SIST EN 2125:2019

Aerospace series - Aluminium alloy Al-P16 - T6151 - Plates 6 mm < a ≤ 120 mm

This document specifies the requirements relating to: Aluminium alloy Al-P16- T6151 Plates 6 mm < a ≤ 120 mm.

Luft- und Raumfahrt - Aluminium-legierung Al-P16 - T6151 - Platten 6 mm < a ≤ 120 mm

Série aérospatiale - Alliage d'aluminium Al-P16 - T6151 - Tôles épaisses 6 mm < a ≤ 120 mm

Le présent document spécifie les exigences relatives à :
Alliage d’aluminium Al-P16-
T6151
Tôles épaisses
6 mm < a ≤ 120 mm
pour applications aérospatiales.

Aeronavtika - Aluminijeva zlitina Al-P16 - T6151 - Plošče 6 mm < a ≤ 120 mm

Ta dokument določa zahteve, ki se navezujejo na: plošče 6 mm < a ≤ 120 mm iz aluminijeve zlitine Al-P16 – T6151.

General Information

• Status: Published
• Publication Date: 16-Sep-2019
• ICS: 49.025.20 - Aluminium
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Sep-2019
• Due Date: 18-Nov-2019
• Completion Date: 17-Sep-2019
• Ref Project: EN 2125:2019 - Aerospace series - Aluminium alloy Al-P16- - T6151 - Plates - 6 mm < a ≤ 120 mm

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 2125:2019
01-november-2019
Aeronavtika - Aluminijeva zlitina Al-P16 - T6151 - Plošče 6 mm < a ≤ 120 mm
Aerospace series - Aluminium alloy Al-P16 - T6151 - Plates 6 mm < a ≤ 120 mm
Luft- und Raumfahrt - Aluminium-legierung Al-P16 - T6151 - Platten 6 mm < a ≤ 120 mm
Série aérospatiale - Alliage d'aluminium Al-P16 - T6151 - Tôles épaisses 6 mm < a ≤ 120
mm
Ta slovenski standard je istoveten z: EN 2125:2019
ICS:
49.025.20 Aluminij Aluminium
SIST EN 2125:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 2125:2019

---------------------- Page: 2 ----------------------
SIST EN 2125:2019


EN 2125
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2019
EUROPÄISCHE NORM
ICS 49.025.20
English Version

Aerospace series - Aluminium alloy Al-P16- - T6151 -
Plates - 6 mm < a ≤ 120 mm
Série aérospatiale - Alliage d'aluminium Al-P16- - Luft- und Raumfahrt - Aluminiumlegierung Al-P16- -
T6151 - Tôles épaisses - 6 mm ≤ a ≤ 120 mm T6151 - Bleche - 6 mm < a ≤ 120 mm
This European Standard was approved by CEN on 14 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2125:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 2125:2019
EN 2125:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 5

2

---------------------- Page: 4 ----------------------
SIST EN 2125:2019
EN 2125:2019 (E)
European foreword
This document (EN 2125:2019) has been prepared by the Aerospace and Defence Industries Association
of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall be
withdrawn at the latest by March 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Repu
...