SIST EN ISO 9337-2:2005
(Main)Contact lenses - Determination of back vertex power - Part 2: Measurement of contact lenses immersed in saline (ISO 9337-2:2004)
Contact lenses - Determination of back vertex power - Part 2: Measurement of contact lenses immersed in saline (ISO 9337-2:2004)
Kontaktlinsen - Bestimmung des bildseitigen Scheitelbrechwertes - Teil 2: Kontaktlinsenmessung in Immersion (Kochsalzlösung) (ISO 9337-2:2004)
Dieser Teil von ISO 9337 beschreibt Prüfverfahren für die Bestimmung des bildseitigen Scheitelbrechwertes von weichen Kontaktlinsen in Immersion in Kochsalzlösung. Sie gilt für verkaufsfertige Kontaktlinsen (Endprodukte).
Lentilles de contact - Détermination de la puissance frontale arriere - Partie 2: Mesurage des lentilles de contact immergées dans une solution saline (ISO 9337-2:2004)
Contact lenses - Determination of back vertex power - Part 2: Measurement of contact lenses immersed in saline (ISO 9337-2:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9337-2:2005
01-januar-2005
Contact lenses - Determination of back vertex power - Part 2: Measurement of
contact lenses immersed in saline (ISO 9337-2:2004)
Contact lenses - Determination of back vertex power - Part 2: Measurement of contact
lenses immersed in saline (ISO 9337-2:2004)
Kontaktlinsen - Bestimmung des bildseitigen Scheitelbrechwertes - Teil 2:
Kontaktlinsenmessung in Immersion (Kochsalzlösung) (ISO 9337-2:2004)
Lentilles de contact - Détermination de la puissance frontale arriere - Partie 2: Mesurage
des lentilles de contact immergées dans une solution saline (ISO 9337-2:2004)
Ta slovenski standard je istoveten z: EN ISO 9337-2:2004
ICS:
11.040.70 Oftalmološka oprema Ophthalmic equipment
SIST EN ISO 9337-2:2005 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9337-2:2005
---------------------- Page: 2 ----------------------
SIST EN ISO 9337-2:2005
EUROPEAN STANDARD
EN ISO 9337-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 11.040.70
English version
Contact lenses - Determination of back vertex power - Part 2:
Measurement of contact lenses immersed in saline (ISO 9337-
2:2004)
Lentilles de contact - Détermination de la puissance Kontaktlinsen - Bestimmung des bildseitigen
frontale arrière - Partie 2: Mesurage des lentilles de contact Scheitelbrechwertes - Teil 2: Kontaktlinsenmessung in
immergées dans une solution saline (ISO 9337-2:2004) Immersion (Kochsalzlösung) (ISO 9337-2:2004)
This European Standard was approved by CEN on 15 June 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9337-2:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9337-2:2005
EN ISO 9337-2:2004 (E)
Foreword
This document (EN ISO 9337-2:2004) has been prepared by Technical Committee ISO/TC 172
"Optics and optical instruments" in collaboration with Technical Committee CEN/TC 170
"Ophthalmic optics", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2005, and conflicting national
standards shall be withdrawn at the latest by January 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 9337-2:2004 has been approved by CEN as EN ISO 9337-2:2004 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9337-2:2005
INTERNATIONAL ISO
STANDARD 9337-2
First edition
2004-07-15
Contact lenses — Determination of back
vertex power —
Part 2:
Measurement of contact lenses immersed
in saline
Lentilles de contact — Détermination de la puissance frontale arrière —
Partie 2: Mesurage des lentilles de contact immergées dans une
solution saline
Reference number
ISO 9337-2:2004(E)
©
ISO 2004
---------------------- Page: 5 ----------------------
SIST EN ISO 9337-2:2005
ISO 9337-2:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 9337-2:2005
ISO 9337-2:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9337-2 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 7,
Ophthalmic optics and instruments.
ISO 9337 consists of the following parts, under the general title Contact lenses — Determination of back
vertex power:
Part 1: Method using focimeter with manual focusing
Part 2: Measurement of contact lenses immersed in saline
© ISO 2004 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 9337-2:2005
ISO 9337-2:2004(E)
Introduction
It is intended that the test methods described in this part of ISO 9337 should be used by contact lens
manufacturers, practitioners and other interested parties.
It has been assumed in drafting this part of ISO 9337 that the execution of its provisions will be entrusted to
appropriately qualified and experienced people.
iv © ISO 2004 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 9337-2:2005
INTERNATIONAL STANDARD ISO 9337-2:2004(E)
Contact lenses — Determination of back vertex power —
Part 2:
Measurement of contact lenses immersed in saline
1 Scope
This part of ISO 9337 describes test methods for the determination of back vertex power of soft contact lenses
immersed in saline. It is applicable to finished contact lenses.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8320-1, Contact lenses and contact lens care products — Vocabulary — Part 1: Contact lenses
ISO 8320-2, Contact lenses and contact lens care products — Vocabulary — Part 2: Contact lens care
products
ISO 10344, Optics and optical instruments — Contact lenses — Saline solution for contact lens testing
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8320-1 and ISO 8320-2 apply.
4 Test methods
The test methods specified in Annex A are listed in Table 1, together with a statement of their reproducibility
when applied to spherical or toric soft contact lenses. Reproducibility of a method should be half or less of the
product tolerance in order to verify the tolerance.
© ISO 2004 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST EN ISO 9337-2:2005
ISO 9337-2:2004(E)
Table 1 — Test methods
Test method Application Reproducibility, R
Spherical soft lenses 0,252 8 D
Toric soft lenses:
Moiré deflectometer
Sphere power 0,442 1 D
Cylinder power 0,260 4 D
Axis direction 3,416°
Spherical soft lenses 0,070 8 D
Toric soft lenses:
Hartmann method
Sphere power 0,181 7 D
Cylinder power 0,243 9 D
Axis direction 5,644 8°
2 © ISO 2004 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 9337-2:2005
ISO 9337-2:2004(E)
Annex A
(normative)
Determination of back vertex power of contact lenses immersed in saline
A.1 Scope
This annex specifies a method for determining the back vertex power of soft contact lenses immersed in
saline using: (1) the Moiré deflectometer and (2) the Hartmann method.
A.2 Principle
The Moiré deflectometer is a quantitative instrument for mapping ray deflections of a beam passed through
or reflected off a test object. The technique is based on the Moiré effect, a phenomenon that causes a fringe
pattern to appear when two gratings are placed at a small angle to each other. The fringe pattern is detected
by a CCD camera and digitized. Digital information relating to the fringe pattern is relayed through the electro-
optical interface to the control software for analysis. The resulting image is displayed on a visual display unit.
The system is calibrated so that when there is no contact lens in the cuvette, the beam is collimated and
straight vertical fringes are observed. When a contact lens is inserted in the cuvette, the fringes deviate from
the vertical. The laser light source is tr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.