SIST EN ISO 13688:2013/kFprA1:2020
(Amendment)Protective clothing - General requirements - Amendment 1 (ISO 13688:2013/FDAM 1:2020)
Protective clothing - General requirements - Amendment 1 (ISO 13688:2013/FDAM 1:2020)
2021-03-01 - Lack of compliance - publication on hold
Schutzkleidung - Allgemeine Anforderungen - Änderung 1 (ISO 13688:2013/FDAM 1:2020)
[Not available]
Vêtements de protection - Exigences générales - Amendement 1 (ISO 13688:2013/FDAM 1:2020)
Varovalna obleka - Splošne zahteve - Dopolnilo A1 (ISO 13688:2013/FDAM 1:2020)
General Information
RELATIONS
Standards Content (sample)
SLOVENSKI STANDARD
SIST EN ISO 13688:2013/oprA1:2019
01-oktober-2019
Varovalna obleka - Splošne zahteve - Dopolnilo A1 (ISO 13688:2013/DAM 1:2019)
Protective clothing - General requirements - Amendment 1 (ISO 13688:2013/DAM
1:2019)
Schutzkleidung - Allgemeine Anforderungen - Änderung 1 (ISO 13688:2013/DAM
1:2019)
Vêtements de protection - Exigences générales - Amendement 1 (ISO 13688:2013/DAM
1:2019)
Ta slovenski standard je istoveten z: EN ISO 13688:2013/prA1
ICS:
13.340.10 Varovalna obleka Protective clothing
SIST EN ISO 13688:2013/oprA1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST EN ISO 13688:2013/oprA1:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 13688:2013/oprA1:2019
DRAFT AMENDMENT
ISO 13688:2013/DAM 1
ISO/TC 94/SC 13 Secretariat: SNV
Voting begins on: Voting terminates on:
2019-08-15 2019-11-07
Protective clothing — General requirements
AMENDMENT 1
Vêtements de protection — Exigences générales
AMENDEMENT 1
ICS: 13.340.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 13688:2013/DAM 1:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
SIST EN ISO 13688:2013/oprA1:2019
ISO 13688:2013/DAM 1:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
SIST EN ISO 13688:2013/oprA1:2019
ISO 13688:2013/DAM 1:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
The committee responsible for this document is ISO/TC 94/SC 13, Protective clothing.
© ISO 2019 – All rights reserved iii---------------------- Page: 5 ----------------------
SIST EN ISO 13688:2013/oprA1:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 13688:2013/oprA1:2019
ISO 13688:2013/DAM 1:2019(E)
Protective clothing — General requirements
AMENDMENT 1
1 Modification to Foreword
Replace
“— Additional definitions on waist to waist over the shoulder length, and torso.”
with“— Additional definitions on waist to waist over the shoulder line, and torso."
2 Modification to Clause 2, “Normative references”
Replace
“ISO 3635, Size designation of clothes — Definitions and body measurement procedure
EN 14362-1, Textiles — Methods for determination of certain aromatic amines der...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.