oSIST prEN 302 217-2 V3.3.0:2021
(Main)Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to 86 GHz - Harmonised Standard for access to radio spectrum
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to 86 GHz - Harmonised Standard for access to radio spectrum
REN/ATTM-0450
Fiksni radijski sistemi - Karakteristike in zahteve za opremo tipa točka-točka in antene - 2. del: Digitalni sistemi, ki delujejo v frekvenčnih pasovih od 1 GHz do 86 GHz - Harmonizirani standard za dostop do radijskega spektra
General Information
Buy Standard
Standards Content (sample)
Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
HARMONISED EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2: Digital systems operating in frequency bands
from 1 GHz to 86 GHz;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
Reference
REN/ATTM-0450
Keywords
antenna, DFRS, digital, DRRS, FWA,
point-to-point, radio, regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspxIf you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspxNotice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
Contents
Intellectual Property Rights ................................................................................................................................ 9
Foreword ............................................................................................................................................................. 9
Modal verbs terminology .................................................................................................................................. 10
Introduction ...................................................................................................................................................... 10
1 Scope ...................................................................................................................................................... 11
2 References .............................................................................................................................................. 11
2.1 Normative references ....................................................................................................................................... 11
2.2 Informative references ...................................................................................................................................... 12
3 Definition of terms, symbols and abbreviations ..................................................................................... 15
3.1 Terms ................................................................................................................................................................ 15
3.2 Symbols ............................................................................................................................................................ 15
3.3 Abbreviations ................................................................................................................................................... 15
4 Technical requirements specifications ................................................................................................... 15
4.0 Generality ......................................................................................................................................................... 15
4.0.1 The "Manufacturer declarations" concept ................................................................................................... 15
4.0.2 Basic understanding of all requirements ..................................................................................................... 16
4.1 Framework for categorization of system .......................................................................................................... 17
4.1.1 Introduction and equipment flexibility ....................................................................................................... 17
4.1.2 Operating frequency bands and channel arrangements ............................................................................... 18
4.1.3 Spectral efficiency classes .......................................................................................................................... 18
4.1.4 System alternatives ..................................................................................................................................... 19
4.1.5 Channel arrangements and utilization ......................................................................................................... 19
4.1.6 Specific requirements for frequency bands ................................................................................................. 20
4.1.7 Minimum RIC density for spectral efficiency class selection ..................................................................... 21
4.1.8 System identification and traffic loading .................................................................................................... 22
4.1.9 Environmental profile ................................................................................................................................. 23
4.2 Transmitter requirements ................................................................................................................................. 23
4.2.0 General: system loading .............................................................................................................................. 23
4.2.1 Transmitter power and power environmental variation .............................................................................. 24
4.2.1.1 Transmitter maximum power and EIRP ................................................................................................ 24
4.2.1.2 Transmitter combined nominal output power and EIRP limits ............................................................. 24
4.2.1.3 Transmitter output power environmental variation ............................................................................... 25
4.2.2 Transmitter power and frequency control ................................................................................................... 25
4.2.2.1 Transmitter Power and Frequency Control (ATPC, RTPC and RFC) .................................................. 25
4.2.2.1.0 General background ......................................................................................................................... 25
4.2.2.1.1 Automatic Transmit Power Control (ATPC) ................................................................................... 25
4.2.2.1.2 Remote Transmit Power Control (RTPC) ....................................................................................... 25
4.2.2.1.3 Transmitter Remote Frequency Control (RFC) ............................................................................... 26
4.2.3 Transmitter Radio Frequency (RF) spectrum mask .................................................................................... 26
4.2.3.1 Limits background ................................................................................................................................ 26
4.2.3.2 Limits .................................................................................................................................................... 29
4.2.4 Transmitter discrete CW components exceeding the transmitter Radio Frequency spectrum mask
limit ............................................................................................................................................................. 43
4.2.4.1 Transmitter discrete CW components at the symbol rate ...................................................................... 43
4.2.4.2 Transmitter other discrete CW components exceeding the transmitter Radio Frequency spectrum
mask limit .............................................................................................................................................. 43
4.2.5 Transmitter unwanted emissions in the spurious domain ........................................................................... 45
4.2.6 Transmitter dynamic Change of Modulation Order .................................................................................... 46
4.2.7 Transmitter Frequency tolerance ................................................................................................................ 47
4.2.8 Transmitter emission limitations outside the allocated band ...................................................................... 47
4.3 Receiver requirements ...................................................................................................................................... 47
4.3.0 General: System loading ............................................................................................................................. 47
4.3.1 Receiver unwanted emissions in the spurious domain................................................................................ 47
4.3.2 BER as a function of receiver input signal level RSL ................................................................................ 48
ETSI---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
4.3.3 Receiver selectivity ..................................................................................................................................... 48
4.3.3.1 Introduction ........................................................................................................................................... 48
4.3.3.2 Receiver co-channel, first and second adjacent channel interference sensitivity .................................. 49
4.3.3.2.1 Requirements basic .......................................................................................................................... 49
4.3.3.2.2 Limits for co-channel and first adjacent channel interference sensitivity ........................................ 49
4.3.3.2.3 Limits for second adjacent channel interference sensitivity ............................................................ 50
4.3.3.3 Receiver Blocking (CW spurious interference sensitivity) ................................................................... 50
4.4 Antenna Characteristics .................................................................................................................................... 51
4.4.1 Integral antennas or dedicated antennas...................................................................................................... 51
4.4.1.1 Introduction ........................................................................................................................................... 51
4.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) ............................................................................ 51
4.4.1.3 Antenna gain ......................................................................................................................................... 51
4.4.1.4 Antenna Cross-Polar Discrimination (XPD) ......................................................................................... 51
4.4.2 Guidelines for stand-alone antennas ........................................................................................................... 52
5 Testing for compliance with technical requirements .............................................................................. 52
5.1 Environmental and other conditions for testing ................................................................................................ 52
5.1.1 Environmental conditions ........................................................................................................................... 52
5.1.1.1 Generality .............................................................................................................................................. 52
5.1.1.2 Minimum profile for equipment indoor use .......................................................................................... 52
5.1.1.3 Minimum profile for equipment outdoor use ........................................................................................ 52
5.1.2 Other basic conditions ................................................................................................................................ 52
5.2 Test methods for the transmitter ....................................................................................................................... 53
5.2.0 General test summary ................................................................................................................................. 53
5.2.1 Transmitter power and power environmental variation .............................................................................. 55
5.2.1.1 Transmitter maximum power and EIRP ................................................................................................ 55
5.2.1.2 Transmitter combined nominal output power and EIRP limits ............................................................. 55
5.2.1.3 Transmitter output power environmental variation ............................................................................... 55
5.2.2 Transmitter power and frequency control ................................................................................................... 55
5.2.2.1 Transmitter Power and Frequency Control (ATPC, RTPC and RFC) .................................................. 55
5.2.2.1.1 Automatic Transmit Power Control (ATPC) ................................................................................... 55
5.2.2.1.2 Remote Transmit Power Control (RTPC) ....................................................................................... 56
5.2.2.1.3 Transmitter Remote Frequency Control (RFC) ............................................................................... 56
5.2.3 Transmitter Radio Frequency spectrum mask............................................................................................. 56
5.2.4 Transmitter discrete CW components exceeding the transmitter Radio Frequency spectrum mask
limit ............................................................................................................................................................. 57
5.2.5 Transmitter unwanted emissions in the spurious domain ........................................................................... 57
5.2.6 Transmitter dynamic Change of Modulation Order .................................................................................... 57
5.2.7 Transmitter Radio Frequency tolerance ...................................................................................................... 57
5.2.8 Transmitter emission limitations outside the allocated band ...................................................................... 58
5.3 Test methods for the receiver ........................................................................................................................... 58
5.3.0 General test summary ................................................................................................................................. 58
5.3.1 Receiver unwanted emissions in the spurious domain ................................................................................ 59
5.3.2 BER as a function of Receiver input Signal Level (RSL)........................................................................... 59
5.3.3 Receiver selectivity ..................................................................................................................................... 60
5.3.3.1 Void....................................................................................................................................................... 60
5.3.3.2 Receiver co-channel, first and second adjacent channel interference sensitivity .................................. 60
5.3.3.2.1 Void ................................................................................................................................................. 60
5.3.3.2.2 Receiver co-channel and first adjacent channel ............................................................................... 60
5.3.3.2.3 Receiver second adjacent channel ................................................................................................... 60
5.3.3.3 Receiver Blocking (CW spurious interference sensitivity) ................................................................... 60
5.4 Antenna test methods ....................................................................................................................................... 61
5.4.1 Integral antennas or dedicated antenna ....................................................................................................... 61
5.4.1.1 Summary ............................................................................................................................................... 61
5.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) ............................................................................ 61
5.4.1.3 Antenna gain ......................................................................................................................................... 61
5.4.1.4 Antenna Cross-Polar Discrimination (XPD) ......................................................................................... 61
5.4.2 Information on stand-alone antennas tests .................................................................................................. 61
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU ......................................................... 62
ETSI---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
Annex B (normative): Frequency bands from 1,4 GHz to 2,6 GHz ................................................ 64
B.1 Introduction ............................................................................................................................................ 64
B.2 General characteristics ........................................................................................................................... 64
B.2.1 Frequency characteristics and channel arrangements ....................................................................................... 64
B.2.2 Transmission capacities .................................................................................................................................... 65
B.3 Transmitter ............................................................................................................................................. 66
B.3.1 General requirements ....................................................................................................................................... 66
B.3.2 Transmitter Radio Frequency spectrum masks options .................................................................................... 66
B.4 Receiver .................................................................................................................................................. 67
B.4.1 General requirements ....................................................................................................................................... 67
B.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 67
B.4.3 Receiver co-channel, first and second adjacent channels interference sensitivity ............................................ 68
Annex C (normative): Frequency bands from 3,5 GHz to 11 GHz (channel separation up to
30 MHz, 56/60 MHz and 112 MHz) .............................................................. 69
C.1 Introduction ............................................................................................................................................ 69
C.2 General characteristics ........................................................................................................................... 69
C.2.1 Frequency characteristics and channel arrangements ....................................................................................... 69
C.2.2 Transmission capacities .................................................................................................................................... 71
C.3 Transmitter ............................................................................................................................................. 71
C.3.1 General requirements ....................................................................................................................................... 71
C.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 71
C.4 Receiver .................................................................................................................................................. 72
C.4.1 General requirements ....................................................................................................................................... 72
C.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 72
C.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 74
Annex D (normative): Frequency bands from 4 GHz to 11 GHz (channel separation 40 MHz
and 80 MHz) ................................................................................................... 76
D.1 Introduction ............................................................................................................................................ 76
D.2 General characteristics ........................................................................................................................... 76
D.2.1 Frequency characteristics and channel arrangements ....................................................................................... 76
D.2.2 Transmission capacities .................................................................................................................................... 77
D.3 Transmitter ............................................................................................................................................. 78
D.3.1 General requirements ....................................................................................................................................... 78
D.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 78
D.4 Receiver .................................................................................................................................................. 78
D.4.1 General requirements ....................................................................................................................................... 78
D.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 78
D.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 80
Annex E (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz .......................................... 81
E.1 Introduction ............................................................................................................................................ 81
E.2 General characteristics ........................................................................................................................... 81
E.2.1 Frequency characteristics and channel arrangements ....................................................................................... 81
E.2.2 Transmission capacities .................................................................................................................................... 82
E.3 Transmitter ............................................................................................................................................. 82
E.3.1 General requirements ....................................................................................................................................... 82
E.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 83
E.4 Receiver .................................................................................................................................................. 83
E.4.1 General requirements ....................................................................................................................................... 83
E.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 83
ETSI---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
E.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 86
Annex F (normative): Frequency bands from 23 GHz to 42 GHz .................................................. 87
F.1 Introduction ............................................................................................................................................ 87
F.2 General characteristics ........................................................................................................................... 87
F.2.1 Frequency characteristics and channel arrangements ....................................................................................... 87
F.2.2 Transmission capacities .................................................................................................................................... 88
F.3 Transmitter ............................................................................................................................................. 88
F.3.1 General requirements ....................................................................................................................................... 88
F.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 89
F.4 Receiver .................................................................................................................................................. 89
F.4.1 General requirements ....................................................................................................................................... 89
F.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 89
F.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 92
Annex G (normative): Frequency bands from 50 GHz to 55 GHz .................................................. 93
G.1 Introduction...
SLOVENSKI STANDARD
oSIST prEN 302 217-2 V3.3.0:2021
01-julij-2021
Fiksni radijski sistemi - Karakteristike in zahteve za opremo tipa točka-točka in
antene - 2. del: Digitalni sistemi, ki delujejo v frekvenčnih pasovih od 1 GHz do 86
GHz - Harmonizirani standard za dostop do radijskega spektraFixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to 86
GHz - Harmonised Standard for access to radio spectrumTa slovenski standard je istoveten z: ETSI EN 302 217-2 V3.3.0 (2021-06)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
oSIST prEN 302 217-2 V3.3.0:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN 302 217-2 V3.3.0:2021
---------------------- Page: 2 ----------------------
oSIST prEN 302 217-2 V3.3.0:2021
Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
HARMONISED EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2: Digital systems operating in frequency bands
from 1 GHz to 86 GHz;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
oSIST prEN 302 217-2 V3.3.0:2021
2 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
Reference
REN/ATTM-0450
Keywords
antenna, DFRS, digital, DRRS, FWA,
point-to-point, radio, regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspxIf you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspxNotice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 302 217-2 V3.3.0:2021
3 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
Contents
Intellectual Property Rights ................................................................................................................................ 9
Foreword ............................................................................................................................................................. 9
Modal verbs terminology .................................................................................................................................. 10
Introduction ...................................................................................................................................................... 10
1 Scope ...................................................................................................................................................... 11
2 References .............................................................................................................................................. 11
2.1 Normative references ....................................................................................................................................... 11
2.2 Informative references ...................................................................................................................................... 12
3 Definition of terms, symbols and abbreviations ..................................................................................... 15
3.1 Terms ................................................................................................................................................................ 15
3.2 Symbols ............................................................................................................................................................ 15
3.3 Abbreviations ................................................................................................................................................... 15
4 Technical requirements specifications ................................................................................................... 15
4.0 Generality ......................................................................................................................................................... 15
4.0.1 The "Manufacturer declarations" concept ................................................................................................... 15
4.0.2 Basic understanding of all requirements ..................................................................................................... 16
4.1 Framework for categorization of system .......................................................................................................... 17
4.1.1 Introduction and equipment flexibility ....................................................................................................... 17
4.1.2 Operating frequency bands and channel arrangements ............................................................................... 18
4.1.3 Spectral efficiency classes .......................................................................................................................... 18
4.1.4 System alternatives ..................................................................................................................................... 19
4.1.5 Channel arrangements and utilization ......................................................................................................... 19
4.1.6 Specific requirements for frequency bands ................................................................................................. 20
4.1.7 Minimum RIC density for spectral efficiency class selection ..................................................................... 21
4.1.8 System identification and traffic loading .................................................................................................... 22
4.1.9 Environmental profile ................................................................................................................................. 23
4.2 Transmitter requirements ................................................................................................................................. 23
4.2.0 General: system loading .............................................................................................................................. 23
4.2.1 Transmitter power and power environmental variation .............................................................................. 24
4.2.1.1 Transmitter maximum power and EIRP ................................................................................................ 24
4.2.1.2 Transmitter combined nominal output power and EIRP limits ............................................................. 24
4.2.1.3 Transmitter output power environmental variation ............................................................................... 25
4.2.2 Transmitter power and frequency control ................................................................................................... 25
4.2.2.1 Transmitter Power and Frequency Control (ATPC, RTPC and RFC) .................................................. 25
4.2.2.1.0 General background ......................................................................................................................... 25
4.2.2.1.1 Automatic Transmit Power Control (ATPC) ................................................................................... 25
4.2.2.1.2 Remote Transmit Power Control (RTPC) ....................................................................................... 25
4.2.2.1.3 Transmitter Remote Frequency Control (RFC) ............................................................................... 26
4.2.3 Transmitter Radio Frequency (RF) spectrum mask .................................................................................... 26
4.2.3.1 Limits background ................................................................................................................................ 26
4.2.3.2 Limits .................................................................................................................................................... 29
4.2.4 Transmitter discrete CW components exceeding the transmitter Radio Frequency spectrum mask
limit ............................................................................................................................................................. 43
4.2.4.1 Transmitter discrete CW components at the symbol rate ...................................................................... 43
4.2.4.2 Transmitter other discrete CW components exceeding the transmitter Radio Frequency spectrum
mask limit .............................................................................................................................................. 43
4.2.5 Transmitter unwanted emissions in the spurious domain ........................................................................... 45
4.2.6 Transmitter dynamic Change of Modulation Order .................................................................................... 46
4.2.7 Transmitter Frequency tolerance ................................................................................................................ 47
4.2.8 Transmitter emission limitations outside the allocated band ...................................................................... 47
4.3 Receiver requirements ...................................................................................................................................... 47
4.3.0 General: System loading ............................................................................................................................. 47
4.3.1 Receiver unwanted emissions in the spurious domain................................................................................ 47
4.3.2 BER as a function of receiver input signal level RSL ................................................................................ 48
ETSI---------------------- Page: 5 ----------------------
oSIST prEN 302 217-2 V3.3.0:2021
4 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
4.3.3 Receiver selectivity ..................................................................................................................................... 48
4.3.3.1 Introduction ........................................................................................................................................... 48
4.3.3.2 Receiver co-channel, first and second adjacent channel interference sensitivity .................................. 49
4.3.3.2.1 Requirements basic .......................................................................................................................... 49
4.3.3.2.2 Limits for co-channel and first adjacent channel interference sensitivity ........................................ 49
4.3.3.2.3 Limits for second adjacent channel interference sensitivity ............................................................ 50
4.3.3.3 Receiver Blocking (CW spurious interference sensitivity) ................................................................... 50
4.4 Antenna Characteristics .................................................................................................................................... 51
4.4.1 Integral antennas or dedicated antennas...................................................................................................... 51
4.4.1.1 Introduction ........................................................................................................................................... 51
4.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) ............................................................................ 51
4.4.1.3 Antenna gain ......................................................................................................................................... 51
4.4.1.4 Antenna Cross-Polar Discrimination (XPD) ......................................................................................... 51
4.4.2 Guidelines for stand-alone antennas ........................................................................................................... 52
5 Testing for compliance with technical requirements .............................................................................. 52
5.1 Environmental and other conditions for testing ................................................................................................ 52
5.1.1 Environmental conditions ........................................................................................................................... 52
5.1.1.1 Generality .............................................................................................................................................. 52
5.1.1.2 Minimum profile for equipment indoor use .......................................................................................... 52
5.1.1.3 Minimum profile for equipment outdoor use ........................................................................................ 52
5.1.2 Other basic conditions ................................................................................................................................ 52
5.2 Test methods for the transmitter ....................................................................................................................... 53
5.2.0 General test summary ................................................................................................................................. 53
5.2.1 Transmitter power and power environmental variation .............................................................................. 55
5.2.1.1 Transmitter maximum power and EIRP ................................................................................................ 55
5.2.1.2 Transmitter combined nominal output power and EIRP limits ............................................................. 55
5.2.1.3 Transmitter output power environmental variation ............................................................................... 55
5.2.2 Transmitter power and frequency control ................................................................................................... 55
5.2.2.1 Transmitter Power and Frequency Control (ATPC, RTPC and RFC) .................................................. 55
5.2.2.1.1 Automatic Transmit Power Control (ATPC) ................................................................................... 55
5.2.2.1.2 Remote Transmit Power Control (RTPC) ....................................................................................... 56
5.2.2.1.3 Transmitter Remote Frequency Control (RFC) ............................................................................... 56
5.2.3 Transmitter Radio Frequency spectrum mask............................................................................................. 56
5.2.4 Transmitter discrete CW components exceeding the transmitter Radio Frequency spectrum mask
limit ............................................................................................................................................................. 57
5.2.5 Transmitter unwanted emissions in the spurious domain ........................................................................... 57
5.2.6 Transmitter dynamic Change of Modulation Order .................................................................................... 57
5.2.7 Transmitter Radio Frequency tolerance ...................................................................................................... 57
5.2.8 Transmitter emission limitations outside the allocated band ...................................................................... 58
5.3 Test methods for the receiver ........................................................................................................................... 58
5.3.0 General test summary ................................................................................................................................. 58
5.3.1 Receiver unwanted emissions in the spurious domain ................................................................................ 59
5.3.2 BER as a function of Receiver input Signal Level (RSL)........................................................................... 59
5.3.3 Receiver selectivity ..................................................................................................................................... 60
5.3.3.1 Void....................................................................................................................................................... 60
5.3.3.2 Receiver co-channel, first and second adjacent channel interference sensitivity .................................. 60
5.3.3.2.1 Void ................................................................................................................................................. 60
5.3.3.2.2 Receiver co-channel and first adjacent channel ............................................................................... 60
5.3.3.2.3 Receiver second adjacent channel ................................................................................................... 60
5.3.3.3 Receiver Blocking (CW spurious interference sensitivity) ................................................................... 60
5.4 Antenna test methods ....................................................................................................................................... 61
5.4.1 Integral antennas or dedicated antenna ....................................................................................................... 61
5.4.1.1 Summary ............................................................................................................................................... 61
5.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) ............................................................................ 61
5.4.1.3 Antenna gain ......................................................................................................................................... 61
5.4.1.4 Antenna Cross-Polar Discrimination (XPD) ......................................................................................... 61
5.4.2 Information on stand-alone antennas tests .................................................................................................. 61
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU ......................................................... 62
ETSI---------------------- Page: 6 ----------------------
oSIST prEN 302 217-2 V3.3.0:2021
5 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
Annex B (normative): Frequency bands from 1,4 GHz to 2,6 GHz ................................................ 64
B.1 Introduction ............................................................................................................................................ 64
B.2 General characteristics ........................................................................................................................... 64
B.2.1 Frequency characteristics and channel arrangements ....................................................................................... 64
B.2.2 Transmission capacities .................................................................................................................................... 65
B.3 Transmitter ............................................................................................................................................. 66
B.3.1 General requirements ....................................................................................................................................... 66
B.3.2 Transmitter Radio Frequency spectrum masks options .................................................................................... 66
B.4 Receiver .................................................................................................................................................. 67
B.4.1 General requirements ....................................................................................................................................... 67
B.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 67
B.4.3 Receiver co-channel, first and second adjacent channels interference sensitivity ............................................ 68
Annex C (normative): Frequency bands from 3,5 GHz to 11 GHz (channel separation up to
30 MHz, 56/60 MHz and 112 MHz) .............................................................. 69
C.1 Introduction ............................................................................................................................................ 69
C.2 General characteristics ........................................................................................................................... 69
C.2.1 Frequency characteristics and channel arrangements ....................................................................................... 69
C.2.2 Transmission capacities .................................................................................................................................... 71
C.3 Transmitter ............................................................................................................................................. 71
C.3.1 General requirements ....................................................................................................................................... 71
C.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 71
C.4 Receiver .................................................................................................................................................. 72
C.4.1 General requirements ....................................................................................................................................... 72
C.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 72
C.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 74
Annex D (normative): Frequency bands from 4 GHz to 11 GHz (channel separation 40 MHz
and 80 MHz) ................................................................................................... 76
D.1 Introduction ............................................................................................................................................ 76
D.2 General characteristics ........................................................................................................................... 76
D.2.1 Frequency characteristics and channel arrangements ....................................................................................... 76
D.2.2 Transmission capacities .................................................................................................................................... 77
D.3 Transmitter ............................................................................................................................................. 78
D.3.1 General requirements ....................................................................................................................................... 78
D.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 78
D.4 Receiver .................................................................................................................................................. 78
D.4.1 General requirements ....................................................................................................................................... 78
D.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 78
D.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 80
Annex E (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz .......................................... 81
E.1 Introduction ............................................................................................................................................ 81
E.2 General characteristics ........................................................................................................................... 81
E.2.1 Frequency characteristics and channel arrangements ....................................................................................... 81
E.2.2 Transmission capacities .................................................................................................................................... 82
E.3 Transmitter ............................................................................................................................................. 82
E.3.1 General requirements ....................................................................................................................................... 82
E.3.2 Transmitter Radio Frequency spectrum masks................................................................................................. 83
E.4 Receiver .................................................................................................................................................. 83
E.4.1 General requirements ....................................................................................................................................... 83
E.4.2 BER as a function of Receiver input Signal Level (RSL) ................................................................................ 83
ETSI---------------------- Page: 7 ----------------------
oSIST prEN 302 217-2 V3.3.0:2021
6 Draft ETSI EN 302 217-2 V3.3.0 (2021-06)
E.4.3 Receiver co-channel and first adjacent channel interference sensitivity .......................................................... 86
Annex F (normative): Frequency bands from 23 GHz to 42 GHz .................................................. 87
F.1 Introduction ............................................................................................................................................ 87
F.2 General characteristics ........................................................................................................................... 87
F.2.1 Frequency characteristics and channel arrangements ....................................................................................... 87
F.2.2 Transmission capacities ....................................................................................................................
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.