ISO/TR 20572:2007
(Main)Footwear — Performance requirements for components for footwear — Accessories
Footwear — Performance requirements for components for footwear — Accessories
ISO/TR 20572:2007 establishes the performance requirements for accessories (laces and eyelets, metal components and touch and close fasteners) for footwear (not for finished footwear), irrespective of the material, in order to assess the suitability for the end use. It also establishes the test methods to be used to evaluate the compliance with the requirements. This Technical Report applies to accessories (laces and eyelets, metal components and touch and close fasteners) for various kinds of footwear. ISO/TR 20572:2007 is intended to be used as a reference between the manufacturer and the supplier.
Chaussures — Exigences de performance pour les composants des chaussures — Accessoires
General Information
Relations
Standards Content (Sample)
TECHNICAL ISO/TR
REPORT 20572
First edition
2007-02-15
Footwear — Performance requirements
for components for footwear —
Accessories
Chaussures — Exigences de performance pour les composants des
chaussures — Accessoires
Reference number
ISO/TR 20572:2007(E)
©
ISO 2007
---------------------- Page: 1 ----------------------
ISO/TR 20572:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TR 20572:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In exceptional circumstances, when a technical committee has collected data of a different kind from that
which is normally published as an International Standard (“state of the art”, for example), it may decide by a
simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely
informative in nature and does not have to be reviewed until the data it provides are considered to be no
longer valid or useful.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TR 20572 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 309, Footwear, in collaboration with Technical Committee ISO/TC 216, Footwear, in accordance with
the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
TECHNICAL REPORT ISO/TR 20572:2007(E)
Footwear — Performance requirements for components for
footwear — Accessories
1 Scope
This Technical Report establishes the performance requirements for accessories (laces and eyelets, metal
components and touch and close fasteners) for footwear (not for finished footwear), irrespective of the
material, in order to assess the suitability for the end use. It also establishes the test methods to be used to
evaluate the compliance with the requirements.
This Technical Report applies to accessories (laces and eyelets, metal components and touch and close
fasteners) for all kind of footwear as defined in Clause 3.
This Technical Report is intended to be used as a reference between the manufacturer and the supplier. It is
not intended for third party certification of finished shoes destined for the consumer.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 31-0, Quantities and units — Part 0: General principle
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.