SIST ISO 888:2000

Bolts, screws and studs -- Nominal lengths, and thread lengths for general purpose bolts

Specifies the nominal lengths from 2 mm up to and including 300 mm as well as from 1/16 inch up to and including 12 inch resp.; gives the coordination for thread lengths/diameters for the dimensions in millimeters and inches.

Boulons, vis et goujons -- Longueurs de tige nominales, et longueurs filetées des boulons d'application générale

Sorniki, vijaki in zatiči - Imenske dožine in dolžine navoja za sornike za splošno uporabo

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-1996
• Withdrawal Date: 29-Jan-2015
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 27-Jan-2015
• Due Date: 19-Feb-2015
• Completion Date: 30-Jan-2015
• Ref Project: ISO 888:1976 - Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts

Relations

• Replaced By: SIST ISO 888:2015 - Fasteners - Bolts, screws and studs - Nominal lengths and thread lengths
• Effective Date: 01-Mar-2015

Standards Content (Sample)

INTERNATIONAL STANDARD
888
INTERNATIONAL ORGANIZATION FOR STANDARCIZATION .MEXC,‘IYHAPOAHAR OPf-AHM3AUMJl I-IO CTAHAAPTM3ALUiM.ORGANISATION INTERNATIONALE DE NORMALISATION
Nominal lengths, and thread lengths
Bolts, screws and studs -
for general purpose bolts
Longueurs de tige nominales, et longueurs filetdes des boulons d’application ghkale
Boulons, vis et goujons -
First edition - 1976-05-01
Ref. No. IS0 8884976 (E)
UDC 621.882.2-181.12
bolts, screws, studs, dimensions, threaded length.
Descriptors : fasteners,
Price based on 2 pages

---------------------- Page: 1 ----------------------
FOREWORD
IS0 (the International Organization for Standardization) is a worldwide federation
of national standards institutes (IS0 Member Bodies). The work of developing
International Standards is carried out through IS0 Technical Committees. Every
Member Body interested in a subject for which a Technical Committee has been set
up has the right to be represented on that Committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the Technical Committees are circulated
to the Member Bodies for approval before their acceptance as International
Standards by the IS0 Council.
Prior to 1972, the results of the work of the Technical Committees were published
as IS0 Recommendations; these documents are now in the process of being
transformed into International Standards. As part of this process, Technical
Committee lSO/TC 2 has reviewed IS0 Recommendation R 888 and found it
technically suitable for transformation. International Standard IS0 888 therefore
replaces IS0 Recommendation R 8884968 to which it is technically identical.
IS0 Recommendation R 888 was approved by the Member Bodies of the following
countries :
Portugal
Austria India
I ran Romania
Belgium
Canada Ireland South Africa, Rep. of
Chile Israel Spain
Sweden
Czechoslovakia Italy
Denmark Japan Switzerland
Egypt, Arab Rep. of Korea, Rep. of Thailand
Finland Netherlands Turkey
Germany New Zealand United Kingdom
Greece Norway U.S.S.R.
Yugoslavia
Hungary Poland
The Member Bodies of the following countries expressed disapproval of the
Recommendation on technical grounds :
France
U.S.A.
The Member Bodies of the following countries disapproved the transformation
of ISO/R 888 into an International Standard :
Canada
France
Japan
Netherlands
U.S.A.
0 International Organization for Standardization, 1976 l
Printed in Switzerland

---------------------- Page: 2 ----------------------
INTERNATIONAL STANDARD IS0 888-1976 (E)
Nominal lengths, and thread lengths
Bolts, screws and studs -
for general purpose bolts
slotted head screws, cross recess head screws) and studs of
1 SCOPE AND FIELD OF APPLICATION
both metric and inch sizes. Table 1 indicates the
This International Standard specifies nominal lengths for
comparable basic lengths in the two systems, but values are
bolts, screws and studs, and thread length
...

SLOVENSKI STANDARD
SIST ISO 888:2000
01-januar-2000
6RUQLNLYLMDNLLQ]DWLþL,PHQVNHGRåLQHLQGROåLQHQDYRMD]DVRUQLNH]DVSORãQR
XSRUDER
Bolts, screws and studs -- Nominal lengths, and thread lengths for general purpose bolts
Boulons, vis et goujons -- Longueurs de tige nominales, et longueurs filetées des
boulons d'application générale
Ta slovenski standard je istoveten z: ISO 888:1976
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST ISO 888:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 888:2000

---------------------- Page: 2 ----------------------

SIST ISO 888:2000
INTERNATIONAL STANDARD
888
INTERNATIONAL ORGANIZATION FOR STANDARCIZATION .MEXC,‘IYHAPOAHAR OPf-AHM3AUMJl I-IO CTAHAAPTM3ALUiM.ORGANISATION INTERNATIONALE DE NORMALISATION
Nominal lengths, and thread lengths
Bolts, screws and studs -
for general purpose bolts
Longueurs de tige nominales, et longueurs filetdes des boulons d’application ghkale
Boulons, vis et goujons -
First edition - 1976-05-01
Ref. No. IS0 8884976 (E)
UDC 621.882.2-181.12
bolts, screws, studs, dimensions, threaded length.
Descriptors : fasteners,
Price based on 2 pages

---------------------- Page: 3 ----------------------

SIST ISO 888:2000
FOREWORD
IS0 (the International Organization for Standardization) is a worldwide federation
of national standards institutes (IS0 Member Bodies). The work of developing
International Standards is carried out through IS0 Technical Committees. Every
Member Body interested in a subject for which a Technical Committee has been set
up has the right to be represented on that Committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the Technical Committees are circulated
to the Member Bodies for approval before their acceptance as International
Standards by the IS0 Council.
Prior to 1972, the results of the work of the Technical Committees were published
as IS0 Recommendations; these documents are now in the process of being
transformed into International Standards. As part of this process, Technical
Committee lSO/TC 2 has reviewed IS0 Recommendation R 888 and found it
technically suitable for transformation. International Standard IS0 888 therefore
replaces IS0 Recommendation R 8884968 to which it is technically identical.
IS0 Recommendation R 888 was approved by the Member Bodies of the following
countries :
Portugal
Austria India
I ran Romania
Belgium
Canada Ireland South Africa, Rep. of
Chile Israel Spain
Sweden
Czechoslovakia Italy
Denmark Japan Switzerland
Egypt, Arab Rep. of Korea, Rep. of Thailand
Finland Netherlands Turkey
Germany New Zealand United Kingdom
Greece Norway U.S.S.R.
Yugoslavia
Hungary Poland
The Member Bodies of the following countries expressed disapproval of the
Recommendation on technical grounds :
France
U.S.A.
The Member Bodies of the following countries disapproved the transformation
of ISO/R 888 into an International Standard :
Canada
France
Japan
Netherlands
U.S.A.
0 International Organization for Standardization, 1976 l
Printed in Switzerland

---------------------- Page: 4 ----------------------

SIST ISO 888:2000
INTERNATIONAL STANDARD IS0 888-1976 (E)
Nominal lengths
...

SLOVENSKI STANDARD
SIST ISO 888:
01-DSULO-
6RUQLNLYLMDNLLQ]DWLþL,PHQVNHGRåLQHLQGROåLQHQDYRMD]DVRUQLNH]DVSORãQR
XSRUDER
Bolts, screws and studs -- Nominal lengths, and thread lengths for general purpose bolts
Boulons, vis et goujons -- Longueurs de tige nominales, et longueurs filetées des
boulons d'application générale
Ta slovenski standard je istoveten z: ISO 888:1976
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST ISO 888: en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 888:1996

---------------------- Page: 2 ----------------------

SIST ISO 888:1996
INTERNATIONAL STANDARD
888
INTERNATIONAL ORGANIZATION FOR STANDARCIZATION .MEXC,‘IYHAPOAHAR OPf-AHM3AUMJl I-IO CTAHAAPTM3ALUiM.ORGANISATION INTERNATIONALE DE NORMALISATION
Nominal lengths, and thread lengths
Bolts, screws and studs -
for general purpose bolts
Longueurs de tige nominales, et longueurs filetdes des boulons d’application ghkale
Boulons, vis et goujons -
First edition - 1976-05-01
Ref. No. IS0 8884976 (E)
UDC 621.882.2-181.12
bolts, screws, studs, dimensions, threaded length.
Descriptors : fasteners,
Price based on 2 pages

---------------------- Page: 3 ----------------------

SIST ISO 888:1996
FOREWORD
IS0 (the International Organization for Standardization) is a worldwide federation
of national standards institutes (IS0 Member Bodies). The work of developing
International Standards is carried out through IS0 Technical Committees. Every
Member Body interested in a subject for which a Technical Committee has been set
up has the right to be represented on that Committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the Technical Committees are circulated
to the Member Bodies for approval before their acceptance as International
Standards by the IS0 Council.
Prior to 1972, the results of the work of the Technical Committees were published
as IS0 Recommendations; these documents are now in the process of being
transformed into International Standards. As part of this process, Technical
Committee lSO/TC 2 has reviewed IS0 Recommendation R 888 and found it
technically suitable for transformation. International Standard IS0 888 therefore
replaces IS0 Recommendation R 8884968 to which it is technically identical.
IS0 Recommendation R 888 was approved by the Member Bodies of the following
countries :
Portugal
Austria India
I ran Romania
Belgium
Canada Ireland South Africa, Rep. of
Chile Israel Spain
Sweden
Czechoslovakia Italy
Denmark Japan Switzerland
Egypt, Arab Rep. of Korea, Rep. of Thailand
Finland Netherlands Turkey
Germany New Zealand United Kingdom
Greece Norway U.S.S.R.
Yugoslavia
Hungary Poland
The Member Bodies of the following countries expressed disapproval of the
Recommendation on technical grounds :
France
U.S.A.
The Member Bodies of the following countries disapproved the transformation
of ISO/R 888 into an International Standard :
Canada
France
Japan
Netherlands
U.S.A.
0 International Organization for Standardization, 1976 l
Printed in Switzerland

---------------------- Page: 4 ----------------------

SIST ISO 888:1996
INTERNATIONAL STANDARD IS0 888-1976 (E)
N
...

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION .MEXJL'HAPO,rlHA5'I OPTAHM3AUMfl Il0 CTAHDAPTI-43AIIMM .ORGANISATION INTERNATIONALE DE NORMALISATION
Longueurs de tige nominales, et
Boulons, vis et goujons -
longueurs filetées des boulons d’application générale
Bolts, screws and studs - Nominal lengtbs, and thread tengths for general purpose bolts
Première édition - 1976-05-01
CDU 621.882.2-181.12 Réf. no : ISO 888-1976 (F)
Descripteurs : élément de fixation, boulon, vis, goujon, dimension, longueur filetée.
Prix basé sur 2 pages

---------------------- Page: 1 ----------------------
AVANT-PROPOS
lS0 (Organisation Internationale de Normalisation) est une fédération mondiale
d’organismes nationaux de normalisation (Comités Membres ISO). L’élaboration de
Normes Internationales est confiée aux Comités Techniques ISO. Chaque Comité
Membre intéressé par une étude a le droit de faire partie du Comité Technique
correspondant. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec I’ISO, participent également aux travaux.
Les Projets de Normes Internationales adoptés par les Comités Techniques sont
soumis aux Comités Membres pour approbation, avant leur acceptation comme
Normes Internationales par le Conseil de I’ISO.
Avant 1972, les résultats des travaux des Comités Techniques étaient publiés
comme Recommandations ISO; maintenant, ces documents sont en cours de
transformation en Normes Internationales. Compte tenu de cette procédure, le
Comité Technique lSO/TC 2 a examiné la Recommandation lSO/R 888 et est
d’avis qu’elle peut, du point de vue technique, être transformée en Norme
Internationale. La présente Norme Internationale remplace donc la
Recommandation lSO/R 888-1968 à laquelle elle est techniquement identique.
La Recommandation lSO/R 888 avait été approuvée par les Comités Membres des
pays suivants :
Afrique du Sud, Rép. d’ Grèce Pologne
Al lemagne Hongrie Portugal
Autriche Inde Roumanie
Belgique Iran Royaume-Uni
Canada Irlande Suède
Chili Israël Suisse
Corée, Rép. de Italie Tchécoslovaquie
Danemark Japon Thaïlande
Égypte, Rép. arabe d’ Norvège Turquie
Nouvelle-Zélande
Espagne U.R.S.S.
Finlande Pays-Bas Yougoslavie
Les Comités Membres des pays suivants avaient désapprouvé la Recommandation
pour des raisons techniques :
France
U.S.A.
Les Comités Membres des pays suivants ont désapprouvé la transformation de
la Recommandation lSO/R 888 en Norme Internationale :
Canada
France
Japon
Pays-Bas
U.S.A.
0 Organisation Internationale de Normalisation, 1976 l
Imprimé en Suisse

---------------------- Page: 2 ----------------------
NORME INTERNATIONALE ISO 888-1976 (F)
Longueurs de tige nominales, et
Boulons, vis et goujons -
longueurs f iletées des boulons d”application générale
1 OBJET ET DOMAINE D’APPLlCATION
fendue, vis à tête à empreinte cruciforme) et goujons en
dimensions métriques et en inches. Le tableau 1 indique les
La présente Norme Internationale fixe les longueurs de tige
longueurs nominales dans les deux systèmes de mesure,
nominales des boulons, vis et go
...

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION .MEXJL'HAPO,rlHA5'I OPTAHM3AUMfl Il0 CTAHDAPTI-43AIIMM .ORGANISATION INTERNATIONALE DE NORMALISATION
Longueurs de tige nominales, et
Boulons, vis et goujons -
longueurs filetées des boulons d’application générale
Bolts, screws and studs - Nominal lengtbs, and thread tengths for general purpose bolts
Première édition - 1976-05-01
CDU 621.882.2-181.12 Réf. no : ISO 888-1976 (F)
Descripteurs : élément de fixation, boulon, vis, goujon, dimension, longueur filetée.
Prix basé sur 2 pages

---------------------- Page: 1 ----------------------
AVANT-PROPOS
lS0 (Organisation Internationale de Normalisation) est une fédération mondiale
d’organismes nationaux de normalisation (Comités Membres ISO). L’élaboration de
Normes Internationales est confiée aux Comités Techniques ISO. Chaque Comité
Membre intéressé par une étude a le droit de faire partie du Comité Technique
correspondant. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec I’ISO, participent également aux travaux.
Les Projets de Normes Internationales adoptés par les Comités Techniques sont
soumis aux Comités Membres pour approbation, avant leur acceptation comme
Normes Internationales par le Conseil de I’ISO.
Avant 1972, les résultats des travaux des Comités Techniques étaient publiés
comme Recommandations ISO; maintenant, ces documents sont en cours de
transformation en Normes Internationales. Compte tenu de cette procédure, le
Comité Technique lSO/TC 2 a examiné la Recommandation lSO/R 888 et est
d’avis qu’elle peut, du point de vue technique, être transformée en Norme
Internationale. La présente Norme Internationale remplace donc la
Recommandation lSO/R 888-1968 à laquelle elle est techniquement identique.
La Recommandation lSO/R 888 avait été approuvée par les Comités Membres des
pays suivants :
Afrique du Sud, Rép. d’ Grèce Pologne
Al lemagne Hongrie Portugal
Autriche Inde Roumanie
Belgique Iran Royaume-Uni
Canada Irlande Suède
Chili Israël Suisse
Corée, Rép. de Italie Tchécoslovaquie
Danemark Japon Thaïlande
Égypte, Rép. arabe d’ Norvège Turquie
Nouvelle-Zélande
Espagne U.R.S.S.
Finlande Pays-Bas Yougoslavie
Les Comités Membres des pays suivants avaient désapprouvé la Recommandation
pour des raisons techniques :
France
U.S.A.
Les Comités Membres des pays suivants ont désapprouvé la transformation de
la Recommandation lSO/R 888 en Norme Internationale :
Canada
France
Japon
Pays-Bas
U.S.A.
0 Organisation Internationale de Normalisation, 1976 l
Imprimé en Suisse

---------------------- Page: 2 ----------------------
NORME INTERNATIONALE ISO 888-1976 (F)
Longueurs de tige nominales, et
Boulons, vis et goujons -
longueurs f iletées des boulons d”application générale
1 OBJET ET DOMAINE D’APPLlCATION
fendue, vis à tête à empreinte cruciforme) et goujons en
dimensions métriques et en inches. Le tableau 1 indique les
La présente Norme Internationale fixe les longueurs de tige
longueurs nominales dans les deux systèmes de mesure,
nominales des boulons, vis et go
...