SIST ETS 300 765-2:1999
(Main)Digital Enhanced Cordless Telecommunications (DECT); Radio in the Local Loop (RLL) Access Profile (RAP); Part 2: Advanced telephony services
Digital Enhanced Cordless Telecommunications (DECT); Radio in the Local Loop (RLL) Access Profile (RAP); Part 2: Advanced telephony services
To produce an interoperability air-interface profile for DECT-RLL application: RAP (RLL Access Profile), based on the DECT Generic Access Profile (GAP), providing a minimum of service level, i.e. the so called POTS services, and optional extensions including 64 kbit/s bearer service, ISDN services and broadband packet services.
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Radio v krajevni zanki (RLL) dostopovni profil (RAP) - 2. del: Napredne telefonske storitve
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WYHDigital Enhanced Cordless Telecommunications (DECT); Radio in the Local Loop (RLL) Access Profile (RAP); Part 2: Advanced telephony services33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 765-2 Edition 13SIST ETS 300 765-2:1999en01-PDUHF-19993SIST ETS 300 765-2:1999SLOVENSKI
STANDARD
SIST ETS 300 765-2:1999
EUROPEANETS 300 765-2TELECOMMUNICATIONApril 1998STANDARDSource: DECTReference: DE/DECT-050075-2ICS:33.020Key words:DECT, GSM, RLLDigital Enhanced Cordless Telecommunications (DECT);Radio in the Local Loop (RLL) Access Profile (RAP);Part 2: Advanced telephony servicesETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEInternet: secretariat@etsi.fr - http://www.etsi.fr - http://www.etsi.orgTel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1998. All rights reserved.SIST ETS 300 765-2:1999
Page 2ETS 300 765-2: April 1998Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 765-2:1999
Page 3ETS 300 765-2: April 1998ContentsForeword.51Scope.72Normative references.73Definitions, abbreviations and symbols.93.1DECT definitions.93.2DECT abbreviations.123.3ISDN abbreviations.133.4Other abbreviations.133.5Symbols.134Description of services.144.1Reference model.144.2Services & facilities.144.2.1ISDN services.144.2.2Non-voiceband data services.154.2.2.1LAN service.154.2.2.2Internet access.164.2.2.2.1IP transport service.164.2.2.2.2Internet over Point-to-Point Protocol(PPP) service.164.2.2.3Modem.164.2.2.4Group 3 facsimile.165Feature definitions.175.1Network (NWK) features.175.1.1DECT CTA OA&M features.175.1.2ISDN CTA specific OA&M features.176Interoperability requirements.186.1General.186.2NWK features.186.2.1General.186.2.2OA&M features.186.3DLC services.196.3.1General.196.4MAC services.196.4.1General.196.4.2Blind slot information.196.4.3Improved channel selection rules.196.4.4Advance timing.206.5Physical Layer (PHL) services.206.5.1General.206.6NWK feature to procedure mapping.217NWK layer procedures.237.1Maintenance calls.237.1.1Maintenance calls within the data profiles.237.1.1.1Incoming maintenance call.237.1.1.2Outgoing maintenance call.237.1.1.3Outgoing call during maintenance call.237.1.1.4Incoming call during maintenance call.237.1.2Maintenance calls within the IIP.237.1.2.1Incoming maintenance call.237.1.2.2Outgoing maintenance call.23SIST ETS 300 765-2:1999
Page 4ETS 300 765-2: April 19987.2Sending OA&M information.247.2.1Physical resources fault.247.2.2Remote test.247.2.3Alarms.257.2.4On-air modification of user parameters.257.2.4.1Modification of existing users parameters.257.2.4.2Additional subscriptions to the same fixed part.267.2.4.3Derivation of AC for additional subscriptions.267.2.5Remote configuration.277.2.6Claim actions.287.2.7Remote resynchronization.287.2.8Advanced file transfer.297.3WRS maintenance calls.307.3.1Incoming WRS maintenance call.307.3.2Outgoing WRS maintenance call.307.3.3Maintenance during WRS MM operation.30Annex A (informative):ETS 300 175-5 changes.31Annex B (normative):Codings for "OA&M" messages.33B.1General Structure for RAP <> IE.33B.2RAP-OA&M IWU-TO-IWU Contents Proprietary.34B.3RAP-OA&M IWU-TO-IWU Contents Standardized.35Annex C (informative):CTA data port realizations.38Annex D (normative):Interworking with WRSs.39D.1Definitions of features, services and procedures.39D.1.1NWK features.39D.1.2MAC services.39D.2Interoperability requirements.40D.2.1NWK features.40D.2.2DLC services.41D.2.3MAC services.41D.2.4PHL services.42D.2.5NWK feature to procedure mapping.43D.2.6MAC service to procedure mapping.45D.3NWK layer procedures.46D.3.1NWK layer transparency between FT and PT.46D.3.2Cipher key transfer to CRFP.46D.4MAC layer procedures.46D.4.1Extended Fixed Part capabilities.46D.4.2Hop control.46D.4.3Normal C/O bearer set-up.46D.4.4Dual C/O bearer set-up.46D.4.5CRFP connection suspend and resume.47D.4.6CRFP C/O release.47D.4.7Bearer handover request.47D.4.8Connection handover request.47Annex E (normative):Synchronization requirements for fixed parts.48History.49SIST ETS 300 765-2:1999
Page 5ETS 300 765-2: April 1998ForewordThis European Telecommunication Standard (ETS) has been produced by the Digital Enhanced CordlessTelecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).Every ETS prepared by ETSI is a voluntary standard. This ETS may contain text concerning conformancetesting of the equipment to which it relates. This text should be considered as guidance only and does notmake this ETS mandatory.This ETS is based on ETS 300 175 parts 1 to 8 [1] - [8], EN 300 444 [13], ETS 300 822 [19],ETS 300 701 [21], ETS 300 651 [22] and ETS 300 755 [23]. This ETS has been developed in accordanceto the rules of documenting a profile specification as described in ISO/IEC 9646-6 [11].This ETS forms part 2 of a 2 part ETS, as follows:Part 1:"Basic telephony services";Part 2:"Advanced telephony services".Transposition datesDate of adoption of this ETS:20 March 1998Date of latest announcement of this ETS (doa):31 July 1998Date of latest publication of new National Standardor endorsement of this ETS (dop/e):31 January 1999Date of withdrawal of any conflicting National Standard (dow):31 January 1999SIST ETS 300 765-2:1999
Page 6ETS 300 765-2: April 1998Blank pageSIST ETS 300 765-2:1999
Page 7ETS 300 765-2: April 19981ScopeThis European Telecommunication Standard (ETS) specifies that set of technical requirements for DigitalEnhanced Cordless Telecommunications (DECT) Fixed Part (FP) and DECT Cordless Terminal Adapter(CTA) for the support of the Radio in the Local Loop (RLL) Access Profile (RAP).The objective of this ETS is to ensure the air interface interoperability of DECT RAP CTAs and DECTRAP FPs and Wireless Relay Stations (WRSs) if applied.ETS 300 765-1 [16] contains the so called "Plain Old Telephone Service (POTS)" services includinganalogue leased lines and 64 kbit/s bearer service. ETS 300 765-1 [16] also provides for optional mobilityfeatures by supporting Generic Access Profile (GAP) Portable Part (PP) subscriber terminals and CTAswith WRS GAP functionality.This ETS contains telecommunication services as offered by Integrated Services Digital Network (ISDN),contemporary non-voiceband data services provided through, for example, a dedicated data port at theCTA, and support of digital leased lines. The provision of the mentioned services is not mandated by thisETS, but if provided they shall be provided as defined (provision optional, process mandatory).An objective is to use as much as possible from existing profiles: DECT/ISDN Intermediate ISDN accessProfile (IIP) as defined in ETS 300 822 [19] and the data profile A/B.2 as defined in ETS 300 701 [21],data profile C.2 as defined in ETS 300 651 [22], and data profile F.2 as defined in ETS 300 755 [23].Therefore, most of the RAP features refer to features defined in other profiles and the necessaryadditional features (e.g. Operation, Administration and Maintenance (OA&M)) are listed and explained inthis ETS.In addition, this ETS defines additional features, services, procedures, etc. for the CTA and the FT, whichare provision mandatory either in the CTA or in the FT, as well as some elements that are provisionoptional but still process mandatory. These features in particular define the operation and maintenance ofCTAs in relation to the provided service (profile) in a public network.2Normative referencesThis ETS incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this ETS only when incorporated in it by amendment or revision. For undated references the latestedition of the publication referred to applies.[1]ETS 300 175-1: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 1: Overview".[2]ETS 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 2: Physical layer (PHL)".[3]ETS 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 3: Medium Access Control (MAC) layer".[4]ETS 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 4: Data Link Control (DLC) layer".[5]ETS 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 5: Network (NWK) layer".[6]ETS 300 175-6: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 6: Identities and addressing".[7]ETS 300 175-7: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 7: Security features".[8]ETS 300 175-8: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 8: Speech coding and transmission".SIST ETS 300 765-2:1999
Page 8ETS 300 765-2: April 1998[9]I-ETS 300 176: "Digital Enhanced Cordless Telecommunications (DECT);Approval test specification".[10]TBR 6: "Radio Equipment and Systems (RES); Digital Enhanced CordlessTelecommunications (DECT); General terminal attachment requirements".[11]ISO/IEC 9646-6: "Information technology - Open Systems Interconnection -Conformance testing methodology and framework - Part 6: Protocol profile testspecification".[12]ISO/IEC 9646-7: "Information technology - Open Systems Interconnection -Conformance testing methodology and framework - Part 7: Implementationconformance statement".[13]EN 300 444: "Digital Enhanced Cordless Telecommunications (DECT); GenericAccess Profile (GAP)".[14]ETR 056: "Digital European Cordless Telecommunications (DECT); Systemdescription document".[15]ETS 300 700: "Digital European Cordless Telecommunications (DECT);Wireless Relay Station (WRS)".[16]ETS 300 765-1: "Digital Enhanced Cordless Telecommunications (DECT);Radio in the Local Loop (RLL) Access Profile (RAP); Part 1: Basic telephonyservices".[17]ETR 246: "Digital European Cordless Telecommunications (DECT); Applicationof DECT Wireless Relay Station (WRS)".[18]ETR 310: "Digital Enhanced Cordless Telecommunications (DECT); Trafficcapacity and spectrum requirements for multi-system and multi-service DECTapplications co-existing in a common frequency band".[19]ETS 300 822: "Digital Enhanced Cordless Telecommunications (DECT);Integrated Services Digital Network (ISDN); DECT/ISDN interworking forintermediate system configuration; Interworking and profile specification".[20]ITU-T Recommendation I.411: (1993): "ISDN user-network interfaces -Reference configurations".[21]ETS 300 701: "Digital Enhanced Cordless Telecommunications (DECT); DataServices Profile (DSP); Generic frame relay service with mobility (service typesA and B, class 2)".[22]ETS 300 651: "Digital Enhanced Cordless Telecommunications (DECT); DataServices Profile (DSP); Generic data link service; Service type C, class 2".[23]ETS 300 755: "Digital Enhanced Cordless Telecommunications (DECT); Dataservices profile; Multimedia Messaging Service (MMS) with specific provision forfacsimile services; (Service type F, class 2)".[24]ETR 185: "Digital European Cordless Telecommunications (DECT); DataServices Profile (DSP); Profile overview".[25]ETS 300 297: "Integrated Services Digital Network (ISDN); Access digitalsection for ISDN basic access".[26]EN 301 240: "Digital Enhanced Cordless Telecommunications (DECT); DataServices Profile (DSP); Point-to-Point Protocol (PPP) interworking for internetaccess and general multi-protocol datagram transport".SIST ETS 300 765-2:1999
Page 9ETS 300 765-2: April 1998[27]RFC 1661 (1994): "The Point-to-Point Protocol (PPP)".[28]RFC 1662 (1994): "PPP in HDLC-like Framing".[29]ISO 8802: "Information technology -- Telecommunications and informationexchange between systems -- Local and metropolitan area networks -- Specificrequirements".3Definitions, abbreviations and symbols3.1DECT definitionsFor the purposes of this ETS, the following definitions apply:authentication: The process whereby a DECT subscriber is positively verified to be a legitimate user of aparticular FP.NOTE 1:Authentication is generally performed at call set-up, but may also be done at any othertime (e.g. during a call).bearer service: A type of telecommunication service that provides a defined capability for thetransmission of signals between user-network interfaces.NOTE 2:The DECT user-network interface corresponds to the top of the network layer (layer 3).C-plane: The control plane of the DECT protocol stacks, which contains all of the internal DECT protocolcontrol, but may also include some external user information.NOTE 3:The C-plane stack always contains protocol entities up to and including the networklayer.call: All of the Network (NWK) layer processes involved in one network layer peer-to-peer association.NOTE 4:Call may sometimes be used to refer to processes of all layers, since lower layerprocesses are implicitly required.Cordless Terminal Adapter (CTA): Physical grouping that contains a DECT portable termination and aline interface.Fixed Part (DECT Fixed Part) (FP): A physical grouping that contains all of the elements in the DECTnetwork between the local network and the DECT air interface.NOTE 5:A DECT FP contains the logical elements of at least one FT, plus additionalimplementation specific elements.DECT network: A network that uses the DECT air interface to interconnect a local network to one ormore portable applications. The logical boundaries of the DECT network are defined to be at the top of theDECT network layer.NOTE 6:A DECT Network is a logical grouping that contains one or more fixed radioterminations plus their associated portable radio termination. The boundaries of theDECT network are not physical boundaries.DECT intermediate fixed system: A logical grouping that contains all the functions between the DECT DIreference point and the reference point on the fixed side of the DECT air interface.NOTE 7:The DECT Intermediate Fixed System (DIFS) = FT + (local network up to the fixedside ISDN reference point (including fixed side Interworking Unit (IWU))), seeETR 056 [14].DECT intermediate portable system: A logical grouping that contains all the functions between theDECT DI reference point and the ISDN S reference point on the portable side of the DECT air interface.SIST ETS 300 765-2:1999
Page 10ETS 300 765-2: April 1998NOTE 8:The DECT Intermediate Portable System (DIPS) = Portable radio Termination (PT) +(Portable Application (PA) up to the portable side ISDN S reference point (includingportable side IWU)), see ETR 056 [14].Fixed Radio Termination (FT): A logical group of functions that contains all of the DECT processes andprocedures on the fixed side of the DECT air interface.NOTE 9:A FT only includes elements that are defined in the DECT Common Interface (CI)standard. This includes radio transmission elements together with a selection of layer2 and layer 3 elements.handover: The process of switching a call in progress from one physical channel to another physicalchannel.NOTE 10:There are two physical forms of handover, intra-cell handover and inter-cell handover.incoming call: A call received at a CTA.inter-cell handover: The switching of a call in progress from one cell to another cell.internal handover: Handover processes that are completely internal to one FT. Internal handoverreconnects the call at the lower layers, while maintaining the call at the NWK layer.NOTE 11:The lower layer reconnection can either be at the Data Link Control (DLC) layer(connection handover) or at the MAC layer (bearer handover).interoperability: The capability of FPs and CTAs, that enable a CTA to obtain access to teleservices inmore than one location area and/or from more than one operator (more than one service provider).Interworking Unit (IWU): A unit that is used to interconnect subnetworks.NOTE 12:The IWU will contain the interworking functions necessary to support the requiredsubnetwork interworking.intra-cell handover: The switching of a call in progress from one physical channel of one cell to anotherphysical channel of the same cell.Local Network (LNW): A telecommunication network capable of offering local telecommunicationservices.NOTE 13:The term does not include legal or regulatory aspects, nor does it indicate if thenetwork is a public network or a private network.location area: The domain in which a CTA may receive (and/or make) calls as a result of a singlelocation registration.location registration: The process whereby the position of a DECT PT is determined to the level of onelocation area, and this position is updated in one or more databases.NOTE 14:These databases are not included within a DECT FT.MAC Connection (CONNECTION): An association between one source MAC Multi-Bearer Control(MBC) entity and one destination MAC MBC entity. This provides a set of related MAC services (a set oflogical channels), and it can involve one or more underlying MAC bearers.mobility class 1: Local area applications, for which terminals are pre-registered off-air with one or morespecific fixed parts, and establishment of service and user parameters is therefore implicit, according to aprofile-defined list.mobility class 2: Private and Public roaming applications for which terminals may move between fixedparts within a given domain and for which association of service parameters is explicit at the time ofservice request.SIST ETS 300 765-2:1999
Page 11ETS 300 765-2: April 1998outgoing call: A call originating from a CTA.Portable Application (PA): A logical grouping that contains all the elements that lie beyond the DECTnetwork boundary on the portable side.NOTE 15:The functions contained in the PA may be physically distributed, but any suchdistribution is invisible to the DECT network.Portable Part (DECT Portable Part) (PP): A physical grouping that contains all elements between theuser and the DECT air interface. PP is a generic term that may describe one or several physical pieces.NOTE 16:A DECT PP is logically divided into one PT plus one or more PAs.Portable radio Termination (PT): A logical group of functions that contains all of the DECT processesand procedures on the portable side of the DECT air interface.NOTE 17:A PT only includes elements that are defined in the DECT CI standard. This includesradio transmission elements (layer 1) together with a selection of layer 2 and layer 3elements.Radio Fixed Part (RFP): One physical sub-group of a FP that contains all the radio end points (one ormore) that are connected to a single system of antennas.registration: An ambiguous term, that should always be qualified. See either location registration orsubscription registration.service type A: Low speed frame relay, with a net sustainable throughput of up to 24 kbits/s, optimizedfor bursty data, low power consumption and low complexity applications such as hand-portableequipment.service type B: High performance frame relay, with a net sustainable throughput of up to 552 kbits/s,optimized for high speed and low latency with bursty data. Equipment implementation the Type B profileshall inter-operate with Type A equipment.service type C: Non-transparent connection of data streams requiring Link Access Protocol (LAP)services, optimized for high reliability and low additional complexity. This builds upon the services offeredby the type A or B profiles.service type E: A short message transfer or paging service which may be unacknowledged oracknowledged, optimized for small Service Data Units (SDUs), low PP complexity and ultra-low powerconsumption.service type F: An application profile specifically supporting teleservices such as fax, building upon theservices offered by the type A/B and C profiles, optimized for terminal simplicity, spectrum efficiency andnetwork flexibility.subscription registration: The infrequent process whereby a subscriber obtains access rights to one ormore FPs.NOTE 18:Subscription registration is usually required before a user can make or receive calls.SIST ETS 300 765-2:1999
Page 12ETS 300 765-2: April 1998Wireless Relay Station (WRS): A physical grouping that combines elements of both PTs and FTs torelay information on a physical channel from one DECT termination to a physical channel to anotherDECT termination.NOTE 19: The DECT termination can be a PT or a FT or another WRS.3.2DECT abbreviationsFor the purposes of this ETS, the following abbreviations apply:ACAuthentication CodeARCAccess Rights ClassARDAccess Rights DetailsARIAccess Rights IdentityC/LConnectionlessC/OConnection OrientedCCCall ControlCICommon InterfaceCPECustomer Premises EquipmentCTACordless Terminal AdapterDCKDerived Cipher KeyDECTDigital Enhanced Cordless TelecommunicationsDIFSDECT Intermediate Fixed SystemDIPSDECT In
...
SLOVENSKI STANDARD
SIST ETS 300 765-2:1999
01-julij-1999
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH '(&7 5DGLRYNUDMHYQL]DQNL
5// GRVWRSRYQLSURILO 5$3 GHO 1DSUHGQHWHOHIRQVNHVWRULWYH
Digital Enhanced Cordless Telecommunications (DECT); Radio in the Local Loop (RLL)
Access Profile (RAP); Part 2: Advanced telephony services
Ta slovenski standard je istoveten z: ETS 300 765-2 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
SIST ETS 300 765-2:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ETS 300 765-2:1999
---------------------- Page: 2 ----------------------
SIST ETS 300 765-2:1999
EUROPEAN ETS 300 765-2
TELECOMMUNICATION April 1998
STANDARD
Source: DECT Reference: DE/DECT-050075-2
ICS: 33.020
Key words: DECT, GSM, RLL
Digital Enhanced Cordless Telecommunications (DECT);
Radio in the Local Loop (RLL) Access Profile (RAP);
Part 2: Advanced telephony services
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: secretariat@etsi.fr - http://www.etsi.fr - http://www.etsi.org
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1998. All rights reserved.
---------------------- Page: 3 ----------------------
SIST ETS 300 765-2:1999
Page 2
ETS 300 765-2: April 1998
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.
---------------------- Page: 4 ----------------------
SIST ETS 300 765-2:1999
Page 3
ETS 300 765-2: April 1998
Contents
Foreword .5
1 Scope .7
2 Normative references.7
3 Definitions, abbreviations and symbols.9
3.1 DECT definitions.9
3.2 DECT abbreviations.12
3.3 ISDN abbreviations.13
3.4 Other abbreviations.13
3.5 Symbols .13
4 Description of services .14
4.1 Reference model .14
4.2 Services & facilities.14
4.2.1 ISDN services.14
4.2.2 Non-voiceband data services.15
4.2.2.1 LAN service .15
4.2.2.2 Internet access .16
4.2.2.2.1 IP transport service.16
4.2.2.2.2 Internet over Point-to-Point Protocol
(PPP) service.16
4.2.2.3 Modem.16
4.2.2.4 Group 3 facsimile.16
5 Feature definitions.17
5.1 Network (NWK) features.17
5.1.1 DECT CTA OA&M features.17
5.1.2 ISDN CTA specific OA&M features.17
6 Interoperability requirements.18
6.1 General .18
6.2 NWK features .18
6.2.1 General.18
6.2.2 OA&M features.18
6.3 DLC services.19
6.3.1 General.19
6.4 MAC services.19
6.4.1 General.19
6.4.2 Blind slot information.19
6.4.3 Improved channel selection rules.19
6.4.4 Advance timing.20
6.5 Physical Layer (PHL) services .20
6.5.1 General.20
6.6 NWK feature to procedure mapping.21
7 NWK layer procedures .23
7.1 Maintenance calls .23
7.1.1 Maintenance calls within the data profiles.23
7.1.1.1 Incoming maintenance call.23
7.1.1.2 Outgoing maintenance call .23
7.1.1.3 Outgoing call during maintenance call.23
7.1.1.4 Incoming call during maintenance call.23
7.1.2 Maintenance calls within the IIP .23
7.1.2.1 Incoming maintenance call.23
7.1.2.2 Outgoing maintenance call .23
---------------------- Page: 5 ----------------------
SIST ETS 300 765-2:1999
Page 4
ETS 300 765-2: April 1998
7.2 Sending OA&M information. 24
7.2.1 Physical resources fault. 24
7.2.2 Remote test . 24
7.2.3 Alarms. 25
7.2.4 On-air modification of user parameters . 25
7.2.4.1 Modification of existing users parameters . 25
7.2.4.2 Additional subscriptions to the same fixed part. 26
7.2.4.3 Derivation of AC for additional subscriptions . 26
7.2.5 Remote configuration. 27
7.2.6 Claim actions . 28
7.2.7 Remote resynchronization . 28
7.2.8 Advanced file transfer. 29
7.3 WRS maintenance calls. 30
7.3.1 Incoming WRS maintenance call . 30
7.3.2 Outgoing WRS maintenance call. 30
7.3.3 Maintenance during WRS MM operation. 30
Annex A (informative): ETS 300 175-5 changes . 31
Annex B (normative): Codings for "OA&M" messages. 33
B.1 General Structure for RAP <> IE. 33
B.2 RAP-OA&M IWU-TO-IWU Contents Proprietary. 34
B.3 RAP-OA&M IWU-TO-IWU Contents Standardized . 35
Annex C (informative): CTA data port realizations . 38
Annex D (normative): Interworking with WRSs. 39
D.1 Definitions of features, services and procedures. 39
D.1.1 NWK features. 39
D.1.2 MAC services . 39
D.2 Interoperability requirements . 40
D.2.1 NWK features. 40
D.2.2 DLC services. 41
D.2.3 MAC services . 41
D.2.4 PHL services . 42
D.2.5 NWK feature to procedure mapping . 43
D.2.6 MAC service to procedure mapping. 45
D.3 NWK layer procedures . 46
D.3.1 NWK layer transparency between FT and PT. 46
D.3.2 Cipher key transfer to CRFP . 46
D.4 MAC layer procedures . 46
D.4.1 Extended Fixed Part capabilities. 46
D.4.2 Hop control. 46
D.4.3 Normal C/O bearer set-up. 46
D.4.4 Dual C/O bearer set-up .46
D.4.5 CRFP connection suspend and resume . 47
D.4.6 CRFP C/O release . 47
D.4.7 Bearer handover request. 47
D.4.8 Connection handover request . 47
Annex E (normative): Synchronization requirements for fixed parts . 48
History. 49
---------------------- Page: 6 ----------------------
SIST ETS 300 765-2:1999
Page 5
ETS 300 765-2: April 1998
Foreword
This European Telecommunication Standard (ETS) has been produced by the Digital Enhanced Cordless
Telecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).
Every ETS prepared by ETSI is a voluntary standard. This ETS may contain text concerning conformance
testing of the equipment to which it relates. This text should be considered as guidance only and does not
make this ETS mandatory.
This ETS is based on ETS 300 175 parts 1 to 8 [1] - [8], EN 300 444 [13], ETS 300 822 [19],
ETS 300 701 [21], ETS 300 651 [22] and ETS 300 755 [23]. This ETS has been developed in accordance
to the rules of documenting a profile specification as described in ISO/IEC 9646-6 [11].
This ETS forms part 2 of a 2 part ETS, as follows:
Part 1: "Basic telephony services";
Part 2: "Advanced telephony services".
Transposition dates
Date of adoption of this ETS: 20 March 1998
Date of latest announcement of this ETS (doa): 31 July 1998
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 January 1999
Date of withdrawal of any conflicting National Standard (dow): 31 January 1999
---------------------- Page: 7 ----------------------
SIST ETS 300 765-2:1999
Page 6
ETS 300 765-2: April 1998
Blank page
---------------------- Page: 8 ----------------------
SIST ETS 300 765-2:1999
Page 7
ETS 300 765-2: April 1998
1 Scope
This European Telecommunication Standard (ETS) specifies that set of technical requirements for Digital
Enhanced Cordless Telecommunications (DECT) Fixed Part (FP) and DECT Cordless Terminal Adapter
(CTA) for the support of the Radio in the Local Loop (RLL) Access Profile (RAP).
The objective of this ETS is to ensure the air interface interoperability of DECT RAP CTAs and DECT
RAP FPs and Wireless Relay Stations (WRSs) if applied.
ETS 300 765-1 [16] contains the so called "Plain Old Telephone Service (POTS)" services including
analogue leased lines and 64 kbit/s bearer service. ETS 300 765-1 [16] also provides for optional mobility
features by supporting Generic Access Profile (GAP) Portable Part (PP) subscriber terminals and CTAs
with WRS GAP functionality.
This ETS contains telecommunication services as offered by Integrated Services Digital Network (ISDN),
contemporary non-voiceband data services provided through, for example, a dedicated data port at the
CTA, and support of digital leased lines. The provision of the mentioned services is not mandated by this
ETS, but if provided they shall be provided as defined (provision optional, process mandatory).
An objective is to use as much as possible from existing profiles: DECT/ISDN Intermediate ISDN access
Profile (IIP) as defined in ETS 300 822 [19] and the data profile A/B.2 as defined in ETS 300 701 [21],
data profile C.2 as defined in ETS 300 651 [22], and data profile F.2 as defined in ETS 300 755 [23].
Therefore, most of the RAP features refer to features defined in other profiles and the necessary
additional features (e.g. Operation, Administration and Maintenance (OA&M)) are listed and explained in
this ETS.
In addition, this ETS defines additional features, services, procedures, etc. for the CTA and the FT, which
are provision mandatory either in the CTA or in the FT, as well as some elements that are provision
optional but still process mandatory. These features in particular define the operation and maintenance of
CTAs in relation to the provided service (profile) in a public network.
2 Normative references
This ETS incorporates, by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies.
[1] ETS 300 175-1: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 1: Overview".
[2] ETS 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 2: Physical layer (PHL)".
[3] ETS 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 3: Medium Access Control (MAC) layer".
[4] ETS 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 4: Data Link Control (DLC) layer".
[5] ETS 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 5: Network (NWK) layer".
[6] ETS 300 175-6: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 6: Identities and addressing".
[7] ETS 300 175-7: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 7: Security features".
[8] ETS 300 175-8: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 8: Speech coding and transmission".
---------------------- Page: 9 ----------------------
SIST ETS 300 765-2:1999
Page 8
ETS 300 765-2: April 1998
[9] I-ETS 300 176: "Digital Enhanced Cordless Telecommunications (DECT);
Approval test specification".
[10] TBR 6: "Radio Equipment and Systems (RES); Digital Enhanced Cordless
Telecommunications (DECT); General terminal attachment requirements".
[11] ISO/IEC 9646-6: "Information technology - Open Systems Interconnection -
Conformance testing methodology and framework - Part 6: Protocol profile test
specification".
[12] ISO/IEC 9646-7: "Information technology - Open Systems Interconnection -
Conformance testing methodology and framework - Part 7: Implementation
conformance statement".
[13] EN 300 444: "Digital Enhanced Cordless Telecommunications (DECT); Generic
Access Profile (GAP)".
[14] ETR 056: "Digital European Cordless Telecommunications (DECT); System
description document".
[15] ETS 300 700: "Digital European Cordless Telecommunications (DECT);
Wireless Relay Station (WRS)".
[16] ETS 300 765-1: "Digital Enhanced Cordless Telecommunications (DECT);
Radio in the Local Loop (RLL) Access Profile (RAP); Part 1: Basic telephony
services".
[17] ETR 246: "Digital European Cordless Telecommunications (DECT); Application
of DECT Wireless Relay Station (WRS)".
[18] ETR 310: "Digital Enhanced Cordless Telecommunications (DECT); Traffic
capacity and spectrum requirements for multi-system and multi-service DECT
applications co-existing in a common frequency band".
[19] ETS 300 822: "Digital Enhanced Cordless Telecommunications (DECT);
Integrated Services Digital Network (ISDN); DECT/ISDN interworking for
intermediate system configuration; Interworking and profile specification".
[20] ITU-T Recommendation I.411: (1993): "ISDN user-network interfaces -
Reference configurations".
[21] ETS 300 701: "Digital Enhanced Cordless Telecommunications (DECT); Data
Services Profile (DSP); Generic frame relay service with mobility (service types
A and B, class 2)".
[22] ETS 300 651: "Digital Enhanced Cordless Telecommunications (DECT); Data
Services Profile (DSP); Generic data link service; Service type C, class 2".
[23] ETS 300 755: "Digital Enhanced Cordless Telecommunications (DECT); Data
services profile; Multimedia Messaging Service (MMS) with specific provision for
facsimile services; (Service type F, class 2)".
[24] ETR 185: "Digital European Cordless Telecommunications (DECT); Data
Services Profile (DSP); Profile overview".
[25] ETS 300 297: "Integrated Services Digital Network (ISDN); Access digital
section for ISDN basic access".
[26] EN 301 240: "Digital Enhanced Cordless Telecommunications (DECT); Data
Services Profile (DSP); Point-to-Point Protocol (PPP) interworking for internet
access and general multi-protocol datagram transport".
---------------------- Page: 10 ----------------------
SIST ETS 300 765-2:1999
Page 9
ETS 300 765-2: April 1998
[27] RFC 1661 (1994): "The Point-to-Point Protocol (PPP)".
[28] RFC 1662 (1994): "PPP in HDLC-like Framing".
[29] ISO 8802: "Information technology -- Telecommunications and information
exchange between systems -- Local and metropolitan area networks -- Specific
requirements".
3 Definitions, abbreviations and symbols
3.1 DECT definitions
For the purposes of this ETS, the following definitions apply:
authentication: The process whereby a DECT subscriber is positively verified to be a legitimate user of a
particular FP.
NOTE 1: Authentication is generally performed at call set-up, but may also be done at any other
time (e.g. during a call).
bearer service: A type of telecommunication service that provides a defined capability for the
transmission of signals between user-network interfaces.
NOTE 2: The DECT user-network interface corresponds to the top of the network layer (layer 3).
C-plane: The control plane of the DECT protocol stacks, which contains all of the internal DECT protocol
control, but may also include some external user information.
NOTE 3: The C-plane stack always contains protocol entities up to and including the network
layer.
call: All of the Network (NWK) layer processes involved in one network layer peer-to-peer association.
NOTE 4: Call may sometimes be used to refer to processes of all layers, since lower layer
processes are implicitly required.
Cordless Terminal Adapter (CTA): Physical grouping that contains a DECT portable termination and a
line interface.
Fixed Part (DECT Fixed Part) (FP): A physical grouping that contains all of the elements in the DECT
network between the local network and the DECT air interface.
NOTE 5: A DECT FP contains the logical elements of at least one FT, plus additional
implementation specific elements.
DECT network: A network that uses the DECT air interface to interconnect a local network to one or
more portable applications. The logical boundaries of the DECT network are defined to be at the top of the
DECT network layer.
NOTE 6: A DECT Network is a logical grouping that contains one or more fixed radio
terminations plus their associated portable radio termination. The boundaries of the
DECT network are not physical boundaries.
DECT intermediate fixed system: A logical grouping that contains all the functions between the DECT DI
reference point and the reference point on the fixed side of the DECT air interface.
NOTE 7: The DECT Intermediate Fixed System (DIFS) = FT + (local network up to the fixed
side ISDN reference point (including fixed side Interworking Unit (IWU))), see
ETR 056 [14].
DECT intermediate portable system: A logical grouping that contains all the functions between the
DECT DI reference point and the ISDN S reference point on the portable side of the DECT air interface.
---------------------- Page: 11 ----------------------
SIST ETS 300 765-2:1999
Page 10
ETS 300 765-2: April 1998
NOTE 8: The DECT Intermediate Portable System (DIPS) = Portable radio Termination (PT) +
(Portable Application (PA) up to the portable side ISDN S reference point (including
portable side IWU)), see ETR 056 [14].
Fixed Radio Termination (FT): A logical group of functions that contains all of the DECT processes and
procedures on the fixed side of the DECT air interface.
NOTE 9: A FT only includes elements that are defined in the DECT Common Interface (CI)
standard. This includes radio transmission elements together with a selection of layer
2 and layer 3 elements.
handover: The process of switching a call in progress from one physical channel to another physical
channel.
NOTE 10: There are two physical forms of handover, intra-cell handover and inter-cell handover.
incoming call: A call received at a CTA.
inter-cell handover: The switching of a call in progress from one cell to another cell.
internal handover: Handover processes that are completely internal to one FT. Internal handover
reconnects the call at the lower layers, while maintaining the call at the NWK layer.
NOTE 11: The lower layer reconnection can either be at the Data Link Control (DLC) layer
(connection handover) or at the MAC layer (bearer handover).
interoperability: The capability of FPs and CTAs, that enable a CTA to obtain access to teleservices in
more than one location area and/or from more than one operator (more than one service provider).
Interworking Unit (IWU): A unit that is used to interconnect subnetworks.
NOTE 12: The IWU will contain the interworking functions necessary to support the required
subnetwork interworking.
intra-cell handover: The switching of a call in progress from one physical channel of one cell to another
physical channel of the same cell.
Local Network (LNW): A telecommunication network capable of offering local telecommunication
services.
NOTE 13: The term does not include legal or regulatory aspects, nor does it indicate if the
network is a public network or a private network.
location area: The domain in which a CTA may receive (and/or make) calls as a result of a single
location registration.
location registration: The process whereby the position of a DECT PT is determined to the level of one
location area, and this position is updated in one or more databases.
NOTE 14: These databases are not included within a DECT FT.
MAC Connection (CONNECTION): An association between one source MAC Multi-Bearer Control
(MBC) entity and one destination MAC MBC entity. This provides a set of related MAC services (a set of
logical channels), and it can involve one or more underlying MAC bearers.
mobility class 1: Local area applications, for which terminals are pre-registered off-air with one or more
specific fixed parts, and establishment of service and user parameters is therefore implicit, according to a
profile-defined list.
mobility class 2: Private and Public roaming applications for which terminals may move between fixed
parts within a given domain and for which association of service parameters is explicit at the time of
service request.
---------------------- Page: 12 ----------------------
SIST ETS 300 765-2:1999
Page 11
ETS 300 765-2: April 1998
outgoing call: A call originating from a CTA.
Portable Application (PA): A logical grouping that contains all the elements that lie beyond the DECT
network boundary on the portable side.
NOTE 15: The functions contained in the PA may be physically distributed, but any such
distribution is invisible to the DECT network.
Portable Part (DECT Portable Part) (PP): A physical grouping that contains all elements between the
user and the DECT air interface. PP is a generic term that may describe one or several physical pieces.
NOTE 16: A DECT PP is logically divided into one PT plus one or more PAs.
Portable radio Termination (PT): A logical group of functions that contains all of the DECT processes
and procedures on the portable side of the DECT air interface.
NOTE 17: A PT only includes elements that are defined in the DECT CI standard. This includes
radio transmission elements (layer 1) together with a selection of layer 2 and layer 3
elements.
Radio Fixed Part (RFP): One physical sub-group of a FP that contains all the radio end points (one or
more) that are connected to a single system of antennas.
registration: An ambiguous term, that should always be qualified. See either location registration or
subscription registration.
service type A: Low speed frame relay, with a net sustainable throughput of up to 24 kbits/s, optimized
for bursty data, low power consumption and low complexity applications such as hand-portable
equipment.
service type B: High performance frame relay, with a net sustainable throughput of up to 552 kbits/s,
optimized for high speed and low latency with bursty data. Equipment implementation the Type B profile
shall inter-operate with Type A equipment.
service type C: Non-transparent connection of data streams requiring Link Access Protocol (LAP)
services,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.