Airport Collaborative Decision Making (A-CDM) - Community Specification for application under the Single European Sky Interoperability Regulation EC 552/2004

The present document is applicable to Air Traffic Management Airport Collaborative Decision Making (A-CDM). The present document addresses the specific roles, responsibilities, procedures, systems and interfaces needed to fulfil the Airport CDM (A-CDM) Operating Concept as requested by Mandate M/390 of the European Commission. It references existing documentation where necessary to clarify the more detailed aspects of a procedure or system implementation requirement to avoid unnecessary repetition. Airport Collaborative Decision making (A-CDM) is about improving the way operational partners at airports and European ATFCM (Air Traffic Flow and Capacity Management, Air Traffic Control, Airlines, Ground Handling Agents/Units and Airports) work together at an operational level. A-CDM allows an Airport CDM partner to make the right decisions for a flight during the whole Airport CDM process in collaboration with other Airport CDM partners, knowing their preferences and constraints and the actual and predicted situation. The decision making by the Airport CDM partners is dependent upon the sharing of accurate and timely information and upon adapted Airport CDM procedures, mechanisms and tools. Any software elements related to the software assurance level of an A-CDM System are outside of the scope of the present document. As such the essential requirements of the Interoperability Regulation are not considered for software elements within the present document. The present document does not give a presumption of conformity related to maintenance requirements, safety, civil/military coordination or environmental constraints. NOTE: For these ERs, please refer to the Air Navigation Service Provider procedures. Requirements in the present document which refer to "should" statements or recommendations in the normatively referenced material (clause 2.1) are to be interpreted as fully normative ("shall") for the purpose of compliance with the present document.

Sodelovalno odločanje na letališčih (A-CDM) - Specifikacija Skupnosti v Uredbi EC 552/2004 o medobratovalnosti na enotnem evropskem nebu

Pričujoči dokument velja za sodelovalno odločanje na letališčih za nadzor zračnega prometa (a-CDM). Pričujoči dokument naslavlja določene vloge, odgovornosti, postopke, sisteme in vmesnike, potrebne za izpolnitev letališkega CDM (A-CDM) koncepta delovanja, kot je zahtevano z mandatom M/390 Evropske komisije. Naslavlja obstoječo dokumentacijo, kadar je potrebno, da pojasni bolj podrobne vidike postopka ali zahtevo implementacije sistema, z namenom izogniti se nepotrebnim ponavljanjem. Sodelovalno odločanje na letališčih (A-CDM) izboljšuje način, kako poslovni partnerji na letališčih in evropski ATFCM (upravljanje toka zračnega prometa in zmogljivosti, kontrola zračnega prometa, letalske družbe, agenti na tleh/enote in letališča) delajo skupaj na ravni delovanja. A-CDM dopušča CDM partnerju letališča, da izbira pravilne odločitve za let med celotnim CDM procesom letališča, v sodelovanju z ostalimi CDM partnerji letališča, ob poznavanju njihovih prednosti in omejitev ter dejanskih in predvidenih situacij. Sprejemanje odločitev CDM partnerjev letališča je odvisno od delitve natančnih in pravočasnih informacij in prilagojenih CDM postopkov letališča, mehanizmov in orodij.
Vsi programski elementi, povezani s stopnjo programskega zagotovila A-CDM sistema, so zunaj obsega delovanja pričujočega dokumenta.
Kot take, se bistvene zahteve Uredbe o medobratovalnosti ne štejejo za programske elemente v okviru pričujočega dokumenta. Pričujoči dokument ne podaja predpostavke o skladnosti, povezane z zahtevami vzdrževanja, varnosti, civilne/vojaške koordinacije ali okoljskih zadržkov. OPOMBA: Za te ER si prosim oglejte postopke ponudnikov storitve zračne navigacije. Zahteve v pričujočem dokumentu, ki se nanašajo »morebitne« izjave ali priporočila v normativnem referenčnem gradivu (Klavzula 2.1), naj se razlagajo kot popolnoma normativne (»naj«) za namen skladnosti s pričujočim dokumentom.

General Information

Status
Published
Public Enquiry End Date
30-Nov-2009
Publication Date
07-Jun-2010
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
03-Jun-2010
Due Date
08-Aug-2010
Completion Date
08-Jun-2010
Mandate

Buy Standard

Standard
EN 303 212 V1.1.1:2010
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 303 212 V1.1.1 (2010-06) - Airport Collaborative Decision Making (A-CDM); Community Specification for application under the Single European Sky Interoperability Regulation EC 552/2004
English language
57 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 212 V1.1.1 (2010-03) - Airport Collaborative Decision Making (A-CDM); Community Specification for application under the Single European Sky Interoperability Regulation EC 552/2004
English language
57 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 303 212 V1.1.1 (2009-08) - Airport Collaborative Decision Making (A-CDM); Community Specification for application under the Single European Sky Interoperability Regulation EC 552/2004
English language
58 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 303 212 V1.1.1:2010
01-julij-2010
6RGHORYDOQRRGORþDQMHQDOHWDOLãþLK $&'0 6SHFLILNDFLMD6NXSQRVWLY8UHGEL(&
RPHGREUDWRYDOQRVWLQDHQRWQHPHYURSVNHPQHEX
Airport Collaborative Decision Making (A-CDM) - Community Specification for application
under the Single European Sky Interoperability Regulation EC 552/2004
Ta slovenski standard je istoveten z: EN 303 212 Version 1.1.1
ICS:
03.220.50 =UDþQLWUDQVSRUW Air transport
SIST EN 303 212 V1.1.1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 303 212 V1.1.1:2010

---------------------- Page: 2 ----------------------

SIST EN 303 212 V1.1.1:2010

ETSI EN 303 212 V1.1.1 (2010-06)
European Standard (Telecommunications series)


Airport Collaborative Decision Making (A-CDM);
Community Specification for application under the
Single European Sky Interoperability Regulation EC 552/2004

---------------------- Page: 3 ----------------------

SIST EN 303 212 V1.1.1:2010
 2 ETSI EN 303 212 V1.1.1 (2010-06)



Reference
DEN/AERO-00002
Keywords
air traffic management, aeronautical,
interoperability
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 303 212 V1.1.1:2010
 3 ETSI EN 303 212 V1.1.1 (2010-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 9
4 Role, Responsibility and Interrelation requirements . 11
5 Functional, Technical, Interface and Validation Requirements . 12
5.1 Introduction . 12
5.1.1 Test and validation methods . 12
5.2 Airport CDM Elements . 12
5.3 Airport CDM Information Sharing - ACIS . 12
5.3.1 Background . 12
5.3.2 ACIS Functional Requirements . 13
5.3.2.1 ACIS Display of identical information . 13
5.3.2.2 ACIS User access . 13
5.3.2.3 Alert messaging and handling . 13
5.3.2.4 ACIS Manual data entry . 13
5.3.2.5 ACIS Flight information sharing . 13
5.3.2.6 ACIS Aeronautical and meteorological information sharing . 13
5.3.2.7 ACIS Archiving . 13
5.3.2.8 ACIS Filtering of information . 14
5.3.3 ACIS Technical Requirements . 14
5.3.3.1 ACIS Data validation . 14
5.3.3.2 ACIS Data protection . 14
5.3.3.3 ACIS Parameter and performance supervision . 14
5.3.3.4 ACIS Input data prioritization . 14
5.3.3.5 ACIS System time . 14
5.3.3.6 ACIS Data timeliness . 14
5.3.3.7 ACIS System availability . 15
5.3.3.8 ACIS System capacity. 15
5.3.4 ACIS Interface Requirements . 15
5.3.4.1 ACIS Flight identification . 15
5.3.4.2 ACIS Message formatting . 15
5.3.4.3 ACIS Data source identification . 15
5.3.4.4 ACIS Information exchange. 15
5.3.4.5 ACIS Event identification . 15
5.3.4.6 ACIS Duration parameters . 16
5.3.4.7 ACIS Airport resources identification . 16
5.3.4.8 ACIS Alert identification . 16
5.3.4.9 ACIS Key flight information. 16
5.4 Airport CDM Collaborative Turn-Round Process - CTRP . 16
5.4.1 Background . 16
5.4.2 CTRP Functional Requirements . 17
5.4.2.1 A-CDM CTRP Milestone approach . 17
5.4.2.2 A-CDM CTRP Milestone processing. 17
5.4.2.3 A-CDM CTRP Milestone updating . 17
5.4.2.4 A-CDM CTRP Operational alerting. 17
5.4.3 CTRP Technical Requirements . 18
ETSI

---------------------- Page: 5 ----------------------

SIST EN 303 212 V1.1.1:2010
 4 ETSI EN 303 212 V1.1.1 (2010-06)
5.4.3.1 Void. 18
5.4.4 CTRP Interface Requirements . 18
5.4.4.1 Void. 18
5.5 Airport CDM Variable Taxi Time Calculation - VTTC . 18
5.5.1 Background . 18
5.5.2 VTTC Functional Requirements . 18
5.5.2.1 A-CDM VTTC Variable taxi time calculation implementation . 18
5.5.2.2 A-CDM VTTC Automatic taxi time calculation and Update . 18
5.5.2.3 A-CDM VTTC Data timeliness . 18
5.5.2.4 A-CDM VTTC Input data . 18
5.5.2.5 A-CDM VTTC Methods . 19
5.5.3 VTTC Technical Requirements . 19
5.5.3.1 Void. 19
5.5.4 VTTC Interface Requirements . 19
5.5.4.1 Void. 19
5.6 Airport CDM Collaborative Management of Flight Updates - COFU . 19
5.6.1 Background . 19
5.6.2 COFU Functional Requirements . 19
5.6.2.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 19
5.6.2.2 A-CDM COFU Data timeliness . 19
5.6.2.3 A-CDM COFU Data Operations . 19
5.6.2.4 A-CDM COFU Message processing . 20
5.6.2.4.1 A-CDM COFU Message processing - Generic DPI process . 20
5.6.2.4.2 A-CDM COFU Message processing - Early DPI process . 20
5.6.2.4.3 A-CDM COFU Message processing - Target DPI process . 20
5.6.2.4.4 A-CDM COFU Message processing - ATC DPI process . 20
5.6.2.4.5 A-CDM COFU Message processing - Cancel DPI process . 20
5.6.2.4.6 A-CDM COFU Message processing - Sequence of DPI messages . 21
5.6.2.5 A-CDM COFU Message Content . 21
5.6.3 COFU Technical Requirements . 21
5.6.3.1 Void. 21
5.6.4 COFU Interface Requirements . 21
5.6.4.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 21
5.6.4.2 A-CDM COFU Data item identifier . 21
5.6.4.3 A-CDM COFU Data format . 21
5.6.4.4 A-CDM COFU Quality . 22
5.7 Airport CDM Collaborative Pre-Departure Sequence - CPDS. 22
5.7.1 Background . 22
5.7.2 CPDS Functional Requirements . 22
5.7.2.1 A-CDM CPDS Collaborative Pre-Departure Sequence Implementation . 22
5.7.2.2 A-CDM CPDS Distribution and Display . 22
5.7.2.3 A-CDM CPDS TSAT calculation . 22
5.7.3 CPDS Technical Requirements . 23
5.7.3.1 Void. 23
5.7.4 CPDS Interface Requirements . 23
5.7.4.1 Void. 23
5.8 Airport CDM in Adverse Conditions - CDAC . 23
5.8.1 Background . 23
5.8.2 CDM CDAC Functional Requirements . 23
5.8.2.1 A-CDM CDAC A-CDM in adverse conditions implementation . 23
5.8.2.2 A-CDM CDAC Flight cancellations and delay . 23
5.8.2.3 A-CDM CDAC Resource availability . 23
5.8.3 CDAC Technical Requirements . 23
5.8.3.1 Void. 23
5.8.4 CDAC Interface Requirements . 23
5.8.4.1 Void. 23
Annex SA (normative): Standards Annex . 24
SA.1 Correspondence between this European Standard and the Single European Sky Interoperability
Regulation (as amended) for A-CDM . 24
ETSI

---------------------- Page: 6 ----------------------

SIST EN 303 212 V1.1.1:2010
 5 ETSI EN 303 212 V1.1.1 (2010-06)
Annex A (normative): Checklist . 35
A.1 Interoperability Regulation Annex II Essential Requirements; Part A: General requirements . 36
A.2 Interoperability Regulation Annex II Essential Requirements Part B: Specific requirements . 43
A.2.1 Systems and procedures for airspace management. 43
A.2.2 Systems and procedures for air traffic flow management . 43
A.2.3 Systems and procedures for air traffic services . 44
A.2.3.1 Flight data processing systems. 44
A.2.3.2 Surveillance data processing systems . 50
A.2.3.3 Human-machine interface systems . 51
A.2.4 Communications systems and procedures for ground-to-ground, air-to-ground and air-to-air
communications . 52
A.2.5 Navigation systems and procedures . 53
A.2.6 Surveillance systems and procedures . 53
A.2.7 Systems and procedures for aeronautical information services . 53
A.2.8 Systems and procedures for the use of meteorological information . 54
Annex B (informative): The EN title in the official languages . 55
Annex C (informative): Bibliography . 56
History . 57

ETSI

---------------------- Page: 7 ----------------------

SIST EN 303 212 V1.1.1:2010
 6 ETSI EN 303 212 V1.1.1 (2010-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Aeronautics
(AERO).
The present document has been produced by ETSI in response to European Commission mandate M/390 for the
Interoperability of the European Air Traffic Management Network.
The present document has been developed in cooperation with Eurocae for compliance with the Essential Requirements
of the Single European Sky Interoperability Regulation [i.1] and/or requirements given in implementing rules for the
Single European Sky Interoperability Regulation.
The presumption of conformity which is linked to the full application of the present document can only be claimed after
the present document has been listed in the Official Journal of the European Union as Community Specification.
General and specific requirements for presumption of conformity to SES Interoperability Regulation 552/2004 as
amended by Regulation 1070/2009 are given in the normative annexes of the present document.
NOTE: Other requirements and other EU Regulations and/or Directives may be applicable to the product(s)
falling within the scope of the present document.

National transposition dates
Date of adoption of this EN: 17 May 2010
Date of latest announcement of this EN (doa): 31 August 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2011
Date of withdrawal of any conflicting National Standard (dow): 29 February 2012

Introduction
The European Union launched the Legislation "Single European Sky" (SES) in 2002 which was adopted in 2004 and
amended by Regulation (EC) No 1070/2009 [i.1].
The SES legislation is based on a framework of 4 regulations, which includes the Interoperability Regulation [i.1]. The
objective of the Interoperability Regulation is to ensure interoperability of the European Air Traffic Management
Network (EATMN) consistent with air navigation services. Under this regulation, the use of a European Standard
referenced in the Official Journal of the European Union as Community Specification (CS) is a means of compliance to
the essential requirements of the Regulation and/or the relevant implementing rules for interoperability.
ETSI

---------------------- Page: 8 ----------------------

SIST EN 303 212 V1.1.1:2010
 7 ETSI EN 303 212 V1.1.1 (2010-06)
The present document takes into account the Council Decision 2009/320/EC [i.4] endorsing the European Air Traffic
Management Master Plan of the Single European Sky ATM Research (SESAR) project [i.4].
Figure 1 shows the high level relationship between the Eurocontrol and Eurocae which were developed in parallel.
EUROCONTROL EUROCAE
Documents Documents
System Requirements
Concept of Operations
Document (ED-141)
Functional
Interface Definition
Requirements
Document (ED-145)
Document
Implementation
Test and Validation
Manual
Document (ED-146)

Figure 1: Eurocontrol and Eurocae Document Relationship
ETSI

---------------------- Page: 9 ----------------------

SIST EN 303 212 V1.1.1:2010
 8 ETSI EN 303 212 V1.1.1 (2010-06)
1 Scope
The present document is applicable to Air Traffic Management Airport Collaborative Decision Making (A-CDM).
The present document addresses the specific roles, responsibilities, procedures, systems and interfaces needed to fulfil
the Airport CDM (A-CDM) Operating Concept as requested by Mandate M/390 of the European Commission. It
references existing documentation where necessary to clarify the more detailed aspects of a procedure or system
implementation requirement to avoid unnecessary repetition.
Airport Collaborative Decision making (A-CDM) is about improving the way operational partners at airports and
European ATFCM (Air Traffic Flow and Capacity Management, Air Traffic Control, Airlines, Ground Handling
Agents/Units and Airports) work together at an operational level.
A-CDM allows an Airport CDM partner to make the right decisions for a flight during the whole Airport CDM process
in collaboration with other Airport CDM partners, knowing their preferences and constraints and the actual and
predicted situation. The decision making by the Airport CDM partners is dependent upon the sharing of accurate and
timely information and upon adapted Airport CDM procedures, mechanisms and tools.
Any software elements related to the software assurance level of an A-CDM System are outside of the scope of the
present document. As such the essential requirements of the Interoperability Regulation are not considered for software
elements within the present document.
The present document does not give a presumption of conformity related to maintenance requirements, safety,
civil/military coordination or environmental constraints.
NOTE: For these ERs, please refer to the Air Navigation Service Provider procedures.
Requirements in the present document which refer to "should" statements or recommendations in the normatively
referenced material (clause 2.1) are to be interpreted as fully normative ("shall") for the purpose of compliance with the
present document.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Eurocontrol: "Airport CDM Operational Concept Document" (Version 3.0, Sept 2006).
NOTE: See figure 1.
[2] Eurocontrol: "Airport CDM Fun
...

ETSI EN 303 212 V1.1.1 (2010-06)
European Standard (Telecommunications series)


Airport Collaborative Decision Making (A-CDM);
Community Specification for application under the
Single European Sky Interoperability Regulation EC 552/2004

---------------------- Page: 1 ----------------------
2 ETSI EN 303 212 V1.1.1 (2010-06)



Reference
DEN/AERO-00002
Keywords
air traffic management, aeronautical,
interoperability
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 212 V1.1.1 (2010-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 9
4 Role, Responsibility and Interrelation requirements . 11
5 Functional, Technical, Interface and Validation Requirements . 12
5.1 Introduction . 12
5.1.1 Test and validation methods . 12
5.2 Airport CDM Elements . 12
5.3 Airport CDM Information Sharing - ACIS . 12
5.3.1 Background . 12
5.3.2 ACIS Functional Requirements . 13
5.3.2.1 ACIS Display of identical information . 13
5.3.2.2 ACIS User access . 13
5.3.2.3 Alert messaging and handling . 13
5.3.2.4 ACIS Manual data entry . 13
5.3.2.5 ACIS Flight information sharing . 13
5.3.2.6 ACIS Aeronautical and meteorological information sharing . 13
5.3.2.7 ACIS Archiving . 13
5.3.2.8 ACIS Filtering of information . 14
5.3.3 ACIS Technical Requirements . 14
5.3.3.1 ACIS Data validation . 14
5.3.3.2 ACIS Data protection . 14
5.3.3.3 ACIS Parameter and performance supervision . 14
5.3.3.4 ACIS Input data prioritization . 14
5.3.3.5 ACIS System time . 14
5.3.3.6 ACIS Data timeliness . 14
5.3.3.7 ACIS System availability . 15
5.3.3.8 ACIS System capacity. 15
5.3.4 ACIS Interface Requirements . 15
5.3.4.1 ACIS Flight identification . 15
5.3.4.2 ACIS Message formatting . 15
5.3.4.3 ACIS Data source identification . 15
5.3.4.4 ACIS Information exchange. 15
5.3.4.5 ACIS Event identification . 15
5.3.4.6 ACIS Duration parameters . 16
5.3.4.7 ACIS Airport resources identification . 16
5.3.4.8 ACIS Alert identification . 16
5.3.4.9 ACIS Key flight information. 16
5.4 Airport CDM Collaborative Turn-Round Process - CTRP . 16
5.4.1 Background . 16
5.4.2 CTRP Functional Requirements . 17
5.4.2.1 A-CDM CTRP Milestone approach . 17
5.4.2.2 A-CDM CTRP Milestone processing. 17
5.4.2.3 A-CDM CTRP Milestone updating . 17
5.4.2.4 A-CDM CTRP Operational alerting. 17
5.4.3 CTRP Technical Requirements . 18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 212 V1.1.1 (2010-06)
5.4.3.1 Void. 18
5.4.4 CTRP Interface Requirements . 18
5.4.4.1 Void. 18
5.5 Airport CDM Variable Taxi Time Calculation - VTTC . 18
5.5.1 Background . 18
5.5.2 VTTC Functional Requirements . 18
5.5.2.1 A-CDM VTTC Variable taxi time calculation implementation . 18
5.5.2.2 A-CDM VTTC Automatic taxi time calculation and Update . 18
5.5.2.3 A-CDM VTTC Data timeliness . 18
5.5.2.4 A-CDM VTTC Input data . 18
5.5.2.5 A-CDM VTTC Methods . 19
5.5.3 VTTC Technical Requirements . 19
5.5.3.1 Void. 19
5.5.4 VTTC Interface Requirements . 19
5.5.4.1 Void. 19
5.6 Airport CDM Collaborative Management of Flight Updates - COFU . 19
5.6.1 Background . 19
5.6.2 COFU Functional Requirements . 19
5.6.2.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 19
5.6.2.2 A-CDM COFU Data timeliness . 19
5.6.2.3 A-CDM COFU Data Operations . 19
5.6.2.4 A-CDM COFU Message processing . 20
5.6.2.4.1 A-CDM COFU Message processing - Generic DPI process . 20
5.6.2.4.2 A-CDM COFU Message processing - Early DPI process . 20
5.6.2.4.3 A-CDM COFU Message processing - Target DPI process . 20
5.6.2.4.4 A-CDM COFU Message processing - ATC DPI process . 20
5.6.2.4.5 A-CDM COFU Message processing - Cancel DPI process . 20
5.6.2.4.6 A-CDM COFU Message processing - Sequence of DPI messages . 21
5.6.2.5 A-CDM COFU Message Content . 21
5.6.3 COFU Technical Requirements . 21
5.6.3.1 Void. 21
5.6.4 COFU Interface Requirements . 21
5.6.4.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 21
5.6.4.2 A-CDM COFU Data item identifier . 21
5.6.4.3 A-CDM COFU Data format . 21
5.6.4.4 A-CDM COFU Quality . 22
5.7 Airport CDM Collaborative Pre-Departure Sequence - CPDS. 22
5.7.1 Background . 22
5.7.2 CPDS Functional Requirements . 22
5.7.2.1 A-CDM CPDS Collaborative Pre-Departure Sequence Implementation . 22
5.7.2.2 A-CDM CPDS Distribution and Display . 22
5.7.2.3 A-CDM CPDS TSAT calculation . 22
5.7.3 CPDS Technical Requirements . 23
5.7.3.1 Void. 23
5.7.4 CPDS Interface Requirements . 23
5.7.4.1 Void. 23
5.8 Airport CDM in Adverse Conditions - CDAC . 23
5.8.1 Background . 23
5.8.2 CDM CDAC Functional Requirements . 23
5.8.2.1 A-CDM CDAC A-CDM in adverse conditions implementation . 23
5.8.2.2 A-CDM CDAC Flight cancellations and delay . 23
5.8.2.3 A-CDM CDAC Resource availability . 23
5.8.3 CDAC Technical Requirements . 23
5.8.3.1 Void. 23
5.8.4 CDAC Interface Requirements . 23
5.8.4.1 Void. 23
Annex SA (normative): Standards Annex . 24
SA.1 Correspondence between this European Standard and the Single European Sky Interoperability
Regulation (as amended) for A-CDM . 24
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 212 V1.1.1 (2010-06)
Annex A (normative): Checklist . 35
A.1 Interoperability Regulation Annex II Essential Requirements; Part A: General requirements . 36
A.2 Interoperability Regulation Annex II Essential Requirements Part B: Specific requirements . 43
A.2.1 Systems and procedures for airspace management. 43
A.2.2 Systems and procedures for air traffic flow management . 43
A.2.3 Systems and procedures for air traffic services . 44
A.2.3.1 Flight data processing systems. 44
A.2.3.2 Surveillance data processing systems . 50
A.2.3.3 Human-machine interface systems . 51
A.2.4 Communications systems and procedures for ground-to-ground, air-to-ground and air-to-air
communications . 52
A.2.5 Navigation systems and procedures . 53
A.2.6 Surveillance systems and procedures . 53
A.2.7 Systems and procedures for aeronautical information services . 53
A.2.8 Systems and procedures for the use of meteorological information . 54
Annex B (informative): The EN title in the official languages . 55
Annex C (informative): Bibliography . 56
History . 57

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 303 212 V1.1.1 (2010-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Aeronautics
(AERO).
The present document has been produced by ETSI in response to European Commission mandate M/390 for the
Interoperability of the European Air Traffic Management Network.
The present document has been developed in cooperation with Eurocae for compliance with the Essential Requirements
of the Single European Sky Interoperability Regulation [i.1] and/or requirements given in implementing rules for the
Single European Sky Interoperability Regulation.
The presumption of conformity which is linked to the full application of the present document can only be claimed after
the present document has been listed in the Official Journal of the European Union as Community Specification.
General and specific requirements for presumption of conformity to SES Interoperability Regulation 552/2004 as
amended by Regulation 1070/2009 are given in the normative annexes of the present document.
NOTE: Other requirements and other EU Regulations and/or Directives may be applicable to the product(s)
falling within the scope of the present document.

National transposition dates
Date of adoption of this EN: 17 May 2010
Date of latest announcement of this EN (doa): 31 August 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2011
Date of withdrawal of any conflicting National Standard (dow): 29 February 2012

Introduction
The European Union launched the Legislation "Single European Sky" (SES) in 2002 which was adopted in 2004 and
amended by Regulation (EC) No 1070/2009 [i.1].
The SES legislation is based on a framework of 4 regulations, which includes the Interoperability Regulation [i.1]. The
objective of the Interoperability Regulation is to ensure interoperability of the European Air Traffic Management
Network (EATMN) consistent with air navigation services. Under this regulation, the use of a European Standard
referenced in the Official Journal of the European Union as Community Specification (CS) is a means of compliance to
the essential requirements of the Regulation and/or the relevant implementing rules for interoperability.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 303 212 V1.1.1 (2010-06)
The present document takes into account the Council Decision 2009/320/EC [i.4] endorsing the European Air Traffic
Management Master Plan of the Single European Sky ATM Research (SESAR) project [i.4].
Figure 1 shows the high level relationship between the Eurocontrol and Eurocae which were developed in parallel.
EUROCONTROL EUROCAE
Documents Documents
System Requirements
Concept of Operations
Document (ED-141)
Functional
Interface Definition
Requirements
Document (ED-145)
Document
Implementation
Test and Validation
Manual
Document (ED-146)

Figure 1: Eurocontrol and Eurocae Document Relationship
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 303 212 V1.1.1 (2010-06)
1 Scope
The present document is applicable to Air Traffic Management Airport Collaborative Decision Making (A-CDM).
The present document addresses the specific roles, responsibilities, procedures, systems and interfaces needed to fulfil
the Airport CDM (A-CDM) Operating Concept as requested by Mandate M/390 of the European Commission. It
references existing documentation where necessary to clarify the more detailed aspects of a procedure or system
implementation requirement to avoid unnecessary repetition.
Airport Collaborative Decision making (A-CDM) is about improving the way operational partners at airports and
European ATFCM (Air Traffic Flow and Capacity Management, Air Traffic Control, Airlines, Ground Handling
Agents/Units and Airports) work together at an operational level.
A-CDM allows an Airport CDM partner to make the right decisions for a flight during the whole Airport CDM process
in collaboration with other Airport CDM partners, knowing their preferences and constraints and the actual and
predicted situation. The decision making by the Airport CDM partners is dependent upon the sharing of accurate and
timely information and upon adapted Airport CDM procedures, mechanisms and tools.
Any software elements related to the software assurance level of an A-CDM System are outside of the scope of the
present document. As such the essential requirements of the Interoperability Regulation are not considered for software
elements within the present document.
The present document does not give a presumption of conformity related to maintenance requirements, safety,
civil/military coordination or environmental constraints.
NOTE: For these ERs, please refer to the Air Navigation Service Provider procedures.
Requirements in the present document which refer to "should" statements or recommendations in the normatively
referenced material (clause 2.1) are to be interpreted as fully normative ("shall") for the purpose of compliance with the
present document.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Eurocontrol: "Airport CDM Operational Concept Document" (Version 3.0, Sept 2006).
NOTE: See figure 1.
[2] Eurocontrol: "Airport CDM Functional Requirements Document" (Version 4.0 May 2009).
NOTE: See figure 1.
[3] Eurocontrol: "CFMU DPI Implementation Guide" (Version 1.3).
NOTE: See figure 1.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 303 212 V1.1.1 (2010-06)
[4] Eurocontrol: "CFMU Flight Progress Messages" (Version 1.6).
NOTE: See figure 1.
[5] Eurocae: "Minimum Technical Specification for the Airport Collaborative Decision Making
(Airport-CDM)" - ED141 - (Version 1, October 2008).
NOTE: See figure 1.
[6] Eurocae: "Airport-CDM Interface Specification" - ED145 - (Version 1, October 2008).
NOTE: See figure 1.
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Regulation (EC) No 552/2004 of the European Parliament and of the Council of 10 March 2004 on
the interoperability of the European Air Traffic Management network (the Interoperabili
...

Final draft ETSI EN 303 212 V1.1.1 (2010-03)
European Standard (Telecommunications series)


Airport Collaborative Decision Making (A-CDM);
Community Specification for application under the
Single European Sky Interoperability Regulation EC 552/2004

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 212 V1.1.1 (2010-03)



Reference
DEN/AERO-00002
Keywords
air traffic management, aeronautical, interoperability
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In
case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for
the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 10
4 Role, Responsibility and Interrelation requirements . 11
5 Functional, Technical, Interface and Validation Requirements . 12
5.1 Introduction . 12
5.1.1 Test and validation methods . 12
5.2 Airport CDM Elements . 12
5.3 Airport CDM Information Sharing - ACIS . 12
5.3.1 Background . 12
5.3.2 ACIS Functional Requirements . 13
5.3.2.1 ACIS Display of identical information . 13
5.3.2.2 ACIS User access . 13
5.3.2.3 Alert messaging and handling . 13
5.3.2.4 ACIS Manual data entry . 13
5.3.2.5 ACIS Flight information sharing . 13
5.3.2.6 ACIS Aeronautical and meteorological information sharing . 13
5.3.2.7 ACIS Archiving . 13
5.3.2.8 ACIS Filtering of information . 14
5.3.3 ACIS Technical Requirements . 14
5.3.3.1 ACIS Data validation . 14
5.3.3.2 ACIS Data protection . 14
5.3.3.3 ACIS Parameter and performance supervision . 14
5.3.3.4 ACIS Input data prioritization . 14
5.3.3.5 ACIS System time . 14
5.3.3.6 ACIS Data timeliness . 14
5.3.3.7 ACIS System availability . 15
5.3.3.8 ACIS System capacity. 15
5.3.4 ACIS Interface Requirements . 15
5.3.4.1 ACIS Flight identification . 15
5.3.4.2 ACIS Message formatting . 15
5.3.4.3 ACIS Data source identification . 15
5.3.4.4 ACIS Information exchange. 15
5.3.4.5 ACIS Event identification . 15
5.3.4.6 ACIS Duration parameters . 16
5.3.4.7 ACIS Airport resources identification . 16
5.3.4.8 ACIS Alert identification . 16
5.3.4.9 ACIS Key flight information. 16
5.4 Airport CDM Collaborative Turn-Round Process - CTRP . 16
5.4.1 Background . 16
5.4.2 CTRP Functional Requirements . 17
5.4.2.1 A-CDM CTRP Milestone approach . 17
5.4.2.2 A-CDM CTRP Milestone processing. 17
5.4.2.3 A-CDM CTRP Milestone updating . 17
5.4.2.4 A-CDM CTRP Operational alerting. 17
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
5.4.3 CTRP Technical Requirements . 18
5.4.3.1 Void. 18
5.4.4 CTRP Interface Requirements . 18
5.4.4.1 Void. 18
5.5 Airport CDM Variable Taxi Time Calculation - VTTC . 18
5.5.1 Background . 18
5.5.2 VTTC Functional Requirements . 18
5.5.2.1 A-CDM VTTC Variable taxi time calculation implementation . 18
5.5.2.2 A-CDM VTTC Automatic taxi time calculation and Update . 18
5.5.2.3 A-CDM VTTC Data timeliness . 18
5.5.2.4 A-CDM VTTC Input data . 18
5.5.2.5 A-CDM VTTC Methods . 19
5.5.3 VTTC Technical Requirements . 19
5.5.3.1 Void. 19
5.5.4 VTTC Interface Requirements . 19
5.5.4.1 Void. 19
5.6 Airport CDM Collaborative Management of Flight Updates - COFU . 19
5.6.1 Background . 19
5.6.2 COFU Functional Requirements . 19
5.6.2.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 19
5.6.2.2 A-CDM COFU Data timeliness . 19
5.6.2.3 A-CDM COFU Data Operations . 19
5.6.2.4 A-CDM COFU Message processing . 20
5.6.2.4.1 A-CDM COFU Message processing - Generic DPI process . 20
5.6.2.4.2 A-CDM COFU Message processing - Early DPI process . 20
5.6.2.4.3 A-CDM COFU Message processing - Target DPI process . 20
5.6.2.4.4 A-CDM COFU Message processing - ATC DPI process . 20
5.6.2.4.5 A-CDM COFU Message processing - Cancel DPI process . 20
5.6.2.4.6 A-CDM COFU Message processing - Sequence of DPI messages . 21
5.6.2.5 A-CDM COFU Message Content . 21
5.6.3 COFU Technical Requirements . 21
5.6.3.1 Void. 21
5.6.4 COFU Interface Requirements . 21
5.6.4.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 21
5.6.4.2 A-CDM COFU Data item identifier . 21
5.6.4.3 A-CDM COFU Data format . 21
5.6.4.4 A-CDM COFU Quality . 22
5.7 Airport CDM Collaborative Pre-Departure Sequence - CPDS. 22
5.7.1 Background . 22
5.7.2 CPDS Functional Requirements . 22
5.7.2.1 A-CDM CPDS Collaborative Pre-Departure Sequence Implementation . 22
5.7.2.2 A-CDM CPDS Distribution and Display . 22
5.7.2.3 A-CDM CPDS TSAT calculation . 22
5.7.3 CPDS Technical Requirements . 23
5.7.3.1 Void. 23
5.7.4 CPDS Interface Requirements . 23
5.7.4.1 Void. 23
5.8 Airport CDM in Adverse Conditions - CDAC . 23
5.8.1 Background . 23
5.8.2 CDM CDAC Functional Requirements . 23
5.8.2.1 A-CDM CDAC A-CDM in adverse conditions implementation . 23
5.8.2.2 A-CDM CDAC Flight cancellations and delay . 23
5.8.2.3 A-CDM CDAC Resource availability . 23
5.8.3 CDAC Technical Requirements . 23
5.8.3.1 Void. 23
5.8.4 CDAC Interface Requirements . 23
5.8.4.1 Void. 23
Annex SA (normative): Standards Annex . 24
SA.1 Correspondence between this European Standard and the Single European Sky Interoperability
Regulation (as amended) for A-CDM . 24
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
Annex A (normative): Checklist . 35
A.1 Interoperability Regulation Annex II Essential Requirements; Part A: General requirements . 36
A.2 Interoperability Regulation Annex II Essential Requirements Part B: Specific requirements . 43
A.2.1 Systems and procedures for airspace management. 43
A.2.2 Systems and procedures for air traffic flow management . 43
A.2.3 Systems and procedures for air traffic services . 44
A.2.3.1 Flight data processing systems. 44
A.2.3.2 Surveillance data processing systems . 50
A.2.3.3 Human-machine interface systems . 51
A.2.4 Communications systems and procedures for ground-to-ground, air-to-ground and air-to-air
communications . 52
A.2.5 Navigation systems and procedures . 53
A.2.6 Surveillance systems and procedures . 53
A.2.7 Systems and procedures for aeronautical information services . 53
A.2.8 Systems and procedures for the use of meteorological information . 54
Annex B (informative): The EN title in the official languages . 55
Annex C (informative): Bibliography . 56
History . 57

ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining
to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in
ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect
of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server
(http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can
be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server)
which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Aeronautics
(AERO), and is now submitted for the Vote phase of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to European Commission mandate M/390 for the
Interoperability of the European Air Traffic Management Network.
The present document has been developed in cooperation with Eurocae for compliance with the Essential Requirements of
the Single European Sky Interoperability Regulation [i.1] and/or requirements given in implementing rules for the Single
European Sky Interoperability Regulation.
The presumption of conformity which is linked to the full application of the present document can only be claimed after the
present document has been listed in the Official Journal of the European Union as Community Specification.
General and specific requirements for presumption of conformity to SES Interoperability Regulation 552/2004 as
amended by Regulation 1070/2009 are given in the normative annexes of the present document.
NOTE: Other requirements and other EU Regulations and/or Directives may be applicable to the product(s) falling
within the scope of the present document.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The European Union launched the Legislation "Single European Sky" (SES) in 2002 which was adopted in 2004 and
amended by Regulation (EC) No 1070/2009 [i.1].
The SES legislation is based on a framework of 4 regulations, which includes the Interoperability Regulation [i.1]. The
objective of the Interoperability Regulation is to ensure interoperability of the European Air Traffic Management Network
(EATMN) consistent with air navigation services. Under this regulation, the use of a European Standard referenced in the
Official Journal of the European Union as Community Specification (CS) is a means of compliance to the essential
requirements of the Regulation and/or the relevant implementing rules for interoperability.
The present document takes into account the Council Decision 2009/320/EC [i.4] endorsing the European Air Traffic
Management Master Plan of the Single European Sky ATM Research (SESAR) project [i.4].
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
Figure 1 shows the high level relationship between the Eurocontrol and Eurocae which were developed in parallel.
EUROCONTROL EUROCAE
Documents Documents
System Requirements
Concept of Operations
Document (ED-141)
Functional
Interface Definition
Requirements
Document (ED-145)
Document
Implementation Test and Validation
Manual Document (ED-146)

Figure 1: Eurocontrol and Eurocae Document Relationship
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
1 Scope
The present document is applicable to Air Traffic Management Airport Collaborative Decision Making (A-CDM).
The present document addresses the specific roles, responsibilities, procedures, systems and interfaces needed to fulfil the
Airport CDM (A-CDM) Operating Concept as requested by Mandate M/390 of the European Commission. It references
existing documentation where necessary to clarify the more detailed aspects of a procedure or system implementation
requirement to avoid unnecessary repetition.
Airport Collaborative Decision making (A-CDM) is about improving the way operational partners at airports and European
ATFCM (Air Traffic Flow and Capacity Management, Air Traffic Control, Airlines, Ground Handling Agents/Units and
Airports) work together at an operational level.
A-CDM allows an Airport CDM partner to make the right decisions for a flight during the whole Airport CDM process in
collaboration with other Airport CDM partners, knowing their preferences and constraints and the actual and predicted
situation. The decision making by the Airport CDM partners is dependent upon the sharing of accurate and timely
information and upon adapted Airport CDM procedures, mechanisms and tools.
Any software elements related to the software assurance level of an A-CDM System are outside of the scope of the present
document. As such the essential requirements of the Interoperability Regulation are not considered for software elements
within the present document.
The present document does not give a presumption of conformity related to maintenance requirements, safety, civil/military
coordination or environmental constraints.
NOTE: For these ERs, please refer to the Air Navigation Service Provider procedures.
Requirements in the present document which refer to "should" statements or recommendations in the normatively
referenced material (clause 2.1) are to be interpreted as fully normative ("shall") for the purpose of compliance with the
present document.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the purposes
of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated references,
only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any
amendments) applies.
[1] Eurocontrol: "Airport CDM Operational Concept Document" (Version 3.0, Sept 2006).
NOTE: See figure 1.
ETSI

---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 303 212 V1.1.1 (2010-03)
[2] Eurocontrol: "Airport CDM Functional Requirements Document" (Version 4.0 May 2009).
NOTE: See figure 1.
[3] Eurocontrol: "CFMU DPI Implementation Guide" (Version 1.3).
NOTE: See figure 1.
[4] Eurocontrol: "CFMU Flight Progress Messages" (Version 1.6).
NOTE: See figure 1.
[5] Eurocae: "Minimum Technical Specification for the Airport Collaborative Decision Making (Airport-
CDM)" - ED141 - (Ver
...

Draft ETSI EN 303 212 V1.1.1 (2009-08)
European Standard (Telecommunications series)


Airport Collaborative Decision Making (A-CDM);
Community Specification for application under the
Single European Sky Interoperability Regulation EC 552/2004

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 212 V1.1.1 (2009-08)



Reference
DEN/AERO-00002
Keywords
Air Traffic Management, aeronautical,
interoperability
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 212 V1.1.1 (2009-08)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 9
4 Role, Responsibility and Interrelation requirements . 11
5 Functional, Technical, Interface and Validation Requirements . 12
5.1 Introduction . 12
5.1.1 Test and validation methods . 12
5.2 Airport CDM Elements . 12
5.3 Airport CDM Information Sharing - ACIS . 12
5.3.1 Background . 12
5.3.2 ACIS Functional Requirements . 13
5.3.2.1 A-CDM ACIS Display of identical information . 13
5.3.2.2 A-CDM ACIS User access . 13
5.3.2.3 A-CDM ACIS Alert messaging and handling . 13
5.3.2.4 A-CDM ACIS Manual data entry . 13
5.3.2.5 A-CDM ACIS Flight information sharing . 13
5.3.2.6 A-CDM ACIS Aeronautical and meteorological information sharing . 13
5.3.2.7 A-CDM ACIS Archiving . 13
5.3.2.8 A-CDM ACIS Filtering of information. 14
5.3.3 ACIS Technical Requirements . 14
5.3.3.1 A-CDM ACIS Data validation . 14
5.3.3.2 A-CDM ACIS Data protection . 14
5.3.3.3 A-CDM ACIS Parameter and performance supervision . 14
5.3.3.4 A-CDM ACIS Input data prioritization. 14
5.3.3.5 A-CDM ACIS System time . 14
5.3.3.6 A-CDM ACIS Data timeliness . 14
5.3.3.7 A-CDM ACIS System availability . 15
5.3.3.8 A-CDM ACIS System capacity . 15
5.3.4 ACIS Interface Requirements . 15
5.3.4.1 A-CDM ACIS Flight identification . 15
5.3.4.2 A-CDM ACIS Message formatting . 15
5.3.4.3 A-CDM ACIS Data source identification . 15
5.3.4.4 A-CDM ACIS Information exchange . 15
5.3.4.5 A-CDM ACIS Event identification . 15
5.3.4.6 A-CDM ACIS Duration parameters . 16
5.3.4.7 A-CDM ACIS Airport resources identification . 16
5.3.4.8 A-CDM ACIS Alert identification . 16
5.3.4.9 A-CDM ACIS Key flight information . 16
5.4 Airport CDM Collaborative Turn-Round Process - CTRP . 16
5.4.1 Background . 16
5.4.2 CTRP Functional Requirements . 17
5.4.2.1 A-CDM CTRP Milestone approach . 17
5.4.2.2 A-CDM CTRP Milestone processing. 17
5.4.2.3 A-CDM CTRP Milestone updating . 17
5.4.2.4 A-CDM CTRP Operational alerting. 17
5.4.3 CTRP Technical Requirements . 18
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 212 V1.1.1 (2009-08)
5.4.3.1 Void. 18
5.4.4 CTRP Interface Requirements . 18
5.4.4.1 Void. 18
5.5 Airport CDM Variable Taxi Time Calculation - VTTC . 18
5.5.1 Background . 18
5.5.2 VTTC Functional Requirements . 18
5.5.2.1 A-CDM VTTC Variable taxi time calculation implementation . 18
5.5.2.2 A-CDM VTTC Automatic taxi time calculation and Update . 18
5.5.2.3 A-CDM VTTC Data timeliness . 18
5.5.2.4 A-CDM VTTC Input data . 18
5.5.2.5 A-CDM VTTC Methods . 19
5.5.3 VTTC Technical Requirements . 19
5.5.3.1 Void. 19
5.5.4 VTTC Interface Requirements . 19
5.5.4.1 Void. 19
5.6 Airport CDM Collaborative Management of Flight Updates - COFU . 19
5.6.1 Background . 19
5.6.2 COFU Functional Requirements . 19
5.6.2.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 19
5.6.2.2 A-CDM COFU Data timeliness . 19
5.6.2.3 A-CDM COFU Data Operations . 19
5.6.2.4 A-CDM COFU Message processing . 20
5.6.2.4.1 A-CDM COFU Message processing - Generic DPI process . 20
5.6.2.4.2 A-CDM COFU Message processing - Early DPI process . 20
5.6.2.4.3 A-CDM COFU Message processing - Target DPI process . 20
5.6.2.4.4 A-CDM COFU Message processing - ATC DPI process . 20
5.6.2.4.5 A-CDM COFU Message processing - Cancel DPI process . 20
5.6.2.4.6 A-CDM COFU Message processing - Sequence of DPI messages . 21
5.6.2.5 A-CDM COFU Message Content . 21
5.6.3 COFU Technical Requirements . 21
5.6.3.1 Void. 21
5.6.4 COFU Interface Requirements . 21
5.6.4.1 A-CDM COFU Collaborative Management of Flight Updates Implementation . 21
5.6.4.2 A-CDM COFU Data item identifier . 21
5.6.4.3 A-CDM COFU Data format . 21
5.6.4.4 A-CDM COFU Quality . 22
5.7 Airport CDM Collaborative Pre-Departure Sequence - CPDS. 22
5.7.1 Background . 22
5.7.2 CPDS Functional Requirements . 22
5.7.2.1 A-CDM CPDS Collaborative Pre-Departure Sequence Implementation . 22
5.7.2.2 A-CDM CPDS Distribution and Display . 22
5.7.2.3 A-CDM CPDS TSAT calculation . 22
5.7.3 CPDS Technical Requirements . 23
5.7.3.1 Void. 23
5.7.4 CPDS Interface Requirements . 23
5.7.4.1 Void. 23
5.8 Airport CDM in Adverse Conditions - CDAC . 23
5.8.1 Background . 23
5.8.2 CDM CDAC Functional Requirements . 23
5.8.2.1 A-CDM CDAC A-CDM in adverse conditions implementation . 23
5.8.2.2 A-CDM CDAC Flight cancellations and delay . 23
5.8.2.3 A-CDM CDAC Resource availability . 23
5.8.3 CDAC Technical Requirements . 23
5.8.3.1 Void. 23
5.8.4 CDAC Interface Requirements . 23
5.8.4.1 Void. 23
Annex SA (normative): Standards Annex . 24
SA.1 Correspondence between this European Standard and the Single European Sky Interoperability
Regulation for A-CDM . 24
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 212 V1.1.1 (2009-08)
Annex A (normative): Checklist . 35
A.1 Interoperability Regulation Annex II Essential Requirements; Part A: General requirements . 36
A.2 Interoperability Regulation Annex II Essential Requirements Part B: Specific requirements . 43
A.2.1 Systems and procedures for airspace management. 43
A.2.2 Systems and procedures for air traffic flow management . 43
A.2.3 Systems and procedures for air traffic services . 44
A.2.3.1 Flight data processing systems. 44
A.2.3.2 Surveillance data processing systems . 51
A.2.3.3 Human-machine interface systems . 52
A.2.4 Communications systems and procedures for ground-to-ground, air-to-ground and air-to-air
communications . 53
A.2.5 Navigation systems and procedures . 54
A.2.6 Surveillance systems and procedures . 54
A.2.7 Systems and procedures for aeronautical information services . 54
A.2.8 Systems and procedures for the use of meteorological information . 55
Annex B (informative): The EN title in the official languages . 56
Annex C (informative): Bibliography . 57
History . 58

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 212 V1.1.1 (2009-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Aeronautics
(AERO), and is now submitted for the Public Enquiry phase of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to European Commission mandate M/390 for the
Interoperability of the European Air Traffic Management Network.
The present document has been developed in cooperation with Eurocae for compliance with the Essential Requirements
of the Single European Sky Interoperability Regulation [i.1] and/or requirements given in implementing rules for the
Single European Sky Interoperability Regulation.
The presumption of conformity which is linked to the full application of the present document can only be claimed after
the present document has been listed in the Official Journal of the European Union as Community Specification.
General and specific requirements for presumption of conformity to SES Interoperability Regulation 552/2004 are
given in the normative annexes of the present document.
NOTE: Other requirements and other EU Regulations and/or Directives may be applicable to the product(s)
falling within the scope of the present document.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

Introduction
The European Union launched the Legislation "Single European Sky" (SES) in 2002 which was adopted in 2004.
The SES legislation is based on a framework of 4 regulations, which includes the Interoperability Regulation [i.2]. The
objective of the Interoperability Regulation is to ensure interoperability of the European Air Traffic Management
Network (EATMN) consistent with air navigation services. Under this regulation, the use of a European Standard
referenced in the Official Journal of the European Union as Community Specification (CS) is a means of compliance to
the essential requirements of the Regulation and/or the relevant implementing rules for interoperability.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 212 V1.1.1 (2009-08)
Figure 1 shows the high level relationship between the Eurocontrol and Eurocae which were developed in parallel.
EUROCONTROL EUROCAE
Documents Documents
System Requirements
Concept of Operations
Document (ED-141)
Functional
Interface Definition
Requirements
Document (ED-145)
Document
Implementation
Test and Validation
Manual
Document (ED-146)

Figure 1: Eurocontrol and Eurocae Document Relationship
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 212 V1.1.1 (2009-08)
1 Scope
The present document is applicable to Air Traffic Management Airport Collaborative Decision Making (A-CDM).
The present document addresses the specific roles, responsibilities, procedures, systems and interfaces needed to fulfil
the Airport CDM (A-CDM) Operating Concept as requested by Mandate M/390 of the European Commission. It
references existing documentation where necessary to clarify the more detailed aspects of a procedure or system
implementation requirement to avoid unnecessary repetition.
Airport Collaborative Decision making (A-CDM) is about improving the way operational partners at airports and
European ATFCM (Air Traffic Flow and Capacity Management, Air Traffic Control, Airlines, Ground Handling
Agents/Units and Airports) work together at an operational level.
A-CDM allows an Airport CDM partner to make the right decisions for a flight during the whole Airport CDM process
in collaboration with other Airport CDM partners, knowing their preferences and constraints and the actual and
predicted situation. The decision making by the Airport CDM partners is dependent upon the sharing of accurate and
timely information and upon adapted Airport CDM procedures, mechanisms and tools.
Any software elements related to the software assurance level of an A-CDM System are outside of the scope of the
present document. As such the essential requirements of the Interoperability Regulation are not considered for software
elements within the present document.
The present document does not give a presumption of conformity related to maintenance requirements, safety,
civil/military coordination or environmental constraints.
NOTE: For these ERs, please refer to the Air Navigation Service Provider procedures.
Requirements in this EN which refer to "should" statements or recommendations in the normatively referenced material
(clause 2.1) are to be interpreted as fully normative ("shall") for the purpose of compliance with the present document.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] Eurocontrol: Airport CDM Operational Concept Document (Version 3.1, Sept 2006).
NOTE: See figure 1.
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 303 212 V1.1.1 (2009-08)
[2] Eurocontrol: Airport CDM Functional Requirements Document (Version 4.0 May 2009).
NOTE: See figure 1.
[3] Eurocontrol: CFMU DPI Implementation Guide (Version 1.3).
NOTE: See figure 1.
[4] Eurocontrol: CFMU Flight Progress Messages (Version 1.6).
NOTE: See figure 1.
[5] Eurocae: Minimum Technical Specification for the Airport Collaborative Decision Making
(Airport-CDM) - ED141 - (Version 1, October 2008).
NOTE: See figure 1.
[6] Eurocae: Airport-CDM Interface Specification - ED145 - (Version 1, October 2008).
NOTE: See figure 1.
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Regulation (EC) No 552/2004 of the European Parliament and of the Council of 10 March 2004
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.