13.340.10 - Protective clothing
ICS 13.340.10 Details
Protective clothing
Schutzkleidung
Vetements de protection
Varovalna obleka
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 13.340.10 - Protective clothing
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies a test method for determining the resistance of complete protective clothing to inward leakage of liquid chemicals (protective clothing integrity). This method specifies an alternative method for determining the resistance to spray penetration because it uses a static manikin instead of a test subject; it also uses a different spray configuration and duration than the other methods within ISO 17491 series. This test method is aligned with ASTM F1359 since the only laboratories with equipment of this kind are performing testing according to that standard. This test method is not appropriate for evaluating the permeation or penetration of liquid chemicals through the material from which the clothing is made.
- Standard11 pagesEnglish languagesale 15% off
This document specifies the overall requirements, equipment and calculation methods to provide results that can be used for evaluating the performance of complete garments or protective clothing ensembles exposed to short duration flame engulfment.
This test method establishes a rating system to characterize the thermal protection provided by single-layer and multi-layer garments made of flame resistant materials. The rating is based on the measurement of heat transfer to a full-size manikin exposed to convective and radiant energy in a laboratory simulation of a fire with controlled heat flux, duration and flame distribution. The heat transfer data is summed over a prescribed time to give the total transferred energy. Transferred energy and thermal manikin protection factor (TMPF) assessment methods provide a means to quantify product performance.
The exposure heat flux is limited to a nominal level of 84 kW/m2 and durations of 3 s to 20 s dependant on the risk assessment and expectations from the thermal insulating capability of the garment.
The results obtained apply only to the particular garments or ensembles, as tested, and for the specified conditions of each test, particularly with respect to the heat flux, duration and flame distribution.
This test method covers visual evaluation, observation, inspection and documentation on the overall behaviour of the test specimen(s) before, during and after the exposure. The effects of body position and movement are not addressed in this test method.
The heat flux measurements can also be used to calculate the predicted skin burn injury resulting from the exposure (see ISO 13506-2).
This test method does not simulate high radiant exposures such as those found in arc flash exposures, some types of fire exposures where liquid or solid fuels are involved, nor exposure to nuclear explosions.
NOTE This test method is complex and requires a high degree of technical expertise in both the test setup and operation. Even minor deviations from the instructions in this test method can lead to significantly different test results.
- Draft51 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides technical details for calculating predicted burn injury to human skin when its surface is subject to a varying heat flux, such as may occur due to energy transmitted through and by a garment or protective clothing ensemble exposed to flames. A series of test cases are provided against which the burn injury prediction calculation method is verified. It also contains requirements for the in situ calibration of the thermal energy sensor — skin injury prediction system for the range of heat fluxes that occur under garments.
The skin burn injury calculation methods as presented in this test method do not include terms for handling short wavelength radiation that may penetrate the skin. The latter include arc flashes, some types of fire exposures with liquid or solid fuels, and nuclear sources.
- Draft23 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies minimum safety requirements and test methods for protective clothing including hoods, aprons, sleeves, and gaiters that are designed to protect the wearer's body including head (hoods) and feet (gaiters) and that are to be worn during welding and allied processes with comparable risks. For the protection of the wearer’s head and feet, this document is only applicable to hoods and gaiters. This document does not cover requirements for feet, hand, face, and/or eye protectors. This type of protective clothing is intended to protect the wearer against the following hazards: — spatter (small splashes of molten metal) in 2 risk levels, short contact time with flame, radiant heat from an electric arc used for welding and allied processes, — harmful artificial optical radiation (UV-A, UV-B and especially UV-C) in 3 risk levels generated during welding and allied processes and — minimizes the possibility of electrical shock by short-term, accidental contact with live electrical conductors at voltages up to approximately 100 V d. c. in normal conditions of welding. Sweat, soiling, or other contaminants can affect the level of protection provided against short-term accidental contact with live electric conductors at these voltages. The main manual welding processes are exemplified and are classified into process groups according to the maximum effectively emitted total irradiance, which has been determined and evaluated by measurement for these types of welding processes. For adequate overall protection against the risks to which welders are likely to be exposed, personal protective equipment (PPE) covered by other standards should additionally be worn to protect the head, face, hands, and feet. This document is not applicable for laser welding processes (coherent, monochromatic radiation sources). Guidance for the selection of protective clothing for different welding activities is detailed in Annex B.
- Standard43 pagesEnglish languagesale 15% off
- Standard49 pagesFrench languagesale 15% off
This document specifies a test method for determining the liquid tightness of clothing for protection against rain, using a static manikin exposed to large amount of high energy droplets from above. It is applicable to the testing of jackets, trousers, coats and one- or two-piece suits.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the test method for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity:
a) Method A: low-level spray test. This is applicable to clothing that covers the full body surface and is intended to be worn when there is a potential risk of exposure to small quantities of spray or accidental low-volume splashes of a liquid chemical.
b) Method B: high-level spray test. This is applicable to clothing with spray-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment, which covers the full body surface and which is intended to be worn when there is a risk of exposure to sprayed liquid chemical.
This document does not apply to chemical permeation resistance of the materials from which the chemical protective clothing is made.
- Draft25 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides technical details for calculating predicted burn injury to human skin when its surface is subject to a varying heat flux, such as may occur due to energy transmitted through and by a garment or protective clothing ensemble exposed to flames. A series of test cases are provided against which the burn injury prediction calculation method is verified. It also contains requirements for the in situ calibration of the thermal energy sensor — skin injury prediction system for the range of heat fluxes that occur under garments. The skin burn injury calculation methods as presented in this test method do not include terms for handling short wavelength radiation that may penetrate the skin. The latter include arc flashes, some types of fire exposures with liquid or solid fuels, and nuclear sources.
- Standard18 pagesEnglish languagesale 15% off
- Standard18 pagesFrench languagesale 15% off
This document specifies the overall requirements, equipment and calculation methods to provide results that can be used for evaluating the performance of complete garments or protective clothing ensembles exposed to short duration flame engulfment. This test method establishes a rating system to characterize the thermal protection provided by single-layer and multi-layer garments made of flame resistant materials. The rating is based on the measurement of heat transfer to a full-size manikin exposed to convective and radiant energy in a laboratory simulation of a fire with controlled heat flux, duration and flame distribution. The heat transfer data is summed over a prescribed time to give the total transferred energy. Transferred energy and thermal manikin protection factor (TMPF) assessment methods provide a means to quantify product performance. The exposure heat flux is limited to a nominal level of 84 kW/m2 and durations of 3 s to 20 s dependant on the risk assessment and expectations from the thermal insulating capability of the garment. The results obtained apply only to the particular garments or ensembles, as tested, and for the specified conditions of each test, particularly with respect to the heat flux, duration and flame distribution. This test method covers visual evaluation, observation, inspection and documentation on the overall behaviour of the test specimen(s) before, during and after the exposure. The effects of body position and movement are not addressed in this test method. The heat flux measurements can also be used to calculate the predicted skin burn injury resulting from the exposure (see ISO 13506-2). This test method does not simulate high radiant exposures such as those found in arc flash exposures, some types of fire exposures where liquid or solid fuels are involved, nor exposure to nuclear explosions. NOTE This test method is complex and requires a high degree of technical expertise in both the test setup and operation. Even minor deviations from the instructions in this test method can lead to significantly different test results.
- Standard44 pagesEnglish languagesale 15% off
- Standard52 pagesFrench languagesale 15% off
This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same chemical protective barrier requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the test method for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity: a) Method A: low-level spray test. This is applicable to clothing that covers the full body surface and is intended to be worn when there is a potential risk of exposure to small quantities of spray or accidental low-volume splashes of a liquid chemical. b) Method B: high-level spray test. This is applicable to clothing with spray-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment, which covers the full body surface and which is intended to be worn when there is a risk of exposure to sprayed liquid chemical. This document does not apply to chemical permeation resistance of the materials from which the chemical protective clothing is made.
- Standard18 pagesEnglish languagesale 15% off
- Standard19 pagesFrench languagesale 15% off
This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same chemical protective barrier requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for determining the liquid tightness of clothing for protection against rain, using a static manikin exposed to large amount of high energy droplets from above. It is applicable to the testing of jackets, trousers, coats and one- or two-piece suits.
This document is not applicable to the testing of garments for resistance to other weather conditions, e.g. snow, hail-, or strong winds.
NOTE For general background of the rain simulation, see Annex A.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for determining the liquid tightness of clothing for protection against rain, using a static manikin exposed to large amount of high energy droplets from above. It is applicable to the testing of jackets, trousers, coats and one- or two-piece suits. This document is not applicable to the testing of garments for resistance to other weather conditions, e.g. snow, hail-, or strong winds. NOTE For general background of the rain simulation, see Annex A.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document sets out the best practices for the selection and use of PPE designed to provide protection for firefighters while carrying out their duties. The PPE covered in this document is intended for firefighting personnel exposed to risks associated with but not necessarily limited to the following activities: — structural firefighting; — wildland firefighting; — incidents involving hazardous materials; — incidents involving motor vehicle; — urban search and rescue. The purpose of this document is to highlight the main areas that a fire service needs to consider when providing PPE to its members. This document is a supplement to the information provided in the PPE standards or used in conjunction with them. Most paragraphs of the document contain bullet lists, these lists are provided for guidance only and they are not exhaustive. Cleaning, inspection and repair of firefighters' personal protective equipment (including care and maintenance) are covered by ISO 23616.
- Technical report60 pagesEnglish languagesale 15% off
This document contains a list of terms which are frequently used in the standardisation of protective clothing and protective equipment worn on the body, including hand and arm protection and lifejackets, and definitions of these terms.
The definitions are intended to support an unambiguous use of the terms listed.
This document is intended to serve as a reference document for the Working Groups of CEN/TC 162 and ISO/TC 94/SC 13 to ascertain what definitions already exist and may be used for setting up new standards and to provide guidance in the elaboration of new definitions.
- Standard83 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft160 pagesEnglish, French and German languagesale 10% offe-Library read for1 day
This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings. When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product. This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.
- Standard23 pagesEnglish languagesale 15% off
- Standard24 pagesFrench languagesale 15% off
This European Standard specifies requirements and test methods for the performance of garments for protection against the effects of cool environments above −5 °C (see Annex C). These effects comprise not only low air temperatures, but also humidity and air velocity.
Cold protective ensembles are excluded from this standard.
The protective effects and requirements of footwear, gloves and separate head wear are excluded from the scope of this standard.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for constant wear lifejackets for use by helicopter crew members and passengers in the event of a ditching or water impact, to ensure minimum levels of performance. It only applies to constant wear lifejackets for use by adults and that are intended to be manually inflated after leaving the helicopter.
Helicopter constant wear lifejackets are designed to be worn with or without a helicopter immersion suit and/or emergency breathing system.
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
This technical document specifies requirements for immersion suits for use by helicopter crew members and passengers in the event of a ditching or water impact, to ensure minimum levels of performance. It applies to immersion suits for use by adults only.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
This document contains a list of terms which are frequently used in the standardization of protective clothing (5.1.4) and protective equipment worn on the body, including hand and arm protection and lifejackets, and definitions of these terms.
The definitions are intended to support an unambiguous use of the terms listed.
This document is intended to serve as a reference document for the Working Groups of CEN/TC 162 and ISO/TC 94/SC 13 to ascertain what definitions already exist and may be used for setting up new standards and to provide guidance in the elaboration of new definitions.
NOTE - In addition to text written in the official ISO languages (English, French), this document gives text in German. This text is published under the responsibility of the Member Body for Germany (DIN) and is given for information only. Only the text given in the official languages can be considered as ISO text.
- Standard83 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft160 pagesEnglish, French and German languagesale 10% offe-Library read for1 day
This document contains a list of terms which are frequently used in the standardization of protective clothing (5.1.4) and protective equipment worn on the body, including hand and arm protection and lifejackets, and definitions of these terms. The definitions are intended to support an unambiguous use of the terms listed. This document is intended to serve as a reference document for the Working Groups of CEN/TC 162 and ISO/TC 94/SC 13 to ascertain what definitions already exist and may be used for setting up new standards and to provide guidance in the elaboration of new definitions. NOTE - In addition to text written in the official ISO languages (English, French), this document gives text in German. This text is published under the responsibility of the Member Body for Germany (DIN) and is given for information only. Only the text given in the official languages can be considered as ISO text.
- Standard220 pagesEnglish languagesale 15% off
- Standard220 pagesGerman languagesale 15% off
- Standard220 pagesFrench languagesale 15% off
- Standard220 pagesSlovenian, English, German and French languagesale 15% off
This document specifies requirements for constant wear lifejackets for use by helicopter crew members and passengers in the event of a ditching or water impact, to ensure minimum levels of performance. It only applies to constant wear lifejackets for use by adults and that are intended to be manually inflated after leaving the helicopter.
Helicopter constant wear lifejackets are sometimes designed to be worn with or without a helicopter immersion suit and/or emergency breathing system.
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for immersion suits for use by helicopter crew members and passengers in the event of a ditching or water impact, to ensure minimum levels of performance. It applies to immersion suits for use by adults only.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements and test methods for the performance of garments for protection against the effects of cool environments above −5 °C (see Annex C). These effects comprise not only low air temperatures, but also humidity and air velocity.
Cold protective ensembles are excluded from this standard.
The protective effects and requirements of footwear, gloves and separate head wear are excluded from the scope of this standard.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies two complementary methods (method A and method B) for determining the
behaviour of materials for heat protective clothing subjected to heat radiation.
These tests are carried out on representative single or multi-layer textiles or other materials intended
for clothing for protection against heat. They are also applicable to assemblies, which correspond to the
overall build up of a heat protective clothing assembly with or without underclothing,
Method A serves for visual assessment of any changes in the material after the action of heat radiation.
With method B the protective effect of the materials is determined. The materials may be tested either
by both methods or only by one of them.
The tests according to these two methods serve to classify materials; however, to be able to make a
statement or prediction as to the suitability of a material for protective clothing additional criteria
must be taken into account.
Since the tests are carried out at room temperature the results do not necessarily correspond to the
behaviour of the materials at higher ambient temperatures and therefore are only to a limited extent
suitable for predicting the performance of the protective clothing made from the materials under test.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document applies to garments and assembly of garments providing protection against heat and flame, with integrated smart textiles and non-textile elements for enhanced health, safety and survival capabilities.
This document does not concern validating claims that the integrated smart textile and non-textile elements substitute directly any protection provided by the garment from a heat and flame perspective.
The integrated smart textiles and non-textile elements could include not only the parts integrated into the protective garment but also connections to transmit the data generated or exchange data with external devices. It is not within the scope of this document to evaluate either the data storage or transmission (including connectivity) to the external devices, nor the external devices. This document evaluates only the smart textiles and non-textile elements integrated into the garment.
This document supplements the requirements of EN ISO 11612 and EN ISO 13688 and does not replace any of the requirements cited in those documents.
This document sets additional testing and performance requirements linked specifically to the garments and assembly of garments providing protection against heat and flame, with integrated smart textiles and non-textile elements for enhanced health, safety and survival capabilities. These additional requirements will depend on the functionality of the smart textile or non-textile element and its needed efficacy during heat and flame hazards and risks from an electrical/electronic safety perspective in these situations.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies two complementary methods (method A and method B) for determining the behaviour of materials for heat protective clothing subjected to heat radiation.
These tests are carried out on representative single or multi-layer textiles or other materials intended for clothing for protection against heat. They are also applicable to assemblies, which correspond to the overall build up of a heat protective clothing assembly with or without underclothing,
Method A serves for visual assessment of any changes in the material after the action of heat radiation. With method B the protective effect of the materials is determined. The materials may be tested either by both methods or only by one of them.
The tests according to these two methods serve to classify materials; however, to be able to make a statement or prediction as to the suitability of a material for protective clothing additional criteria must be taken into account.
Since the tests are carried out at room temperature the results do not necessarily correspond to the behaviour of the materials at higher ambient temperatures and therefore are only to a limited extent suitable for predicting the performance of the protective clothing made from the materials under test.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document applies to garments and assembly of garments providing protection against heat and flame, with integrated smart textiles and non-textile elements for enhanced health, safety and survival capabilities.
This document does not concern validating claims that the integrated smart textiles and non-textile elements substitute directly any protection provided by the garment from a heat and flame perspective.
The integrated smart textiles and non-textile elements could include not only the parts integrated into the protective garment but also connections to transmit the data generated or exchange data with external devices. It is not within the scope of this document to evaluate either the data storage or transmission (including connectivity) to the external devices, nor the external devices. This document evaluates only the smart textiles and non-textile elements integrated into the garment.
This document supplements the requirements of EN ISO 11612 and EN ISO 13688 and does not replace any of the requirements cited in those documents.
This document sets additional testing and performance requirements linked specifically to the garments and assembly of garments providing protection against heat and flame, with integrated smart textiles and non-textile elements for enhanced health, safety and survival capabilities. These additional requirements will depend on the functionality of the smart textiles or non-textile element and its needed efficacy during heat and flame hazards and risks from an electrical/electronic safety perspective in these situations.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies two complementary methods (method A and method B) for determining the behaviour of materials for heat protective clothing subjected to heat radiation. These tests are carried out on representative single or multi-layer textiles or other materials intended for clothing for protection against heat. They are also applicable to assemblies, which correspond to the overall build up of a heat protective clothing assembly with or without underclothing, Method A serves for visual assessment of any changes in the material after the action of heat radiation. With method B the protective effect of the materials is determined. The materials may be tested either by both methods or only by one of them. The tests according to these two methods serve to classify materials; however, to be able to make a statement or prediction as to the suitability of a material for protective clothing additional criteria must be taken into account. Since the tests are carried out at room temperature the results do not necessarily correspond to the behaviour of the materials at higher ambient temperatures and therefore are only to a limited extent suitable for predicting the performance of the protective clothing made from the materials under test.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
- Amendment10 pagesEnglish languagesale 10% offe-Library read for1 day
This document gives requirements, guidance and recommendations for the cleaning, inspection, and repair of PPE for use by firefighters. This document is intended to be used by those responsible for the cleaning, inspections, and repair of firefighters PPE, however, it will also provide vital guidance to those who are responsible for establishing such a programme including fire and rescue services. This document does not cover the following at this time: a) chemical protective clothing; b) garments required for protection against chemical, biological, radiological and nuclear (CBRN) materials.
- Standard37 pagesEnglish languagesale 15% off
2021-03-01 - Lack of compliance - publication on hold
- Amendment15 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment10 pagesEnglish languagesale 10% offe-Library read for1 day
2021-03-01 - Lack of compliance - publication on hold
- Amendment15 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
This document establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document covers the management and control of rehabilitation activities.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
The purpose of this document is to assist employers (or the person who advises the employer such as suppliers of PPE or services, inspection, insurance companies, etc.) in taking the necessary decisions regarding the selection, use, care and maintenance (SUCAM) of advanced garments and ensembles of garments that provide protection against heat and flame, with integrated smart textiles and smart non-textile elements for enhanced health, safety and survival capabilities that are compliant with the European legislation.
This document supports developers and manufacturers in designing and producing garments with smart textiles and smart non-textile elements that will meet the user’s needs during the whole life cycle of the garment and comply with standard requirements set for protective clothing on use, care and maintenance up to and including the disposal of the protective gear.
This document is not exhaustive in addressing all the safety concerns associated with the use of compliant protective equipment for protection against heat and flames and other related risks.
It is essential not to construe this document as addressing all the safety concerns, if any, associated with the use of this document by testing or repair facilities. It is the responsibility of the persons and organizations that use this document and any other standards or technical report related to PPE:
- to conduct a risk assessment at the workplace;
- to select the protective clothing and other PPE, including those with smart (intelligent) features, and to verify that the manufacturer has indicated the selected PPE to be suitable for the identified risks at the workplace;
- as well as to ensure that these provide a holistic protection, only when the compatibility has been assessed including understanding the workplace and the work environment to determine the properties of protective clothing against heat and flames to establish health and safety practices;
- to verify that the manufacturer has provided information for risk assessment of the potential risks that may occur due to the smart (intelligent) features in the intended working environment, and that the manufacturer has suggested measurements to compensate such new risks, whilst the employer has to ensure that these measurements are brought to action;
- and to determine the applicability of regulatory limitations prior to using this document for any designing, manufacturing, and testing.
This document is meant for all end users that are using smart garments for protection against heat and flame. It contains information that can also be useful to other people, such as manufacturers, designers, service providers and educators who may be confronted with smart garments used to protect against heat and flame risks although it will focus on the first four in the list below:
- petrochemical and chemical industry;
- welders and foundries;
- utilities (electrical, gas, water);
- fire fighters and emergency response;
- sports (motor sports, boating, etc.);
- security forces (military, police and private).
It is essential that nothing herein restricts any jurisdiction from exceeding the minimum requirements as provided in the relevant standards.
This document is not intended to cover the aspects related to data security and privacy. For employers using smart garments that monitor and/or collect data, the General Data Protection Regulation (GDPR) and national regulations can apply. It is essential that the smart protective garments are selected, used, taken care and maintained in a way that will neither compromise the safety and privacy of the user nor the security of the enterprise or authority using the smart garment systems.
- Technical report94 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
The purpose of this document is to assist employers (or the person who advises the employer such as suppliers of PPE or services, inspection, insurance companies, etc.) in taking the necessary decisions regarding the selection, use, care and maintenance (SUCAM) of advanced garments and ensembles of garments that provide protection against heat and flame, with integrated smart textiles and smart non-textile elements for enhanced health, safety and survival capabilities that are compliant with the European legislation.
This document supports developers and manufacturers in designing and producing garments with smart textiles and smart non-textile elements that will meet the user’s needs during the whole life cycle of the garment and comply with standard requirements set for protective clothing on use, care and maintenance up to and including the disposal of the protective gear.
This document is not exhaustive in addressing all the safety concerns associated with the use of compliant protective equipment for protection against heat and flames and other related risks.
It is essential not to construe this document as addressing all the safety concerns, if any, associated with the use of this document by testing or repair facilities. It is the responsibility of the persons and organizations that use this document and any other standards or technical report related to PPE:
- to conduct a risk assessment at the workplace;
- to select the protective clothing and other PPE, including those with smart (intelligent) features, and to verify that the manufacturer has indicated the selected PPE to be suitable for the identified risks at the workplace;
- as well as to ensure that these provide a holistic protection, only when the compatibility has been assessed including understanding the workplace and the work environment to determine the properties of protective clothing against heat and flames to establish health and safety practices;
- to verify that the manufacturer has provided information for risk assessment of the potential risks that may occur due to the smart (intelligent) features in the intended working environment, and that the manufacturer has suggested measurements to compensate such new risks, whilst the employer has to ensure that these measurements are brought to action;
- and to determine the applicability of regulatory limitations prior to using this document for any designing, manufacturing, and testing.
This document is meant for all end users that are using smart garments for protection against heat and flame. It contains information that can also be useful to other people, such as manufacturers, designers, service providers and educators who may be confronted with smart garments used to protect against heat and flame risks although it will focus on the first four in the list below:
- petrochemical and chemical industry;
- welders and foundries;
- utilities (electrical, gas, water);
- firefighters and emergency response;
- sports (motor sports, boating, etc.);
- security forces (military, police and private).
It is essential that nothing herein restricts any jurisdiction from exceeding the minimum requirements as provided in the relevant standards.
This document is not intended to cover the aspects related to data security and privacy. For employers using smart garments that monitor and/or collect data, the General Data Protection Regulation (GDPR, Regulation (EU) 2016/679) and national regulations can apply. It is essential that the smart protective garments are selected, used, taken care and maintained in a way that will neither compromise the safety and privacy of the user nor the security of the enterprise or authority using the smart garment systems.
- Technical report94 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method to measure the repellency, retention and penetration of a known volume of liquid pesticide when applied to a protective clothing material. No external hydrostatic or mechanical pressure is applied to the test specimen during or after the application of the liquid pesticide. The degree of contamination depends on numerous factors such as the type of exposure, application technique, and pesticide formulation. As the level of exposure can vary considerably, this method is designed to rate the relative performance of personal protective equipment (PPE) materials at two levels of contamination. Low level of contamination is achieved by applying 0,1 ml of liquid formulation and high level by applying 0,2 ml. This test method does not measure the resistance to permeation or degradation. This test method is suitable for field strength and concentrated pesticide formulations. This method may not be suitable for testing protective clothing materials against volatile pesticide formulations. This document is applicable to the evaluation of materials that are new or those that have undergone treatment such as laundering or simulated abrasion. Details of the treatment shall be reported. This test method can also be used to determine the resistance provided by protective clothing materials against penetration of new pesticide formulations.
- Standard16 pagesEnglish languagesale 15% off
- Standard16 pagesEnglish languagesale 15% off
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageFrench languagesale 15% off
This European Standard establishes requirements for the management and control of operational activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This part covers the management and control of rehabilitation activities.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies minimum performance requirements for protective clothing designed to be worn during firefighting activities. The requirements detailed in this document cover design, heat and flame, mechanical, chemical, comfort, and visibility.
This document covers the general clothing design, the minimum performance levels of the material used, the methods of test to be used to determine these performance levels, marking and information supplied by the manufacturer.
This document makes distinction between firefighting activities dividing them into two performance levels based on a risk assessment:
- Level 1: specifies the minimum requirements for firefighting clothing involving work associated with outdoor firefighting and their support activities, taking into account the environments and conditions of the expected operational scenarios of such firefighting activities.
The level 1 is not applicable for protection against risks encountered in fighting fires or rescue from fire activities in structures, unless combined to a level 2 or other specialized PPE.
- Level 2: specifies the minimum requirements for firefighting clothing for risks encountered in fighting fires and rescue from fire in structures.
The distinction between Level 1 and Level 2 clothing is restricted to the requirements for heat and flame (X1 or X2 - Heat and Flame). These levels of protection can be reached by a single garment or a combination of separate garments.
Additional marking provides two grades of protection for Y (protection against water penetration) and Z (water vapour resistance). It is essential that these performance grades are indicated on the marking of the clothing and explained in the instructions for use.
This document does not cover protective clothing for wildland firefighting, specialized firefighting in a high amount of radiant heat where reflective clothing is required and/or advanced technical rescue operations dealing with hazardous chemicals, working with chainsaws and water and rope rescue.
This document does not cover protection for the head, hands and feet or specific protection against other hazards e.g. chemical, biological, radiological and electrical hazards. These aspects may be covered in other European Standards.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods of test and minimum performance requirements for personal protective clothing, designed to protect the wearer's body, except for the head, hands, and feet, that is worn during wildland firefighting and associated activities. This clothing is not intended to provide protection during fire entrapment. This document covers the general design of the garment, the minimum level of performance for the materials employed and the methods of test to determine these levels.
This document is not applicable to clothing for use in situations encountered in structural firefighting (EN 469 or ISO 11999-3), rescue (ISO 18639) or where a high level of infrared radiation is expected (ISO 15538 or EN 1486), nor does this document cover clothing to protect against chemical, biological, electrical or radiation hazards. This document does not provide protection against high mechanical risks such as for protection when using chain saws.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This Standard specifies the optical performance requirements for high-visibilty clothing to be worn by adults and by juveniles, and designed for non-professional use. High-visibility clothing for non-professional use is intended to signal the user's presence visually in any daylight condition and, when illuminated by vehicle headlights or search lights in the dark as well as lit up in urban roads. This standard is not applicable to accessories to be carried by persons or attached to garments.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies minimum performance requirements for protective clothing designed to be worn during firefighting activities. The requirements are detailed in this document covering heat and flame, mechanical, chemical, comfort, visibility, etc.
This document covers the general clothing design, the minimum performance levels of the material used, the methods of test to be used to determine these performance levels, marking and information supplied by the manufacturer.
This document makes distinction between firefighting activities dividing them into two performance levels based on a risk assessment:
- Level 1: specifies the minimum requirements for firefighting clothing involving work associated with outdoor firefighting and their support activities, taking into account the environments and conditions of the expected operational scenarios of such firefighting activities.
The level 1 is not applicable for protection against risks encountered in fighting fires or rescue from fire activities in structures, unless combined to a level 2 or other specialised PPE.
- Level 2: specifies the minimum requirements for firefighting clothing for risks encountered in fighting fires and rescue from fire in structures.
The distinction between Level 1 and Level 2 clothing is restricted to the requirements on heat and flame (X1 or X2 - Heat and Flame). These levels of protection can be reached by a single or a combination of separate garments.
Additional marking provides two grades of protection for Y (protection against water penetration) and Z (water vapour resistance). It is essential that these performance grades are indicated on the marking of the clothing and explained in the instructions for use.
This document does not cover protective clothing for specialized tasks or specific risk situations e.g. wildland firefighting, specialized firefighting and/or advanced technical rescue operations dealing with hazardous chemicals, working with chainsaws and water and rope rescue.
This document does not cover protection for the head, hands and feet or specific protection against other hazards e.g. chemical, biological, radiological and electrical hazards. These aspects may be covered in other European Standards.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day