de conducteurs .7
8 Nombre d’essais . 7
9 Températures pour la déhydrochloruration . 8
10 Mode opératoire d’essai . 8
10.1 Préparation de la prise d’essai.8
10.2 Opérations préliminaires .8
10.3 Précautions spéciales lors de l’utilisation de la cellule de déhydrochloruration A .8
10.4 Préparation de la cellule de mesure .8
10.5 Décomposition de la prise d’essai .9
11 Expression des résultats . 9
12 Rapport d’essai . 9
13 Fidélité . 9
13.1 Généralités .9
13.2 Répétabilité .10
13.3 Reproductibilité .10
13.4 Comparaison avec la méthode au pH-mètre (ISO 182-2) .10
13.5 Facteurs ayant une incidence sur le temps de stabilité .10
13.6 Conclusions . 13
Annexe A (informative) Nettoyage de l’appareillage . 14
Annexe B (informative) Calcul de la répétabilité et de la reproductibilité — Méthode
conductimétrique et méthode au pH-mètre .15
Annexe C (informative) Essai interlaboratoires . 17
Bibliographie . 19
iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n'avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l'adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de propriété.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 9, Matériaux
thermoplastiques, en collaboration avec le comité technique CEN/TC 249, Plastiques, du Comité européen de
normalisation (CEN) conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord de
Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 182-3:2023), qui a fait l’objet d’une
révision éditoriale.
Les principales modifications sont les suivantes:
— dans le Domaine d’application, la référence à l’ISO 182-4 a été mise dans une Note;
— l'unité min a été ajoutée à m, r et R à l'Article 13;
— dans le Tableau 1, le sigle utilisé pour le temps de stabilité a été modifié en t ;
s
— dans le Tableau 2, l’unité de t a été modifié en min.
s
Une liste de toutes les parties de la série ISO 182 est disponible sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/fr/members.html.
iv
PROJET FINAL Norme internationale ISO/FDIS 182-3:2025(fr)
Plastiques — Détermination de la tendance des compositions
et produits à base d’homopolymères et de copolymères du
chlorure de vinyle à dégager du chlorure d’hydrogène et
éventuellement d’autres produits acides à températures
élevées —
Partie 3:
Méthode conductimétrique
AVERTISSEMENT — L’utilisation du
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.