SIST EN 302 217-1 V2.1.1:2013
(Main)Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 1: Overview and system-independent common characteristics
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 1: Overview and system-independent common characteristics
The present document applies to the following digital fixed radio systems (DFRS), including equipment with integral antenna and antenna types:
-point-to-point systems intended for operation in frequency bands that require co-ordination;
-point-to-point systems intended for operation in frequency bands that do not require co-ordination;
-antennas for point-to-point operation.
The present document summarizes all characteristics, principles, terms and definitions that are common to all P-P equipment and antennas and its consultation is necessary when using all other parts of EN 302 217 series.
EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36] summarize the other system dependent characteristics and include limits for "non-essential" requirements, EN 302 217-2-2 [i.34], EN 302 217-3 [i.35] and EN 302 217-4-2 [i.37] contain the whole description and limits of "essential" requirements under article 3.2 of the R&TTE Directive [1]. Health and safety requirements, relevant to article 3.1a of the R&TTE Directive [1] are not considered in any part of this EN 302 217 series. CENELEC is responsible for the relevant standards. EMC conditions and requirements, relevant to article 3.1b of the R&TTE Directive [1] and any other essential requirement relevant to article 3.3 of the R&TTE Directive [1] are not in the scope of any part of this EN 302 217 series. They may be found in EN 301 489-1 [i.26] and EN 301 489-4 [i.27]. NOTE: A list of such harmonised ENs is available on the web site http://www.newapproach.org. For administration's guidance when notifying their regulated interfaces in accordance with article 4.1 of the R&TTE Directive [1], annex B provides explanatory considerations on the applicability of the TCAM-RIG format for P-P fixed links. An example of such a notification is also provided. Annex B has been elaborated in co-ordination with the CEPT ECC WGSE.
Fiksni radijski sistemi - Karakteristike in zahteve za opremo in antene tipa točka-točka - 1. del: Pregled in sistemsko neodvisne splošne karakteristike
Ta dokument velja za naslednje digitalne fiksne radijske sisteme (DFRS), vključno z opremo z vgrajeno anteno in vrstami anten:
– sistemi tipa točka-točka, namenjeni za delovanje znotraj frekvenčnih pasov, ki zahtevajo usklajevanje;
– sistemi tipa točka-točka, namenjeni za delovanje znotraj frekvenčnih pasov, ki ne zahtevajo usklajevanja;
– antene za delovanje tipa točka-točka.
Ta dokument povzema vse lastnosti, načela, določila in definicije, ki so skupne za vse dele opreme in antene v sistemih tipa točka-točka in jih je treba upoštevati pri uporabi vseh ostalih delov skupine EN 302 217.
Standarda EN 302 217-2-1 [i.33] in EN 302 217-4-1 [i.36] povzemata druge sistemsko odvisne lastnosti in vključujeta omejitve za »nebistvene« zahteve. Standardi EN 302 217-2-2 [i.34], EN 302 217-3 [i.35] in EN 302 217-4-2 [i.37] vsebujejo celoten opis in omejitve »bistvenih« zahtev v členu 3.2 direktive R&TTE [1]. Zdravstvene in varnostne zahteve v zvezi s členom 3.1a direktive R&TTE [1] niso obravnavane v nobenem delu te skupine EN 302 217. CENELEC je odgovoren za ustrezne standarde. Pogoji in zahteve glede elektromagnetne združljivosti (EMC) v zvezi s členom 3.1b direktive R&TTE [1] ter morebitne druge bistvene zahteve v zvezi s členom 3.3 direktive R&TTE [1] niso obravnavani v nobenem delu te skupine EN 302 217. Navedeni so v EN 301 489-1 [i.26] in EN 301 489-4 [i.27]. OPOMBA: Seznam tovrstnih usklajenih standardov EN je na voljo na spletnem mestu http://www.newapproach.org. Dodatek B navaja razlage glede uporabnosti oblike TCAM-RIG za fiksne povezave tipa točka-točka za namene podajanja navodil za upravljanje pri obveščanju njihovih reguliranih vmesnikov v skladu s členom 4.1 direktive R&TTE [1]. Na voljo je tudi primer tovrstnega obvestila. Dodatek B je bil pripravljen v sodelovanju z CEPT ECC WGSE.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WLNHFixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 1: Overview and system-independent common characteristics33.120.40AnteneAerials33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 302 217-1 Version 2.1.1SIST EN 302 217-1 V2.1.1:2013en01-oktober-2013SIST EN 302 217-1 V2.1.1:2013SLOVENSKI
STANDARD
SIST EN 302 217-1 V2.1.1:2013
ETSI EN 302 217-1 V2.1.1 (2013-07) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview and system-independent common characteristics
European Standard SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 2
Reference REN/ATTM-04016 Keywords antenna, DFRS, digital, DRRS, FWA, point-to-point, radio, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 3 Contents Intellectual Property Rights . 4 Foreword . 4 Introduction . 5 1 Scope . 12 2 References . 12 2.1 Normative references . 12 2.2 Informative references . 15 3 Definitions, symbols and abbreviations . 17 3.1 Definitions . 17 3.2 Symbols . 22 3.3 Abbreviations . 23 4 General characteristics . 26 4.1 Performance and availability requirements . 26 4.2 Environmental profiles . 26 4.2.1 Environmental profile declared under the R&TTE Directive . 26 4.2.2 ETSI environmental profiles . 26 4.2.2.1 Equipment within weather-protected locations (indoor locations) . 27 4.2.2.2 Equipment for not-weather-protected locations (outdoor locations) . 27 4.2.3 Test environment profiles . 27 4.3 Power supply . 27 4.3.1 Power supply profile declared under the R&TTE Directive . 27 4.3.2 ETSI power supply profile . 28 4.4 System block diagram . 28 5 Baseband interfaces and parameters . 28 5.1 Plesiochronous interfaces . 29 5.2 ISDN interfaces . 29 5.3 Synchronous digital hierarchy interfaces . 29 5.4 Other baseband data interfaces . 29 Annex A (informative): Miscellaneous characteristics . 30 A.1 Telecommunications Management Network (TMN) interface . 30 A.2 Mechanical characteristics . 30 Annex B (informative): Notification of interfaces under article 4.1 of the R&TTE Directive . 31 B.1 Applicability of TCAM-RIG format of radio interface specifications to Fixed Services . 31 B.2 Proposed list of radio interface specifications for Fixed Services . 32 Annex C (informative): Cross references to previously relevant ENs and TSs . 33 History . 36
SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas, as identified below: Part 1: "Overview and system-independent common characteristics"; Part 2-1: "System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 2-2: "Digital systems operating in frequency bands where frequency co-ordination is applied; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 3: "Equipment operating in frequency bands where both frequency coordinated or uncoordinated deployment might be applied; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE"; Part 4-1: "System-dependent requirements for antennas"; Part 4-2: "Antennas; Harmonized EN covering the essential requirements of article 3.2 of R&TTE Directive".
National transposition dates Date of adoption of this EN: 25 June 2013 Date of latest announcement of this EN (doa): 30 September 2013 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2014 Date of withdrawal of any conflicting National Standard (dow): 31 March 2014
Major variants with respect to previous published version • System options identification has been changed, in line with corresponding changes in Parts 2-1 [i.33] and 2-2 [i.34] of EN 302 217. Old systems notations (A.1, … B.1, … C.1, … D.1, … E.1 ….) have been removed and the system capacity is defined in term of minimum Radio Interface Capacity (RIC) rather than previous hierarchic PDH/SDH interfaces. Each equipment in the scope of the present document refers to a coherent set of transmitter and receiver requirements uniquely defined on the basis of the following identifying parameters: 1) operating frequency band; 2) operating radio frequency channel separation; SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 5 3) spectral efficiency class, to which the minimum RIC density is associated. • Cross reference to older "historical" source ENs, no longer of interest has been moved to an annex. • Required new and updated "definitions". • Alignment of frequency bands and equipment options introduced in other parts of EN 302 217 series. Introduction (i) Generality and historical background Digital Fixed Radio Systems (DFRS), used in European countries, had been historically specified in a relatively large number of specific European Norms produced by ETSI. Those previous documents, already superseded by first version of this EN 302 217 series, contained both essential requirements and other requirements that, even if not considered essential under the Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (hereafter mentioned as the R&TTE Directive) [1], may be applicable. Standards for point-to-point systems, including antennas, cover a very large range of traffic capacities, channel separations (CS), modulation formats and applications over a very wide range of frequency bands that are summarized in table 1. Table 1: Digital Fixed Radio Systems (DFRS) parameters Parameter Range Frequency bands from 1 GHz to 86 GHz Traffic capacities from 9,6 kbit/s to 622 Mbit/s and to Gigabit/s and above in the highest bands Channel separations from 25 kHz to 112 MHz and to Gigahertz and above in the highest bands Modulation formats from 2 to 2 048 states (amplitude and/or phase and/or frequency modulated states) Typical applications POINT-TO-POINT (P-P) CONNECTIONS: rural and urban low/medium/high capacity links for mobile infrastructure, transport/trunk (long haul), FWA/BWA/MWA backhaul, access, governmental (non-military) links, private fixed networks, SAP/SAB P to P audio and video links STAND ALONE ANTENNAS: for all of the above applications when integral antennas are not employed
The regulatory framework for placing radio systems on the market, established by the R&TTE Directive [1] also requires the availability of Harmonized ENs covering the essential requirements under article 3.2 of the R&TTE Directive [1]. EN 302 217 series meet this demand by providing a rational subdivision of requirements into general, system dependent "not essential" and "essential" requirements from the perspective of the R&TTE Directive [1]. Part 1 includes system-independent common characteristics; these requirements are not essential under article 3.2 of the R&TTE Directive [1]. EN 302 217-2-2 [i.34], EN 302 217-3 [i.35] and EN 302 217-4-2 [i.37] are relevant to essential requirements under article 3.2 of the R&TTE Directive [1]. Additional system can be added for new available FS bands and for completing market available options. SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 6 In the present document, equipment is grouped into families of either similar frequency bands or applications. Five families are identified for frequency bands where frequency co-ordination is applied, corresponding, in both EN 302 217-2-1 [i.33] and EN 302 217-2-2 [i.34], to annexes referenced from A to E and one family associated with applications of packet data and combination of other signals mapped into proprietary transport modules, detailed in annex F. A frequency bands from 1,4 GHz to 2,7 GHz; B frequency bands from 3 GHz to 11 GHz (channel separation around 60 MHz and from 1,75 MHz up to around 30 MHz); C frequency bands from 3 GHz to 11 GHz (channel separation 40 MHz); D frequency bands 13 GHz, 15 GHz and 18 GHz; E frequency bands from 23 GHz to 55 GHz; Ea frequency bands from 71 GHz to 76 GHz and 81 GHz to 86 GHz (additional requirements when link-by-link coordination is applied); F definition of equivalent data rates for packet data, PDH/SDH and other signals on the traffic interface. In the same way EN 302 217-3 [i.35] three families are identified for frequency bands where either co-ordinated or uncoordinated deployment might be applied (see note), corresponding to annexes referenced from UA to UC. UA frequency band from 57 GHz to 59 GHz; UB frequency band from 64 GHz to 66 GHz; UBa frequency band from 57 GHz to 66 GHz (alternative, in overlapping bands, to UA and UB); UC frequency bands from 71 GHz to 76 GHz and 81 GHz to 86 GHz. NOTE: In these bands, CEPT administrations might have different views on the licensing and deployment requirements, ranging among uncoordinated, user self coordination (sometimes called "light licensing") or conventional link-by-link coordination. Therefore, from R&TTE Directive [1] point of view, the minimum of characteristics are considered among essential requirements, unless there is clear evidence that link-by-link coordination is the predominant method and additional requirements are consequently defined in EN 302 217-2-2 [i.34]; in this case, the supplier may chose between a "minimal" or a more complete assessment according the extension of the market addressed. (ii) Cross references to previously relevant ENs and TSs The EN 302 217 series replaced and superseded a number of older standards (frequency and/or capacity oriented), which remained, only as "historical" documents, in the ETSI data base. Provided that they may still be referenced in some documentation, annex C provides, for information, an overview of the correspondence between equipment considered in those standards and part/annexes in the present document. Table 2: Void (iii) Summary of system options provided A number of options for equipment implementation are identified in EN 302 217 series; the set of characteristics applicable to each option is uniquely identified through three parameters: • operating frequency band; • operating radio frequency channel separation (CS); • spectral efficiency class (as defined in EN 302 217-2-2 [i.34]). Each option so identified has a "nominal" payload requirement in term of minimum RIC (Radio Interface Capacity) to be fulfilled when packet payloads are used (e.g. Ethernet, ATM, etc.); in case PDH/SDH traffic are alternatively provided, annex F of EN 302 217-2-2 [i.34] gives the translation from the minimum RIC to the minimum hierarchic interfaces. SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 7 Table 3 summarizes the relevant cross-reference between channel separation in various Fixed Service frequency bands and the available options of equipment provided in EN 302 217 series. They are shown in term of the minimum RIC payload, which, depending on the channel separation, correspond to a specific spectral efficiency class detailed in clause 1.2 of EN 302 217-2-2 [i.34] (identified, with increasing spectral efficiency, as classes 1, 2, 3, 4L, 4H, 5L, 5H, 6L, 6H 7 and 8). In classes from 5 to 8, two further sub-classes suffix (i.e. A and B) are provided for the same channel separation depending on whether ACAP or CCDP operation is, respectively, considered for the equipment use. The minimum RIC payload in tables 3a and 3b are the minimum required for conformance to the present document and are based on the "minimum RIC density" defined, for each spectral efficiency class, in clause 1.2 of EN 302 217-2-2 [i.34]. Only some cases of systems in annex A, due to the smaller channel separation provided, are (exceptionally) labelled with typical gross bit rate rather than minimum RIC capacity rates. However, equipment may offer a variety of base band interfaces, e.g. typical hierarchical rates PDH or SDH, ISDN, Ethernet as well as mixture of these or other standardised interfaces. Mapping/multiplexing of the various base-band interfaces into common frame(s) suitable for radio transmission may be done using standardised higher hierarchical frames or other proprietary methods. Tables F.1a through F.1h in annex F of EN 302 217-2-2 [i.34] summarise the "minimum RIC" considered in the present document and, when only PDH or SDH interfaces are provided, give the equivalent capacity in term of number of 2 048 Mbit/s streams provided as multiple or single multiplexed PDH or SDH interfaces. These minimum capacities will be associated to the relevant channel separation and spectral efficiency classes defined. The cells in tables 3a and 3b are filled only on the basis of available physical single equipment transmission capacity (up to a minimum RIC of 862 Mbit/s for class 8 systems), which is relevant for R&TTE Directive [1] Art. 3.2 assessment. Doubled capacity is, in principle, possible for any option using CCDP operation or, more in general, subdividing the payload over two channels; however, specific test procedures are provided in EN 302 217-2-2 [i.34] only for STM-4 interface or other high speed data interfaces when their payload is split over more than one equipment. SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 8 Table 3a: Cross reference of available equipment and antenna requirements in parts and annexes of EN 302 217 series: Bands from 1,4 GHz to 18 GHz EN 302 217 series Common requirements
Part 1 (present document) (System independent common characteristics) Antenna requirements
Part 4-1 (Antenna general and complementary requirements) and
Part 4-2 (HS for R&TTED Art. 3.2 Antenna characteristics) Equipment requirements Part 2-1 (system-dependent complementary characteristics) and
Part 2-2 (HS for R&TTED Art. 3.2 equipment characteristics) Relevant annex in Part 2-1 and Part 2-2
A B or D C Frequency band (GHz) 1,4; 2,4 2,1; 2,6 1,4; 2,1; 2,6 2,1; 2,6 Annex B : 3,5 ; 4 ; U4 ; L6 ; U6 ; 7 ; 8 ; 10,5 ; 11
Annex D : 13 ; 15 ; 18 Annex B : U6 4, U4, U6, 8, 11 Minimum RIC (Mbit/s)
provided with relevant equipment characteristics Channel separation (MHz)
CS < 1,75 and 2 1,75 3,5 7 14 1,75 3,5 7 13,75 /
14 / 15 27,5 / 28 / 29 / 29,65 / 30 55 / 56 /
58 / 59,3 / 60 110
(note 1) 20 40 Spectral efficiency
Reference index
Class
1 1 (note 2)
2
2 2 (note 2) 2 4 8 16 2 4 8 16 32 64 128
3 3
3 6 12 24 48 96 191
4 4L (note 2) 4 8 16 32 4 8 16 32 64 128 256 45
5 4H
sSTM-14 (*) 24 49 98 196 392
6 5L
29 58
6 5LA, 5LB
117 235 470
168 7 5H
sSTM-22 (*) 34 68
7 5HA, 5HB
137 274 (**) 548
137 (***) 196 8 6L
39 78
8 6LA, 6LB
156 313 627
224 9 6H
88
9 6HA, 6HB
176 352 705
252 (**) 10 7
98
10 7A, 7B
196 392 784
280 11 8
107
8A, 8B
215 431 862
308 Equivalent capacity for hierarchic-only systems Annex F of parts 2-1 [i.33] and 2-2 [i.34] NOTE 1: CS 110 MHz available only in 18 GHz band. NOTE 2: For channel separations of 2 MHz and other various smaller than 1,75 MHz, only typical "gross bit rates" are defined. (*): These systems are intended only for the transport of subSTM-0 capacities only in 18 GHz band. (**): STM-4 capacity as combination of two 2 x STM-1 equipment operating on two channels in ACAP or CCDP or even non adjacent operation is also described. (***): Minimum RIC 137 Mbit/s option is special provision only for commonality of use of 5HB/28 MHz like equipment modulation also into 40 MHz channel arrangements.
SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 9 Table 3b: Cross reference of available equipment and antenna requirements in parts and annexes of EN 302 217 series: Bands from 23 GHz to 80 GHz EN 302 217 series Common requirements
Part 1 (present document) (System independent common characteristics) Antenna requirements
Part 4-1 (Antenna general and complementary requirements) and Part 4-2 (HS for R&TTED Art. 3.2 Antenna characteristics) Equipment requirements Part 2-1 (system-dependent complementary characteristics) and
Part 2-2 (HS for R&TTED Art. 3.2 equipment characteristics) Part 3 (R&TTED Art. 3.2 equipment characteristics) Relevant annex Part 2-2
E Ea (note 1) UA UB UBa UC Frequency band (GHz)
23, 26, 28, 31, 32, 38, 42 50, 52, 55 71 to 76 and 81 to 86 (note 1) 57 to 59 64 to 66 57 to 66 (note 2) 71 to 76 81 to 86 Minimum RIC (Mbit/s)
provided with relevant equipment characteristics Spectral efficiency
Channel separation (MHz) Channel separation (MHz) Channel separation (MHz) Channel size free or multiple of predefined slots Reference index
Class
3,5 7 14 28 56 112 3,5 7 14 28 56 250 500 750 1 000 1 250 1 500 1 750 2 000 1 1
2 4(***) 8(***) 16(***) 32(***) 142 285 427 570 712 855 997 1 140 See minimum spectral efficiency reported in the annexes. 2 2 4(**) 8 16 32 64 128 4 8 16 32 64(***) 285 570 855 1 140(*) 1 425 1 710 1 995 2 280 3 3
6(**) 12 24 48 96 191 6 12 24 48 96(***) 425 850 1 275 1 700 2 125(*) 2 550 2 975 3 400 4 4L 8(**) 16 32 64 128 256
16 32 64 128(***) 570 1 140(*) 1 710 2 280(*) 2 850
5 4H
24 49 98 196 392
875 1 750 2 625
6 5L
29 58
6 5LA, 5LB
117 235 470
1 050(*) 2 100(*) 3 150(*)
7 5H
34 68
7 5HA, 5HB
137 274 (****) 548
1 225 2 450
8 6L
39 78
8 6LA, 6LB
156 313 627
1 400 2 800
9 6H
88
9 6HA, 6HB
176 352 705
10 7
98
10 7A, 7B
196 392 784
11 8
107
11 8A, 8B
215 431 862
Equivalent capacity for hierarchic only systems Annexes F of parts 2-1 and 2-2 NOTE 1: Requirements for the bands 71 GHz to 76 GHz and 81 GHz to 86 GHz in annex Ea of Part 2-2 [i.34] are "additional" to those reported in annex UC of Part 3 [i.35]. NOTE 2: Alternative, in overlapping bands, to annexes UA and UB. (*): RIC rounded down to closest N × 1 Gbit/s rate shall also be considered valid. (**) Not provided in 42 GHz band. (***): Not provided in 50 GHz band. (****): STM-4 capacity as combination of two 2 x STM-1 equipment operating on two channels in ACAP or CCDP or even non adjacent operation is also described.
SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 10 (iv) User's guide The requirements applicable to a specific point to point digital fixed radio systems (including its antenna) are summarised in figure 0 showing the major structure of the whole EN 302 217 series. The requirements are subdivided across the six parts of the EN series corresponding to their four major categories. The first category (the present document) corresponds to "common" system independent characteristics which are either common to the whole family of equipment, i.e. performance and availability, environmental profiles, power supply, system block diagram, TMN interface, mechanical characteristics and baseband interfaces and parameters. The symbols and abbreviations, which apply to the EN 302 217 series, are listed in the present document. The present document defines those requirements and characteristics set out in the other parts of EN 302 217 series.
The second category (found in EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36]) corresponds to "complementary" characteristics and requirements, which are not relevant to article 3.2 of the R&TTE Directive [1] but may guarantee better performance to the actual deployed links. Therefore, the supplier may wish to claim compliance to all or some of these requirements for showing enhanced characteristics of its product. However, for completeness, EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36] provide comprehensive description of the "main" and "complementary" requirements, for equipment operating in co-ordinated frequency bands and for "antennas". Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of the R&TTE Directive [1] and are further detailed in EN 302 217-2-2 [i.34], for equipment operating in co-ordinated frequency bands, and EN 302 217-4-2 [i.37], for antennas. Complementary requirements are requirements that are not related to essential requirements under article 3.2 of the R&TTE Directive [1]. Nevertheless they are considered, having been commonly agreed for proper system operation and deployment when specific deployment conditions or compatibility requirements are present. Compliance to all or some of these requirements is made on a voluntary basis. The limits for main and complementary requirements that are not common or parameterized for all of the equipment covered by one part, but specific to one frequency range, one RIC or PDH/SDH capacity, etc., are located in annexes. The third category (EN 302 217-2-2 [i.34] and EN 302 217-4-2 [i.37]) is for equipment intended for frequency bands where link-by-link radio frequency coordination (either under administration control or required to the users in licensing procedure) over a specific radio frequency channels arrangement is generally used; it corresponds to essential phenomena, with respect to article 3.2 of the R&TTE Directive [1] and are consequently defined in harmonized standards. In this case a complete set of TX and RX parameters is retained essential and requirements are provided in the same format as in EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36]. The limiting values associated with the essential requirements which are not common to all of the equipment covered by one part, but specific to one frequency range, one RIC or PDH/SDH capacity, etc, are located in annexes. Reference to each annex is the same for EN 302 217-2-1 [i.33] as in EN 302 217-2-2 [i.34]. An HS-RTT (requirements table) summarizes those requirements to be addressed in order to claim compliance. The fourth category (EN 302 217-3 [i.35] and still EN 302 217-4-2 [i.37]) is for equipment intended for frequency bands where, for their propagation or regulatory nature, the conventional link-by-link radio frequency coordination is not generally used and a number of administrations may also apply less restrictive (and less protecting) regulatory measures. It still corresponds to essential phenomena, with respect to article 3.2 of the R&TTE Directive [1] and are consequently defined as harmonized standards. In this case a reduced set of TX and RX parameters is retained essential; however, when the coordinated deployment is considered predominant, additional set of requirements is further included in EN 302 217-2-2 [i.34] and the supplier may chose between the "minimal" or the more complete assessment according the extension of the market addressed. To conclude, EN 302 217 series will be used as a decision tree, from the present document down to the relevant annexes/sub-annexes of parts EN 302 217-2-1 [i.33], EN 302 217-2-2 [i.34] and EN 302 217-3 [i.35].
At every level, a check of compliance is recommended to be performed. SIST EN 302 217-1 V2.1.1:2013
ETSI ETSI EN 302 217-1 V2.1.1 (2013-07) 11 EN 302 217-2-1 System dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied 4 General characteristics 5 Main requirements 6 Complementary requirements Annex A Frequency bands 1,4 GHz to 2,7 GHz Annex B Frequency bands from 3 GHz to 11 GHz (CS up to 30 MHz) Annex C Frequency bands from 3 GHz
...
ETSI EN 302 217-1 V2.1.1 (2013-07)
European Standard
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview and system-independent
common characteristics
---------------------- Page: 1 ----------------------
2 ETSI EN 302 217-1 V2.1.1 (2013-07)
Reference
REN/ATTM-04016
Keywords
antenna, DFRS, digital, DRRS, FWA, point-to-
point, radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 217-1 V2.1.1 (2013-07)
Contents
Intellectual Property Rights . 4
Foreword . 4
Introduction . 5
1 Scope . 12
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 15
3 Definitions, symbols and abbreviations . 17
3.1 Definitions . 17
3.2 Symbols . 22
3.3 Abbreviations . 23
4 General characteristics . 26
4.1 Performance and availability requirements . 26
4.2 Environmental profiles . 26
4.2.1 Environmental profile declared under the R&TTE Directive . 26
4.2.2 ETSI environmental profiles . 26
4.2.2.1 Equipment within weather-protected locations (indoor locations) . 27
4.2.2.2 Equipment for not-weather-protected locations (outdoor locations) . 27
4.2.3 Test environment profiles . 27
4.3 Power supply . 27
4.3.1 Power supply profile declared under the R&TTE Directive . 27
4.3.2 ETSI power supply profile . 28
4.4 System block diagram . 28
5 Baseband interfaces and parameters . 28
5.1 Plesiochronous interfaces . 29
5.2 ISDN interfaces . 29
5.3 Synchronous digital hierarchy interfaces . 29
5.4 Other baseband data interfaces . 29
Annex A (informative): Miscellaneous characteristics . 30
A.1 Telecommunications Management Network (TMN) interface . 30
A.2 Mechanical characteristics . 30
Annex B (informative): Notification of interfaces under article 4.1 of the R&TTE Directive . 31
B.1 Applicability of TCAM-RIG format of radio interface specifications to Fixed Services . 31
B.2 Proposed list of radio interface specifications for Fixed Services . 32
Annex C (informative): Cross references to previously relevant ENs and TSs . 33
History . 36
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 217-1 V2.1.1 (2013-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below:
Part 1: "Overview and system-independent common characteristics";
Part 2-1: "System-dependent requirements for digital systems operating in frequency bands where frequency
co-ordination is applied";
Part 2-2: "Digital systems operating in frequency bands where frequency co-ordination is applied; Harmonized EN
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Equipment operating in frequency bands where both frequency coordinated or uncoordinated
deployment might be applied; Harmonized EN covering the essential requirements of article 3.2 of the
R&TTE";
Part 4-1: "System-dependent requirements for antennas";
Part 4-2: "Antennas; Harmonized EN covering the essential requirements of article 3.2 of R&TTE Directive".
National transposition dates
Date of adoption of this EN: 25 June 2013
Date of latest announcement of this EN (doa): 30 September 2013
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2014
Date of withdrawal of any conflicting National Standard (dow): 31 March 2014
Major variants with respect to previous published version
• System options identification has been changed, in line with corresponding changes in Parts 2-1 [i.33] and
2-2 [i.34] of EN 302 217. Old systems notations (A.1, … B.1, … C.1, … D.1, … E.1 ….) have been removed
and the system capacity is defined in term of minimum Radio Interface Capacity (RIC) rather than previous
hierarchic PDH/SDH interfaces. Each equipment in the scope of the present document refers to a coherent set
of transmitter and receiver requirements uniquely defined on the basis of the following identifying parameters:
1) operating frequency band;
2) operating radio frequency channel separation;
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 217-1 V2.1.1 (2013-07)
3) spectral efficiency class, to which the minimum RIC density is associated.
• Cross reference to older "historical" source ENs, no longer of interest has been moved to an annex.
• Required new and updated "definitions".
• Alignment of frequency bands and equipment options introduced in other parts of EN 302 217 series.
Introduction
(i) Generality and historical background
Digital Fixed Radio Systems (DFRS), used in European countries, had been historically specified in a relatively large
number of specific European Norms produced by ETSI.
Those previous documents, already superseded by first version of this EN 302 217 series, contained both essential
requirements and other requirements that, even if not considered essential under the Directive 1999/5/EC [1] of the
European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal
equipment and the mutual recognition of their conformity (hereafter mentioned as the R&TTE Directive) [1], may be
applicable.
Standards for point-to-point systems, including antennas, cover a very large range of traffic capacities, channel
separations (CS), modulation formats and applications over a very wide range of frequency bands that are summarized
in table 1.
Table 1: Digital Fixed Radio Systems (DFRS) parameters
Parameter Range
Frequency bands from 1 GHz to 86 GHz
Traffic capacities from 9,6 kbit/s to 622 Mbit/s and to Gigabit/s and above in the highest bands
Channel separations from 25 kHz to 112 MHz and to Gigahertz and above in the highest bands
Modulation formats from 2 to 2 048 states (amplitude and/or phase and/or frequency modulated
states)
Typical applications POINT-TO-POINT (P-P) CONNECTIONS:
rural and urban low/medium/high capacity links for mobile infrastructure,
transport/trunk (long haul), FWA/BWA/MWA backhaul, access, governmental
(non-military) links, private fixed networks, SAP/SAB P to P audio and video
links
STAND ALONE ANTENNAS:
for all of the above applications when integral antennas are not employed
The regulatory framework for placing radio systems on the market, established by the R&TTE Directive [1] also
requires the availability of Harmonized ENs covering the essential requirements under article 3.2 of the R&TTE
Directive [1]. EN 302 217 series meet this demand by providing a rational subdivision of requirements into general,
system dependent "not essential" and "essential" requirements from the perspective of the R&TTE Directive [1].
Part 1 includes system-independent common characteristics; these requirements are not essential under article 3.2 of the
R&TTE Directive [1].
EN 302 217-2-2 [i.34], EN 302 217-3 [i.35] and EN 302 217-4-2 [i.37] are relevant to essential requirements under
article 3.2 of the R&TTE Directive [1]. Additional system can be added for new available FS bands and for completing
market available options.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 217-1 V2.1.1 (2013-07)
In the present document, equipment is grouped into families of either similar frequency bands or applications. Five
families are identified for frequency bands where frequency co-ordination is applied, corresponding, in both
EN 302 217-2-1 [i.33] and EN 302 217-2-2 [i.34], to annexes referenced from A to E and one family associated with
applications of packet data and combination of other signals mapped into proprietary transport modules, detailed in
annex F.
A frequency bands from 1,4 GHz to 2,7 GHz;
B frequency bands from 3 GHz to 11 GHz (channel separation around 60 MHz and from 1,75 MHz up to around
30 MHz);
C frequency bands from 3 GHz to 11 GHz (channel separation 40 MHz);
D frequency bands 13 GHz, 15 GHz and 18 GHz;
E frequency bands from 23 GHz to 55 GHz;
Ea frequency bands from 71 GHz to 76 GHz and 81 GHz to 86 GHz (additional requirements when link-by-link
coordination is applied);
F definition of equivalent data rates for packet data, PDH/SDH and other signals on the traffic interface.
In the same way EN 302 217-3 [i.35] three families are identified for frequency bands where either co-ordinated or
uncoordinated deployment might be applied (see note), corresponding to annexes referenced from UA to UC.
UA frequency band from 57 GHz to 59 GHz;
UB frequency band from 64 GHz to 66 GHz;
UBa frequency band from 57 GHz to 66 GHz (alternative, in overlapping bands, to UA and UB);
UC frequency bands from 71 GHz to 76 GHz and 81 GHz to 86 GHz.
NOTE: In these bands, CEPT administrations might have different views on the licensing and deployment
requirements, ranging among uncoordinated, user self coordination (sometimes called "light licensing")
or conventional link-by-link coordination. Therefore, from R&TTE Directive [1] point of view, the
minimum of characteristics are considered among essential requirements, unless there is clear evidence
that link-by-link coordination is the predominant method and additional requirements are consequently
defined in EN 302 217-2-2 [i.34]; in this case, the supplier may chose between a "minimal" or a more
complete assessment according the extension of the market addressed.
(ii) Cross references to previously relevant ENs and TSs
The EN 302 217 series replaced and superseded a number of older standards (frequency and/or capacity oriented),
which remained, only as "historical" documents, in the ETSI data base. Provided that they may still be referenced in
some documentation, annex C provides, for information, an overview of the correspondence between equipment
considered in those standards and part/annexes in the present document.
Table 2: Void
(iii) Summary of system options provided
A number of options for equipment implementation are identified in EN 302 217 series; the set of characteristics
applicable to each option is uniquely identified through three parameters:
• operating frequency band;
• operating radio frequency channel separation (CS);
• spectral efficiency class (as defined in EN 302 217-2-2 [i.34]).
Each option so identified has a "nominal" payload requirement in term of minimum RIC (Radio Interface Capacity) to
be fulfilled when packet payloads are used (e.g. Ethernet, ATM, etc.); in case PDH/SDH traffic are alternatively
provided, annex F of EN 302 217-2-2 [i.34] gives the translation from the minimum RIC to the minimum hierarchic
interfaces.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 217-1 V2.1.1 (2013-07)
Table 3 summarizes the relevant cross-reference between channel separation in various Fixed Service frequency bands
and the available options of equipment provided in EN 302 217 series. They are shown in term of the minimum RIC
payload, which, depending on the channel separation, correspond to a specific spectral efficiency class detailed in
clause 1.2 of EN 302 217-2-2 [i.34] (identified, with increasing spectral efficiency, as classes 1, 2, 3, 4L, 4H, 5L, 5H,
6L, 6H 7 and 8). In classes from 5 to 8, two further sub-classes suffix (i.e. A and B) are provided for the same channel
separation depending on whether ACAP or CCDP operation is, respectively, considered for the equipment use.
The minimum RIC payload in tables 3a and 3b are the minimum required for conformance to the present document and
are based on the "minimum RIC density" defined, for each spectral efficiency class, in clause 1.2 of
EN 302 217-2-2 [i.34]. Only some cases of systems in annex A, due to the smaller channel separation provided, are
(exceptionally) labelled with typical gross bit rate rather than minimum RIC capacity rates.
However, equipment may offer a variety of base band interfaces, e.g. typical hierarchical rates PDH or SDH, ISDN,
Ethernet as well as mixture of these or other standardised interfaces. Mapping/multiplexing of the various base-band
interfaces into common frame(s) suitable for radio transmission may be done using standardised higher hierarchical
frames or other proprietary methods.
Tables F.1a through F.1h in annex F of EN 302 217-2-2 [i.34] summarise the "minimum RIC" considered in the present
document and, when only PDH or SDH interfaces are provided, give the equivalent capacity in term of number of
2 048 Mbit/s streams provided as multiple or single multiplexed PDH or SDH interfaces. These minimum capacities
will be associated to the relevant channel separation and spectral efficiency classes defined.
The cells in tables 3a and 3b are filled only on the basis of available physical single equipment transmission capacity
(up to a minimum RIC of 862 Mbit/s for class 8 systems), which is relevant for R&TTE Directive [1] Art. 3.2
assessment. Doubled capacity is, in principle, possible for any option using CCDP operation or, more in general,
subdividing the payload over two channels; however, specific test procedures are provided in EN 302 217-2-2 [i.34]
only for STM-4 interface or other high speed data interfaces when their payload is split over more than one equipment.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 217-1 V2.1.1 (2013-07)
Table 3a: Cross reference of available equipment and antenna requirements in parts and annexes of EN 302 217 series:
Bands from 1,4 GHz to 18 GHz
EN 302 217 series
Common requirements Part 1 (present document) (System independent common characteristics)
Part 4-1 (Antenna general and complementary requirements) and
Antenna requirements
Part 4-2 (HS for R&TTED Art. 3.2 Antenna characteristics)
Part 2-1 (system-dependent complementary characteristics) and
Equipment requirements
Part 2-2 (HS for R&TTED Art. 3.2 equipment characteristics)
Relevant annex in Part 2-1 and
A B or D C
Part 2-2
1,4; Annex B : 3,5 ; 4 ; U4 ; L6 ; U6 ; 7 ; 8 ; 10,5 ; 11 Annex B : 4, U4,
Frequency band (GHz) 1,4; 2,4 2,1; 2,6 2,1; 2,6
Annex D : 13 ; 15 ; 18
2,1; 2,6 U6 U6, 8, 11
Channel
27,5 / 28 / 55 / 56 /
separation (MHz)
CS < 1,75 13,75 / 110
1,75 3,5 7 14 1,75 3,5 7 29 / 29,65 / 58 / 59,3 / 20 40
and 2 14 / 15 (note 1)
Spectral efficiency
30 60
Reference index Class
1 1 (note 2) 2
2 2 (note 2) 2 4 8 16
2 4 8 16 32 64 128
3 3 3 6 12 24 48 96 191
4 4L (note 2) 4 8 16 32 4 8 16 32 64 128 256 45
5 4H sSTM-14 (*) 24 49 98 196 392
6 5L 29 58
6 5LA, 5LB 117 235 470 168
7 5H sSTM-22 (*) 34 68
137 (***)
7 5HA, 5HB 137 274 (**) 548
196
8 6L 39 78
8 6LA, 6LB 156 313 627 224
9 6H 88
9 6HA, 6HB
176 352 705 252 (**)
10 7 98
10 7A, 7B 196 392 784 280
11 8
107
8A, 8B 215 431 862 308
Equivalent capacity for
Annex F of parts 2-1 [i.33] and 2-2 [i.34]
hierarchic-only systems
NOTE 1: CS 110 MHz available only in 18 GHz band.
NOTE 2: For channel separations of 2 MHz and other various smaller than 1,75 MHz, only typical "gross bit rates" are defined.
(*): These systems are intended only for the transport of subSTM-0 capacities only in 18 GHz band.
(**): STM-4 capacity as combination of two 2 x STM-1 equipment operating on two channels in ACAP or CCDP or even non adjacent operation is also described.
(***): Minimum RIC 137 Mbit/s option is special provision only for commonality of use of 5HB/28 MHz like equipment modulation also into 40 MHz channel arrangements.
ETSI
Minimum RIC (Mbit/s)
provided with relevant equipment characteristics
---------------------- Page: 8 ----------------------
9 ETSI EN 302 217-1 V2.1.1 (2013-07)
Table 3b: Cross reference of available equipment and antenna requirements in parts and annexes of EN 302 217 series:
Bands from 23 GHz to 80 GHz
EN 302 217 series
Common requirements Part 1 (present document) (System independent common characteristics)
Antenna requirements Part 4-1 (Antenna general and complementary requirements) and Part 4-2 (HS for R&TTED Art. 3.2 Antenna characteristics)
Part 3 (R&TTED
Part 2-1 (system-dependent complementary characteristics) and
Equipment requirements Art. 3.2 equipment
Part 2-2 (HS for R&TTED Art. 3.2 equipment characteristics)
characteristics)
Relevant annex Part 2-2 E Ea (note 1) UA UB UBa UC
Frequency band (GHz) 23, 26, 28, 31, 32, 38, 42 50, 52, 55 71 to 76 and 81 to 86 (note 1)
Spectral efficiency Channel separation (MHz) Channel separation (MHz) Channel separation (MHz)
Channel size free
or multiple of
Reference Class
3,5 7 14 28 56 112 3,5 7 14 28 56
predefined slots
index
1 1 2 4(***) 8(***) 16(***) 32(***) 142 285 427 570 712 855 997 1 140
2 2 4(**) 8 16 32 64 128 4 8 16 32 64(***) 285 570 855 1 140(*) 1 425 1 710 1 995 2 280
3 3 6(**) 12 24 48 96 191 6 12 24 48 96(***) 425 850 1 275 1 700 2 125(*) 2 550 2 975 3 400
4 4L 8(**) 16 32 64 128 256 16 32 64 128(***) 570 1 140(*) 1 710 2 280(*) 2 850
5 4H 24 49 98 196 392 875 1 750 2 625
6 5L
29 58
6 5LA, 5LB 117 235 470 1 050(*) 2 100(*) 3 150(*)
7 5H 34 68
See minimum
274 spectral efficiency
7 5HA, 5HB 137 548 1 225 2 450
(****) reported in the
annexes.
8 6L
39 78
8 6LA, 6LB 156 313 627 1 400 2 800
9 6H 88
9 6HA, 6HB 176 352 705
10 7 98
10 7A, 7B 196 392 784
11 8 107
11 8A, 8B 215 431 862
Equivalent capacity for
Annexes F of parts 2-1 and 2-2
hierarchic only systems
NOTE 1: Requirements for the bands 71 GHz to 76 GHz and 81 GHz to 86 GHz in annex Ea of Part 2-2 [i.34] are "additional" to those reported in annex UC of Part 3 [i.35].
NOTE 2: Alternative, in overlapping bands, to annexes UA and UB.
(*): RIC rounded down to closest N × 1 Gbit/s rate shall also be considered valid.
(**) Not provided in 42 GHz band.
(***): Not provided in 50 GHz band.
(****): STM-4 capacity as combination of two 2 x STM-1 equipment operating on two channels in ACAP or CCDP or even non adjacent operation is also described.
ETSI
Minimum RIC (Mbit/s)
provided with relevant equipment characteristics
250
500
750
1 000
1 250
1 500
1 750
2 000
57 to 59
64 to 66
57 to 66
(note 2)
71 to 76
81 to 86
---------------------- Page: 9 ----------------------
10 ETSI EN 302 217-1 V2.1.1 (2013-07)
(iv) User's guide
The requirements applicable to a specific point to point digital fixed radio systems (including its antenna) are
summarised in figure 0 showing the major structure of the whole EN 302 217 series. The requirements are subdivided
across the six parts of the EN series corresponding to their four major categories.
The first category (the present document) corresponds to "common" system independent characteristics which are
either common to the whole family of equipment, i.e. performance and availability, environmental profiles, power
supply, system block diagram, TMN interface, mechanical characteristics and baseband interfaces and parameters. The
symbols and abbreviations, which apply to the EN 302 217 series, are listed in the present document. The present
document defines those requirements and characteristics set out in the other parts of EN 302 217 series.
The second category (found in EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36]) corresponds to "complementary"
characteristics and requirements, which are not relevant to article 3.2 of the R&TTE Directive [1] but may guarantee
better performance to the actual deployed links. Therefore, the supplier may wish to claim compliance to all or some of
these requirements for showing enhanced characteristics of its product.
However, for completeness, EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36] provide comprehensive description of the
"main" and "complementary" requirements, for equipment operating in co-ordinated frequency bands and for
"antennas".
Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of the
R&TTE Directive [1] and are further detailed in EN 302 217-2-2 [i.34], for equipment operating in co-ordinated
frequency bands, and EN 302 217-4-2 [i.37], for antennas.
Complementary requirements are requirements that are not related to essential requirements under article 3.2 of the
R&TTE Directive [1]. Nevertheless they are considered, having been commonly agreed for proper system operation and
deployment when specific deployment conditions or compatibility requirements are present. Compliance to all or some
of these requirements is made on a voluntary basis.
The limits for main and complementary requirements that are not common or parameterized for all of the equipment
covered by one part, but specific to one frequency range, one RIC or PDH/SDH capacity, etc., are located in annexes.
The third category (EN 302 217-2-2 [i.34] and EN 302 217-4-2 [i.37]) is for equipment intended for frequency bands
where link-by-link radio frequency coordination (either under administration control or required to the users in licensing
procedure) over a specific radio frequency channels arrangement is generally used; it corresponds to essential
phenomena, with respect to article 3.2 of the R&TTE Directive [1] and are consequently defined in harmonized
standards. In this case a complete set of TX and RX parameters is retained essential and requirements are provided in
the same format as in EN 302 217-2-1 [i.33] and EN 302 217-4-1 [i.36]. The limiting values associated with the
essential requirements which are not common to all of the equipment covered by one part, but specific to one frequency
range, one RIC or PDH/SDH capacity, etc, are located in annexes. Reference to each annex is the same for
EN 302 217-2-1 [i.33] as in EN 302 217-2-2 [i.34]. An HS-RTT (requirements table) summarizes those requirements to
be addressed in order to claim compliance.
The fourth category (EN 302 217-3 [i.35] and still EN 302 217-4-2 [i.37]) is for equipment intended for frequency
bands where, for their propagation or regulatory nature, the conventional link-by-link radio frequency coordination is
not generally used and a number of administrations may also apply less restrictive (and less protecting) regulatory
measures. It still corresponds to essential phenomena, with respect to article 3.2 of the R&TTE Directive [1] and are
consequently defined as harmonized standards. In this case a reduced set of TX and RX parameters is retained essential;
however, when the coordinated deployment is considered predominant, additional set of requirements is further
included in EN 302 217-2-2 [i.34] and the supplier may chose between the "minimal" or the more complete assessment
according the extension of the market addressed.
To conclude, EN 302 217 series will be used as a decision tree, from the present document down to the relevant
annexes/sub-annexes of parts EN 302 217-2-1 [i.33], EN 302 217-2-2 [i.34] and EN 302 217-3 [i.35].
At every level, a check
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.