49.025.20 - Aluminium

This document specifies the acid pickling of aluminium and aluminium alloys free from hexavalent chromium.

This document specifies the acid pickling of aluminium and aluminium alloys free from hexavalent chromium.

This document specifies the characteristics, test methods, qualification and acceptance conditions of single and multicore electric cables for general purpose with conductors in aluminium or copper-clad aluminium, intended for installation in aircraft electrical systems. The insulation of these cables is designed to withstand aircraft voltages at a frequency not exceeding 2 000 Hz. Unless specified by individual product standards the maximum demonstrated voltage of rating of these cables is ac 1...view more

This document defines the requirements for hexavalent chromium free anodizing of aluminium and
aluminium alloys for corrosion protection, bonding and painting.
Hard anodizing and plasma electrolytic anodizing (micro-arc oxidation) are not covered by this
document.
The purpose of this document is to give design, quality and manufacturing requirements. It does not give
complete in-house process instructions; these are given in the processors detailed process instructions.

This document specifies the requirements relating to: Aluminium alloy 6082- T6 Tubes for structures 0,6 mm ≤ a ≤ 12,5 mm

This document defines the requirements for hexavalent chromium free anodizing of aluminium and aluminium alloys for corrosion protection, bonding and painting.
Hard anodizing and plasma electrolytic anodizing (micro-arc oxidation) are not covered by this document.
The purpose of this document is to give design, quality and manufacturing requirements. It does not give complete in-house process instructions; these are given in the processors detailed process instructions.

This document specifies the requirements relating to: Aluminium alloy Al-P16- T6151 Plates 6 mm < a ≤ 120 mm.

This document defines the nature of and the surface preparation method for test pieces in aluminium alloys intended for testing paints and varnishes used for aerospace applications. 2 Normative

This document specifies the requirements relating to:
Aluminium alloy Al-P16-
T6151
Plates
6 mm < a ≤ 120 mm
for aerospace applications.

This document specifies the requirements relating to:
Aluminium alloy 2024 - -
T3
Extruded bar and section
1,2 mm ≤ (a or D) ≤ 150 mm
with coarse peripheral grain control
for aerospace applications.

This European Standard specifies the characteristics of electrical wires AZ family for use in the on board:
   115 V (phase to neutral) or 200 V (phase to phase) electrical network of aircraft.
   230 V (phase to neutral) or 400 V (phase to phase) electrical network of aircraft and particularly use in non-pressurized areas.
This cable family is used at operating temperature between  65 °C and 180 °C.

This European Standard specifies the characteristics of electrical wires AZA family for use in the on board:
   115 V (phase to neutral) or 200 V (phase to phase) electrical network of aircraft.
   230 V (phase to neutral) or 400 V (phase to phase) electrical network of aircraft and particularly use in non-pressurized areas.
This cable family is used at operating temperature between  65 °C and 180 °C.

This document specifies the requirements relating to:
Aluminium alloy 2024-
T42
Drawn tubes for structural applications
for aerospace applications.

This document specifies the requirements relating to:
Aluminium 1050A-H14
Wire for solid rivets
D ≤ 10 mm
for aerospace applications.

This document specifies the requirements relating to:
Aluminium 1050A-H14
Wire for solid rivets
D ≤ 10 mm
for aerospace applications.

This document specifies the requirements relating to:
Aluminium alloy 2024 - -
T3
Extruded bar and section
1,2 mm ≤ (a or D) ≤ 150 mm
with coarse peripheral grain control
for aerospace applications.

This document specifies the requirements relating to:
Aluminium alloy 2024-
T42
Drawn tubes for structural applications
for aerospace applications.

This European Standard defines the requirements for the ordering, manufacture, testing, inspection and
delivery of aluminium and aluminium alloy plate, clad or unclad, supplied in the as-rolled or machined
condition. It shall be applied when referred to and in conjunction with the EN material standard unless
otherwise specified on the drawing, order or inspection schedule.

This European Standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of aluminium and aluminium alloy sheet and strip, clad or unclad. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

This European Standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of aluminium and aluminium alloy, bar and section, produced by extrusion, rolling or drawing. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.